Quality of marginal adaptation evaluation of posterior composites in clinical trials

The evaluation of margins of restorations in clinical trials relies on the subjective assessment of evaluators, with no instrument having been developed, let alone validated, to assist in the process. The purpose of the present study was to assess the quality of evaluations of marginal adaptation by analyzing the distribution of marginal steps rated according to clinical criteria. Replicas of 435 restorations, the marginal qualities of which had been evaluated according to modified USPHS criteria, were randomly selected from the Occlusin multi-center clinical trial program. The marginal step height in the most deteriorated area of each restoration was measured by means of a digital step-height instrument. An overlap between the steps in the restorations with A (Alfa; replacement unnecessary) and B (Bravo; replacement questionable) ratings was found to be in the range of 101 microm to 321 microm. When the steps with a height greater or less than one standard deviation of the mean were excluded, the overlap was reduced to a range of 168 micro m to 173 microm. This finding indicates a marginal height boundary between A and B ratings for marginal adaptation of 170 +/- 3 microm.     

Dynamic shear properties of the temporomandibular joint disc

Shear stress might be an important factor associated with fatigue failure and damage of the temporomandibular joint disc. Little information, however, is available on the dynamic behavior of the disc in shear. Since the disc is an anisotropic and viscoelastic structure, in the present study the dependency of the dynamic shear behavior on the direction and frequency of loading was examined. Ten porcine discs were used for dynamic shear tests. Shear stress was applied in both anteroposterior (A-P test) and mediolateral (M-L test) directions. The dynamic moduli increased as the loading frequency increased. The dynamic elasticity was significantly larger in the A-P test than in the M-L test, although the dynamic viscosity was similar in both tests. The present results suggest that non-linearities, compression/shear coupling, and intrinsic viscoelasticity affect the shear material behavior of the disc, which might have important implications for the transmission of load in the temporomandibular joint.     

Incidence of penetration of a blood vessel during inferior alveolar nerve block

Aspiration of the syringe after the needle had been placed in position for an inferior alveolar nerve block (but before the anaesthetic solution was injected) in 250 patients showed that the tip of the needle was in a blood vessel in 49 (20%). Aspiration of blood was significantly more common in patients aged 9-19 years than in all others (P=0.04).     

A virtual reality dental simulator predicts performance in an operative dentistry manikin course

This study was designed to test the ability of a virtual reality dental simulator to predict the performance of students in a traditional operative dentistry manikin course. Twenty-six dental students were pre-tested on the simulator, prior to the course. They were briefly instructed and asked to prepare 12 class I cavities which were automatically graded by the simulator. The instructors in the manikin course that followed were unaware of the students' performances in the simulator pre-test. The scores achieved by each student in the last six simulator cavities were compared to their final comprehensive grades in the manikin course. Class standing of the students in the simulator pre-test positively correlated with their achievements in the manikin course with a correlation coefficient of 0.49 (P = 0.012). Eighty-nine percent of the students in the lower third of the class in the pre-test remained in the low performing half of the class in the manikin course. These results indicate that testing students in a dental simulator, prior to a manikin course, may be an efficient way to allow early identification of those who are likely to perform poorly. This in turn could enable early allocation of personal tutors to these students in order to improve their chances of success.     

Effect of interfacial bond quality on the direction of polymerization shrinkage flow in resin composite restorations

Shrinkage in light curing resin composites is assumed to be directed toward the light source. However, the strong bond at the dentin-resin interface achieved by newer generation dentin bonding systems may affect the direction of polymerization shrinkage. In this study, various curing modes of adhesive resin simulating different bond qualities were applied to determine the extent of interfacial gap formation with a scanning electron microscope. We also measured the free surface depression with a profilometer. The direction of polymerization shrinkage was inferred from the ratio of the interfacial gap measurement at the floor to the free surface depression. Various curing modes used in this study include Group 1: light curing of resin composite without the bonding agent as the negative control; Group 2: simultaneous light curing of the bonding agent and resin composite; Group 3: start of the chemical cure of the dual-cured bonding agent before light curing the resin composite; Group 4: curing the light-initiated bonding agent before insertion and light curing of the resin composite. When the bonding agent was light cured prior to inserting the resin composite (Group 4), the free surface depression was the greatest and the interfacial gap smallest among those in all groups. Therefore, if a good bond between dentin and resin composite can be established, the shrinkage flow will be directed toward a center located near the bonded interface rather than toward the incident light, thus reducing detrimental shrinkage stress.     

Differential scanning calorimetric studies of nickel titanium rotary endodontic instruments

Differential scanning calorimetric (DSC) analyses were performed between -130 degrees and 100 degrees C on specimens prepared from nickel-titanium (NiTi) rotary endodontic instruments: ProFile (n = 5), Lightspeed (n = 4), and Quantec (n = 3). The ProFile and Lightspeed instruments were in the as-received condition, whereas the Quantec instruments were randomly selected from a dental clinic and had unknown history. The DSC plots showed that the ProFile and Lightspeed instruments analyzed had the superelastic NiTi property, with an austenite-finish (Af) temperature of approximately 25 degrees C. Differences in DSC plots for the ProFile instruments and the starting wire blanks (n = 2) were attributed to the manufacturing process. The phase transformation behavior when the specimens were heated and cooled between -130 degrees and 100 degrees C, the temperature ranges for the phase transformations, and the resulting enthalpy changes were similar to those previously reported for nickel-titanium orthodontic wires having superelastic characteristics or shape memory behavior in the oral environment. The experiments demonstrated that DSC is a powerful tool for materials characterization of these rotary instruments, providing direct information not readily available from other analytical techniques about the NiTi phases present, which are fundamentally responsible for their clinical behavior.