Effect of Low Zeolite Doses on Plants and Soil Physicochemical Properties

Thousands of tons of zeolitic materials are used yearly as soil conditioners and components of slow-release fertilizers. A positive influence of application of zeolites on plant growth has been frequently observed. Because zeolites have extremely large cation exchange capacity, surface area, porosity and water holding capacity, a paradigm has aroused that increasing plant growth is caused by a long-lasting improvement of soil physicochemical properties by zeolites. In the first year of our field experiment performed on a poor soil with zeolite rates from 1 to 8 t/ha and N fertilization, an increase in spring wheat yield was observed. Any effect on soil cation exchange capacity (CEC), surface area (S), pH-dependent surface charge (Qv), mesoporosity, water holding capacity and plant available water (PAW) was noted. This positive effect of zeolite on plants could be due to extra nutrients supplied by the mineral (primarily potassium—1 ton of the studied zeolite contained around 15 kg of exchangeable potassium). In the second year of the experiment (NPK treatment on previously zeolitized soil), the zeolite presence did not impact plant yield. No long-term effect of the zeolite on plants was observed in the third year after soil zeolitization, when, as in the first year, only N fertilization was applied. That there were no significant changes in the above-mentioned physicochemical properties of the field soil after the addition of zeolite was most likely due to high dilution of the mineral in the soil (8 t/ha zeolite is only ~0.35% of the soil mass in the root zone). To determine how much zeolite is needed to improve soil physicochemical properties, much higher zeolite rates than those applied in the field were studied in the laboratory. The latter studies showed that CEC and S increased proportionally to the zeolite percentage in the soil. The Qv of the zeolite was lower than that of the soil, so a decrease in soil variable charge was observed due to zeolite addition. Surprisingly, a slight increase in PAW, even at the largest zeolite dose (from 9.5% for the control soil to 13% for a mixture of 40 g zeolite and 100 g soil), was observed. It resulted from small alterations of the soil macrostructure: although the input of small zeolite pores was seen in pore size distributions, the larger pores responsible for the storage of PAW were almost not affected by the zeolite addition.     

Al2O3/ZrO2 Materials as an Environmentally Friendly Solution for Linear Infrastructure Applications

The present work deals with the evaluation of the effect of ZrO₂ on the structure and selected properties of shapes obtained using the centrifugal slip casting method. The samples were made of alumina and zirconia. The applied technology made it possible to produce tubes with a high density reaching 99–100% after sintering. Very good bonding was obtained at the Al₂O₃/ZrO₂ interphase boundaries with no discernible delamination or cracks, which was confirmed by STEM observations. In the case of Al₂O₃/ZrO₂ composites containing 5 vol.% and 10 vol.% ZrO₂, the presence of equiaxial ZrO₂ grains with an average size of 0.25 µm was observed, which are distributed along the grain boundaries of Al₂O₃. At the same time, the composites exhibited a very high hardness of 22–23 GPa. Moreover, the environmental influences accompanying the sintering process were quantified. The impacts were determined using the life cycle analysis method, in the phase related to the extraction and processing of raw materials and the process of producing Al₂O₃/ZrO₂ composites. The results obtained show that the production of 1 kg of sintered composite results in greenhouse gas emissions of 2.24–2.9 kg CO₂ eq. which is comparable to the amount of emissions accompanying the production of 1 kg of Polyvinyl Chloride (PVC), Polypropylene (PP), or hot-rolled steel products.     

New Acceptor–Donor–Acceptor Systems Based on Bis-(Imino-1,8-Naphthalimide)

In this paper, six novel symmetrical bis-(imino-1,8-naphthalimides) differing in core and N-substituent structure were synthesized, and their thermal (TGA, DSC), optical (UV-Vis, PL), electrochemical (DPV, CV) properties were evaluated. The compounds were stable to 280 °C and could be transferred into amorphous materials. Electrochemical investigations showed their ability to occur reductions and oxidations processes. They exhibited deep LUMO levels of about −3.22 eV and HOMO levels above −5.80 eV. The optical investigations were carried out in the solutions (polar and non-polar) and in films and blends with PVK:PBD. Bis-(imino-1,8-naphthalimides) absorbed electromagnetic radiation in the range of 243–415 nm and emitted light from blue to yellow. Their capacity for light emission under voltage was preliminarily tested in devices with an active layer consisting of a neat compound and a blend with PVK:PBD. The diodes emitted green or red light.     

Mechanical and Combustion Properties of Agglomerates of Wood of Popular Eastern European Species

The objective of the reported project was to produce wood agglomerates from popular East European species to determine their strength and combustion properties. Closed-die pellets were produced from sawdust of six types of wood common on the East European market: pine, willow, oak, poplar, birch, and beech. The properties of pellets, determined by the type of wood, were influenced by the compaction pressure and the moisture content of the sawdust. The highest average pellet density was obtained for oak sawdust, while the lowest density was obtained for poplar pellets. Expansion of pellets after removing from the die was found to be dependent on the wood species, and as expected, on compaction pressure. The pellet expansion increased after 2 h of conditioning in the laboratory and with an increase in moisture content. The highest and the smallest strength were obtained for oak pellets and for birch sawdust, respectively. The strength of the pellets increased by more than 100% with an increase in the compaction pressure from 60 MPa to 120 MPa. The average strength decreased by 65% with increasing moisture content. For all tested materials, drop resistance remained at a high level, acceptable in industrial practice. The highest calorific value of 18.97 MJ/kg was obtained for pine pellets. The highest ash value of 1.52% was obtained for willow pellets and the lowest value of 0.32% for pine pellets.     

Influence of the Type of Cement on the Action of the Admixture Containing Aluminum Powder

The study of the effect of cement type on the action of an admixture increasing the volume of concrete (containing aluminum powder), used in amounts of 0.5–1.5% of cement mass, was presented. The tests were carried out on cement mortars with Portland (CEM I) and ground granulated blast-furnace slag cement (CEM III). The following tests were carried out for the tested mortars: the air content in fresh mortars, compressive strength, flexural strength, increase in mortar volume, bulk density, pore structure evaluation (by the computer image analysis method) and changes in the concentration of OH⁻ ions during the hydration of used cements. Differences in the action of the tested admixture depending on the cement used were found. To induce the expansion of CEM III mortars, a smaller amount of admixture is required than in the case of CEM I cement. Using the admixture in amounts above 1% of the cement mass causes cracks of mortars with CEM III cement due to slow hydrogen evolution, which occurs after mortar plasticity is lost. The use of an aluminum-containing admixture reduces the strength properties of the cement mortars, the effect being stronger in the case of CEM III cement. The influence of the sample molding time on the admixture action was also found.     

Influence of Long-Term Storage on the Caking Properties Determined in Punch Test and Fungal Contamination of Potato Starch and Wheat Flour

The presented results are an attempt to identify the changes taking place during a punch test experiment and the development of fungal impurities of powdered food materials over long-term storage at 75% RH. The potato starch and wheat flour market has a large share of the global production of bulk materials. The growing interest in powdered food materials requires additional production expenditure. This is associated with an increase in storage time of the discussed product and providing it with the appropriate conditions. The samples of potato starch and wheat flour were stored in perforated containers in a climatic chamber at 75% humidity and 21 °C for five months and then samples were measured by a punch test in a Lloyd LRX materials testing machine. The graphs obtained in the potato starch punch test differed significantly from wheat flour. The thickening of potato starch was observed in the form of layers, while potato starch was uniformly thickened throughout the experiment. The conditions of 75% humidity and 21 °C can be described as the beginning of the caking process. In potato starch, linear sections were observed, which changed the length of their storage time and, additionally, was correlated with the appearance of fungal contamination. These results may suggest the influence of fungi on the phenomenon of bulk material caking.     

Straw/Nano-Additive Hybrids as Functional Fillers for Natural Rubber Biocomposites

Currently, up to 215 million metric tons of harvestable straw are available in Europe, 50% of the crops come from wheat, 25% from barley and 25% from maize. More than half of the production remains undeveloped. The overproduction of straw in the world means that the current methods of its management are insufficient. The article describes the production method and characterization of natural rubber biocomposites containing cereal straw powder modified with functional nano-additives in the form of carbon black, silica and halloysite nanotubes. The use of cereal straw in the elastomer matrix should contribute to obtaining a product with good mechanical properties while ensuring a low cost of the composite. In turn, the application of the mechanical modification process will allow the combination of specific properties of raw materials to obtain new, advanced elastomeric materials. As part of the work, hybrid fillers based on mechanically modified cereal straw were produced. The impact of hybrid fillers on mechanical, rheometric and damping properties was assessed. The flammability and susceptibility of the obtained biocomposites to aging processes were determined. The use of hybrid fillers based on mechanically modified straw allowed us to obtain a higher cross-linking density of vulcanizates (even up to 40% compared to the reference sample), and thus higher values of the rheometric moment during the vulcanization process of rubber mixtures (from approx. 10% (10 phr of filler) up to 50% (30 phr of filler) in relation to the unfilled system) and higher hardness of vulcanizates (by about 30–70%). The curing time of the blends was slightly longer, but the obtained composites were characterized by significantly higher tensile strength. The use of fillers in the elastomer matrix increased the modulus at 100, 200 and 300% and the elongation at break. Moreover, greater resistance of vulcanizates to the combustion process was confirmed.     

On Investigating the Microstructural,Mechanical, and Tribological Properties of Hybrid FeGr1/SiC/Gr Metal Matrix Composites

In recent years, studies of different properties of hybrid metal matrix composites, as well as very detailed issues, have been published. In this article, ready-made iron, graphite, and silicon carbide powders were used to produce the base material and composites. An analysis of some microstructural and mechanical properties, as well as the tribological behavior of metal matrix composites (MMCs), based on FeGr1 sintered material with the single and hybrid addition of a silicon carbide and graphite was undertaken. During the study, the flexural and compressive strength of MMCs were analyzed and changes of the momentary coefficient of friction, the temperature of friction, as well as wear rates of the MMCs tested were monitored. Based on the results, it was revealed that wear rates decreased 12-fold in comparison to the base material when SiC or SiC + Gr were added. Further research into MMCs with ceramic particle additives is proposed.     

Zirconia–Alumina Composites Obtained by Centrifugal Slip Casting as Attractive Sustainable Material for Application in Construction

This paper focuses on the possibility of adapting the centrifugal slip casting method to obtain zirconia–alumina composite materials in the form of finished tube-shaped products. These types of products, due to their unique properties, can be utilised, for example, in the transport of aggressive substances, even in extreme temperatures or corrosive conditions. The study reports on the two series of zirconia–alumina composites differing in the content of ZrO₂—2.5 and 25 vol%. The fabricated and sintered materials were characterised using scanning electron microscopy (SEM), X-ray diffraction (XRD) and stereological analysis. Moreover, a life cycle assessment (LCA) was provided in accordance with the requirements of the ISO 14044 and EN 15805 standards. The obtained data clearly show that the centrifugal slip casting method allows obtaining samples with high density and extremely uniform distribution of the ZrO₂ phase in the alumina matrix. The stereological analysis results proved also that the addition of ZrO₂ is effective in reducing the growth of Al₂O₃ grains during the sintering process. The phase analysis carried out by means of XRD showed that during the sintering process, in the case of composites with a lower ZrO₂ content (2.5 vol%), the monoclinic to tetragonal transformation of ZrO₂ was total, while for samples containing 25 vol% ZrO₂, the monoclinic phase remained in a small amount in the final product.     

Overview of Materials Used for the Basic Elements of Hydraulic Actuators and Sealing Systems and Their Surfaces Modification Methods

The article is an overview of various materials used in power hydraulics for basic hydraulic actuators components such as cylinders, cylinder caps, pistons, piston rods, glands, and sealing systems. The aim of this review is to systematize the state of the art in the field of materials and surface modification methods used in the production of actuators. The paper discusses the requirements for the elements of actuators and analyzes the existing literature in terms of appearing failures and damages. The most frequently applied materials used in power hydraulics are described, and various surface modifications of the discussed elements, which are aimed at improving the operating parameters of actuators, are presented. The most frequently used materials for actuators elements are iron alloys. However, due to rising ecological requirements, there is a tendency to looking for modern replacements to obtain the same or even better mechanical or tribological parameters. Sealing systems are manufactured mainly from thermoplastic or elastomeric polymers, which are characterized by low friction and ensure the best possible interaction of seals with the cooperating element. In the field of surface modification, among others, the issue of chromium plating of piston rods has been discussed, which, due, to the toxicity of hexavalent chromium, should be replaced by other methods of improving surface properties.