Central illustration: cumulative major adverse cardiac events (MACE) and bioresorbable vascular scaffold (BVS) thrombosis rates after 1, 2, 3, 4 and 5 years.相似文献
Success of meniscal repair with early or immediate motion depends on the ability of the suture fixation to withstand the loads applied. Vertical and horizontal mattress suture techniques were tested using 2-0 Ethibond, and 0-PDS and 1-PDS sutures (Ethicon, Somerville, NJ). Mulberry knot technique was tested with 0-PDS and 1-PDS sutures. Twenty menisci (60 sutures) were tested for each suture material. Sutures were placed 3 to 4 mm from the peripheral edge of the meniscus with double barreled cannulas for vertical and horizontal mattress techniques or a spinal needle for the mulberry knot technique, reproducing clinical techniques of meniscal repair. Mechanical testing of suture fixation was performed to failure at a rate of 10 mm/min on a MTS material testing system (MTS Systems Corp. Minneapolis, MN). Suture pullouts were reported as the load displacement to failure from the inner fragment only, because clinical failure would ensue should a suture pull through the inner fragment of a tear. Vertical mattress technique with 1-PDS suture had significantly greater load to failure than any other combination (P < .05). Analysis of variance showed that the vertical mattress technique had statistically superior pullout strength (P < .0001) compared with the horizontal mattress and mulberry knot techniques, which were statistically similar. There were significant differences (P < .0001) between suture types, with 1-PDS proving best compared with 0-PDS, which was stronger than 2-0 Ethibond. Selection of suture material had the greatest impact on vertical mattress load to failure and was not important to the strength of the other techniques. 相似文献
A case of meniscal ossicles occurring in the left knee of a 23-year-old woman is presented. Radiographs showed two calcified
lesions at the posteromedial aspect of the knee which were interpreted as loose bodies. Sonography, computed tomography arthrography
and magnetic resonance imaging showed the fragments within the posterior horn of the medial meniscus permitting a diagnosis
of meniscal ossicles. These techniques can detect meniscal ossicles and exclude intra-articular loose bodies.
Received: 7 February 2000 Revision requested: 14 March 2000 Revision received: 18 April 2000 Accepted: 24 April 2000 相似文献
BackgroundIt remains unknown how biomechanics change in posterior lateral knee using different fixation techniques in lateral meniscal allograft transplantation (MAT) during simulated toe-touch partial weight-bearing. This study aimed to compare the biomechanical effects on posterior knee between bridge and bone plug fixation in lateral MAT.MethodsIntact knee, bone bridge fixation, and bone plug fixation were tested with 500 N of axial load during knee flexion at 0°, 30°, and 60°, which simulated toe-touch partial weight-bearing. Contact area and peak pressure were assessed on posterior knee and the shift of peak pressure position were measured.ResultsOn the posterior lateral compartment, the contact mechanics of bone bridge fixation were similar to those of the intact knee (all P-values > 0.05), but its peak pressure was higher than that of intact knee at 60° (P = 0.002). For bone plug fixation, the contact area of the posterior lateral knee was significantly lower than those of intact knee and bone bridge fixation at 30° and 60° (all P-values < 0.05). The peak pressure of the posterior lateral knee was higher than that of the intact knee at all flexions and higher than that of bone bridge fixation at 30° and 60° (all P-values < 0.05). The peak pressure position of bone plug fixation shifted more laterally and posteriorly compared with intact knee and bone bridge fixation during knee flexion.ConclusionBone bridges could maintain posterior knee biomechanics better than bone plug fixation during knee bending during partial weight-bearing. 相似文献
The preservation of meniscal tissue is paramount for long-term joint function, especially in younger patients who are athletically active. Many studies have reported encouraging results following the repair of meniscus tears, including both simple longitudinal tears located in the periphery and complex multiplanar tears that extend into the central third avascular region. However, most types of meniscal lesions are managed with a partial meniscectomy. Options to restore the meniscus range from an allograft transplantation to the use of synthetic and biological technologies. Recent studies have demonstrated good long-term outcomes with meniscal allograft transplantation, although the indications and techniques continue to evolve, and the long-term chondroprotective potential of this approach has yet to be determined. Several synthetic implants, most of which are approved in the European market, have shown some promise for replacing part of or the entire meniscus, including collagen meniscal implants, hydrogels, and polymer scaffolds. Currently, there is no ideal implant generated by means of tissue engineering. However, meniscus tissue engineering is a fast developing field that promises to develop an implant that mimics the histologic and biomechanical properties of a native meniscus. 相似文献
BackgroundSelection of the transcatheter heart valve size for a mitral valve-in-valve procedure is based on the type and manufacturer’s labelled size. However, accurate information of surgical heart valve (SHV) size may not be available in the patient’s medical record. The purpose of this study is to establish reference data for computed tomography (CT) dimensions of commonly used mitral SHV in order to determine the manufacturer’s labelled size from a cardiac CT data set.MethodsCT datasets of 105 patients with surgical mitral bioprosthesis and available manufacturer labeled datasets were included in the analysis. CT derived valve dimensions were assessed by two observers using multiplanar reformats aligned with the basal sewing ring. A circular region of interest was used in a standardized fashion to minimize influence of image acquisition and reconstruction parameters. Interobserver variability was assessed by Bland-Altman analysis.ResultsThe CT-derived dimensions were stratified by valve size and type, and SHV properties were demonstrated for 5 common valve types. Variability of measurements was small and inter-observer limits of agreement were narrow. Stratified by SHV type, no overlap was noted for CT-derived dimensions among different SHV sizes . A reference table of CT characteristics of surgical mitral bioprosthesis types was created.ConclusionThe study provides reference CT data for determining the manufacturers’ labeled SHV size across a range of commonly used mitral SHVs. The findings will be important to help identify types of surgical mitral bioprosthesis utilizing CT characteristics for patients without SHV size documentation. 相似文献