Effect of Thermal Aging on the Mechanical Properties of High Tenacity Polyester Yarn

Textile materials produced from a high tenacity industrial polyester fiber are most widely used in the mechanical rubber goods industry to reinforce conveyor belts, tire cords, and hoses. Reinforcement of textile rubber undergoes a vulcanization process to adhere the textile materials with the rubber and to enhance the physio-mechanical properties of the product. The vulcanization process has an influence on the textile material being used as a reinforcement. In this work, the effects of aging temperature and time on the high tenacity polyester yarn’s mechanical and surface structural properties were investigated. An experiment was carried out on a pre-activated high tenacity polyester yarn of different linear densities, by aging the yarn specimens under various aging temperatures of 140, 160, 200, and 220 °C for six, twelve, and thirty-five minutes of aging time. The tensile properties and surface structural change in the yarns pre- and post-aging were studied. The investigation illustrates that aging time and temperature influence the surface structure of the fiber, tenacity, and elongation properties of the yarn. Compared to unaged yarn, an almost five times higher percentage of elongation was obtained for the samples aged at 220 °C for 6 min, while the lowest tenacity was obtained for the sample subjected to aging under 220 °C for 35 min.     

The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes

Al-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and potential of the operating anode. The distribution of In and Zn in the tested alloys was mapped by means of the EDX technique, which demonstrated that these elements dissolve well in the alloy matrix and are evenly distributed within it. The current capacity of such alloys was determined by means of the method of determining the mass loss during the dissolution by a current of known charge. The results obtained demonstrate that the current capacity of Al-Zn-In alloy decreases with the increase in the In content, which results in an increased consumption of anode material and shorter lifetime of anodes. With 0.02% In content, the capacity amounted to approx. 2500 Ah/kg, whereas the alloy with 0.2% In had as much as 30% lower capacity amounting to approx. 1750 Ah/kg. Microscopic examination for the morphology and surface profile of the samples after their exposure demonstrated that a higher indium content in the alloy results in a more uneven general corrosion pattern during the dissolution of such alloy, and the cavities (pits) appearing on the alloy surface are larger and deeper. As the indium content is increased from 0.02% to 0.05%, the Al-Zn-In alloy potential decreases by about 50 mV to −1100 mV vs. Ag/AgCl electrode, which is advantageous in terms of using this alloy as a sacrificial anode. When the indium content is further increased from 0.05% to 0.2%, the potential of the alloy is no longer changed to a more negative one. The results obtained from all these tests demonstrate that alloys containing up to 0.05% of In additive are practically applicable for cathodic protection.     

Strength Properties of Structural Glulam Elements from Pine (Pinus sylvestris L.) Timber Reinforced in the Tensile Zone with Steel and Basalt Rods

The study analyzed potential applicability for asymmetric reinforcement of glulam beams using materials with a higher modulus of elasticity. Reinforcement elements included smooth and ribbed steel rods as well as basalt rods. These rods were placed only in the tensile zone, assuming that they will not only impart increased rigidity but first of all will reduce the scatter of bending strength values. What is significant, tests were conducted on timber with defects, as it is most commonly used in industrial practice. Analyses showed that this provides an increase in rigidity close to the assumed level. A significant increase in strength was observed. The manufactured beams reinforced with steel and basalt rods were characterized by mean bending strength amounting to 54 and 47 N/mm², respectively. However, no significant improvement was found in the scatter of the observed variable. Beams reinforced with steel exhibit a 20% higher strength than unreinforced beams. The lower strength of beams reinforced with basalt bars may be related to the lower modulus of elasticity of the basalt itself.     

Foundation Piles—A New Feature for Concrete 3D Printers

Foundation piles that are made by concrete 3D printers constitute a new alternative way of founding buildings constructed using incremental technology. We are currently observing very rapid development of incremental technology for the construction industry. The systems that are used for 3D printing with the application of construction materials make it possible to form permanent formwork for strip foundations, construct load-bearing walls and partition walls, and prefabricate elements, such as stairs, lintels, and ceilings. 3D printing systems do not offer soil reinforcement by making piles. The paper presents the possibility of making concrete foundation piles in laboratory conditions using a concrete 3D printer. The paper shows the tools and procedure for pile pumping. An experiment for measuring pile bearing capacity is described and an example of a pile deployment model under a foundation is described. The results of the tests and analytical calculations have shown that the displacement piles demonstrate less settlement when compared to the analysed shallow foundation. The authors indicate that it is possible to replace the shallow foundation with a series of piles combined with a printed wall without locally widening it. This type of foundation can be used for the foundation of low-rise buildings, such as detached houses. Estimated calculations have shown that the possibility of making foundation piles by a 3D printer will reduce the cost of making foundations by shortening the time of execution of works and reducing the consumption of construction materials.     

Mechanical and Combustion Properties of Agglomerates of Wood of Popular Eastern European Species

The objective of the reported project was to produce wood agglomerates from popular East European species to determine their strength and combustion properties. Closed-die pellets were produced from sawdust of six types of wood common on the East European market: pine, willow, oak, poplar, birch, and beech. The properties of pellets, determined by the type of wood, were influenced by the compaction pressure and the moisture content of the sawdust. The highest average pellet density was obtained for oak sawdust, while the lowest density was obtained for poplar pellets. Expansion of pellets after removing from the die was found to be dependent on the wood species, and as expected, on compaction pressure. The pellet expansion increased after 2 h of conditioning in the laboratory and with an increase in moisture content. The highest and the smallest strength were obtained for oak pellets and for birch sawdust, respectively. The strength of the pellets increased by more than 100% with an increase in the compaction pressure from 60 MPa to 120 MPa. The average strength decreased by 65% with increasing moisture content. For all tested materials, drop resistance remained at a high level, acceptable in industrial practice. The highest calorific value of 18.97 MJ/kg was obtained for pine pellets. The highest ash value of 1.52% was obtained for willow pellets and the lowest value of 0.32% for pine pellets.     

Synthesis and investigation of new cyclic molecules using the stilbene scaffold

A new approach to the synthesis of asymmetrical cyclic compounds using a stilbene scaffold has been developed. The use of boron trifluoride diethyl etherate as the catalyst, both with and without paraformaldehyde, allows us to obtain new substituted dioxanes, oxanes, cyclic compounds or dimer. The analysis of products was run using experimental and theoretical methods.

A new approach to the synthesis of asymmetrical cyclic compounds using a stilbene scaffold has been developed.

Various macrocycles have been widely investigated due to their interesting conformational characteristics and abundant host–guest properties. New macrocyclic receptors with high selectivity in molecular recognition are being looked for,¹ because they have many possible applications in the construction of diverse supramolecular systems.^2–15 In particular, various drug-delivery systems for tumours are being tested and looked at. Development of most solid tumours is strictly associated with the formation of their own functional vascular supply, the network of which is typically obtained in the process of angiogenesis from the host''s normal vascular system. The particular occurrence of tumour neo-vasculature is regarded as a well-fitting target for cancer cell annihilation. Two forms of vascular targeting agents (VTAs) can be distinguished. The first category concerns the substances that inhibit the angiogenesis process (they are referred to as the angiogenesis inhibitors, AIs). The second variant (referred to as the vascular disrupting agents, VDAs),¹⁶ are the compounds harmful to the already-established vessels. Combretastatins CA1P (OXi4503) and CA4P (a subtype of natural phenols) are new vascular disrupting and vascular targeting agents.¹⁶ They exhibit significant abilities of gastric tumour metastasis inhibition and of antitumor immune reactivity enhancement.¹⁷ These compounds additionally contain a notable characteristic of differentiated methoxy groups in the framework. Continuing our study concerning the synthesis and searching the biological activity of stilbenes¹⁸ and drug-delivery systems for tumours, we directed our attention to the new substituted dioxanes, oxanes, and cyclic compounds. We conducted studies on the reaction of substituted stilbenes and paraformaldehyde in the presence of a Lewis acid as the catalyst (BF₃·OEt₂) (​and2).2). The acid-catalyzed condensation of olefins with aldehydes, the Prins reaction, is generally used for the preparation of 1,3-dioxanes.¹⁹ The major products of the classical Prins reaction are normally 1,3-dioxanes, 1,3-glycols, or unsaturated alcohols depending on the reaction conditions¹⁹ (Fig. 1). The aza-Prins cyclization, which is the nitrogen version of the reaction, is of particular interest. The reaction permits rapid access to azaheterocycles and the wide applicability and usefulness of the aza-Prins reaction have been demonstrated by the synthesis of a variety of complex natural products.²⁰The compounds of (7–10) obtained from the reaction of suitable stilbene derivatives (1–4) with paraformaldehyde and BF₃·OEt₂ as the catalyst^a

Zirconia–Alumina Composites Obtained by Centrifugal Slip Casting as Attractive Sustainable Material for Application in Construction

This paper focuses on the possibility of adapting the centrifugal slip casting method to obtain zirconia–alumina composite materials in the form of finished tube-shaped products. These types of products, due to their unique properties, can be utilised, for example, in the transport of aggressive substances, even in extreme temperatures or corrosive conditions. The study reports on the two series of zirconia–alumina composites differing in the content of ZrO₂—2.5 and 25 vol%. The fabricated and sintered materials were characterised using scanning electron microscopy (SEM), X-ray diffraction (XRD) and stereological analysis. Moreover, a life cycle assessment (LCA) was provided in accordance with the requirements of the ISO 14044 and EN 15805 standards. The obtained data clearly show that the centrifugal slip casting method allows obtaining samples with high density and extremely uniform distribution of the ZrO₂ phase in the alumina matrix. The stereological analysis results proved also that the addition of ZrO₂ is effective in reducing the growth of Al₂O₃ grains during the sintering process. The phase analysis carried out by means of XRD showed that during the sintering process, in the case of composites with a lower ZrO₂ content (2.5 vol%), the monoclinic to tetragonal transformation of ZrO₂ was total, while for samples containing 25 vol% ZrO₂, the monoclinic phase remained in a small amount in the final product.     

Influence of Modified Epoxy Resins on Peroxide Curing,Mechanical Properties and Adhesion of SBR,NBR and XNBR to Silver Wires—Part II: Application of Carboxy-Containing Peroxy Oligomer (CPO)

This research was aimed at verifying the effect of carboxy-containing peroxy oligomer (CPO) addition on the possibility of rubber crosslinking and a subsequent adhesion of the modified rubber to silver wires. Three commonly industrially used rubbers were selected for the study: styrene–butadiene rubber (SBR), acrylonitrile–butadiene rubber (NBR) and carboxylated acrylonitrile–butadiene rubber (XNBR), together with carboxy-containing peroxy oligomer (CPO). An improvement in the adhesion of rubbers to silver wires was observed when applying the oligomeric peroxide with functional groups, with no deterioration of mechanical properties of the vulcanizates. Crosslinking synergy between dicumyl peroxide (DCP) and the modifier could hardly be observed. Nevertheless, the studies demonstrated, that to a small extent, even the CPO itself can crosslink NBR and especially XNBR, resulting in a material of notable elasticity and adhesion to silver wires.