Study on Manufacturing via Slip Casting and Properties of Alumina-Titanium Composite Enhanced by Thialite Phase

This paper aims to study the Al₂O₃/Ti ceramic-metal composite obtained by the slip casting method. Samples containing 50% volume of the solid phase, including 10% volume of the metallic phase, were investigated. The rheological properties were analyzed. Thermogravimetric analysis was performed. The properties of the obtained composite determined the phase composition using and SEM/EDS microstructural analysis and the XRD method. The size of the titanium particles equals 20.6 ± 10.1 mm, which corresponds to 27.5% of the initial size and indicates significant fragmentation of the titanium powder during the manufacturing of the composite. The relative density of the fabricated composites was equal to 99%. The slip casting method allows to obtain the proposed composite additionally enhanced by the presence of TiO₂ and Al₂TiO₅ (thialite). Research results revealed a non-Newtonian character of the composite suspension flow with clear thinning under the influence of increasing shear forces. The obtained composites are characterized by the lack of visible defects (cracks, microcracks and delamination) on the surface.     

Solid-State Dewetting as a Driving Force for Structural Transformation and Magnetization Reversal Mechanism in FePd Thin Films

In this work, the process of solid-state dewetting in FePd thin films and its influence on structural transformation and magnetic properties is presented. The morphology, structure and magnetic properties of the FePd system subjected to annealing at 600 °C for different times were studied. The analysis showed a strong correlation between the dewetting process and various physical phenomena. In particular, the transition between the A1 phase and L1₀ phase is strongly influenced by and inextricably connected with solid-state dewetting. Major changes were observed when the film lost its continuity, including a fast growth of the L1₀ phase, changes in the magnetization reversal behavior or the induction of magnetic spring-like behavior.     

Experimental Investigation of the Tensile Behavior of Selected Tire Cords Using Novel Testing Equipment

Aramid and polyamide cords are used in a wide range of applications, particularly in the automotive industry (tire reinforcement) and textile industry for military and fireguard purposes. The problem of the reliable experimental study of tensile behavior of synthetic cords is considered in this paper. In the available standards for synthetic cord testing, particularly ASTM D 885-03, the tensile test must result with the cord damage in the middle of gauge length, and the cords should be fixed in the machine clamps. The trial test gave damage near the clamps. We propose a novel testing stage mounted in the testing machine clamps to achieve the uniform tensile stress distribution in the gauge length of the measured cords. The results of the deformations were measured in two ways: using testing machine head displacement and a videoextensometer. Stress curves of four distinguished cords were evaluated and compared. The second method allowed to acquire results differing from the manufacturers’ data from 0.7% to 21.5%, which allowed for the conclusion that the designed test stand allows for obtaining reliable results for stretched cords.     

Tocilizumab as a first-line biologic treatment in rheumatoid arthritis patients – the impact of concomitant methotrexate treatment and Rheumatic Disease Comorbidity Index on the clinical response – results from the multicenter observational ACT-POL study

ObjectivesAccording to the EULAR recommendations, remission or low disease activity (LDA) in rheumatoid arthritis should be achieved by a maximum of 6 months (M6) of treatment. Data on the use of tocilizumab (TCZ) as first-line biologic treatment in rheumatoid arthritis (RA) in routine clinical practice in Poland are lacking.Material and methodsThis multicenter, non-interventional, prospective, observational study recruited adults, presenting with moderate-to-severe RA, showing an inadequate response or intolerance to disease-modifying antirheumatic drugs, where TCZ was the first-line biologic treatment. The effectiveness of TCZ was assessed by the proportion of patients achieving remission and low disease activity following 6 months of treatment with intravenous TCZ. The impact of comorbidities on treatment outcomes was measured using the Rheumatic Disease Comorbidity Index (RDCI).ResultsTotal remission rates at months 3 and 6 were 6% and 31%, respectively. Low disease activity was reported in 10% and 92% of the patients at 3 and 6 months, respectively. The response was comparable between TCZ as monotherapy and in combination with methotrexate. Mean DAS28 decreased from 6.61 at baseline to 4.27 at the scheduled time of the assessment (3 and 6 months). The Rheumatic Disease Comorbidity Index was not correlated with the number of patients achieving LDA at M3 and M6 or remission rates at M6. Remission rates correlated with RDCI at M3. A total of 114 adverse events were reported in 61 patients, among which five were considered as serious.ConclusionsThe study confirms the effectiveness and safety of TCZ in real-world settings as a first-line biologic treatment in patients with moderate-to-severe RA. Importantly, comorbidities do not affect the results of 6-month treatment with TCZ, that is, the optimal time to achieve at least LDA. Our results may improve the effects of RA therapy in Poland, especially in patients with comorbidities and those who, for various reasons, cannot receive optimal treatment with methotrexate.     

Application of 3D Scanning as an Indirect Method to Analyze and Eliminate Errors on the Manufactured Yoke-Type Forgings Forged in SMED Device on Modernized Crank Press

This article proposes an indirect measurement method based on a dimensional and shape analysis of forgings for the evaluation of the manufacture and the proper operation of the key elements of the crank press, in which after modernization, a quick tool assembly based on SMED (Single Minute Exchange of Die) was implemented. As a result of the introduced changes aiming at improving the forging aggregate and increasing the production efficiency, errors were observed on the manufactured products-forgings in the form of twists and joggles. In order to solve the problem, a lot of advanced methods was used, including: dynamic system of deformation analysis, numerical modeling and as well as dimensional and shape analysis by 3d scanning. Despite the above, this approach (classic way) did not solve the problem. A proprietary method with the use of 3D reverse scanning was proposed, which allows to solve the problem of forgings errors. Based on the measurement results and analyses for a few variants of production cycles, the necessary changes were obtained, making it possible to minimize the errors and obtain proper products in respect of geometry and quality.     

Influence of Gypsum Waste Utilization on Properties and Leachability of Fired Clay Brick

Wastewater treatment activities in the chemical industry have generated abundant gypsum waste, classified as scheduled waste (SW205) under the Environmental Quality Regulations 2005. The waste needs to be disposed into a secure landfill due to the high heavy metals content which is becoming a threat to the environment. Hence, an alternative disposal method was evaluated by recycling the waste into fired clay brick. The brick samples were incorporated with different percentages of gypsum waste (0% as control, 10, 20, 30, 40 and 50%) and were fired at 1050 °C using 1 °C per minute heating rate. Shrinkage, dry density, initial rate of suction (IRS) and compressive strength tests were conducted to determine the physical and mechanical properties of the brick, while the synthetic precipitation leaching procedure (SPLP) was performed to scrutinize the leachability of heavy metals from the crushed brick samples. The results showed that the properties would decrease through the incorporation of gypsum waste and indicated the best result at 10% of waste utilization with 47.5% of shrinkage, 1.37% of dry density, 22.87% of IRS and 28.3% of compressive strength. In addition, the leachability test highlighted that the concentrations of Fe and Al was significantly reduced up to 100% from 4884 to 3.13 ppm (Fe) and from 16,134 to 0.81 ppm (Al), respectively. The heavy metals content in the bricks were oxidized during the firing process, which signified the successful remediation of heavy metals in the samples. Based on the permissible incorporation of gypsum waste into fired clay brick, this study promised a more green disposing method for gypsum waste, and insight as a potential towards achieving a sustainable end product.     

Change in Pull-Out Force during Resorption of Magnesium Compression Screws for Osteosynthesis of Mandibular Condylar Fractures

Background: Magnesium has been used as degradable fixation material for osteosynthesis, but it seems that mechanical strength is still a current issue in these fixations. The aim of this study was to evaluate the axial pull-out force of compression headless screws made of magnesium alloy during their resorption. Methods: The tests included screws made for osteosynthesis of the mandible head: 2.2 mm diameter magnesium alloy MgYREZr (42 screws) and 2.5 mm diameter polylactic-co-glycolic acid (PLGA) (42 pieces, control). The screws were resorbed in Sørensen’s buffer for 2, 4, 8, 12, and 16 weeks, and force was measured as the screw was pulled out from the polyurethane block. Results: The force needed to pull the screw out was significantly higher for MgYREZr screws than for PLGA ones (p < 0.01). Within eight weeks, the pull-out force for MgYREZr significantly decreased to one third of its initial value (p < 0.01). The dynamics of this decrease were greater than those of the pull-out force for PLGA screws (p < 0.05). After these eight weeks, the values for metal and polymer screws equalized. It seems that the described reduction of force requires taking into account when using magnesium screws. This will provide more stable resorbable metallic osteosynthesis.     

MET receptor is a potential therapeutic target in high grade cervical cancer

Cervical cancer is one of the leading causes of death among women suffering from tumors. Current treatment options are insufficient. Here, we investigated the MET receptor as a potential molecular target in advanced cervical cancer. Downregulation of MET receptor expression via RNA interference in different cervical carcinoma cell lines dramatically decreased tumor growth and forced tumor differentiation in vivo. MET receptor silencing also led to a dramatic decrease in cell size and a decrease in proliferation rate under normal and stress conditions. MET receptor downregulation also resulted in decreased cyclin D1 and c-myc levels but did not increase apoptosis. Subsequent experiments showed that downregulation of the MET receptor decreased the expression of a key regulator of the epithelial-to-mesenchymal transition, SLUG. and increased the expression of E-cadherin, a hallmark of the epithelial phenotype. Moreover, MET downregulation impairs expression and signaling of CXCR4 receptor, responsible for invasive phenotype.Taken together, our results strongly suggest that the MET receptor influences the oncogenic properties of cervical carcinoma cells in vitro and in vivo. These findings highlight a unique role of the MET receptor in cervical carcinoma cells and indicate the MET receptor as a potential therapeutic target for advanced cervical carcinoma.     

Effect of variable annular reduction on functional tricuspid regurgitation and right ventricular dynamics in an ovine model of tachycardia-induced cardiomyopathy

ObjectiveTo investigate the effect of variable tricuspid annular reduction (TAR) on functional tricuspid regurgitation (FTR) and right ventricular (RV) dynamics in ovine tachycardia-induced cardiomyopathy.MethodsNine adult sheep underwent implantation of a pacemaker with an epicardial lead and were paced at 200 to 240 bpm until the development of biventricular dysfunction and functional TR was noted. During reoperation on cardiopulmonary bypass, 6 sonomicrometry crystals were placed around the tricuspid annulus (TA) and 14 were placed on the RV epicardium. Annuloplasty suture was placed around the TA and externalized to an epicardial tourniquet. After weaning from cardiopulmonary bypass, echocardiographic, hemodynamic, and sonomicrometry data were acquired at baseline and during 5 progressive TARs achieved with suture cinching. TA area and RV free wall strains and function were calculated from crystal coordinates.ResultsAfter pacing, changes in left ventricular (LV) ejection fraction and RV fractional area decreased significantly. Mean TA diameter increased from 25.1 ± 2.9 mm to 31.5 ± 3.3 mm (P = .005), and median TR (range, 0-3+) increased from 0 (0) to 3 (2) (P = .004). Progressive suture cinching reduced the TA area by 18 ± 6%, 38 ± 11%, 56 ± 10%, 67 ± 9%, and 76 ± 8%. Only aggressive annular reductions (67% and 76%) decreased TR significantly, but these were associated with deterioration of RV function and strain. A moderate annular reduction of 56% led to a substantial reduction of TR with little deleterious effect on regional RV function.ConclusionsA moderate TAR of approximately 50% may be most advantageous for correction of functional TR and simultaneous maintenance of regional RV performance. Additional subvalvular interventions may be needed to achieve complete valvular competence.     

How lonely they are? A degree of isolation among macrozoobenthos species in the Marine Protected Area, the Bay of Puck, the Southern Baltic

Extensive sampling (450 grabs) was performed all over the inner part of Puck Bay (105 km² area) in summers of 2007–2009. The GIS-based analysis of samples was performed to assess in detail the distribution of 32 benthic species. The minimum area of occurrence was less than 1 km² for Lekanosphaera rugicauda and the maximum was 83 km² for Cerastoderma glaucum. The material reveals that species with the pelagic larval stage were most widespread, with the least distance between individuals and the highest average density (e.g. Cerastoderma glaucum, Hydrobia ventrosa). The most isolated and the least dense species within the studied area were discretely mobile, non-larval crustaceans (e.g. Gammarus oceanicus and Lekanosphaera rugicauda), present at single sites with the largest distance from each other. We conclude that analysis of species distribution helps in understanding the threats to populations of marine invertebrates and marine spatial planning, through locating the isolated species and populations.