Study on the Mechanical Properties,Wear Resistance and Microstructure of Hybrid Fiber-Reinforced Mortar Containing High Volume of Industrial Solid Waste Mineral Admixture

The use of a high volume of industrial solid waste mineral admixture and hybrid fiber can greatly reduce the amount of cement in mortar or concrete, improve its performance, ensure the service properties of mortar or concrete, and reuse industrial solid waste to reduce the environmental burden, which has significant research significance. In this paper, the mechanical properties, wear resistance and microstructure of hybrid fiber-reinforced mortar (HFRM) with a high content of industrial solid waste mineral admixture were systematically studied under different water/binder ratios. Mineral admixtures include fly ash, silica fume and granulated blast furnace slag (slag). The total content of hybrid glass fiber (GF) and polypropylene fiber (PPF) was 2% by volume fractions, and six different water/binder ratios ranging from 0.27 to 0.62 were used. The following conclusions were drawn: fibers have a significant negative effect on the properties of mortars with a low water/binder ratio (w/b = 0.27) and high content of mineral admixtures. In general, the effect of adding hybrid fiber on improving the wear resistance of mortar is more obvious. The average residual weight of hybrid fiber-reinforced mortar is the highest after the wear resistance test. Comprehensively considering the compressive strength, flexural strength, wear resistance and microstructure of the mortar samples, G8PP2-0.40 is the optimal mix ratio. At this time, the replacement rates of fly ash, silica fume and slag are: 20%, 5% and 30%, the water/binder ratio is 0.40, and the content of GF and PPF is 1.6% and 0.4%, respectively.     

Performance and Cost-Effectiveness of Short Pitch-Based Carbon Fiber Reinforced Mortar Composite

This paper discusses the performance of the short pitch-based carbon fiber reinforced mortar (CFRM) composite considering its key properties and cost-effectiveness. Five different types of mortar composite were produced using 0–4% volume contents of short pitch-based carbon fibers. The mortar composites were tested for inverted slump cone flow (flow time and volume flow), unit weight, air content, compressive strength, flexural strength, impact resistance, and water absorption. The cost-effectiveness of CFRM was assessed based on the performance to cost ratio (PCR), which was calculated for each mortar composite, considering its workability, mechanical properties, and durability. The inverted slump cone volume flow was counted as a measure of workability, whereas the compressive strength, flexural strength, and impact resistance were considered as the major attributes of the mechanical behavior. In addition, the water absorption was used as a measure of durability. The test results revealed that the mortar composite made with 3% carbon fibers provided adequate workability, a relatively high unit weight and low air content, the highest compressive strength, excellent flexural strength, good impact resistance, and the lowest water absorption. It was also found that the PCR increased up to 3% carbon fibers. Beyond a 3% fiber content, the PCR significantly decreased. The overall research findings revealed that the mortar with 3% carbon fibers was the optimum and most cost-effective mortar composite.     

The Influence of Incinerated Sewage Sludge as an Aggregate on the Selected Properties of Cement Mortars

In line with the trend of using waste raw materials in the technology of building materials, experimental studies of cement mortars containing various amounts of fine-grained waste aggregate were carried out. The waste aggregate was based on an incinerated municipal sewage sludge which was mechanically crushed to an appropriate grading. Chemical and physical properties of the waste aggregate are presented. Mortars with varying amounts of waste aggregate as a replacement for natural sand were prepared. Study determines compressive strength and flexural strength up to 56 days. Properties such as capillary action, air content and thermal conductivity were determined. The results of the tests has shown that the incinerated waste sludge can be used as a partial or total replacement for natural aggregate. In mortars with waste aggregate, a favorable relation between flexural and compressive strengths was observed, which translates into increased strength of the interfacial transition zone. A significant increase in water absorption was observed for mortars containing high amounts of waste aggregate, which is directly related to its porous structure. Conducted studied prove that the aggregate obtained from incineration of the municipal sewage sludge can a feasible alternative for natural aggregates in production of masonry and rendering mortars for construction purposes.     

Durability of a New Thermal Aerogel-Based Rendering System under Distinct Accelerated Aging Conditions

The widespread application of innovative thermal enhanced façade solutions requires an adequate durability evaluation. The present work intends to assess the durability of a new aerogel cement-based rendering system through the adaptation of different accelerated aging cycles, such as heating–freezing, freeze–thawing, and heat–cold. Several mechanical properties and also capillary and liquid water absorptions were tested for uncoated and coated specimens. A decrease in the mechanical strength, especially after freeze–thaw cycles, was observed. However, the water action promoted the late hydration of the cement paste contributing to the densification of the matrix and, consequently, the increase of the adhesive strength. Additionally, a decrease in the dynamic modulus of elasticity and an increase in the Poisson’s ratio were observed after aging, which indicates a higher capacity of the render to adapt to substrate movements, contributing to a reduction of cracking.     

New Composite Material for Masonry Repair: Mortar Formulations and Experimental Studies

The need for retrofitting existing masonry structures is progressively becoming more important due to their continuous deterioration or need to meet the current design requirements of Eurocodes. Textile-Reinforced Mortar (TRM) composite systems have emerged as a sustainable repair methodology suitable for structure retrofitting. Nevertheless, their mechanical performance is still far from being fully investigated. This paper presents an experimental study on the tensile and bond behaviors of a new mortar-based composite consisting of mineral additives, blended cement mortar, and stainless-steel grid. Three different mineral additives (silica fume, fly ash, and blast furnace slag), in binary and ternary systems were used. The experimental study included uniaxial tensile coupon testing on composite specimens and bond tests on composite material applied to clay-brick substrate. The results obtained with the different textile-reinforced cement-based mortars were compared and are discussed here. It was found that, for mortar formulations containing mineral additives—such as fly ash or blast-furnace slag—with high tensile and bond strengths, an adequate adherence between the constituents was obtained. The developed mortar presents mechanical performances equivalent to traditional mortars without additives. The study contributes to the existing knowledge regarding the structural behavior of TRM and promotes the development of a low impact carbon cementitious matrix.     

Asphalt-Cement Concretes with Reclaimed Asphalt Pavement and Rubber Powder from Recycled Tire

The goal of the work was to describe properties of asphalt-cement concrete (ACC) with reclaimed asphalt pavement (RAP), Portland cement, sand, and rubber powder (RP), as a material to base courses of road pavements. The mixtures were designed with the RAP in the amount of 75, 80, and 85% (m/m) and chosen cement-sand-rubber (CSR) mortar. Three CSR mortars were composed with cement CEM 42.5 R in the amount 29% (m/m); washed sand 0/2 mm in the amount 29, 35, or 41%; rubber powder of granulation 0/1 mm in the amount of 18, 24, or 29% (m/m); and water in the amount 12% fulfilled w/c = 0.4. The optimum moisture content of the selected ACC with CSR mortar determined in the modified Proctor compaction test was approximately 6% and maximum dry density 2.000 g/cm³. Laboratory tests of indirect tensile strength, stiffness modulus (IT-CY and 4PB-PR), water resistance, fatigue life, and complex modulus (E*) at different temperatures were conducted and analyzed. The test results are presented, among others, in the form: the isotherm of complex modulus, Black curve, the master curve, and the Cole-Cole plot.     

Influence of Natural Weather Conditions in the Long-Term Fracture Energy of Glass Fibre Reinforced Cement (GRC) Modified with Chemical Additions

The use of glass fibre-reinforced cement (GRC) in structural elements has been limited due to the reduction in the mechanical properties of the material with aging. Chemical additions have been used to modify the cement mortar formulation in order to minimise such loss, but no conclusive results have been obtained yet. Moreover, the application of accelerated aging methods in such modified GRC formulations still poses several uncertainties. An experimental campaign seeking to assess the reduction in the fracture energy of two GRCs manufactured with modified matrixes after five years of exposure to natural environment was performed. Furthermore, a comparison with results from the literature that used accelerated aging methods was performed. The results show that the use of the chemical additives might be capable of maintaining to a notable extent the mechanical properties of GRC after five years of natural aging. Regarding the accelerated aging method by means of immersion in hot water tanks, it seemed that the equivalences applied in previous research accurately match the degradation of the material after natural exposure to weather. Additionally, a digital image correlation analysis showed that aged GRCs seemed to distribute damage in a smaller area than young GRCs.     

Modified Carboxymethylcellulose-Based Scaffolds as New Potential Ecofriendly Superplasticizers with a Retardant Effect for Mortar: From the Synthesis to the Application

This article is focused on the research and development of new cellulose ether derivatives as innovative superplasticizers for mortar systems. Several synthetic strategies have been pursued to obtain new compounds to study their properties on cementitious systems as new bio-based additives. The new water-soluble admixtures were synthesized using a complex carboxymethylcellulose-based backbone that was first hydrolyzed and then sulfo-ethylated in the presence of sodium vinyl sulphonate. Starting with a complex biopolymer that is widely known as a thickening agent was very challenging. Only by varying the hydrolysis times and temperatures of the reactions was achieved the aimed goal. The obtained derivatives showed different molecular weight (Mw) and anionic charges on their backbones. An improvement in shear stress and dynamic viscosity values of CEM II 42.5R cement was observed with the samples obtained with a longer time of higher temperature hydrolysis and sulfo-ethylation. Investigations into the chemical nature of the pore solution, calorimetric studies and adsorption experiments clearly showed the ability of carboxymethyl cellulose superplasticizer (CMC SP) to interact with cement grains and influence hydration processes within a 48-h time window, causing a delay in hydration reactions in the samples. The fluidity of the cementitious matrices was ascertained through slump test and preliminary studies of mechanical and flexural strength of the hardened mortar formulated with the new ecological additives yielded values in terms of mechanical properties. Finally, the computed tomography (CT) images completed the investigation of the pore network structure of hardened specimens, highlighting their promising structure porosity.     

Construction of Discrete Element Constitutive Relationship and Simulation of Fracture Performance of Quasi-Brittle Materials

In order to solve the problem that the built-in parallel bond model in the discrete element software cannot adequately simulate the post-peak fracture behavior of quasi-brittle materials, a linear cohesive model was established. First, two particles are used to simulate the interface constitutive behavior in different modes. The results show that the new model can better simulate the behavior of Mode-I fracture, Mode-II fracture, and Mixed-mode fracture. Then, the influence of micro-parameters on the newly constructed constitutive model is analyzed, which provides a basis for the determination of micro-parameter values. Finally, the proposed softening model is applied to a three-point bending test of mortar, and the fracture behavior obtained is compared to the acoustic emission results. The simulation results also show that the constitutive model we built can be used to simulate the fracture behavior of quasi-brittle materials such as mortar and concrete.     

Flexural and Impact Behaviors of Mortar Composite Including Carbon Fibers

This study investigated the flexural and impact performances of mortar composite made with carbon fibers (MCCF). Four mortar composites (MCCF1, MCCF2, MCCF3, and MCCF4) were produced, using 1%, 2%, 3%, and 4% carbon fibers by volume, respectively. Another mortar composite without any carbon fibers (MCCF0) was prepared for its use as a control mix. The freshly mixed mortar composites were tested for inverted slump cone flow time to ensure they had an adequate workability to cast test specimens under vibration. In addition, all fresh mortar composites were examined for density and air content. The hardened mortar composites were tested for their first-crack flexural strength, ultimate flexural strength, first-crack impact resistance, and ultimate impact resistance. Moreover, the first-crack flexural toughness, ultimate flexural toughness, first-crack impact toughness, and ultimate impact toughness were determined for all hardened mortar composites. The correlations among the hardened properties of the mortar composites were also sought. Finally, the optimum fiber content was defined from the overall test results and considering the costs of the mortar composites. The test results showed that the workability and density of the fresh mortar composite decreased, whereas its air content increased due to the inclusion of carbon fibers. However, MCCF3 possessed the highest density and lowest air content among all MCCF mixes. It also had a higher workability than MCCF4. In the hardened state, the first-crack flexural strength and impact resistance, as well as the ultimate flexural strength and impact resistance of mortar composite, increased significantly with the increasing volume content of carbon fibers. In addition, the first-crack flexural toughness, ultimate flexural toughness, first-crack impact toughness, and ultimate impact toughness increased greatly with the higher volume content of carbon fibers. Strong correlations between the flexural strength and impact resistance, and between the flexural toughness and impact toughness of the mortar composites, were observed. Above all, excellent flexural strength, flexural toughness, impact resistance, and impact toughness values were observed for MCCF4 (4% carbon fibers). The 28-day ultimate flexural strength and impact resistance of MCCF4 increased by 4.6 MPa and 134 blows, respectively, as compared to MCCF0. Moreover, the 28-day ultimate flexural toughness and ultimate impact toughness values of MCCF4 were higher than that of MCCF0, by 3739.7 N-mm and 2703.3 J, respectively. However, MCCF3 (3% carbon fibers) also exhibited a good performance under flexural and impact loadings. Based on the costs of all mortar composites and their performances in both fresh and hardened states, MCCF3 was derived as the best mortar mix. This implies that 3% carbon fibers can be defined as the optimum fiber content in the context of the present study.