新型美容牙科纤维／树脂复合材料桩钉的研制

目的 :研究高强玻璃纤维增强丙烯酸类树脂的力学性能 ;探索复合材料桩钉的成型方法。　方法 :用缠绕法制作预浸料 (S- GF/EAM树脂 ) ,用层压法制成单向纤维 /树脂复合材料 ,并测试其弯曲强度、弯曲模量和层间剪切强度。取适量的预浸料放入自制的模具中按复合材料成型工艺压制桩钉 ,并测试其纤维含量。　结果 :随着纤维含量增加 ,复合材料的弯曲强度和弯曲模量呈显著性增加 (P<0 .0 1) (弯曲强度 :1414.7± 6 4.5 Mpa,弯曲模量 :39.6± 1.6 Gpa) ,用模具压制的桩钉纤维含量为 (6 8.38± 1.6 7% )。　结论 :高强度玻璃纤维对丙烯酸树脂的弯曲性能具有增强作用。高强玻璃纤维 /EAM树脂复合材料桩钉可以满足临床需要。     

A comparative study of physicochemical properties of AH Plus and Epiphany root canal sealants

AIM: To evaluate setting time, solubility and disintegration, flow, film thickness, and dimensional change following setting in a dual-cured resin root canal sealer Epiphany compared with an epoxy-resin-based sealer AH Plus. METHODOLOGY: The experiments were performed according to ANSI/ADA Specification 57 which tests the physicochemical properties of endodontic sealing materials. Five samples of each material were tested for each of the properties. In addition, deionized distilled water from the solubility test of Epiphany was submitted for analysis of the cations Fe, Ni, Ca, Mg, Zn, Na, and K in an atomic absorption spectrometer. Three samples were analysed. RESULTS: There were no statistical differences (P>0.05) in flow (AH Plus: 38.57 mm; Epiphany: 35.74 mm) and film thickness (AH Plus: 10.6 microm; Epiphany: 20.1 microm). The solubility (AH Plus: 0.21%; Epiphany: 3.41%) and dimensional alterations following setting (AH Plus: expansion of 1.3%; Epiphany: expansion of 8.1%) were statistically different (P<0.05). The setting times of both sealants were in accordance with ANSI/ADA requirements. CONCLUSIONS: Setting time, flow, and film thickness tests for both cements conformed to ANSI/ADA standards. Dimensional alteration test for both cements were greater than values considered acceptable by ANSI/ADA. Epiphany values regarding solubility were also greater than values considered acceptable by ANSI/ADA.     

Palatal discrepancies and postdams

To investigate the variation in post-cure palatal discrepancy of dentures, 20 complete maxillary replica dentures were prepared on models with high and low palates and processed by conventional compression moulding and injection moulding. Measurements were made by travelling microscope of the sagittal midline discrepancies between palate and model on three occasions; after processing; after removal of part of the investing plaster; and after immersion in water for 1 month at 37 degrees C. The magnitudes of discrepancies were greatest distally, diminishing with distance anteriorly from the postdam. They increased with partial removal of plaster, and decreased slightly after immersion.     

Temperature rise induced by some light emitting diode and quartz-tungsten-halogen curing units

Because of the risk of thermal damage to the pulp, the temperature rise induced by light-curing units should not be too high. LED (light emitting diode) curing units have the main part of their irradiation in the blue range and have been reported to generate less heat than QTH (quartz-tungsten-halogen) curing units. This study had two aims: first, to measure the temperature rise induced by ten LED and three QTH curing units; and, second, to relate the measured temperature rise to the power density of the curing units. The light-induced temperature rise was measured by means of a thermocouple embedded in a small cylinder of resin composite. The power density was measured by using a dental radiometer. For LED units, the temperature rise increased with increasing power density, in a statistically significant manner. Two of the three QTH curing units investigated resulted in a higher temperature rise than LED curing units of the same power density. Previous findings, that LED curing units induce less temperature rise than QTH units, does not hold true in general.     

A study on surface roughness and microleakage test in cavities prepared by Er:YAG laser irradiation and etched bur cavities

 The purposes of this study were to investigate the surface morphology, suface roughness of cavities prepared by Er:YAG laser irradiation, and compared the microleakage degree after composite resin restoration with etched bur cavities, in vitro. In each of the 30 human extracted teeth, two shallow cavities were prepared; one prepared with the Er:YAG laser system on the buccal surface, and one produced on the lingual (palatal) surface with a high-speed turbine. Five cavities from each group were investigated by scanning electron microscopy (SEM), and five were subjected to surface roughness analysis by a colour laser three-dimensional (3D) microscope. The remaining cavities were filled with a composite resin and subjected to a microleakage test under thermocycling. Only bur cavities were acid-etched before filling. Statistical analysis was performed using the Mann-Whitney U test; a value of p <0.01 was considered significant. Morphologically, the prepared cavities showed an irregular surface with the absence of a debris-like smear layer; enamel prisms and opening of dentinal tubules were recognised. Surface roughness was significantly increased with the laser system. Microleakage test revealed no significant differences between the laser and bur cavities. Crosscut sections of the cavities with no microleakage showed no gap at the interface. Laser cavity may facilitate good adaptation of composite resin with enamel and dentine, because an increase of surface roughness and the openings of dentinal tubules may facilitate the formation of a hybrid zone, since a primer and an adhesive can penetrate the surface better when the smear layer is removed. It can be concluded that shallow cavity prepared by Er:YAG laser is capable of decreasing microleakage of composite resin restorations, and its efficiency is similar to etched bur cavities. Received: 16 July 2001 / Accepted: 5 June 2002     

An in vitro study into the effect of a limited range of denture cleaners on surface roughness and removal of Candida albicans from conventional heat-cured acrylic resin denture base material

This study evaluated the abrasiveness of four denture cleaners on the surface of denture base material and assessed their ability to remove Candida albicans. Acrylic resin discs 20 mm diameter and 2 mm thick were identically produced and polished. Four cleaners were evaluated: conventional toothpaste; toothpaste with stain remover; denture cleaning paste and an immersion type cleaner, and water were used as control. These were used at dilutions of 1:1, 1:2 and 1:3 with water. An electric toothbrush was used, and the discs cleaned to simulate 1 years' cleaning. The surface roughness of the discs were then measured, before and after cleaning, using a stylus profilometer, then inoculated with 1.2 x 10(6)C. albicans cells. The effectiveness of the denture cleaners to remove C. albicans cells was assessed following a single cleaning event. The immersion cleaner was significantly less abrasive than paste cleaners (P < 0.05). There were no significant differences between any dilutions for any cleaner used (P > 0.05). Immersion and paste cleaners removed almost all recoverable C. albicans from the discs, as cleaning with water alone was less effective (P < 0.05). An immersion type cleaner was found to be the most suitable cleaner because of its low abrasivity and effective removal of organic debris.     

Identification of homoserine lactone derivatives using the methionine functionalized solid phase synthesis by gas chromatography/mass spectrometry

Combinatorial homoserine lactone mixtures and individual products were obtained from the methionine-functionalized resin in solid-phase synthesis. The four-step process consisting of a coupling step of an N-Fmoc-L-methionine, deprotection of N-Fmoc group, N-coupling with a carboxylic acid, and cleavage reaction through a polymer supported strategy is described. Gas chromatography-mass selective detector (GC-MSD) techniques provide the most powerful methods for identifying both the combinatorial mixtures and individual products.     

Conservative restoration with resin composites of a case of amelogenesis imperfecta

Amelogenesis imperfecta (AI) is an inherited enamel dysplasia involving both dentitions with no other systemic effects. The hereditary pattern is autosomal or X-related dominant or recessive. Its prevalence is approximately 1:14,000-1:16,000. It can be classified as hypocalcified, hypoplastic and hypomaturated according to clinical, radiological, histological and hereditary findings. This study presents a case of hypomaturated type AI in a 16-year-old young man that was successfully treated with different types of resin composites. The patient was regularly recalled during the one-year postoperative period. Radiographic and clinical examinations at recall revealed no evidence of complications associated with the restored teeth or their supporting structures.     

Raman scattering determination of the depth of cure of light-activated composites: influence of different clinically relevant parameters

The purpose of this research was to determine the depth of cure of light-activated composites in relation with different clinically relevant parameters. A Raman spectroscopic method has been used. The measurement of cure is made on a relative basis by comparing the vibration band of the residual unpolymerized methacrylate C=C bond at 1640 cm-1 against the aromatic C=C stretching band at 1610 cm-1 used as an internal standard. The information gained draw attention to the importance of light transmission during the exposure. The influence of sample's thickness on the depth of cure is illustrated by a second order polynomial regression. The shade and translucency of the resin composite also modify the light transmission and thus have a significant influence on the degree of conversion. Moreover the light-source intensity and the distance from the curing tip are important parameters of influence. A significant reduction of the depth of cure is observed for all sample thickness of resin composite tested when using a light device with an intensity of 300 mW cm-2 as well as using a distance from the curing tip higher than 20 mm.