Randomized controlled within-subject evaluation of digital and conventional workflows for the fabrication of lithium disilicate single crowns. Part III: marginal and internal fit |
| |
Authors: | Marco Zeltner Irena Sailer Sven Mühlemann Mutlu Özcan Christoph H.F. Hämmerle Goran I. Benic |
| |
Affiliation: | 1. Postgraduate student, Clinic of Fixed and Removable Prosthodontics and Dental Material Science, Center of Dental Medicine, University of Zurich, Zurich, Switzerland;2. Professor, Division of Fixed Prosthodontics and Biomaterials, University Center of Dental Medicine, University of Geneva, Geneva, Switzerland;3. Senior Teaching and Research Assistant, Clinic of Fixed and Removable Prosthodontics and Dental Material Science, Center of Dental Medicine, University of Zurich, Zurich, Switzerland;4. Professor, Clinic of Fixed and Removable Prosthodontics and Dental Material Science, Center of Dental Medicine, University of Zurich, Zurich, Switzerland;5. Professor, Clinic of Fixed and Removable Prosthodontics and Dental Material Science, Center of Dental Medicine, University of Zurich, Zurich, Switzerland;6. Senior Teaching and Research Assistant, Clinic of Fixed and Removable Prosthodontics and Dental Material Science, Center of Dental Medicine, University of Zurich, Zurich, Switzerland |
| |
Abstract: | Statement of problemTrials comparing the overall performance of digital with that of conventional workflows in restorative dentistry are needed.PurposeThe purpose of the third part of a series of investigations was to test whether the marginal and internal fit of monolithic crowns fabricated with fully digital workflows differed from that of crowns fabricated with the conventional workflow.Material and methodsIn each of 10 participants, 5 monolithic lithium disilicate crowns were fabricated for the same abutment tooth according to a randomly generated sequence. Digital workflows were applied for the fabrication of 4 crowns using the Lava, iTero, Cerec inLab, and Cerec infinident systems. The conventional workflow included a polyvinyl siloxane impression, manual waxing, and heat-press technique. The discrepancy between the crown and the tooth was registered using the replica technique with polyvinyl siloxane material. The dimensions of the marginal discrepancy (Discrepancymarginal) and the internal discrepancy in 4 different regions of interest (Discrepancyshoulder, Discrepancyaxial, Discrepancycusp, and Discrepancyocclusal) were assessed using light microscopy. Post hoc Student t test with Bonferroni correction was applied to detect differences (α=.05).ResultsDiscrepancymarginal was 83.6 ±51.1 μm for the Cerec infinident, 90.4 ±66.1 μm for the conventional, 94.3 ±58.3 μm for the Lava, 127.8 ±58.3 μm for the iTero, and 141.5 ±106.2 μm for the Cerec inLab workflow. The differences between the treatment modalities were not statistically significant (P>.05). Discrepancyshoulder was 82.2 ±42.4 μm for the Cerec infinident, 97.2 ±63.8 μm for the conventional, 103.4 ±52.0 μm for the Lava, 133.5 ±73.0 μm for the iTero, and 140.0 ±86.6 μm for the Cerec inLab workflow. Only the differences between the Cerec infinident and the Cerec inLab were statistically significant (P=.036). The conventionally fabricated crowns revealed significantly lower values in Discrepancycusp and Discrepancyocclusal than all the crowns fabricated with digital workflows (P<.05).ConclusionsIn terms of marginal crown fit, no significant differences were found between the conventional and digital workflows for the fabrication of monolithic lithium disilicate crowns. In the occlusal regions, the conventionally manufactured crowns revealed better fit than the digitally fabricated crowns. Chairside milling resulted in less favorable crown fit than centralized milling production. |
| |
Keywords: | Corresponding author: Dr Goran I. Benic Clinic of Fixed and Removable Prosthodontics and Dental Material Science Center of Dental Medicine University of Zurich Plattenstrasse 11 CH-8032 Zurich SWITZERLAND |
本文献已被 ScienceDirect 等数据库收录! |
|