Humoral immunity to Malassezia furfur serovars A, B and C in patients with pityriasis versicolor, seborrheic dermatitis and controls

Abstract This study examined the humoral immune responses to Malassezia furfur serovars A, B and C of 10 patients with pityriasis versicolor, 10 patients with seborrheic dermatitis and 20 age- and sex-matched controls. A transferable solid-phase ELISA was used to determine titres of total Igs, IgM, IgA and IgG specific to M. furfur serovars A, B and C. The results demonstrated that patients with seborrheic dermatitis had a significantly higher litre of total Igs to serovar A than patients with pityriasis versicolor; and that patients with seborrheic dermatitis had a significantly higher litre of IgA to serovar C than patients with pityriasis versicolor. The litres of total Igs for controls and patienls with seborrheic dermatitis were significantly lower to serovar B than to serovar C. A modified TSP ELISA was used to determine the titres of the IgG subclasses. Titres of IgG _1,3,4 to serovar B were significantly higher in seborrheic dermatitis patients than pityriasis versicolor patients and litres of IgG₃, to serovar A were significantly higher in seborrheic dermatitis patients than pityriasis versicolor patients. However, despite the differences between the patient groups, none of these results was significantly different to those of controls. Thus, this study did not demonstrate any differences in humoral immunity of patients suffering from Malassezia-associated dermatoses when compared to normal controls. These results may suggest that the humoral immune response to M. furfur is not related to the pathogenesis of Malassezia-associated dermatoses, but simply to the carriage of M. furfur on the skin.     

Low-artifact intravascular devices: MR imaging evaluation

Flow-phantom magnetic resonance (MR) imaging, with use of both spin-echo (SE) and gradient-echo (GRE) techniques at 1.5 T, was performed on the percutaneous Greenfield (beta-III titanium alloy [TMA wire]), Amplatz (MP32-N alloy), and Simon nitinol filters and TMA wire facsimiles of the bird's nest, Gunther, new retrievable, and Amplatz vena caval filters. SE imaging allowed detection of thrombi as small as 5 X 5 mm trapped within the percutaneous Greenfield, Simon nitinol, and TMA-wire facsimile filters; with the MP32-N Amplatz filter, a larger volume of thrombus (10 X 20-mm clots) was necessary for clot detection. GRE imaging allowed detection of intraluminal tilting of the percutaneous Greenfield and facsimile Amplatz (TMA-wire) filters. GRE imaging was useful for demonstrating postfilter turbulence due to clots, which was greatest for the Amplatz filter. Imaging of facsimile vascular devices made of tantalum or TMA wire did not cause the severe "black-hole" MR artifacts typical of the stainless-steel devices. SE and GRE imaging were very useful for determining caval patency in two patients with previously placed Mobin-Uddin filters. Noninvasive MR evaluation of blood vessels in the presence of a variety of low-artifact intravascular devices appears feasible.     

Long-term wear of ceramic matrix composite materials for hip prostheses under severe swing phase microseparation

The purpose of this study was to evaluate the long-term wear performance of alumina matrix composite (AMC) heads against alumina matrix composite inserts and alumina matrix composite heads against alumina (Al) inserts with the use of a hip-joint simulator incorporating severe swing phase joint microseparation. The wear of AMC on Al produced an average wear rate of 0.61 mm3/million cycles over the 5-million-cycle test duration. The wear of AMC on AMC produced an average wear rate of 0.16 mm3/million cycles over the 5-million-cycle test duration. Both the AMC on alumina and AMC on AMC produced significantly lower wear than previously tested HIPed alumina, where an average wear rate of 1.84 mm3/million cycles was reported over 5 million cycles. The wear mechanisms and wear debris of AMC on AMC and AMC on Al were similar to those observed in previous alumina retrieval studies with stripe wear caused by intragranular fracture and wear debris consisting of predominantly uniform 10-20-nm-sized particles and a few irregular particles up to 3 microm in size.     

Quantitative analysis of wear and wear debris from metal-on-metal hip prostheses tested in a physiological hip joint simulator

Osteolysis and loosening of artificial joints caused by UHMWPE wear debris has prompted renewed interest in metal-on-metal (MOM) hip prostheses. This study investigated the wear and wear debris morphology generated by MOM prostheses in a physiological anatomical hip simulator for different carbon content cobalt chrome alloys. The low carbon pairings demonstrated significantly higher "bedding in" and steady state wear rates than the mixed and high carbon pairings. The in vitro wear rates reported here were up to one or two orders of magnitude lower than the clinical wear rates for first-generation MOM hip prostheses. Two methods for characterising the metal wear debris were developed, involving digestion, scanning electron microscopy and transmission electron microscopy. The metal wear particles characterised by the two methods were similar in size, 25-36 nm, and comparable to particles isolated from periprosthetic tissues from first and second-generation MOM hip prostheses. Due to the small size of the metal particles, the number of particles generated per year for MOM prostheses in vitro was estimated to be up to 100 times higher than the number of polyethylene particles generated per year in vivo. The volumetric wear rates were affected by the carbon content of the cobalt chrome alloy and the material combinations used. However, particle size and morphology was not affected by method of particle characterisation, the carbon content of the alloy or material combination.