Biodegradable versus titanium osteosynthesis in maxillofacial traumatology: a systematic review with meta-analysis and trial sequential analysis

Titanium osteosynthesis is currently the fixation system of choice in maxillofacial traumatology. Biodegradable osteosynthesis systems have the ability to degrade in the human body. The aim of this study was to conduct a systematic review, with meta- and trial sequential analyses, to assess the efficacy and morbidity of biodegradable versus titanium osteosynthesis after maxillofacial trauma. MEDLINE, Embase, and CENTRAL were searched for randomized controlled trials and prospective and retrospective controlled studies. Five time periods were studied: perioperative, short-term (0–4 weeks), intermediate (6–12 weeks), long-term (>12 weeks), and overall follow-up. After screening 3542 records, 24 were included. All had a high risk of performance and detection bias due to the nature of the interventions. Meta-analysis showed no differences in efficacy or morbidity between biodegradable and titanium osteosynthesis. The risk of perioperative screw breakage was significantly higher (risk ratio 17.13, 95% confidence interval 2.19–34.18) and the symptomatic plate removal rate lower in the biodegradable group (risk ratio 0.11, 95% confidence interval 0.02–0.57), which was confirmed by the trial sequential analysis. The quality of evidence ranged from very low to moderate. Based on the narrative review and meta-analyses, current evidence shows that biodegradable osteosynthesis is a viable alternative to titanium osteosynthesis when applied in the treatment of maxillofacial trauma, with similar efficacy but significantly lower symptomatic plate removal rates. Perioperative screw breakage occurred significantly more often in the biodegradable group compared to the titanium group.     

A biological or a synthetic mesh in immediate breast reconstruction? A cohort-study of long-term Health related Quality of Life (HrQoL)

ObjectivesMeshes/matrices are commonly used in immediate breast reconstruction. There are few studies comparing biological and synthetic meshes and it is unknown what type of mesh gives the best long-term results. The aim of this study was to compare long-term health-related quality of life (HrQoL) and patient satisfaction in implant-based immediate breast reconstruction with a biological mesh (Surgisis®) with that of patients reconstructed with a synthetic mesh (TIGR ® Matrix Surgical Mesh).Material and methodsBoth cohorts were prospectively included and consecutively operated. Clinical data was collected. HrQoL was evaluated with EuroQoL-5 dimension – 3 levels questionnaire (EQ-5D-3L) and the Hospital Anxiety and Depression Scale (HADS) and the Breast-Q.Results and conclusionSeventy-one patients were operated on in the biological group and 49 in the synthetic group. The response rates were 75 and 84 per cent, respectively. Mean follow-up time was 74 months and 23 months, respectively. There were no statistical differences in satisfaction and quality of life between the two groups. Complications and radiation seem to lead to a lower satisfaction. Our findings could indicate that biological and synthetic meshes give an equal long-term result as regards patients’ perceived quality of life.     

Influence of Fine Grains on the Bending Fatigue Behavior of Two Implant Titanium Alloys

By means of the ultrasonic surface impact (amplitude of 30 μm, strike number of 48,000 times/mm²), nanograins have been achieved in the surfaces of both Ti6Al4V(TC4) and Ti3Zr2Sn3Mo25Nb(TLM) titanium alloys, mainly because of the dislocation motion. Many mechanical properties are improved, such as hardness, residual stress, and roughness. The rotating–bending fatigue limits of TC4 and TLM subjected to ultrasonic impact are improved by 13.1% and 23.7%, separately. Because of the bending fatigue behavior, which is sensitive to the surface condition, cracks usually initiate from the surface defects under high stress amplitude. By means of an ultrasonic impact tip with the size of 8 mm, most of the inner cracks present at the zone with a depth range of 100~250 μm in the high life region. The inner crack core to TC4 usually appears as a deformed long and narrow α-phase, while the cracks in TLM specimens prefer to initiate at the triple grain boundary junctions. This zone crosses the grain refined layer and the deformed coarse grain layer. With the gradient change of elastic parameters, the model shows an increase of normal stress at this zone. Combined with the loss of plasticity and toughness, it is easy to understand these fatigue behaviors.     

Hernias de la incisión de asistencia tras resección colorrectal laparoscópica. Influencia de la localización de la incisión y del uso de una malla profiláctica

Objectives

To determine the incidence of incisional hernia (IH) in the extraction incision (EI) in colorectal resection for cancer. To analyze whether the location of the incision has any relationship with the incidence of hernias and whether mesh could be useful for prevention in high-risk patients.

A Well-Balanced Positivity-Preserving Quasi-Lagrange Moving Mesh DG Method for the Shallow Water Equations

A high-order, well-balanced, positivity-preserving quasi-Lagrange moving mesh DG method is presented for the shallow water equations with non-flat bottom topography. The well-balance property is crucial to the ability of a scheme to simulate perturbation waves over the lake-at-rest steady state such as waves on a lake or tsunami waves in the deep ocean. The method combines a quasi-Lagrange moving mesh DG method, a hydrostatic reconstruction technique, and a change of unknown variables. The strategies in the use of slope limiting, positivity-preservation limiting, and change of variables to ensure the well-balance and positivity-preserving properties are discussed. Compared to rezoning-type methods, the current method treats mesh movement continuously in time and has the advantages that it does not need to interpolate flow variables from the old mesh to the new one and places no constraint for the choice of a update scheme for the bottom topography on the new mesh. A selection of one- and two-dimensional examples are presented to demonstrate the well-balance property, positivity preservation, and high-order accuracy of the method and its ability to adapt the mesh according to features in the flow and bottom topography.