Two narrow bandgap copolymers derived from 6,6′,12,12′‐tetraoctyl‐indeno[1,2‐b]fluorene and bithiophene or thieno[3,2‐b]thiophene‐cored benzothiadiazole are synthesized and characterized. The copolymers show broad absorption in the range 350–700 nm. The application of the copolymers as photovoltaic cells with configurations ITO/PEDOT:PSS/blend/Al and ITO/PEDOT:PSS/blend/interlayer/Al is investigated. A power conversion efficiency (PCE) of approximately 3.0% is achieved under an AM 1.5G solar simulator (80 mW cm?2) for the cells with ITO/PEDOT:PSS/polymer:PC71BM([6,6]‐phenyl‐C71 butyric acid methyl ester) (1:4)/interlayer/Al.
This work describes the effect of sulfuric acid protonation on the properties of SPOD‐DPE membranes using FT‐IR and impedance spectroscopic analyses. The IR spectra showed the protonation of nitrogen atoms from oxadiazole rings, with a broad band complex in the region 3 000–2 100 cm?1 with two centered peaks at 2 590 and 2 440 cm?1. The S?O characteristic absorption bands in SPOD‐DPE and sulfuric acid were specially studied in the region of 1 800–900 cm?1. The band shifts are associated to the interaction between acid groups and oxadiazole ring nitrogen atoms. The IR spectra evidenced the presence of three absorption species (HSO, SO and free H2SO4) depending on the sulfuric acid concentration. For the protonated SPOD‐DPE membranes, a proton conductivity around 10 mS · cm?1 was reached at 50 °C.
CROP has been used to synthesize well‐defined POXZ with a monofunctional (iodomethane) or a bifunctional (1,3‐diiodopropane) initiator. POXZ has been functionalized with an azido group at one (α‐azido‐POXZ, = 3.58 × 103 g · mol?1) or both ends (α,ω‐azido‐POXZ, = 6.21 × 103 g · mol?1) of the macromolecular chain. The Huisgen 1,3‐dipolar cycloaddition has been investigated between azido‐POXZ and a terminal alkyne on a small or larger molecule (PEG). In each case, the click reaction has been successful and quantitative. In this way, different telechelic polymers (polymers bearing different functions such as acrylate, epoxide, or carboxylic acid) and block copolymers of POXZ and PEG have been prepared. The polymers have been characterized by means of FTIR, 1H NMR, and SEC.
A new dithienyl benzotriazole‐based conjugated polymer was synthesized by Suzuki coupling reaction. The polymer was found to be soluble in common organic solvents, such as chloroform, tetrahydrofuran and chlorobenzene, with excellent film‐forming properties. The structure of the polymer was confirmed by 1H NMR, the molecular weights determined by GPC and the thermal properties investigated by TGA and DSC. The polymer films exhibited an absorption band in the wavelength range 300 to 610 nm. Preliminary photovoltaic cells based on the composite structure of indium tin oxide (ITO)/PEDOT:PSS/ PCDTBTz:PC 60 BM (1:2 w/w)/Al showed an open‐circuit voltage of 0.92 V, a power conversion efficiency of 2.2% and a short circuit current of 5.33 mA cm?2.
PANGMA nanofibers and nanomats with fiber diameters of 200–300 nanometers were fabricated by electrospinning. Cal‐B was covalently immobilized onto the PANGMA nanomats via three different immobilization routes. The properties of the Cal‐B‐immobilized PANGMA nanomats were assayed and compared with the free Cal‐B. The observed Cal‐B loading on these nanomats is up to ≈50 mg · g?1, and their hydrolytic activity is up to ≈2 500 nmol · min?1 · mg?1, much higher than free enzyme powder and also slightly higher than Novozyme 435. Cal‐B immobilized PANGMA nanomats have better reusability, thermal stability, and storage ability than free Cal‐B. They retain over 50% of their initial activity after 15 cycles, over 65% after 10 h heat incubation, and over 75% after 30 d storage.
In order to understand the contribution of nanoparticle surface area to the properties of nanocomposite materials, hydroxyapatite nanoparticles with different specific surface areas (60 m2 · g?1 and 111 m2 · g?1) were synthesized using reverse microemulsion and processed into nanocomposites. Experimental results indicated that the thermomechanical reinforcement did show a dependence on nanoparticle surface area, although the transition temperatures did not. The reinforcement trends were dependent on temperature, suggesting that the nanoparticles had a greater impact on the amorphous polymer chains. The reinforcement above Tg may be plotted against nanoparticle surface area to obtain a single reinforcement trend, suggesting that surface area is a general parameter for nanocomposite property control.
Two novel reactive poly(β‐cyanoethylsilsesquioxane) ( CN‐T ) and poly[(β‐cyanoethylsilsesquioxane)‐co‐(β‐methylsilsesquioxane)] ( CN‐Me‐T ) have been synthesized successfully for the first time via stepwise coupling polymerization (SCP). A variety of characterization methods including FTIR, 1H NMR, 29Si NMR, X‐ray diffraction (XRD), differential scanning calorimetry (DSC) and vapor pressure osmometry (VPO) were combined to demonstrate that the structures of the title polymers possess ordered ladder‐like structures. As expected, the ionic conductivity of these polymers mixed homogeneously with lithium perchlorate reached 10?6 S · cm?1 at room temperature and obviously increased with the raise of temperature.
Two new donor/acceptor copolymers PBDTPhBT1 and PBDTPhBT2 with alternating benzodithiophene ( BDT ) and bisthiophene‐phthalimide ( PhBT ) units were synthesized by Stille coupling reaction. The copolymers showed identical optical bandgaps of 1.98 eV. The HOMO energy levels are ?5.35 and ?5.32 eV for PBDTPhBT1 and PBDTPhBT2 , respectively. The bulk heterojunction solar cell devices based on these copolymers as donors and PC71BM as acceptor displayed high open‐circuit voltages of 0.90–0.93 V and achieved power conversion efficiency of 1.54% under the illumination of AM 1.5, 100 mW · cm?2.
pH‐sensitive micelles formed by interchain hydrogen bonding of poly(methacrylic acid)‐block‐poly(ethylene oxide) copolymers were prepared and investigated at pH < 5. Both and Rh of the micelles increase with decreasing pH of the solution, displaying an asymptotic tendency at low pH values. The observed micelles are well‐defined nanoparticles with narrow size distributions (polydispersity ΔRh/Rh ≤ 0.05) comparable with regular diblock copolymer micelles. The CMCs occur slightly below c = 1 × 10?4 g · mL?1. The micelles are negatively charged and their time stability is lower than that of regular copolymer micelles based purely on hydrophobic interactions.
π‐Conjugated polymers composed of dialkoxybenzo[1,2‐b:4,5‐b′]dithiophene and thiophenes bearing cyano‐alkoxycarbonylethenyl [? CH?C(CO2R)CN] and bis(alkoxycarbonyl)ethenyl groups [? CH?C(CO2R)2] were prepared. The optical properties of the obtained polymers were investigated by UV‐vis and photoluminescence spectroscopy to demonstrate that the absorption maxima of the polymers were tunable by varying the substituent of thiophene unit. The photoluminescence wavelengths and intensities of the polymer in solution were significantly dependent on the polymer side chain. The HOMO energy level of the polymer was lowered by up to ?5.51 eV by introducing electron‐deficient cyano groups. Polymer solar cells based on the new polymers were fabricated to achieve a PCE of 1.90%.
Two terthiophenes bearing core fluorinated thienyl units have been synthesised as potential semiconductor materials for organic field‐effect transistors. Polymerisation of these compounds has been achieved using conventional iron(III) chloride oxidative coupling methods and by electrochemical oxidation. Characterisation of the fluorinated materials has been achieved by absorption spectroscopy and cyclic voltammetry. A soluble hexyl‐functionalised polymer (poly 8b ) was used in an OFET device; hole mobilities were measured up to 3 × 10?3 cm2 · V?1 · s?1, and the device had an on/off ratio of 105 and a turn‐on voltage of +4 V.
Summary: N‐Hexyl‐cyclopenta[c]pyrrole was synthesized and electrochemically and chemically polymerized to a novel 1,3,4‐alkyl‐substituted polypyrrole. The polymer was characterized in solution and as thin solid film by cyclic voltammetry, UV‐vis, FTIR and NMR spectroscopy, MALDI mass spectroscopy, GPC analysis, electrochemical quartz crystal microbalance, ESR spectroscopy and in situ conductivity. The polymer, with a defect‐free structure and an average degree of polymerization of 13 (electrochemically prepared) and 24 (chemically prepared), is soluble (>1%) in acetone, acetonitrile and chlorinated solvents. Its in situ conductivity as a function of potential and doping charge has the typical features of redox conductivity with a maximum value of ca 1 × 10?3 S · cm?1.
Structure of poly(N‐hexyl‐cyclopenta[c]pyrrole). 相似文献
Poly(3‐hexylthiophene)‐block‐poly(tetrahydrofuran) was synthesized by cationic ring‐opening polymerization of tetrahydrofuran (THF) using a poly(3‐hexylthiophene) macroinitiator. Poly(3‐hexylthiophene) macroinitiator used for the ring‐opening polymerization of THF was synthesized by reacting the hydroxypropyl end‐group with trifluoromethanesulfonic anhydride in the presence of 2,6‐di‐tert‐butylpyridine. 1H NMR spectroscopy and SEC data confirmed the formation of the di‐block copolymers. Field‐effect mobility of poly(3‐hexylthiophene)‐block‐poly(tetrahydrofuran) was measured in a thin‐film transistor configuration and was found to be 0.009 cm2 · V?1 · s?1.
Biodegradable and photocurable block copolymers of ε‐caprolactone and L ‐lactide were synthesized by polycondensation of PLLA diol ( = 10 000 g · mol?1), PCL diol ( = 10 000 g · mol?1), and a chain extender bearing a coumarin group. The effect of copolymer composition on the thermal and mechanical properties of the photocured copolymers was studied by means of DSC and cyclic tensile tests. An increase in Young's modulus and a decrease in the tensile strain with increasing PLLA content was observed for the block copolymers. Block copolymers with high PCL content showed good to excellent shape‐memory properties. Random copolymers exhibited Rf and Rr values above 90% at 45 °C for an extremely large tensile strain of 1 000%.
Summary: Poly[ethylene‐co‐(butyl acrylate)‐co‐(carbon monoxide)] (polyEBC) samples, prepared from 13C‐labeled carbon monoxide, were characterized using two dimensional (2D) pulsed field gradient (PFG) 750 MHz NMR spectroscopy. To elucidate the complex mixture of structures present in this terpolymer, 2D 1H/13C‐heteronuclear multiple bond correlation (HMBC) experiments were conducted by selectively exciting the enhanced peaks resulting from 13C‐labeling. High resolution 2D NMR combined with 13C‐labeling of the polymer greatly simplifies the 2D NMR spectra, selectively enhances the weak peaks from low occurrence C‐centered triad structures and aids in their resonance assignments.
Poly(4,4‐bis[(3,5‐diethoxybenzoyloxy)methyl]‐1,6‐heptadiyne) is synthesized via cyclopolymerization using modified Grubbs‐ and Schrock‐type initiators. Doping with either I2 or NO+ BF4? yields a conductive polymer with conductivity up to 1.4 × 10?2 S cm?1. The undoped amorphous conjugated polymer is spun into monofilament and multifilament fibers by a wet‐spinning process. Fibers are collected on bobbins with a draw down ratio of 12 resulting in fiber diameters under 60 μm, characterized by scanning electron microscopy. X‐ray diffraction data confirms that the amorphous structure of the polymer is preserved; no additional orientation of the polymer chains occurs during fiber spinning.
Multiarm PEO star polymers with a purely aliphatic polyether structure have been synthesized using hyperbranched polyglycerol (PG) with different molecular weights as a multifunctional initiator. Different degrees of deprotonation of the initiator were studied with respect to molecular weight control. The results show that the degree of deprotonation is a crucial parameter for the synthesis of well‐defined polymers with controlled molecular weights. Partial deprotonation of the PG hydroxyl groups (5–8%) was proven to represent an optimum for the synthesis of star polymers with molecular masses close to the theoretical values. Molecular weights of the stars ranged between 9 000 and 30 000 g · mol?1. MALDI‐ToF spectra confirmed that the PEO arms in the star polymers possess homogeneous lengths.
We synthesized a series of polystyrene derivatives containing coumarin side groups using polymer analogous reactions. The liquid‐crystal (LC) alignment director for these polymer films was found to be perpendicular to the rubbing direction. The contrast ratio and anchoring‐energy values of these polystyrene derivatives were found to be much greater than those of polystyrene and poly(chloromethylstyrene), indicating that the coumarin side groups increase the aligning ability. For example, the anchoring energy of a polymer with 82 mol‐% of coumarin‐containing monomeric units, compared to polystyrene, is about 7 × 10?5 J · m?2 and 1 × 10?7 J · m?2, respectively.
The manipulation of the properties of cycloaliphatic epoxy resins by systematical variations of the molecular structure is demonstrated. Specifically, four cycloaliphatic epoxy resins with silicon‐center linked via methyl, phenyl, and epoxy groups of different number were synthesized. The cured epoxides had remarkably changed crosslinking density from 0.45 × 10?3 to 9.64 × 10?3 mol · cm?3, glass transition temperature from 133 to 237 °C, and considerably decreased thermal expansion coefficient from 6.44 × 10?5 to 4.83 × 10?5 K?1. It was proved that the higher crosslinking density was related to more opened segments by wide‐angle X‐ray diffraction. The physical properties of cured products and their correlations with the chemical structures were investigated in detail.
In the presence of ethylene glycol, poly(ethylene terephthalate) (PET) undergoes chain scissions with the formation of α,ω‐hydroxyl oligomers, through classical transesterification by alcoholysis. ε‐Caprolactone was subsequently added on the hydroxyl end groups of PET oligomers by ring‐opening polymerization at different molar ratios of ε‐caprolactone to PET oligomers. The chemical structure of the products was investigated by size exclusion chromatography, 1H NMR spectroscopy, and differential scanning calorimetry. A large majority of these products are soluble in common organic solvents. The thermal and 1H NMR analyses reveal that the transesterification between base units of PET oligomers and ε‐caprolactone during the synthesis is always present whatever the reaction conditions. This phenomenon leads to copolymers having thermal properties different from those of PET. However, some co‐oligomers present the interest of keeping properties close to those of PET. The main purpose of this study was the synthesis of PET co‐oligomers that are soluble in some organic solvents that would make their use easier, and so that they can be used further as hard segment precursers for polycondensation reactions.
Ring‐opening polymerization of ε‐caprolactone onto hydroxytelechelic oligomers of PET. 相似文献
