麻醉机呼吸环路碱石灰尘埃污染的情况

目的：观察通气时碱石灰尘埃向呼吸环路中的排放及被呼吸道阻留的情况。方法：麻醉机环路连接集尘袋及筛装新碱石灰。ＪＴ库尔特颗粒计数仪动态测定排尘量。其颗粒测量范围为１～１２５μｍ３，通气１０分后测定呼吸环路加集尘袋内的尘埃量即为总尘量，收取称干重得尘埃分散度。通过对Ｎａｒ－ｃｏｍｅｄ、Ｄｒａｇｅｒ、Ｓｕｌａｒ８０８和１０３麻醉机行上述测量后，另以前者（Ｎ机）为例，其环路按相应处理分干燥、湿化和过滤三组，志愿者模拟通气１０分测定环路含尘量后与总尘量差得气管肺的阻留量。结果：四种麻醉机环路内碱石灰尘埃的分散度达１３ｍｇ／ｍ３以上。尘埃排放量与通气时间呈正比（ｒ＝０．９５，Ｐ＜０．０１）。Ｎ机干燥组中总排尘量的半数以上被气管肺阻留。湿化组该阻留量明显下降（Ｐ＜０．０５），而过滤组环路内总排尘量和气管肺阻流量下降更为显著（Ｐ＜０．０１）。结论：使用新碱石灰通气时，麻醉机环路内存在严重的尘埃污染，环路内湿化有一定的防尘作用，但以滤过处理效佳。     

石灰水对埃及伊蚊不同发育阶段影响研究

目的通过石灰水对埃及伊蚊生活史幼期不同阶段生长发育影响的实验室研究,评价生石灰对防治埃及伊蚊的干预效果,为生石灰用于埃及伊蚊的防治提供实验数据。方法将一定数量的埃及伊蚊依据不同发育阶段(卵、Ⅰ~Ⅳ龄期蚊幼、蛹)分别饲养于石灰水中,观察蚊幼活动情况,记录不同时期相应孵化时间、孵化率和死亡率,同时将实验室过夜自来水(实验室脱氯水)饲养蚊虫作对照,分析比较不同饲养环境、不同发育阶段埃及伊蚊发育的变化差异。结果对照组埃及伊蚊卵的平均孵化时间为1.75 d,而试验组(1.3 g/L石灰水饲养)埃及伊蚊卵的平均孵化时间为3.84 d,是对照组的2.19倍,孵化时间的差异具有统计学意义(t=36.02,P<0.05)。试验组埃及伊蚊卵孵化率为59.3%,对照组为89.3%,两组之间孵化率的差异具有统计学意义(χ^(2)=35.38,P<0.05)。Ⅰ~Ⅳ龄试验组蚊幼死亡率分别为44.0%、92.0%、97.3%、98.7%,显著高于对照组蚊幼死亡率,两组之间死亡率的差异具有统计学意义(χ^(2)值为65.79~276.53,P<0.05)。试验组蛹的死亡率为98.7%,显著高于对照组的死亡率,两组之间死亡率的差异具有统计学意义(χ^(2)=280.35,P<0.05)。对照组埃及伊蚊卵、蚊幼和蛹的死亡率分别为10.7%、2.3%和2.0%,三组之间死亡率的差异具有统计学意义(χ^(2)=25.09,P<0.05)。对照组埃及伊蚊卵的死亡率明显高于蚊幼和蛹。试验组埃及伊蚊卵、蚊幼和蛹的死亡率分别为40.7%、83.0%和98.7%,三组之间死亡率差异具有统计学意义(χ^(2)=170.88,P<0.05)。结论石灰水对埃及伊蚊不同发育阶段均具有明显抑制作用,对蛹的杀灭作用最大,其次是蚊幼和卵。随着埃及伊蚊幼虫年龄的增长,石灰水对其抑制效果逐渐增强。但生石灰对埃及伊蚊成蚊的防治效果有待进一步的现场验证。     

Cytotoxic and Antibacteriial Actiivity of the Mixture of Olive Oil and Lime Cream in Vitro Conditions

The mixture of olive oil and lime cream has been traditionally used to treat external burns in the region of Hatay/Antakya and middle Anatolia. Olive oil and lime cream have been employed by many physicians to treat many ailments in the past. A limited number of studies have shown the antibacterial effect of olive oil and that it does not have any toxic effect on the skin. But we did not find any reported studies on the mixture of olive oil and lime cream. The aim of this paper is to investigate the cytotoxic and antibacterial activity of olive oil and lime cream individually or/and in combination in vitro conditions, by using disk-diffusion method and in cell culture. The main purpose in using this mixture is usually to clear burns without a trace. Agar overlay, MTT (Cytotoxicity assay) and antibacterial susceptibility tests were used to investigate the cytotoxic and antibacterial activity of olive oil and lime cream. We found that lime cream has an antibacterial activity but also cytotoxic on the fibroblasts. On the other hand olive oil has limited or no antibacterial effect and it has little or no cytotoxic on the fibroblasts. When we combined lime cream and olive oil, olive oil reduced its cytotoxic impact. These results suggest that mixture of olive oil and lime cream is not cytotoxic and has antimicrobial activity.     

In vivo anti-plasmodial activities and toxic impacts of lime extract of a combination of Picralima nitida,Alstonia boonei and Gongronema latifolium in mice infected with Chloroquine-sensitive Plasmodium berghei

Background

Lime extracts of powdered combination of seeds of Picralima nitida, stem bark of Alstonia boonei and leaves of Gongronema latifolium is a common remedy used in the treatment of malaria in South Western Nigeria.

Objective

To determine the antiplasmodial activities of the combined herbal extracts and its impact on the haematological, hepatological and renological parameters in mice.

Methods

The 4-day suppressive and curative tests were used to assess the antiplasmodial activities of the extract in mice infected with chloroquine-sensitive Plasmodium berghei at concentration of 200mg/kg, 400mg/kg and 800mg/kg body weight. The haematological parameters including red blood cells, white blood cells, packed cell volume and haemoglobin count were analysed with an auto analyser. The activities of alanine aminotransferase (ALT), aspartate aminotransferase (AST) and alkaline phosphatase (ALP) were determined, while urea, protein and creatinine were analysed by standard procedural methods.

Results

The 4-day suppressive test revealed that the test extract achieved percentage suppression of 39.0%, 41.6% and 54.68% for the 200mg/kg, 400mg/kg and 800mg/kg concentration respectively. Additionally, the curative test achieved a high percentage suppression of 80.97%, 83.84% and 86.16% at the 200mg/kg, 400mg/kg and 800mg/kg concentration respectively. The extracts did not induce significant change on haematological parameters (P>0.05), while significant elevation in the values of the ALT and AST (P<0.05) was observed and elevation of creatinine (P<0.05) at 800mg/kg.

Conclusions

The results support the traditional use of the herbal combination in the treatment of malaria, however the liver cells were impacted by the extracts in bioassay conducted with mice.     

Mechanical and Durability Performance Improvement of Natural Hydraulic Lime-Based Mortars by Lithium Silicate Solution

Natural hydraulic lime (NHL) as a building material has been widely used to restore the historic structure. However, the slow growth rate of strength and durability limits its engineering application. In this work, the NHL-based mortars were pretreated by lithium silicate (LS) solution impregnation and surface spraying. The results show that the compressive strength, surface hardness, and freeze-thaw cycle (FTC) resistance of NHL-based mortar were greatly improved after LS pretreatment. Specifically, the compressive strengths of the sample increased by about 32.7–52.0%. LS was sprayed on the sample’s surface (about 0.2 kg/m²) and the surface hardness increased by up to 10 grades. Compared with the control samples, the weight loss of treated samples decreased by about 31.6–43.8%. A rehydration process to generate the hydrated calcium silicate gel (C-S-H) was observed between calcium hydroxide (CH) and LS, which can decrease the sample’s porosity and form a silicate coating on the surface. With an increase in the concentration of LS, the macropores (50–10,000 nm) content decreased, while the mesopores (10–50 nm) and nanopores (less than 10 nm) increased. This work reveals that the LS pretreatment provides a potential route to improve NHL-based mortar’s mechanical properties and durability.     

Potential of Using Wood Biomass Ash in Low-Strength Composites

Reducing greenhouse gas emissions and dependence on fossil fuels is the cornerstone of all European climate and energy strategies. Consequently, renewable energy sources are becoming more competitive with fossil fuels. The largest source of bioenergy in the European Union is biomass-fired power plants. Therefore, the European coal phase-out strategy led to an increased use of wood biomass as a sustainable fuel, generating large amounts of wood biomass ash (WBA). In the research studies reported so far, WBA has been mainly used in cementitious composites. However, given the similarities between the chemical composition of WBA and hydraulic lime (HL), this research focused on its potential classification as a building lime. Overall, three different sources of fly WBA were considered for the preparation of binders as mixtures of WBA and coal fly ash (CFA) in different ratios. The contribution of each binder mixture on the paste and mortar properties was analyzed based on the chemical composition, setting time, volume stability, and contribution to the mortar strength (compressive and flexural). In general, it can be concluded that the studied binders can meet the criteria of EN 459-1. However, special attention should be paid to the volume deformations and the setting time.     

Comparative Study of Effects of Air-Entraining Plasticizing Admixture and Lime on Physical and Mechanical Properties of Masonry Mortars and Plasters

This article presents research on selected physical and mechanical properties of cement-based plasters and masonry mortars with consistency-improving additives, namely, traditional hydrated lime and a plasticizing and aerating mixture (APA), which, in practice, is often considered to be a lime substitute. Comparative analysis of the properties of mortars with alternative additives—lime or APA—was carried out, taking into consideration possible effects of cement, as two types of Portland cement were used for the research. For fresh mortar, mixture consistency, air content, resistance to segregation, and water retention were determined. Tests on hardened mortars included tests of porosity and impermeability, depth of penetration of water under pressure, drying shrinkage, as well as compressive and bending strength, modulus of elasticity, and adhesion of mortars to the base. In addition, research has shown that cement–lime mortars and cement mortars with APA admixture of similar consistency in the fresh state are characterized by significantly different properties. The results show, in most of the features analyzed, more favorable properties of mortars with the use of traditional lime. For shrinkage only, the use of admixture turned out to be more advantageous.     

Evaluation of Disposal Stability for Cement Solidification of Lime Waste

The Korea Atomic Energy Research Institute (KAERI) obtains UO₂ powder using the ammonium uranyl carbonate (AUC) wet process. Hydrated lime (Ca(OH)₂) is used to neutralize liquid wastes produced from the AUC process, and the resulting byproduct is known as lime waste. The purpose of this study is to determine optimum operating conditions for cementation of radioactive lime waste produced from the AUC process, and to evaluate the structural stability and leaching stability of cement waste form. The waste acceptance criteria (WAC) of a waste disposal facility in Korea were used to evaluate the cement waste form samples. The maximum lime waste content guaranteeing the shape stability of cement waste form was found to be 80 wt.% or less. Considering the economic feasibility and error of the cementation process, the optimum operating conditions were achieved at a lime waste content of 75 wt.% and a water-to-cement (w/c) ratio of 2.0. The compressive strength of cement waste form samples prepared under optimal operating conditions was 61.4, 76.3, and 61.0 kgf/cm² after the thermal cycling test, water immersion test, and irradiation, respectively, satisfying the compressive strength of 35.2 kgf/cm² specified in WAC. A leaching test was performed on the samples, and the leachability indexes (LX) of Cs, Sr, and Co nuclides were 7.63, 8.02, and 10.89, respectively, which are all higher than the acceptance criterion of 6. The results showed that the cement waste forms prepared under optimal operating conditions satisfied the WAC in terms of structural stability and leaching stability. As such, the proposed cement solidification method for lime waste disposal can be effective in solidifying lime waste powder produced during the neutralization of liquid wastes in the AUC process.     

Physical Properties of an Eco-Sustainable,Form-Stable Phase Change Material Included in Aerial-Lime-Based Mortar Intended for Different Climates

The aim of this experimental investigation was to produce a form-stable phase change material (PCM) able to reduce the need for nonrenewable energy resources required for the heating/cooling of buildings located in regions characterized by different climatic conditions. The innovative PCM must also be sustainable and must be produced according to the principles of the circular economy. To achieve such ambitious goals, a form-stable, sustainable PCM was produced through vacuum impregnation. The form-stable PCM was produced starting from a low-toxicity, low-flammability polyethylene glycol of medium molecular weight (PEG 800), which was included in porous stone granules obtained as waste products of the cutting/processing of local (Lecce) stone. The thermal properties and thermal stability of PEG 800 and of its PCM-composite were evaluated by employing differential scanning calorimetry (DSC) and thermo-gravimetric analysis (TGA). The appropriate parameters to perform the impregnation procedure were identified through rheological and calorimetric analyses. A simple leakage test was performed to assess if the PEG polymer can leak from the stone flakes. Finally, the new PCM was added as an aggregate in aerial-lime-based mortars, and the mortar’s properties were analyzed in fresh (workability) and hardened (flexural and compressive strength and thermal characteristics) states for potential applications, particularly in ancient buildings.     

Efficacy of Liming Forest Soil in the Context of African Swine Fever Virus

Since September 2020, Germany has experienced the first ever outbreak of African swine fever (ASF). The first known cases occurred exclusively in wild boar in forest areas in Brandenburg and Saxony; in July 2021, infected domestic pigs were also confirmed for the first time. As wild boar are considered the main reservoir for the virus in the European region, an effective interruption of this infection chain is essential. In particular, the removal and safe disposal of infected carcasses and the direct disinfection of contaminated, unpaved ground are priorities in this regard. For the disinfection, highly potent as well as environmentally compatible disinfectants must be used, which are neither influenced in their effectiveness by the soil condition nor by increased organic contamination. Thus, in this study, slaked lime, milk of lime and quicklime (1% to 10% solutions) were selected for efficacy testing against the test virus recommended by the German Veterinary Society (DVG), Modified Vaccinia Ankara virus (MVAV), and ASF virus (ASFV) in conjunction with six different forest soils from Saxony in two different soil layers (top soil and mineral soil) each. In summary, 10% of any tested lime type is able to inactivate both MVAV and ASFV under conditions of high organic load and independent of the water content of the soil. At least a 4 log reduction of the virus titer in all tested forest soil types and layers and by all applied lime types was observed. In conclusion, the high efficacy and suitability of all tested lime products against both viruses and in the presence of high organic load in forest soil can be confirmed and will help to control ASF spread.