Reactive coupling of poly(ethylene glycol) on electroactive polyaniline films for reduction in protein adsorption and platelet adhesion.

Poly(ethylene glycol) (PEG)-coupled polyaniline (PANI) film surfaces were prepared by incorporating the chlorinie end-capped methoxy PEG (mPEGCl) of molecular weight of about 2000 onto the emeraldine (EM) base form of PANI via N-alkylation. The microstructure and composition of the mPEG-coupled PANI (mPEG-c-PANI) surfaces were characterized by atomic force microscopy, contact angle measurement and X-ray photoelectron spectroscopy. The concentration of surface-coupled mPEG increased with the increase in concentration of the mPEGCl solution. The mPEG-c-PANI film surfaces exhibited enhanced ability to repel protein adsorption, with only an moderate reduction in their electrical conductivity. The mPEG-c-PANI surface with a high concentration of coupled mPEG also exhibited good resistance towards platelet adhesion.     

Bioinspired mineralization and cell adhesion on surface functionalized poly(vinyl alcohol) films

Poly(vinyl alcohol) (PVA) films, when surface functionalized by phosphorylation, induced biomimetic nucleation and growth of calcium phosphate in a simulated physiological environment. The surface phosphorylation on PVA was ensured by attenuated total reflectance infrared spectroscopy. The morphology of the calcium phosphate phase grown on surface-phosphorylated PVA (PPVA) was analysed using scanning electron microscopy coupled with an energy-dispersive X-ray detector. The primary nucleation of calcium phosphate occurs in 3 days and secondary nucleation occurs after 10 days. The energy-dispersive X-ray analysis shows that the Ca/P ratio of the coating increases with time of exposure to the simulated physiological fluid and reaches 1.67 at 10 days. The PPVA supports in vitro cell adhesion and promotes in vitro biomineralization in the presence of cells, evaluated using human osteosarcoma cells.     

Grafting reactions and heparin adsorption of poly(amidoamine)-grafted poly(urethane amide)s.

Differently terminated poly(amidoamine) (PAA) oligomers were grafted on the surface of poly(ether urethane amide)s (PEUAm), with fumaric or maleic acid moieties. The grafting reaction was Michael-type addition of amino groups to activated double bonds in the PEUAm backbone. PAAs having primary amino, or secondary amino end-groups were directly grafted on the surface of PEUAm sheets. For vinyl-terminated chains an alpha, omega amino-polyether spacer was introduced initially, following the same addition mechanism. Ungrafted and grafted materials were characterized, besides other analytical techniques, by ATR FT-IR spectroscopy. The heparin adsorption on PEAUm films was analysed after its elution from heparinized samples, quantified by coagulation tests (aPTT), and related to the presence of the PAAs chains grafted on to the surface. Results indicate that PAA-grafted PEUAm elastomeric biomaterials, display enhanced heparin adsorption abilities.     

Surface modification of poly(tetrafluoroethylene) films via grafting of poly(ethylene glycol) for reduction in protein adsorption

Poly(tetrafluoroethylene) (PTFE) films with surface grafted poly(ethylene glycol) (PEG) chains were prepared by two methods: (1) UV-induced graft copolymerization of methoxy poly- (ethylene glycol) monomethacrylate (PEGMA) onto the plasma-pretreated PTFE films; and (2) coupling of the hydroxyl groups of PEG via ester linkages with the carbonyl chloride groups which were introduced onto the acrylic acid (AAc) graft-copolymerized PTFE surface through reaction with thionyl chloride (SOCl2). The UV-induced graft copolymerization of PEGMA onto the plasma-pretreated PTFE film was explored with different macromonomer concentrations and different UV graft copolymerization time. The coupling reaction, on the other hand, was explored with PEG of different molecular weights. The surface microstructures and compositions of the PEG-modified PTFE films from both processes were characterized by contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) measurements. In general, higher macromonomer concentration and longer UV graft copolymerization time led to a higher graft yield for the UV-induced graft copolymerization with PEGMA. Contact angle measurements revealed that the hydrophilicity of the PTFE film surface was greatly enhanced by the grafting of the PEG chains. The PTFE surface with a high density of grafted PEG was very effective in preventing bovine serum albumin adsorption.     

Mechanism(s) of increased vascular cell adhesion on nanostructured poly(lactic-co-glycolic acid) films

Studies have shown that poly(lactic-co-glycolic acid) (PLGA) films with nanometer surface features promote vascular endothelial and smooth muscle cell adhesion. The objective of this in vitro research was to begin to understand the mechanisms behind this observed increase in vascular cell adhesion. Results provided evidence that nanostructured PLGA adsorbed significantly more vitronectin and fibronectin from serum compared to conventional (or those not possessing nanometer surface features) PLGA. When separately preadsorbing both vitronectin and fibronectin, increased vascular smooth muscle and endothelial cell density was observed on nanostructured (compared to conventional) PLGA. Additionally, blocking of cell-binding epitopes of fibronectin and vitronectin significantly decreased vascular cell adhesion on nanostructured (compared to conventional) PLGA. For this reason, results of the present in vitro study demonstrated that cell adhesive proteins adsorbed in different quantities and altered bioactivity on nanostructured compared to conventional PLGA topographies, which (at least in part) may account for the documented increased vascular cell adhesion on nanostructured PLGA. In this manner, this study continues to provide evidence for the promise of nanostructured PLGA in vascular tissue engineering applications.     

Surface modification of poly(tetrafluoroethylene) films via grafting of poly(ethylene glycol) for reduction in protein adsorption

Poly(tetrafluoroethylene) (PTFE) films with surface grafted poly(ethylene glycol) (PEG) chains were prepared by two methods: (1) UV-induced graft copolymerization of methoxy poly(ethylene glycol) monomethacrylate (PEGMA) onto the plasma-pretreated PTFE films; and (2) coupling of the hydroxyl groups of PEG via ester linkages with the carbonyl chloride groups which were introduced onto the acrylic acid (AAc) graft-copolymerized PTFE surface through reaction with thionyl chloride (SOCl₂). The UV-induced graft copolymerization of PEGMA onto the plasma-pretreated PTFE film was explored with different macromonomer concentrations and different UV graft copolymerization time. The coupling reaction, on the other hand, was explored with PEG of different molecular weights. The surface microstructures and compositions of the PEGmodified PTFE films from both processes were characterized by contact angle, X-ray photoelectron spectroscopy (XPS), and atomic force microscopy (AFM) measurements. In general, higher macromonomer concentration and longer UV graft copolymerization time led to a higher graft yield for the UV-induced graft copolymerization with PEGMA. Contact angle measurements revealed that the hydrophilicity of the PTFE film surface was greatly enhanced by the grafting of the PEG chains. The PTFE surface with a high density of grafted PEG was very effective in preventing bovine serum albumin adsorption.     

Modification of gold surface by grafting of poly(ethylene glycol) for reduction in protein adsorption and platelet adhesion

Gold surfaces were first treated in an alkanethiol solution to form self-assembled monolayers (SAMs). The thiolated Au surface was then subjected to Ar plasma pretreatment, followed by air exposure and UV-induced graft polymerization of poly(ethylene glycol) methacrylate (PEGMA) macromonomer. In comparison with the 3-mercaptopropionic acid-2-ethylhexyl ester (MPAEE) SAM, the (3-mercaptoproply)trimethoxysilane (MPTMS) SAM on Au exhibited higher stability under the conditions of Ar plasma pretreatment. The graft concentration of the PEGMA polymer on SAM-modified Au surface increased with increasing PEGMA macromonomer concentration and UV-graft polymerization time. The modified-Au surfaces were characterized by X-ray spectroscopy (XPS), atomic force microscopy (AFM), and water contact angle measurement. The Au surface with a high concentration of grafted PEGMA polymer could completely repel protein adsorption and platelet adhesion.     

Modification of gold surface by grafting of poly(ethylene glycol) for reduction in protein adsorption and platelet adhesion

Gold surfaces were first treated in an alkanethiol solution to form self-assembled monolayers (SAMs). The thiolated Au surface was then subjected to Ar plasma pretreatment, followed by air exposure and UV-induced graft polymerization of poly(ethylene glycol) methacrylate (PEGMA) macromonomer. In comparison with the 3-mercaptopropionic acid-2-ethylhexyl ester (MPAEE) SAM, the (3-mercaptoproply)trimethoxysilane (MPTMS) SAM on Au exhibited higher stability under the conditions of Ar plasma pretreatment. The graft concentration of the PEGMA polymer on SAMmodified Au surface increased with increasing PEGMA macromonomer concentration and UV-graft polymerization time. The modified-Au surfaces were characterized by X-ray spectroscopy (XPS), atomic force microscopy (AFM), and water contact angle measurement. The Au surface with a high concentration of grafted PEGMA polymer could completely repel protein adsorption and platelet adhesion.     

Modification of Si(100) surface by the grafting of poly(ethylene glycol) for reduction in protein adsorption and platelet adhesion

The modification of argon plasma-pretreated single-crystal Si(100) wafer surfaces via the UV-induced graft polymerization of poly(ethylene glycol) methacrylate (PEGMA) macromonomer (molecular weight approximately 340) for biomaterials applications was explored. The modified Si(100) surfaces were characterized by X-ray photoelectron spectroscopy and atomic force microscopy. Surface peroxide concentrations resulting from the argon plasma treatment and subsequent atmospheric exposure were determined by a coupling reaction with diphenylpicrylhydrazyl. The results suggested that a short plasma treatment time of 10 s and brief air exposure were sufficient for generating an optimum amount of peroxides and hydroperoxides for the subsequent UV-induced graft polymerization. The graft concentration of the PEGMA polymer increased with increasing PEGMA macromonomer concentration for the graft polymerization and with increasing UV graft polymerization time. The PEGMA graft-polymerized silicon surface with a high poly(ethylene glycol) graft concentration was very effective in preventing protein adsorption and platelet adhesion. The grafted PEGMA polymer layer on the Si(100) surface exhibited fairly good stability during storage in a buffer solution.     

Protein adsorption and smooth muscle cell adhesion on biodegradable agmatine-modified poly(propylene fumarate-co-ethylene glycol) hydrogels

We synthesized positively charged biodegradable hydrogels from poly(propylene fumarate-co-ethylene glycol) block copolymer and agmatine-modified poly(ethylene glycol)-tethered fumarate by radical crosslinking, and investigated the effect of the guanidino group of agmatine on vascular smooth muscle cell adhesion and protein adsorption to the hydrogels. In the presence of serum, the number of adherent smooth muscle cells per unit surface area increased dose-dependently from 15 to 75% of the initial seeding density at 20 h as the initial agmatine-modified monomer content increased from 0 to 200 mg/g. Cell spreading also depended on the initial monomer content. In the absence of serum, the number of adherent cells per unit surface area increased slightly from 10 to 17% of the initial seeding density as the initial monomer content increased from 0 to 200 mg/g. Cell adhesion increased significantly by adding exogenous vitronectin to serum-free medium, whereas exogenous fibronectin addition did not enhance cell adhesion. The enzyme-linked immunosorbent assay of fibronectin and vitronectin adsorbed onto the hydrogels revealed that the incorporation of positive charges into the hydrogels enhanced vitronectin, but not fibronectin, adsorption significantly. These results suggest that the guanidino group of agmatine enhanced cell adhesion by promoting the adsorption of serum components, and vitronectin may be one of the components.     

Blood compatible aspects of poly(2-methoxyethylacrylate) (PMEA)--relationship between protein adsorption and platelet adhesion on PMEA surface

Platelet adhesion and spreading is suppressed when a poly(2-methoxyethylacrylate) (PMEA) surface is used, compared with other polymer surfaces. To clarify the reason for this suppression, the relationship among the amount of the plasma protein adsorbed onto PMEA, its secondary structure and platelet adhesion was investigated. Poly(2-hydroxyethylmethacrylate) (PHEMA) and polyacrylate analogous were used as references. The amount of protein adsorbed onto PMEA was very low and similar to that absorbed onto PHEMA. Circular dichroism (CD) spectroscopy was applied to examine changes in the secondary structure of the proteins after adsorption onto the polymer surface. The conformation of the proteins adsorbed onto PHEMA changed considerably, but that of proteins adsorbed onto PMEA differed only a little from the native one. These results suggest that low platelet adhesion and spreading are closely related to the low degree of the denaturation of the protein adsorbed onto PMEA. PMEA could be developed as a promising material to produce a useful blood-contacting surface for medical devices.     

Hydrogels based on poly(ethylene oxide) and poly(tetramethylene oxide) or poly(dimethyl siloxane): synthesis, characterization, in vitro protein adsorption and platelet adhesion

In vitro protein adsorption, platelet adhesion and activation on new hydrogel surfaces, composed of poly(ethylene oxide) (PEO) and poly(tetramethylene oxide) (PTMO) or poly(dimethyl siloxane) (PDMS), were investigated. By varying PEO length (MW = 2000 or 3400), hydrophobic components (PTMO or PDMS) or polymer topology (block or graft copolymers), various physical hydrogels were produced. Their structures were verified by 1H NMR and ATR-IR and the molecular weights were determined by gel permeation chromatography. The hydrogels were soluble in a variety of organic solvents, while absorbed a significant amount of water with preserved three-dimensional structure by physical crosslinking. The dynamic contact angle measurement revealed that the surface hydrophilicity increased by incorporating longer PEO, PEO grafting, and adopting PDMS as a hydrophobic segment instead of PTMO. It was observed from in vitro protein adsorption study that the hydrogels exhibited significantly lower adsorption of human serum albumin (HSA), human fibrinogen (HFg), and IgG, when compared with Pellethane, a commercial polyurethane taken as a control. The hydrogels were attractive for HSA but not sensitive to HFg and IgG. And more than 65% of the proteins detected on the surfaces of the hydrogels were reversibly detached by being treated with an SDS solution. It was evident that the hydrogels synthesized in this study were much more resistant to platelet adhesion than the control, which might depend on the composition of proteins adsorbed on the surfaces and their degree of denaturation. Among the hydrogels tested, PEO3,4kPDMS exhibited albumin-rich and platelet-resistant surfaces, implying a potential candidate for biomaterial.     

Surface modification of poly(hydroxybutyrate) films to control cell-matrix adhesion

Tailoring surface properties of degradable polymer scaffolds is key to progress in various tissue engineering strategies. Poly(3-hydroxybutyrate) and poly(3-hydroxybutyrate-co-4-hydroxybutyrate) thin films were modified by low pressure ammonia plasma, low pressure water vapour plasma, or immersion in a sodium hydroxide solution to elaborate means to control the cell-matrix adhesion of human umbilical cord vein endothelial cells grown on these materials. Fibronectin (FN) heteroexchange and cell adhesion were correlated to the physicochemical characteristics of the modified polymer surfaces which were investigated by X-ray photoelectron spectroscopy (XPS), scanning force microscopy (SFM), electrokinetic measurements, and contact angle measurements. All treatments increased the hydrophilicity of the polymer samples, which could be accounted to newly created amine or carboxyl functionalities for ammonia plasma or water vapour plasma treatments, respectively, and ester hydrolysis for treatments with alkaline aqueous solutions. Main features of cell adhesion and FN reorganisation-evaluated after 1h and after 5 days-could be attributed to the anchorage strength of pre-coated FN layers at the polymer surface, which was, in turn found to be triggered by the type of modification applied. In line with earlier studies referring to different materials cell adhesion and matrix reorganisation were shown to be sensitively controlled through the physicochemical profile of poly(hydroxybutyrate) surfaces.     

Protein adsorption and cell adhesion on nanoscale bioactive coatings formed from poly(ethylene glycol) and albumin microgels

Late-term thrombosis on drug-eluting stents is an emerging problem that might be addressed using extremely thin, biologically active hydrogel coatings. We report a dip-coating strategy to covalently link poly(ethylene glycol) (PEG) to substrates, producing coatings with 100nm thickness. Gelation of PEG-octavinylsulfone with amines in either bovine serum albumin (BSA) or PEG-octaamine was monitored by dynamic light scattering (DLS), revealing the presence of microgels before macrogelation. NMR also revealed extremely high end-group conversions prior to macrogelation, consistent with the formation of highly crosslinked microgels and deviation from Flory-Stockmayer theory. Before macrogelation, the reacting solutions were diluted and incubated with nucleophile-functionalized surfaces. Using optical waveguide lightmode spectroscopy (OWLS) and quartz crystal microbalance with dissipation (QCM-D), we identified a highly hydrated, protein-resistant layer with a thickness of approximately 75nm. Atomic force microscopy in buffered water revealed the presence of coalesced spheres of various sizes but with diameters less than about 100nm. Microgel-coated glass or poly(ethylene terephthalate) exhibited reduced protein adsorption and cell adhesion. Cellular interactions with the surface could be controlled by using different proteins to cap unreacted vinylsulfone groups within the coating.     

Control of cell adhesion on poly(methyl methacrylate)

Keratoprostheses have been constructed from a wide variety of transparent materials, including poly(methyl methacrylate) (PMMA). However, the success of keratoprosthesis has been plagued by numerous shortcomings that include the weakening of the implant-host interface due to weak cell adhesion and opaque fibrous membrane formation over the inner surface of the implant due to fibroblast attachment. An effective solution requires a surface modification that would selectively allow enhanced cell attachment at the implant-host interface and reduced cell attachment over the interior surface of the implant. Here, we have developed a novel and simple peptide conjugation scheme to modify PMMA surfaces, which allowed for region-specific control of cell adhesion. This method uses di-amino-PEG, which can be grafted onto PMMA using hydrolysis or aminolysis method. PEG can resist cell adhesion and protein adsorption. The functionalization of grafted di-amino-PEG molecules with RGD peptide not only restored cell adhesion to the surfaces, but also enhanced cell attachment and spreading as compared to untreated PMMA surfaces. Long-term cell migration and micropatterning studies clearly indicated that PEG-PMMA surfaces with and without RGD conjugation can be used to differentiate cell adhesion and control cell attachment spatially on PMMA, which will have potential applications in the modification of keratoprostheses.     

Improvement of cell adhesion on poly(L-lactide) by atmospheric plasma treatment

The purpose of this study is to elucidate the interaction between the cell and the surface of poly(L-lactide) (PLLA) samples, which were modified using a low-temperature plasma treatment apparatus at atmospheric pressure. The plasma treatments were carried out in the atmospheres of air, carbon dioxide (CO2), and perfluoro propane (C3F8) gas. The PLLA samples before and after the plasma treatment were analyzed by XPS and their contact angles with water. Furthermore, the cell adhesion capability and cell mass culturing tests on the PLLA samples were carried out using MC3T3-E1 cells. The results showed that the contact angle of the samples, which was plasma treated in air or in CO2 gas, decreased compared with that of the untreated samples. On the other hand, the contact angle of the samples, which was plasma treated in the C3F8 gas, increased compared with the untreated plasma samples. The cell response on the PLLA samples plasma treated in air or in the CO2 gas were significantly superior to that of the PLLA samples, which was plasma treated in the C3F8 gas.     

pH-dependent modulation of fibroblast adhesion on multilayers composed of poly(ethylene imine) and heparin

Adhesion of tissue cells is a prerequisite for their growth and differentiation but prevents also apoptosis. Here the layer-by-layer technique (LbL) was used to design multilayer structures of poly(ethylene imine) (PEI) and heparin (HEP) on glass as model biomaterial to control the adhesion of primary human dermal fibroblasts. Distinct surface features like wettability, charge and lateral structures were controlled by changing the pH value of the HEP solution during multilayer assembly to acidic, neutral or alkaline values. While plain terminal layers were rather cytophobic, the pre-adsorption of serum or fibronectin (FN) caused a distinct change in cell morphology in dependence on the pH setup. The effect of serum was more prominent on PEI layers probably due to their positive surface charge, whereas the effect of FN was more pronounced on HEP terminated multilayers possibly due to its ability to bind FN specifically. Those layers which hampered cell adhesion also inhibited growth of human fibroblasts under serum conditions. Conversely, on layers where cell adhesion was increased also an elevated growth and, thus, metabolic activity was observed.     

Permeation of protein from porous poly(epsilon-caprolactone) films

The objective of this study was designed to extend the application of poly(epsilon-caprolactone) (PCL) in delivery of macromolecular proteins. The strategy applied here is to create a porous structure in PCL films in order to control the diffusion rate of protein. Various amounts of both high-molecular-weight and low-molecular-weight poly(ethylene glycol) (PEG) were used as pore-forming agents. The porous films were prepared by a solvent-casting-leaching method. The thicknesses of the prepared films were controlled to be in the range of 75.3 +/- 0.6 similar 81.7 +/- 0.6 mum. The pore fraction of films was determined to be 27.7 +/- 1.0% similar 52.5 +/- 0.8% for PEG(10000) and 26.6 +/- 1.8% similar 48.8 +/- 1.4% for PEG(4000). The pore fraction initially increased with increasing amounts of PEG, independent of the molecular weight of PEG. In the permeation study, lysozyme was used as a model diffuser. The permeation rate of protein increased as the pore fraction of films increased, especially when 30 similar 40% of PEG was added initially, and this phenomenon was more prominent when low-molecular-weight PEG was used. This result was probably due to the highly porous structure creating interconnected channels in the films, further enhancing protein diffusion. In addition, the size of micropores formed by PEG(4000) was observed to be larger than by PEG(10000), which also accounted for faster permeation rate of lysozyme through PCL-PEG(4000) porous films.     

Plasma protein adsorption pattern and tissue-implant reaction of poly(vinyl alcohol)/carboxymethyl-chitosan blend films

Various poly(vinyl alcohol)/carboxymethyl-chitosan (PVA/CMCS) blend films were prepared by a mechanical blending method and characterized by SEM for their surface and cross-section morphologies. It indicated that blending high CMCS content in PVA plastic led to a rough surface and loose structure. Bovine serum albumin (BSA) and bovine fibrinogen (BFG) were chosen as representative plasma proteins to carry out adsorption tests. Equilibrium adsorption amount of proteins onto the blends decreased with the increase of CMCS content in film matrix, and BSA was more easily adsorbed onto the films than BFG in the same conditions. The blend films also exhibited different trends for BSA and BFG adsorption when pH of the media changed, but maximum adsorption approximately occurred at the isoelectric point of proteins. Moreover, increasing the ionic strength would always decrease the adsorptions of protein onto the films. In animal experiments, it was found that incorporation of CMCS and PVA gave a lower tissue reaction than pure PVA films when they were subcutaneously implanted in Wistar rats. After two weeks subcutaneous implantation, surfaces of PVA became wrinkled and cracked; however, the blend implants exhibited a alveolate porous microstructure.     

Plasma protein adsorption pattern and tissue-implant reaction of poly(vinyl alcohol)/carboxymethyl-chitosan blend films

Various poly(vinyl alcohol)/carboxymethyl-chitosan (PVA/CMCS) blend films were prepared by a mechanical blending method and characterized by SEM for their surface and cross-section morphologies. It indicated that blending high CMCS content in PVA plastic led to a rough surface and loose structure. Bovine serum albumin (BSA) and bovine fibrinogen (BFG) were chosen as representative plasma proteins to carry out adsorption tests. Equilibrium adsorption amount of proteins onto the blends decreased with the increase of CMCS content in film matrix, and BSA was more easily adsorbed onto the films than BFG in the same conditions. The blend films also exhibited different trends for BSA and BFG adsorption when pH of the media changed, but maximum adsorption approximately occurred at the isoelectric point of proteins. Moreover, increasing the ionic strength would always decrease the adsorptions of protein onto the films. In animal experiments, it was found that incorporation of CMCS and PVA gave a lower tissue reaction than pure PVA films when they were subcutaneously implanted in Wistar rats. After two weeks subcutaneous implantation, surfaces of PVA became wrinkled and cracked; however, the blend implants exhibited a alveolate porous microstructure.