Influence of mesh materials on collagen deposition in a rat model.

Alterations of the extracellular matrix (ECM) with its major component collagen are increasingly discussed as possible risk factors implicated in the development of abdominal-wall herniation. Because of the widespread use of alloplastic meshes for the surgical repair of hernias, an animal study was performed to analyze the influence of various mesh materials on the quantity and quality of collagen deposition. In 60 male Sprague-Dawley rats an abdominal replacement was performed using three different kinds of mesh materials: polyester (PE), a pure polypropylene (PP), and a composite mesh made of polypropylene and polyglactin (PG). A simple fascia suture repair served as control. The count of fibroblasts, the collagen/protein ratio, the type I/III collagen ratio, and the expression of basic fibroblast growth factor (b-FGF) at the interface were analyzed after 7, 21, and 90 days. The ratio of collagen to overall protein (microg/mg) showed significant differences comparing different mesh materials (sham controls 38.44 +/- 16.33 microg/mg, PE 68.5 +/- 23.8 microg/mg, PP 101.6 +/- 32.3 microg/mg, PG 49.6 +/- 11.6 microg/mg at day 90). The ratio of collagen type I/III increased over time in all groups. However, 90 days after mesh implantation the ratio was always significantly lowered compared to the controls. No significant difference was found comparing different mesh materials. The alteration of the scar composition is closely connected to an increased b-FGF expression. b-FGF and count of fibroblasts highly correlated (r =.95) and showed significant elevated levels compared to simple suture repair. The results of our study strongly support the notion that wound healing is affected by mesh implantation. The quality of the ECM deposition as determined by collagen type I/III ratio is impaired in general, whereas the quantity of ECM deposition is markedly influenced by the kind of mesh material.     

CEA and CA 19.9: an evaluation by new statistical technics on a group of elderly patients

New parametric and non parametric statistical methods have been compared in the evaluation of experimental data of CEA and CA 19.9 using a brief program in BASIC. We have found that the distribution of the two markers is the same of that described in literature except for both the means that we have found being slightly higher than that ones described by other authors.     

Hexamethyldisilazane in preparation of retinal tissue for scanning electron microscopy

A new rapid procedure for desiccating frozen resin-cracked retinal tissue for scanning electron microscopy (SEM) which permits air-drying was found to compare favorably with tissues prepared by critical-point drying: Retinal tissue was fixed in 4% phosphate-buffered neutral formaldehyde, dehydrated by means of graded ethanol, embedded in Epon, cracked and washed in propylene oxide. For desiccation, the specimens were immersed in hexamethyldisilazane (HMDS), air-dried and finally sputter-coated. The method is time-saving, gives extended information in SEM, and the number of good specimens is increased.     

Finite element analysis of a bone-implant system with the proximal femur nail.

Static analysis with finite element of a realistic femur nail bone-implant system in a typical proximal femoral fracture under physiological load bearing situations provides results for stress, displacement and strain. The question to be answered is, if simulation with the finite element analysis is able to explain biomechanically clinical observed patterns of failure. Surface-Reconstruction with CT database of a proximal femur and reconstruction with CT based density data was done. Next steps were to unite the bone structure with the Proximal Femoral Nail and to model two relevant fractures (31-A2.2 and A2.3 according AO). After modelling of geometry, isotropic material behaviour and load application numeric calculation of the femur-nail system with FE-software was performed. FE simulation mainly shows an axial dislocation of the femoral head screw with nearly no dislocation of the antirotation screw. This so-called z-effect therefore means: (1) Tilting of the proximal main fragment around the sagittal axis between the screws and (2) relative movement of both screws in the frontal plane. Relative movement of the two screws against each other could be the reason for implant failure, the so called cut out. Furthermore simulation shows different gliding of the screws explaining the so called z-telescoping. The analyzed stress patterns have to be relativized, because isotropic material behaviour of cancellous bone was assumed. Further examinations for this issue are necessary.     

Medizinische Beurteilungskriterien zu bandscheibenbedingten Berufskrankheiten der Lendenwirbelsäule (I)

Occupational diseases Nos. 2108 and 2110 correspond to intervertebral disc-related diseases of the lumbar spine from many years of carrying or lifting heavy loads, occupations in extreme postures of full flexion or oscillation of the whole body when seated, and which compel the cessation of all activities which are or could be the cause for the origin, exacerbation or recurrence of the disease. These occupational diseases came into force at the start of 1993, but there have been considerable problems in their implementation. The present Part I of the contribution is the result of the work of an interdisciplinary study group and contains medical criteria for the assessment of possibly strain-related clinical characteristics and the evaluation of other possible causes. Part II is to be published in Volume 4/2005 and will deal with questions related to forced cessation and to the assessment of the loss of earning ability. Agreement was reached in many areas related to the assessment of occupational claims. This should allow for evidence-based decision making in the future for the occupational diseases Nos. 2108 and 2110.