Influence of mechanical properties of two resin cements on durability of bond strength to dentin after cyclic loading

The purpose of this study was to evaluate how the different mechanical properties of two luting agents (acrylic resin cement and resin composite cement) influenced their bond strength to dentin, after cyclic loading that simulated chewing. Stainless steel rods were bonded to the flattened dentin surfaces with each luting agent. After immersion in water for 24 hours, half the specimens of each group were tested for tensile bond strength and the remaining half were subjected to a vertical load (75.6 N, 1.2 Hz) using an acrylic stylus--which upon contact with the specimen would rotate counterclockwise and then counter-rotate. Bond strength of the resin composite cement with self-etching was found to be significantly lower than the other adhesive systems. After 100,000 cycles, the bond strength of resin composite cement was significantly decreased while acrylic resin cement showed no decrease in bond strength.     

Evaluation of 2 thione primers and 3 resin adhesives for silver-palladium-copper-gold alloy bonding.

OBJECTIVE: The purpose of this study was to evaluate 2 thione primers and 3 resin adhesives for enhancement of bonding strength to a silver-palladium-copper-gold alloy. METHOD AND MATERIALS: Two different sized disk specimens (10- and 8-mm diameter by 2.5-mm thick) were prepared from a silver-palladium-copper-gold alloy (Castwell M.C. 12, GC). The specimens were airborne-particle abraded with 50-microm-grain alumina, conditioned either with a thiouracil primer (Metaltite, Tokuyama Dental) or with a triazine dithione primer (V-Primer, Sun Medical), and then bonded with 1 of 3 acrylic resins: a benzoyl peroxide-amine redox-initiated resin adhesive (Multi-Bond, Tokuyama Dental) or a tri-nbutylborane-initiated resin adhesive (Super-Bond C&B and Super-Bond Quick, Sun Medical). For each adhesive, unprimed specimens were prepared as experimental controls. Shear bond strength was determined after thermocycling (100,000 cycles). RESULTS: Use of primers significantly (P < .05) enhanced the bond strength of specimens in all adhesives. Irrespective of the type of primer, the strength of Multi-Bond adhesive was significantly (P < .05) lower than that of Super-Bond C&B and Super-Bond Quick adhesives. The strength of the 2 tri-n-butylborane-initiated adhesives did not differ significantly (P > .05). The mean strength of the Super-Bond C&B adhesive was 40.4 MPa with Metaltite and 37.8 MPa with V-Primer; that of Super-Bond Quick adhesive was 40.9 MPa with Metaltite and 36.5 MPa with V-Primer. CONCLUSION: Use of thione primers effectively enhanced the strength of the bond to the silver-palladium-copper-gold alloy. Furthermore, the combinations of primers and tri-n-butylborane-initiated adhesives were found to be more efficient for bonding.     

Clinical Implications of t(11;14) in Patients with Multiple Myeloma Undergoing Autologous Stem Cell Transplantation

Conventional cytogenetic analyses and fluorescent in situ hybridization (FISH) are helpful for stratifying patients with multiple myeloma (MM) into high-risk [t(4;14), t(14;16), and/or del 17p] and standard-risk [t(11;14)] categories. However, the prognosis of patients with MM treated with autologous stem cell transplantation (ASCT) stratified according to these categories remains unclear. This retrospective observational study analyzed 97 patients with MM who received a single, planned ASCT after treatment with 200 mg/m² melphalan between 2001 and 2011. The patients were grouped according to chromosomal abnormality, including t(11;14) (n?=?45), t(4;14) (n?=?31), del 17p (n?=?10), t(11;14) with del 17p (n?=?7), and t(4;14) with del 17p (n?=?4). Median overall survival (OS) of the t(11;14) group (64.1 months) was not significantly different from that of the t(4;14) group (not reached), but it was significantly longer than that of the del 17p group (23.0 months; P?=?.002). G-banding revealed that the median OS of the t(11;14) group with additional chromosomal abnormalities (ACAs) (46.2 months) was significantly shorter than that of the t(11;14) group without ACAs (not reached; P?=?.005) and the t(4;14) group (not reached; P?=?.010). These findings highlight the importance of G-banding in patients with t(11;14) MM.     

Bond strength between luting materials and a fiber-reinforced resin composite for indirect restorations

The purpose of the present study was to evaluate the bond strength between a fiber-reinforced composite (FRC) and six luting agents (Panavia F 2.0, Linkmax MC, Chemiace II, Multibond, Super-Bond C&B, and Fuji I). A prosthodontic resin composite material (RC-control) and a luting agent containing no functional monomer (MT) were used as controls. Shear bond strengths between alumina-blasted FRC and the luting agents were determined after 20,000 thermocycles. The FRC showed superior bond strength when compared with the RC-control. Highest bond strengths were achieved when FRC was bonded with Panavia F 2.0, Linkmax MC, Multibond, Super-Bond C&B, and MT, whereas Chemiace II trailed in the list of resin-based luting agents evaluated. Insufficient bonding was obtained with Fuji I. Results of the present study revealed that when fabricating restorations, the clinician should select an appropriate combination of resin composite material and luting agent so as to ensure the longevity of restorations.     

Effectiveness of polymerization of a prosthetic composite using three polymerization systems.

STATEMENT OF PROBLEM: Although properties of laboratory-polymerized composite materials are influenced by the type of polymerizing unit, little information is available regarding the comparison between use of a high-intensity light source and application of secondary heat treatment. PURPOSE: This study examined properties of a prosthetic veneering composite polymerized with 3 polymerizing systems to evaluate the effects of varying polymerization modes on hardness, solubility, and depth of cure. MATERIAL AND METHODS: A composite material designed for a prosthetic veneer (Conquest Crown and Bridge) was polymerized using 3 methods: (1) exposure in the proprietary photopolymerizing unit with 2 halogen lamps (Cure-Lite Plus), followed by heating in an oven (Conquest Automatic Curing Unit); (2) exposure in a photopolymerizing unit with a xenon stroboscopic light source (Dentacolor XS); and (3) exposure in a photopolymerizing unit with 2 metal halide lamps (Hyper LII). Knoop hardness, water solubility, and depth of cure were determined for groups of 5 specimens, according to standardized testing methods. Data were compared using analysis of variance and the Duncan new multiple range test (P <.05). RESULT: The hardness number generated with the metal halide unit was statistically greater than those produced by the other 2 methods, and material component released into water was minimal when the material was exposed with the metal halide unit (P <.05). Among the 3 photopolymerizing units, the metal halide unit consistently exhibited the greatest depth of cure. CONCLUSION: Certain properties generated with the use of the high-intensity polymerizing unit exceeded those obtained from a proprietary system that requires a postheat treatment.     

A case of tracheal fistula after operation for esophageal cancer]

We have experienced a case of mediastinal abscess and tracheal fistula after operation for esophageal cancer and successfully closed by using intercostal muscle pedicle flap. A 61-year-old male underwent esophagectomy for advanced esophageal cancer. On the 12th postoperative day, mediastinal abscess caused by leakage was detected, and drainage of the mediastinal and thoracic cavity was performed. On the 29th postoperative day, tracheal fistula was detected, and operation was performed in order to close the fistula by using of intercostal muscle pedicle flap. His postoperative course was fair and general condition was improvement, esophageal reconstruction using of free jejunal graft was performed and oral ingestion was started.     

Impact of total body irradiation on successful neutrophil engraftment in unrelated bone marrow or cord blood transplantation

Total body irradiation (TBI) has been thought to promote donor cell engraftment in allogeneic hematopoietic cell transplantation (HCT) from alternative donors. However, recent progress in HCT strategies may affect the clinical significance of TBI on neutrophil engraftment. With the use of a Japanese transplant registry database, we analyzed 3933 adult recipients (>15 y.o.) who underwent HCT between 2006 and 2013 from an 8/8 HLA‐matched unrelated bone marrow donor (MUD, n = 1367), an HLA‐mismatched unrelated bone marrow donor (MMUD, n = 1102), or unrelated cord blood (CBT, n = 1464). Conditioning regimens were divided into five groups: High‐TBI‐(>8Gy), Low‐TBI‐ (≤8Gy), and no‐TBI‐myeloablative conditioning (MAC), and Low‐TBI‐ and no‐TBI‐reduced‐intensity conditioning (RIC). In both MUD and MMUD, neutrophil engraftment rate was >90% in each of the five conditioning groups, and TBI was not associated with prompt neutrophil engraftment in multivariate analyses. Conversely, in CBT, TBI regimens had a higher rate of day‐30 neutrophil engraftment than no‐TBI‐regimens: 78% in High‐TBI‐MAC, 83% in Low‐TBI‐MAC, and 76% in Low‐TBI‐RIC versus 65% in No‐TBI‐MAC, and 68% in No‐TBI‐RIC (P < .001). Multivariate analyses in CBT demonstrated that TBI‐regimens were significantly associated with a higher rate of neutrophil engraftment. Subsequently focusing on CBT patients alone, TBI‐regimens were significantly associated with a higher rate of neutrophil engraftment in patients who received CBT with a 4/6 or less HLA allele‐match, or who had anti‐HLA antibodies. In summary, TBI‐regimens had no impact on neutrophil engraftment in the current practice of unrelated bone marrow transplantation. However, in CBT, TBI is still necessary to enhance engraftment.