Gangliosides of cultured astroglia

Cultured astrocytes prepared from newborn rat brain and 13-day-old chick embryonic brain were analyzed qualitatively and quantitatively for ganglioside content. All preparations contained approximately the same total level: 2.4-3.4 micrograms N-acetylneuraminic acid (NeuAc)/mg protein. In contrast, the value for primary cultures of neurons from chick embryonic brain was 5.9. The non-hexosamine-containing species, GM3 and GD3, comprised 75-85% of the total in astroglial cultures, the remainder consisting mainly of structural types other than the gangliotetraose series; choleragenoid assay revealed the latter to be virtually absent or to comprise at most a few percent. Deficiency of gangliotetraose synthesizing ability was indicated by the very low level of UDP-GalNac:GM3 N-acetylgalactosaminyltransferase detected in the cells. Treatment of cultured astrocytes with astroglial growth factor 2 or dibutyryl cyclic AMP caused little if any change in quantity or pattern of gangliosides. The large majority of cells stained in a manner characteristic of astrocytes: positive for glial fibrillary acidic protein, negative for galactosyl ceramides. Staining with cholera toxin and anti-GM1 antibody was essentially negative, as was that with tetanus toxin, A2B5 monoclonal antibody, and antibody to GD3. All evidence thus points to cultured astrocytes of rat and chick brain containing appreciable gangliosides, most of which are GM3 and GD3 with the majority of the remainder comprising structures other than the gangliotetraose type.     

Anterior segment findings in AIDS patients with cytomegalovirus retinitis

Background: Anterior segment findings in AIDS patients presenting with cytomegalovirus (CMV) retinitis have not been specifically addressed in the American literature. Methods: Our study evaluated 21 AIDS patients with CMV retinitis. Results: Nineteen (90%) of these patients exhibited corneal endothelial deposits concurrent with CMV retinitis. The endothelial deposits were microscopic, opaque, linear flecks arranged in a reticular-like fashion. Of 42 eyes evaluated, 32 (76%) demonstrated active CMV retinitis. Corneal endothelial deposits were noted in 26 (81%) of the 32 eyes with retinitis. These corneal endothelial deposits were absent in the eyes which did not have CMV retinitis. Conclusion: Meticulous examination of the retina of an HIV-positive or AIDS patient who presents with reticularly arranged, linear, flecked corneal endothelial deposits should be performed to ensure that the diagnosis of CMV retinitis can be ruled out.     

Systematic review of the application of virtual reality to improve balance,gait and motor function in patients with Parkinson’s disease

Background:Virtual reality (VR) is an advanced technique used in physical rehabilitation of neurological disorders, however the effects of VR on balance, gait, and motor function in people with Parkinson’s (PD) are still debated. Therefore, the systematic review aimed to determine the role of VR on motor function, balance and gait in PD patients.Methods:A comprehensive search to identify similar randomised controlled trials was conducted targeting 5 databases including Web of Science, PubMed, CINHAL, Cochrane Library, and Physiotherapy Evidence Database. A total of 25 studies were found eligible for this systematic review, and the methodological assessment of the quality rating of the studies was accomplished using the physiotherapy evidence database scale by 2 authors.Results:Out of the 25 included studies, 14 studies reported on balance as the primary outcome, 9 studies were conducted to assess motor function, and 12 assessed gait as the primary outcome. Most studies used the Unified Parkinson disease rating scale UPDRS (part-III) for evaluating motor function and the Berg Balance Scale as primary outcome measure for assessing balance. A total of 24 trials were conducted in clinical settings, and only 1 study was home-based VR trainings. Out of 9 studies on motor function, 6 reported equal improvement of motor function as compared to other groups. In addition, VR groups also revealed superior results in improving static balance among patient with PD.Conclusion:This systemic review found that the use of VR resulted in substantial improvements in balance, gait, and motor skills in patients with PD when compared to traditional physical therapy exercises or in combination with treatments other than physical therapy. Moreover, VR can be used as a supportive method for physical rehabilitation in patients of PD. However, the majority of published studies were of fair and good quality, suggesting a demand for high quality research in this area.     

Mentha: A genus rich in vital nutra‐pharmaceuticals—A review

The genus Mentha comprises several aromatic species, which are cultivated world‐over due to their distinct aroma and commercial value. In addition to traditional food flavoring uses, Mentha are well recognized for their folk medicinal uses, especially to treat cold, fever, and digestive and cardiovascular disorders. A number of biological activities such as antioxidant, antimicrobial, biopesticidal, antitumor, anticancer, antiviral, antiallergic, antiinflammatory, antihypertensive, and urease inhibitory activity have been ascribed to Mentha. The traditional pharmacological attributes of Mentha herbs can be linked to the occurrence of bioactive phytochemicals such as terpenoids, alcohols, rosmarinic acid, and antioxidant phenolics among others. A rich source of bioactives, different species of Mentha, can be explored as a promising candidate for the development of nutra‐pharmaceuticals. This review covers the nutritional, phytochemical, and traditional medicinal aspects and multiple biological activities of some commonly available species of Mentha so as to explore their potential applications for nutra‐pharmaceutical and cosmo‐nutraceutical industry. Detailed chemical profile and pharmaceutical attributes of various Mentha essential oils are also covered. Moreover, based on computational analysis, quantitative chemical component–antioxidant activity relationship model is reviewed to predict and correlate structure–activity relationship of potential bioactives in selected Mentha essential oils leading to discovery and developmenmt of novel natural drugs.     

Fabrication of a graphene-based sensor to detect the humidity and the temperature of a metal body with imprecise data analysis

Graphene is a 2D material with remarkable properties. The present study demonstrates the fabrication of a graphene-based sensor for measuring the temperature and humidity of a metal body. The graphene sensor was fabricated by depositing a thin film of graphene nanoparticles between silver electrodes (separated by ∼50 μm) on a glass substrate. The graphene thin film was characterized by XRD, Raman spectroscopy and UV-vis techniques. The capacitance and resistance for both the relative humidity (in the range of 0–100% RH) and temperature (in the range of 230–310 K) were measured using an LCR meter at 1 kHz in a controlled chamber. The graphene-based sensor expressed high sensitivity with fast response and recovery times for both humidity and temperature with long stability and low hysteresis curves. The sensor was also tested on a metal body, which expressed a good response time. Moreover, the measured data of capacitance and resistance was analyzed with classical and neutrosophic analysis as an application of modern material statistics. It was observed that neutrosophic analysis is more flexible for analyzing the capacitance and resistance of the fabricated sensor.

Graphene is a 2D material with remarkable properties.     

Prediction of Compressive Strength of Sustainable Foam Concrete Using Individual and Ensemble Machine Learning Approaches

The entraining and distribution of air voids in the concrete matrix is a complex process that makes the mechanical properties of lightweight foamed concrete (LFC) highly unpredictable. To study the complex nature of aerated concrete, a reliable and robust prediction model is required, employing different machine learning (ML) techniques. This study aims to predict the compressive strength of LFC by using a support vector machine (SVM) as an individual learner along with bagging, boosting, and random forest (RF) as a modified ensemble learner. For that purpose, a database of 191 data points was collected from published literature, where the mix design ingredients, i.e., cement content, sand content, water to cement ratio, and foam volume, were chosen to predict the compressive strength of LFC. The 10-K fold cross-validation method and different statistical error and regression tools, i.e., mean absolute error (MAE), root means square error (RMSE), and coefficient of determinant (R²), were used to evaluate the performance of the developed ML models. The modified ensemble learner (RF) outperforms all models by yielding a strong correlation of R² = 0.96 along with the lowest statistical error values of MAE = 1.84 MPa and RMSE = 2.52 MPa. Overall, the result suggests that the ensemble learners would significantly enhance the performance and robustness of ML models.     

Optimization-Based Economical Flexural Design of Singly Reinforced Concrete Beams: A Parametric Study

In the past, many studies have been conducted on the optimization of reinforced concrete (RC) structures. These studies have demonstrated the effectiveness of different optimization techniques to obtain an economical design. However, the use of optimization techniques to an obtain economical design is not so practical due to the difficulty in applying most of the optimization techniques to achieve an optimal solution. The RC beam is one of the most common structural elements encountered by a practising design engineer. The current study is designed to highlight the potential of the Solver tool in MS Excel as an easy-to-use option for optimizing the design of simply supported RC beams. A user-friendly interface was developed in a spreadsheet in which beam design parameters from a typical design can be entered and an economical design can be obtained using the Evolutionary Algorithm available in the MS Excel Solver tool. To demonstrate the effectiveness of the developed optimization tool, three examples obtained from the literature have been optimized. The results showed that up to 24% economical solution can be obtained by keeping the same material strengths that were assumed in the original design. However, if material strength is also considered as a variable, up to 44% of the economical solution can be obtained. A parametric study was also conducted to investigate the effect of different design variables on the economical design of simply supported RC beams and to derive useful rules of thumb for their design and proportioning, with the objective of cost minimization. The results of the parametric study suggest that the grade of the reinforcing steel is one of the most influential factors that affect the cost of simply supported RC beams. Practicing engineers can use the trends derived from this research to further refine their optimal designs.     

Controlling the Wettability of ZnO Thin Films by Spray Pyrolysis for Photocatalytic Applications

Herein, we synthesized the zinc oxide (ZnO) thin films (TFs) deposited on glass substrates via spray pyrolysis (SP) to prepare self-cleaning glass. Various process parameters were used to optimize photocatalytic performance. Substrates were coated at room temperature (RT) and 250 °C with a 1 mL or 2 mL ZnO solution while maintaining a distance from the spray gun to the substrate of 20 cm or 30 cm. Several characterization techniques, i.e., XRD, SEM, AFM, and UV–Vis were used to determine the structural, morphological, and optical characteristics of the prepared samples. The wettability of the samples was evaluated using contact angle measurements. As ZnO is hydrophilic in nature, the RT deposited samples showed a hydrophilic character, whereas the ZnO TFs deposited at 250 °C demonstrated a hydrophobic character. The XRD results showed a higher degree of crystallinity for samples deposited on heated substrates. Because of this higher crystallinity, the surface energy decreased, and the contact angle increased. Moreover, by using 2 mL solution, better surface coverage and roughness were obtained for the ZnO TFs. However, by exploiting the distance of the spray to the samples size distribution and surface coverage can be controlled, the samples deposited at 30 mL showed a uniform particle size distribution from 30–40 nm. In addition, the photoactivity of the samples was tested by the degradation of rhodamine B dye. Substrates prepared with a 2 mL solution sprayed at 20 cm showed higher dye degradation than other samples, which can play a vital role in self-cleaning. Hence, by changing the said parameters, the ZnO thin film properties on glass substrates were optimized for self-cleaning diversity.