Surface Finish Analysis in Single Point Incremental Sheet Forming of Rib-Stiffened 2024-T3 and 7075-T6 Alclad Aluminium Alloy Panels

The article presents the results of the analysis of the interactions between the single point incremental forming (SPIF) process parameters and the main roughness parameters of stiffened ribs fabricated in Alclad aluminium alloy panels. EN AW-7075-T6 and EN AW-2024-T3 Alclad aluminium alloy sheets were used as the research material. Panels with longitudinal ribs were produced with different values of incremental vertical step size and tool rotational speed. Alclad is formed of high-purity aluminium surface layers metallurgically bonded to aluminium alloy core material. The quality of the surface roughness and unbroken Alclad are key problems in SPIF of Alclad sheets destined for aerospace applications. The interactions between the SPIF process parameters and the main roughness parameters of the stiffened ribs were determined. The influence of forming parameters on average roughness Sa and the 10-point peak–valley surface roughness Sz was determined using artificial neural networks. The greater the value of the incremental vertical step size, the more prominent the ridges found in the inner surface of stiffened ribs, especially in the case of both Alclad aluminium alloy sheets. The predictive models of ANNs for the Sa and the Sz were characterised by performance measures with R² values lying between 0.657 and 0.979. A different character of change in surface roughness was found for sheets covered with and not covered with a soft layer of technically pure aluminium. In the case of Alclad sheets, increasing the value of the incremental vertical step size increases the value of the surface roughness parameters Sa and Sz. In the case of the sheets not covered by Alclad, reduction of the tool rotational speed increases the Sz parameter and decreases the Sa parameter. An obvious increase in the Sz parameter was observed with an increase in the incremental vertical step size.     

Mechanical,Chemical, and Processing Properties of Specimens Manufactured from Poly-Ether-Ether-Ketone (PEEK) Using 3D Printing

As part of the experiments herein, the mechanical properties of specimens made of poly-ether-ether-ketone (PEEK) material using 3D printing technology were determined. Two populations of specimens were investigated, the first of which contained an amorphous structure, while the other held a crystal structure. The studies also investigated the influence of the print directionality on the mechanical properties obtained. Static tensile, three-point bending, and impact tests were carried out. The results for the effect of the structure type on the tensile properties showed that the modulus of elasticity was approximately 20% higher for the crystal than for the amorphous PEEK form. The Poisson’s ratios were similar, but the ratio was slightly higher for the amorphous samples than the crystalline ones. Furthermore, the studies included a chemical PEEK modification to increase the hydrophilicity. For this purpose, nitrite and hydroxyl groups were introduced into the chain by chemical reactions. The results demonstrate that the modified PEEK specimens had worse thermoplastic properties than the unmodified specimens.     

Effect of Co Substitution and Thermo-Magnetic Treatment on the Structure and Induced Magnetic Anisotropy of Fe84.5−xCoxNb5B8.5P2 Nanocrystalline Alloys

In the present work, we investigated in detail the thermal/crystallization behavior and magnetic properties of materials with Fe_84.5-xCo_xNb₅B_8.5P₂ (x = 0, 5, 10, 15 and 20 at.%) composition. The amorphous ribbons were manufactured on a semi-industrial scale by the melt-spinning technique. The subsequent nanocrystallization processes were carried out under different conditions (with/without magnetic field). The comprehensive studies have been carried out using differential scanning calorimetry, X-ray diffractometry, transmission electron microscopy, hysteresis loop analyses, vibrating sample magnetometry and Mössbauer spectroscopy. Moreover, the frequency (up to 300 kHz) dependence of power losses and permeability at a magnetic induction up to 0.9 T was investigated. On the basis of some of the results obtained, we calculated the values of the activation energies and the induced magnetic anisotropies. The X-ray diffraction results confirm the surface crystallization effect previously observed for phosphorous-containing alloys. The in situ microscopic observations of crystallization describe this process in detail in accordance with the calorimetry results. Furthermore, the effect of Co content on the phase composition and the influence of annealing in an external magnetic field on magnetic properties, including the orientation of the magnetic spins, have been studied using various magnetic techniques. Finally, nanocrystalline Fe_64.5Co₂₀Nb₅B_8.5P₂ cores were prepared after transverse thermo-magnetic heat treatment and installed in industrially available portable heating equipment.     

Nanostructuring of Si substrates by a metal-assisted chemical etching and dewetting process

In this work, we reported on the development of lithography-free technology for the fabrication of nanopatterned Si substrates. The combination of two phenomena, the solid-state dewetting process and metal-assisted wet chemical etching, allowed for fabrication of Si nanocolumns on large areas in a relatively simple way. The process of dewetting the thin metal layer enabled formation of nickel nanoislands, which were used as a shadow mask in the deposition of a catalytic metal pattern. Application of the two-stage dewetting process with the repetition of the metal deposition and annealing step enabled us to obtain a significant increase in the surface coverage ratio and the surface density of the nanoislands. As a catalytic metal, a gold layer was applied in the metal-assisted wet chemical etching process. The obtained columnar nanostructures showed a great verticality and had a high aspect ratio. In the conducted studies, the maximum etching rate (at RT) was higher than 1.2 μm min⁻¹. The etching rate increased with increasing concentration of oxidizing (H₂O₂) and etching (HF) agent, with a tendency to saturate for more concentrated solutions. The etching rate was significantly higher for Si substrates with a crystallographic orientation (115) than for (111), but there was no privileged direction of etching except for the direction vertical to the substrate. With increasing layer thickness of the catalytic metal a decrease in the metal-assisted wet chemical etching process efficiency was observed. The developed technology allows for fabrication of patterned substrates with a wide range of lateral dimension of nanocolumns and their density.

In this work, we reported on the development of lithography-free technology for the fabrication of nanopatterned Si substrates.     

Synthesis,Polymorphism and Thermal Decomposition Process of (n-C4H9)4NRE(BH4)4 for RE = Ho,Tm and Yb

In total, three novel organic derivatives of lanthanide borohydrides, n-But₄NRE(BH₄)₄ (TBAREB), RE = Ho, Tm, Yb, have been prepared utilizing mechanochemical synthesis and purified via solvent extraction. Studies by single crystal and powder X-ray diffraction (SC-XRD and PXRD) revealed that they crystalize in two polymorphic forms, α- and β-TBAREB, adopting monoclinic (P2₁/c) and orthorhombic (Pnna) unit cells, previously found in TBAYB and TBAScB, respectively. Thermal decomposition of these compounds has been investigated using thermogravimetric analysis and differential scanning calorimetry (TGA/DSC) measurements, along with the analysis of the gaseous products with mass spectrometry (MS) and with analysis of the solid decomposition products with PXRD. TBAHoB and TBAYbB melt around 75 °C, which renders them new ionic liquids with relatively low melting points among borohydrides.     

Clinical Covariates of Abnormal Heart Rate Turbulence in Coronary Patients

Background: The aim of this study is to evaluate the association between heart rate turbulence (HRT) parameters and clinical characteristics of coronary artery disease (CAD) patients. Methods and Results: In 122 patients (mean age 62 ± 9 years) with angiographically documented CAD, 24‐hour Holter monitoring with HRT analysis was performed to evaluate turbulence onset (TO) and turbulence slope (TS). There was a significant correlation between TO and TS (P =?0.31; P < 0.001) . According to quartile values, TO ≥?0.37% and TS ≤ 4.25 ms/RR were considered as abnormal in this patient population. Average values of TO were higher and TS lower in patients over 60 years, in patients with a past history of myocardial infarction and in those with EF < 40%. Considering pharmacotheraphy, higher (better) values of TS were observed in patients on statins, nitrates, and beta‐blockers while lower TS values were noted in patients on calcium blockers. Patients with abnormal parameters of HRT compared to group with normal HRT values were characterized by features of more advanced CAD: age over 60 years (75% vs 49%), past history of MI (75% vs 64%), and EF < 40% (25% vs 3%). Multivariate analysis revealed age > 60 years (OR 1.27; P = 0.002) and EF < 40% (OR 1.39; P = 0.001) as independent clinical factors associated with abnormal HRT parameters. Conclusions: HRT parameters are influenced by clinical characteristics and pharmacotherapy of studied patients with TS more than abnormal TO depending on clinical characteristics of patients. Advanced age, prior myocardial infarction and left ventricular dysfunction are key factors influencing values of HRT parameters.     

Correction: MOF-5 derived carbon as material for CO2 adsorption

Correction for ‘MOF-5 derived carbon as material for CO₂ absorption’ by Wojciech Kukulka et al., RSC Adv., 2019, 9, 18527–18537.

The authors regret that the title shown in the original article and several sentences were incorrect due to the use of the word “absorption” in place of “adsorption”. The correct title is as shown above and all instances of “absorption” in the text should be “adsorption”. The Royal Society of Chemistry apologises for these errors and any consequent inconvenience to authors and readers.