Nonextraction treatment with rapid maxillary expansion and mandibular symphyseal distraction osteogenesis and vertical skeletal dimensions

OBJECTIVE: To investigate the effects of rapid maxillary expansion (RME) and mandibular symphyseal distraction osteogenesis (MSDO) on vertical dimensions of the face. MATERIALS AND METHODS: Fourteen patients, nine girls and five boys, underwent RME and MSDO procedures. Distraction was carried out at a rate of 1 mm per 24 hours with a tooth-borne appliance. The amount of distraction was 7 mm for each patient. Standardized lateral cephalograms were taken at the following time periods: before treatment (T0), after RME (T1), at the completion of MSDO (T2), and at the end of fixed orthodontic treatment (T3). The data were evaluated by using a general linear model of repeated-measures analysis of variance and paired t-tests at the 95% confidence level. RESULTS: RME significantly increased the vertical dimensions of the face and decreased the overbite (P < .001). Although the vertical parameters of the face on the lateral cephalogram decreased after MSDO, these decreasing effects were statistically insignificant just for the distances measured from the horizontal reference line to the chin points. In other words, MSDO decreased the vertical skeletal dimensions that were increased by RME, but this neutralizing effect of MSDO was not as much as the increase caused by RME. CONCLUSION: Treatment modalities (RME, MSDO, and fixed orthodontic treatment) described in this study, in total, had little effect on the vertical skeletal measurements of the face.     

The effect of simulated intrapulpal pressure on bond strength to enamel and dentine

The purpose of this study was to evaluate the effect of simulated intrapulpal pressure on the shear bond strength (SBS) of a self-etching bonding system (Clearfil Liner Bond II) to both enamel and dentine surfaces. Forty-two caries-free human molar teeth were randomly assigned to two equal groups (n=21). One group of 21 teeth was connected to a special pulpal pressure machine, which is developed to simulate in vivo conditions. The buccal and lingual surfaces of the teeth were prepared with a diamond wheel to create flat dentine and enamel surfaces. A self-etching bonding system was then applied under pulpal pressure and 2.5 mm diameter composite cylinders were bonded to the prepared surfaces. The samples were then stored in distilled water at room temperature for 24 h under pulpal pressure before SBS was tested. The second restored group was used as a control and the teeth were not connected to the pulpal pressure apparatus during material application and test procedures. They were stored for 24 h in distilled water at room temperature before the SBS test. Fracture analysis of the enamel and dentinal surfaces was performed using a stereomicroscope. Shear bond strength values to dentine was significantly reduced with pulpal pressure (P < 0.001). However, in the enamel, SBS was increased (P < 0.001). In the control group, the SBS values to dentine and enamel did not show any significant difference (P > 0.05). Based on these results, it can be concluded that further analysis of enamel histology and bonding mechanisms are needed.     

Evaluation of internal adaptation in ceramic and composite resin inlays by silicon replica technique

This study was aimed at investigating the internal adaptation of a ceramic (Ceramco II) and two composite resin inlay materials (SureFil and 3M Filtek Z 250) using silicon replica technique as an indicator. Forty-five standard mesial-occlusal-distal (MOD) cavities were prepared into brass moulds by using computer numerically controlled system. Inlays were prepared according to manufacturers' instructions with indirect methods. Replicas of the prepared cavities and inlays were produced with a polyvinyl siloxane material (Elite H-D). The spaces between inlays and cavities were filled by different coloured light-body polyvinyl siloxane material. Two parallel slices (mesio-distally) were obtained from the replicas with a sharp blade. Different coloured polyvinyl siloxane material thickness between cavity and inlay was measured at seven points (mesial, occlusal and distal). The data were evaluated with anova and Tukey's honestly significantly different (HSD) statistical tests. In the SureFil and Ceramco II groups, the sizes of the contraction gaps at mesial and distal gingival floors were greater than that of the occlusal marginal walls. In comparison of gap formation at occlusal regions, while the 3M composite group showed highest gap values (204.33 +/- 75.45 microm), the Ceramco II group revealed the lowest (141.17 +/- 23.66 microm) (P < 0.05). At the gingival floors, gap formation of Ceramco II group was the highest (227.08 +/- 51.95 microm). Neither the 3M Filtek Z250 nor SureFil group showed any statistical difference between gap values of their self-occlusal and gingival floors (P > 0.05). In conclusion, our results showed that ceramic inlays did not confer any big advantage for internal adaptation over the composite inlays.     

Restoring function and esthetics in a patient with amelogenesis imperfecta: a case report.

Amelogenesis imperfecta is a hereditary disorder that affects enamel on primary and permanent teeth. It is a rare dental disease but represents a major restorative challenge for the dentist. A 14-year-old boy presented with sensitive, discolored, and mutilated teeth and a decreased vertical dimension of occlusion. The aim of treatment was to reduce dental sensitivity, to restore esthetics, and to correct the vertical dimension of occlusion. To modify the occlusion, and to protect the dentin from chemical and thermal attacks, nickel-chrome onlays were placed on the molars. To improve the esthetics of the incisors and premolars, resin composite restorations were applied. The patient was regularly recalled during the postoperative period. Radiographic and clinical examinations 10 months posttreatment revealed no evidence of disorders associated with the restored teeth or their supporting structures.