Patellofemoral joint: kinematic MR imaging to assess tracking abnormalities

The patellofemoral joint was imaged with magnetic resonance (MR) in the axial plane while the knee was positioned from 0 degrees to 32 degrees of flexion (nine positions). These multiple sequential images obtained within the early phases of flexion of the knee were viewed in a "cine-loop" format, producing a kinematic study that clearly demonstrated the relationship of the patella to the trochlear groove. Four healthy subjects and one patient with known bilateral subluxing patellae were studied. The preliminary results suggest that kinematic MR imaging of the patellofemoral joint is potentially useful for the evaluation of patellar tracking abnormalities.     

Photodynamic therapy for the treatment of metastatic lesions in bone: studies in rat and porcine models

This study represents the first reported use of photodynamic therapy (PDT) for metastatic bone lesions and specifically, as a treatment for spinal metastases. A model of bone metastasis in rat confirmed the efficacy of benzoporphyrin derivative-monoacid-mediated PDT for treating lesions within the spine and appendicular bone. Fluorimetry confirmed the selective accumulation of drug into the tumor(s) at 3 h post-injection. 48 h post-light delivery into the vertebral body of the rat spine loss of bioluminescent signal and histological analyses of sectioned spine confirmed MT-1 tumor cell kill in vivo as previously confirmed in vitro using an established cell viability assay. Porcine vertebrae provided a model comparable to that of human for light propagation and PDT response. Histological examination of vertebrae 48 h post-PDT revealed a necrotic radius of 0.6 cm with an average fluence rate of 4.3 mW/cm2. Non-necrotic tissue damage was evident up to 2 cm out from the treatment fiber. Results support the application of PDT to the treatment of primary or metastatic lesions within bone.     

Strategies to improve the signal and noise performance of active matrix, flat-panel imagers for diagnostic x-ray applications

A theoretical investigation of factors limiting the detective quantum efficiency (DQE) of active matrix flat-panel imagers (AMFPIs), and of methods to overcome these limitations, is reported. At the higher exposure levels associated with radiography, the present generation of AMFPIs is capable of exhibiting DQE performance equivalent, or superior, to that of existing film-screen and computed radiography systems. However, at exposure levels commonly encountered in fluoroscopy, AMFPIs exhibit significantly reduced DQE and this problem is accentuated at higher spatial frequencies. The problem applies both to AMFPIs that rely on indirect detection as well as direct detection of the incident radiation. This reduced performance derives from the relatively large magnitude of the square of the total additive noise compared to the system gain for existing AMFPIs. In order to circumvent these restrictions, a variety of strategies to decrease additive noise and enhance system gain are proposed. Additive noise could be reduced through improved preamplifier, pixel and array design, including the incorporation of compensation lines to sample external line noise. System gain could be enhanced through the use of continuous photodiodes, pixel amplifiers, or higher gain x-ray converters such as lead iodide. The feasibility of these and other strategies is discussed and potential improvements to DQE performance are quantified through a theoretical investigation of a variety of hypothetical 200 microm pitch designs. At low exposures, such improvements could greatly increase the magnitude of the low spatial frequency component of the DQE, rendering it practically independent of exposure while simultaneously reducing the falloff in DQE at higher spatial frequencies. Furthermore, such noise reduction and gain enhancement could lead to the development of AMFPIs with high DQE performance which are capable of providing both high resolution radiographic images, at approximately 100 microm pixel resolution, as well as variable resolution fluoroscopic images at 30 fps.     

Cone-beam computed tomography with a flat-panel imager: initial performance characterization

The development and performance of a system for x-ray cone-beam computed tomography (CBCT) using an indirect-detection flat-panel imager (FPI) is presented. Developed as a bench-top prototype for initial investigation of FPI-based CBCT for bone and soft-tissue localization in radiotherapy, the system provides fully three-dimensional volumetric image data from projections acquired during a single rotation. The system employs a 512 x 512 active matrix of a-Si:H thin-film transistors and photodiodes in combination with a luminescent phosphor. Tomographic imaging performance is quantified in terms of response uniformity, response linearity, voxel noise, noise-power spectrum (NPS), and modulation transfer function (MTF), each in comparison to the performance measured on a conventional CT scanner. For the geometry employed and the objects considered, response is uniform to within 2% and linear within 1%. Voxel noise, at a level of approximately 20 HU, is comparable to the conventional CT scanner. NPS and MTF results highlight the frequency-dependent transfer characteristics, confirming that the CBCT system can provide high spatial resolution and does not suffer greatly from additive noise levels. For larger objects and/or low exposures, additive noise levels must be reduced to maintain high performance. Imaging studies of a low-contrast phantom and a small animal (a euthanized rat) qualitatively demonstrate excellent soft-tissue visibility and high spatial resolution. Image quality appears comparable or superior to that of the conventional scanner. These quantitative and qualitative results clearly demonstrate the potential of CBCT systems based upon flat-panel imagers. Advances in FPI technology (e.g., improved x-ray converters and enhanced electronics) are anticipated to allow high-performance FPI-based CBCT for medical imaging. General and specific requirements of kilovoltage CBCT systems are discussed, and the applicability of FPI-based CBCT systems to tomographic localization and image-guidance for radiotherapy is considered.     

Cone-beam computed tomography with a flat-panel imager: effects of image lag

A system for cone-beam computed tomography (CBCT) has been developed based upon the technology of active matrix flat-panel imagers (FPIs), and the system has demonstrated the potential for fully three-dimensional volumetric imaging with high spatial and contrast resolution. This paper investigates the effects of image lag (arising from charge trapping and release in the FPI pixels) upon CBCT reconstructions. Hypotheses were derived based upon a simple, geometrical/physical model, suggesting that image lag in the projection data results primarily in two artifacts: a spatial blurring artifact in the direction opposite to the direction of rotation (called a "comet") and a line artifact along the direction of the first few projections (called a "streak"). The hypotheses were tested by means of computer simulations and experimental measurements that yielded CBCT images of a simple cylindrical water phantom containing an attenuating rod of varying size and composition. The computer simulations generated projection images based upon analysis of the system geometry and a simple model of the FPI that allowed free adjustment of the image lag. Experimental measurements involved CBCT scans of the phantom under various conditions and modes of acquisition followed by examination of the resulting CBCT axial slices for lag artifacts. Measurements were performed as a function of exposure level, position and contrast of the rod, and for three modes of acquisition designed to isolate and/or minimize the two hypothesized artifacts. The results clearly illustrate the comet and streak artifacts, particularly in relation to high-contrast objects imaged at high exposure levels. The significance of such artifacts under clinical conditions is expected to be small, considering the magnitude of the effect relative to the morphology and composition of typical anatomy. The artifacts may become appreciable, however, in the presence of high-contrast objects, such as marker BBs, dental fillings, and metal prosthetics. A procedural method of reducing lag artifacts is demonstrated.     

Marrow regeneration after mechanical depletion

The origin of marrow regeneration after mechanical depletion was reinvestigated in mouse chimeras. The results were compatible with the local origin of stem cells from remnants of incompletely removed marrow, but not with their origin from a common precursor of both bone and hemopoietic cell lines. In transplanted femurs depleted by a modified technique of in vivo evacuation of marrow, hemopoietic regeneration failed to occur. The presence of hemopoietic stem cells in the Haversian canals was thus excluded. The demonstration of ample hemopoiesis with minimal bone formation in nondepleted controls in which bone marrow initially became necrotic provided new evidence that osteogenesis was not a prerequisite of hemopoietic regeneration.     

Severe malabsorption in autoimmune polyendocrinopathy-candidosis-ectodermal dystrophy syndrome successfully treated with immunosuppression

A 15 year old boy with autoimmune polyendocrinopathy-candidosis-ectodermal dystrophy syndrome suffered recurrent episodes of severe intractable diarrhoea, steatorrhoea, and hypocalcaemia. The only treatment modality, which controlled the malabsorption syndrome, was immunosuppression with intravenous high dose methylprednisolone and oral methotrexate maintenance therapy.