Standard versus customised locking plates for fixation of schatzker ii tibial plateau fractures

Aim3D-printed implants could improve the capture of fracture fragments for improved stability of tibial plateau fracture fixation. The aim of this study was to compare the biomechanical strength of fixation constructs using standard and customised 3D-printed proximal tibial locking plates for fixation of tibial plateau fractures.MethodsThis is a biomechanical study utilising six pairs of cadaveric tibiae. Fractures were created in an identical fashion using an osteotome and mallet, and fixed using either a standard, commercially-available proximal tibia locking plate or a customised 3D-printed plate. Design and production of the customised plates followed a “3D printing at point-of-care” model. Customised stainless steel 316 L plates were produced within a local additive manufacturing laboratory based upon pre-operative CT scans. Determination of implant choice within each cadaver pair was performed via simple randomisation. Following fracture fixation, the tibiae were skeletalised and biomechanically tested using a customised loading jig and a size-matched femoral knee prosthesis. The constructs were loaded cyclically from 100 N to approximately three times the cadaveric body-weight at 5 Hz for 10 000 cycles. Every 1000 cycles, the test was paused and the tibia was physically checked for failure. If failure had not occurred by the end of the testing cycle, the construct was loaded to failure and the load at which the construct failed was noted.ResultsFixation constructs using the 3D-printed plates performed comparably to those using the standard plates. There was no significant difference in the degree of fracture fragment displacement in both constructs. Overall longitudinal construct stiffness and load to failure was higher in the 3D-plates group but this did not reach statistical significance.ConclusionProduction of customised plates for proximal tibia fractures at point-of-care is feasible, however fixation constructs with these plates did not provide any biomechanical advantage over standard plates in terms of axial loading stiffness.     

Same-Day Repeat Hepatopulmonary Shunt Measurement during Planning Angiography for Hepatic Radioembolization

This report describes a technique for measuring lung shunt fraction (LSF) twice in a single session during planning arteriography for radioembolization using low and standard dose technetium-99m macroaggregated albumin (^99mTc-MAA). A patient with a 16.0 cm hepatocellular carcinoma and LSF of 70% was treated with lenvatinib for 4 weeks. Planning arteriography with administration of 0.5 millicuries of ^99mTc-MAA was then performed. Arterial access was maintained while the LSF was calculated, which was persistently elevated at 54%. Embolization of arteriovenous shunts was performed during the same session and 5.0 millicuries of ^99mTc-MAA were administered. The repeat LSF was 29%. Successful radioembolization was subsequently performed.     

甲状腺~(99)Tc~mO_4~-显像冷结节的临床诊断价值

目的　探讨甲状腺99TcmO-4 显像冷结节对不同性质甲状腺疾病的诊断价值。方法　采用静脉注射99TcmO-4 185MBq ,2 0min后甲状腺前位静态显像 ,采集总计数 1× 10 6。显像显示甲状腺结节局部放射性分布缺损或低于正常甲状腺组织则定性为冷结节。结果　 34 2例甲状腺99TcmO-4 显像发现冷结节 85例 ,发生率为2 4.9% ,85例冷结节中 ,37例 (4 3.5 % )为甲状腺瘤 ,15例为甲状腺癌 (17.6 % ) ,2 0例 (2 3.5 % )为结节性甲状腺肿 ,8例 (9.4% )为甲状腺炎 ,4例 (4 .7% )为单纯性甲状腺囊肿 ,1例 (1.3% )为甲状腺外肿物。结论　冷结节在甲状腺99Tcm O-4 显像时较为常见 ,且不同性质甲状腺疾病的冷结节及其周围组织有一定的特征性表现 ,因此99TcmO-4显像冷结节对甲状腺腺瘤、甲状腺癌、甲状腺囊肿、甲状腺炎等常见疾病具有较高的临床价值。     

顺铂聚乳酸微球的药物释放特性及肝动脉栓塞研究

对顺铂聚乳酸微球进行了体外药物释放和家犬肝动脉栓塞研究。该微球粒径范围为50～200μm,平均粒径为115.76±35.94μm,顺铂含量为37.16%(W/W);体外药物释放机制符合Higuchi方程;肝动脉栓塞后8h,肝组织顺铂浓度高达21.55±12.18μg/g,明显高于肝动脉灌注顺铂组:3.16±0.09μg/g(P<0.05);肝动脉栓塞组的顺铂血浓峰值、各取血点浓度及曲线下面积AUC皆低于肝动脉灌注顺铂组。可望达到提高栓塞部位的药物疗效,降低全身毒副反应的作用。     

Bone scintigraphy in hereditary mutiple exostoses

A case of hereditary mutiple exostoses is presented. ^99mTc-MDP imaging demonstrated uptake of radiotracer in the lesions.     

无创伤性测定门静脉压力与肝血流二法联合应用研究肝硬化的价值

目的　为临床研究肝硬化提供有价值的手段。方法　采用99mTc -RBC测定 93例肝硬化患者肝血流 ,选择峰时 (Tmax) ,半廓清时 (T1/2 )、廓清率 (K值 )、肝血流 (LBF)等作为观察指标 ,与正常对照组比较 ;同时用99mTc-MIBI经直肠给药测定其中 5 4例患者门静脉压力 (PVP) ,以心 /肝 (H/L)比值作为分流指数。结果　肝硬化组Tmax、T1/2 、K及LBF分别为 1.2 6± 0 .99(93)min、5 .75± 3.38(93)min、0 .15 4± 0 .116 (93)及 0 .6 10± 0 .2 89(93)L/min ,除Tmax外 ,与对照组均有非常显著性差异 ;Child -A、B、C级各组之间 (除Tmax外 )也均有非常显著性差异或显著性差异 ;Child -A、B、C级各组H/L分别为 0 .49± 0 .18(2 1)、0 .6 9± 0 .16 (15 )、0 .91± 0 .2 1(18) ;PVP分别为 2 .2 2± 0 .5 7(2 1)kPa、2 .85± 0 .38(15 )kPa及 3.5 4± 0 .6 5 (18)kPa。而对照组的H/L及PVP分别为 0 .30± 0 .12 (16 )及 1.6 1± 0 .38(16 )kPa。Child -A、B、C级各组分别与对照组及各组之间比较 ,除Child -B与C级组PVP无显著性差异 (P >0 .0 5 )外 ,其余均有非常显著性差异 (P <0 .0 1)及显著性差异 (P <0 .0 5 )。结论　本法测定肝血流及门脉压力方便 ,无创伤 ,对分析病情 ,判断疗效 ,指导制订治疗方案 ,估计预后等均有较     

~(99)Tc-MDP对类风湿性关节炎患者外周血单核细胞产生细胞因子的影响

目的 :探讨“云克”(99Tc MDP)治疗类风湿性关节炎 (RA)的免疫机制。方法 :采用ELISA双抗体夹心法 ,观察“云克”体外对RA患者外周血单核细胞 (PBMC)产生白介素 1(IL 1)和可溶性白介素 2受体 (sIL 2R)的影响。结果 :“云克”有抑制RA患者IL 1的分泌及细菌脂多糖 (LPS)的促分泌作用 ,并对可溶性白介素 2受体的自发分泌及植物血素 (PHA)诱导分泌均有抑制作用。结论 :“云克”对RA的治疗机制可能与其降低IL 1和sIL 2R的作用有关     

腮腺显像对鼻咽癌放疗后腮腺功能的评价

目的利用腮腺显像研究鼻咽癌放疗后腮腺的摄取与排泄功能.方法48例鼻咽癌患者中,对38例肿瘤和肿大淋巴结行加速调强放疗（SMART）,其亚临床灶和预防照射区接受常规照射;余10例行常规放疗.放疗前后均行腮腺显像,计算腮腺的放射性摄取指数（UI）及酸性刺激后排泌指数（EI）,对腮腺功能损伤情况进行分析;同时记录患者口干程度并分级.结果鼻咽癌SMART组放疗后腮腺UI和EI分别下降21.9%和37.3%,中重度口干者12例;而常规放疗组腮腺功能明显下降,UI和EI分别下降56.1%和96.1%,中重度口干者9例,两者比较差异均有显著性（P＜0.05）.结论腮腺显像可灵敏地监测鼻咽癌放疗后腮腺功能.     

门控心肌显像结合GS Quant软件评价左室功能

目的:评价GS Quant软件结合99mTc-甲氧基异TN(MtBI)门控心肌断层显像(G-SPECT)测定左室射血分数(LVEF)的价值。方法:选择24例于同期2周内完成G-SPECT、门控心血池显像(RNA)和超声心动图检查(UCG)的患者,比较3种方法所测定的LVEF值。结果:99mTc-MIBI G-SPECT所测得的LVEF值与RNA和UCG法所测得的LVEF值均有较好的相关性,相关系数r分别为0.81(P<0.05)和0.76(P<0.05)。结论:99mTc-MIBI G-SPECT所测定的LVEF值有很好的准确性和可重复性,具有较高的临床应用价值,可进一步推广应用门控核素心肌断层显像这一技术。