Experimental and Theoretical Studies on Possibility of Void Filling by Magnesium in Mg-Doped Tetrahedrites

Tetrahedrites, due to their promising thermoelectric properties, are one of the materials being investigated for use in thermoelectric generators. One problem is the lack of n-type tetrahedrites, which would be beneficial for the design of tetrahedrite thermoelectric modules. Preliminary theoretical studies have shown that elements from groups I and II can be introduced into the structural voids of tetrahedrite, acting as donor dopants, and should enable n-type conductivity. Therefore, in this work, an attempt was made to obtain and study magnesium-doped tetrahedrites. A series of samples, Mg_xCu₁₂Sb₄S₁₃, with different magnesium contents were obtained and their phase and chemical compositions were characterized. It was observed that the structural changes occurring upon doping indicate that Mg atoms are likely to be embedded in the structural voids. The experimental studies have been supported by electronic structure calculations indicating that the most likely location of Mg is in the structural voids at the 6b Wyckoff position. Seebeck coefficient and resistivity measurements showed that doping with Mg reduces the concentration of holes, which is consistent with the predicted donor character of the dopant. However, the introduction of magnesium in sufficient amounts to achieve n-type conductivity was not successful.     

The Effect of Antimony (III) Oxide on the Necessary Amount of Precursors Used in Laser-Activated Coatings Intended for Electroless Metallization

The article presents research on the potential use of organometallic compounds with the addition of antimony (III) oxide Sb₂O₃ as a coating additive that will make coatings susceptible to electroless metallization after prior surface irradiation with 193 nm wavelength laser radiation and a different number of laser pulses. The surface modification and activation effects were assessed by optical-imagining as well as by scanning electron microscopy (SEM) with energy dispersive analysis (EDX). It was found that the presence of Sb₂O₃ in the coating made it possible to reduce the content of the copper complex, causing an intensive surface ablation, resulting in the formation of a conical structure with a higher content of metallic copper nuclei.     

The Use of Barley Malt as a Binder in Molding Sand Technology

The aim of this study was to attempt to use barley malt as a natural, organic binder in the technology of molding sand. TGA analysis of the binder was performed, during which temperatures of thermal decomposition of its components were determined. The results of TG/DTG analysis show that a loss of ~75% of mass of the MB binder is organic matter. Over 50% of this is starch. The results indicate the possibility of using a binder made of barley malt as a binding material for quartz sand grains. This fact was confirmed by tests carried out with use of SEM. During the observations, it was found that barley malt forms smooth bridges connecting individual grains of quartz sand. The typical properties of molding sands with barley malt were also determined, compared to sands containing commonly used binders. At the same time, the influence of the content of this binder on flowability, permeability, strength properties, and wear resistance was assessed. It has been found that increasing the binder content in molding mass results in an increase in strength and wear resistance, as opposed to flowability and permeability. Test castings were also made. It was found that the addition of a binder made of barley malt has a positive effect on the surface quality of castings. This was confirmed by roughness measurements of the test castings. At the same time, a tendency to excessive gas evolution during pouring was shown, with higher contents of this binder. Moreover, greater amounts of barley malt in the molding sand (MB 5%) as compared to the lower content (MB 2%) increased the thickness of the burnt layer of the sand by 25%. This is due to the exothermic reaction when more binder is burnt. It is extremely important from the point of view of the regeneration of molding sand.     

Post-stenting intravascular brachytherapy trials on hypercholesterolemic rabbits using 32P liquid sources: implications for prevention of in-stent restenosis

PURPOSE: Liquid sources of radiation delivered in angioplasty balloons may be a convenient self-centering device used for prevention of in-stent restenosis. To test the effectiveness of this method an intravascular brachytherapy study was performed using 32P liquid sources in an animal model. METHODS: The radial dose distribution around angioplasty balloons filled with solutions of Na 2H 32PO 4 was calibrated by thermoluminescence dosimetry. The animal experiments were performed in rabbits with induced hypercholesterolemia. The balloons containing 32P were introduced into iliac arteries immediately after stent implantation. Estimated 7-49 Gy doses required 30-100 min irradiations. Radiation effects were evaluated by comparing the thickness of various components of the artery wall. RESULTS: Doses of 7, 12, 16 or 49 Gy on the internal artery surface required 30-100 min of irradiation. The dose of 49 Gy at "zero" distance corresponding to 16 Gy at 1.0 mm from the balloon surface reduced hypertrophy in every layer of the arterial wall: in the intima the cross-sectional areas were 0.13 versus 0.91 mm 2, in the media were 0.5 versus 0.46 mm 2 and in the adventitia were 0.04 versus 0.3 mm 2 (p <0.05). A dose of 7 Gy at the balloon surface produced adverse irradiation effects: the intimal area of the artery was 2.087 versus 0.857 mm 2, the medial area was 0.59 versus 0.282 mm 2 and the adventitial area was 0.033 versus 0.209 mm 2 in treated and control arteries, respectively. CONCLUSION: Application of a 49 Gy irradiation dose to the internal arterial surface effectively prevented in-stent restenosis.     

Hip arthroplasty after failed internal fixation of the trochanteric fractures in aged patients with co-existent osteoporosis]

The authors present the results of hip arthroplasty of 67 patients treated after failed internal fixation of the osteoporotic, trochanteric fractures of the femur, which were primary stabilised with angular plate AO in 39 patients and with dynamic hip screw (DHS) in 28 patients. In the discussed material 16 persons were male and 51 female, in the age between 51 and 83 years old. According to the Evans classification in 4 cases we diagnosed type I of fracture, in 10--type II, 31--type III and in 22--type IV. Hip arthroplasty was made from the 3rd to the 39th week after primary fixation of the fracture. In 42 patients we made total hip arthroplasty, in 14 cases Austin-Moore hemiarthroplasty, and in 11 patients bipolar arthroplasty. According to the Postel and Merle d'Aubigne classification there were obtained 29 very good, 21 good and 17 satisfactory results.     

Reconstruction of soft tissue defects of the fingers using homodigital V-Y flap]

A series of 54 patients is presented in which full-thickness soft-tissue defects on 57 digits were reconstructed using homodigital V-Y flaps. This is a modification of the Moberg procedure, which was designed for coverage of injuries of distal thumb. The V-Y flap is pedicled on two digital neurovascular bundles, possible advancement is up to 2 cm, and V-shaped base of the flap allows direct closure of the proximal defect, without skin grafting. This technique was used for the reconstruction both volar and dorsal tissue defects of the fingers. All flaps healed within 2-4 weeks. 14 patients (15 fingers) were evaluated after they recovered. In all affected fingers active range of motion was satisfactory, only with slight defect of extension in 2 cases. However, sensation of the light touch was decreased in 10 fingers, and 2PD discrimination was abnormal in 5 fingers. The versatility of V-Y technique in various clinical occasions and its low risk of complications was emphasized. This method is very useful, easy to learn even for trainees unfamiliar with microsurgery.