Performance Improvement of PVDF–HFP-Based Gel Polymer Electrolyte with the Dopant of Octavinyl-Polyhedral Oligomeric Silsesquioxane

Gel polymer electrolytes have the advantages of both a solid electrolyte and a liquid electrolyte. As a transitional product before which a solid electrolyte can be comprehensively used, gel polymer electrolytes are of great research value. They can reduce the risk of spontaneous combustion and explosion caused by leakage during the use of conventional liquid electrolytes. Poly(vinylidene-fluoride-co-hexafluoropropylene) (PVDF–HFP), a material with excellent performance, has been widely utilized in the preparation of gel polymer electrolytes. Here, PVDF–HFP-based gel polymer membranes with polyvinyl pyrrolidone (PVP) pores were prepared using a phase inversion method, and Octavinyl-polyhedral oligomeric silsesquioxane (OVAPOSS) was doped to improve its temperature resistance as well as its ionic conductivity, to enhance its safety and electrochemical performance. The final prepared polymer membrane had a porosity of 85.06% and still had a certain mechanical strength at 160 °C without any shrinkage. The gel polymer electrolyte prepared with this polymer membrane had an ionic conductivity of 1.62 × 10⁻³ S·cm⁻¹ at 30 °C, as well as an electrochemical window of about 5.5 V. The LiCoO₂-Li button half-cell prepared therefrom had a specific capacity of 141 mAh·g⁻¹ at a rate of 1C. The coulombic efficiency remained above 99% within 100 cycles and the capacity retention rate reached 99.5%, which reveals an excellent cycling stability.     

Comparing Triflate and Hexafluorophosphate Anions of Ionic Liquids in Polymer Electrolytes for Supercapacitor Applications

Two different ionic liquid-based biopolymer electrolyte systems were prepared using a solution casting technique. Corn starch and lithium hexafluorophosphate (LiPF₆) were employed as polymer and salt, respectively. Additionally, two different counteranions of ionic liquids, viz. 1-butyl-3-methylimidazolium hexafluorophosphate (BmImPF₆) and 1-butyl-3-methylimidazolium trifluoromethanesulfonate (also known as 1-butyl-3-methylimidazolium triflate) (BmImTf) were used and studied in this present work. The maximum ionic conductivities of (1.47 ± 0.02) × 10⁻⁴ and (3.21 ± 0.01) × 10⁻⁴ S·cm⁻¹ were achieved with adulteration of 50 wt% of BmImPF₆ and 80 wt% of BmImTf, respectively at ambient temperature. Activated carbon-based electrodes were prepared and used in supercapacitor fabrication. Supercapacitors were then assembled using the most conducting polymer electrolyte from each system. The electrochemical properties of the supercapacitors were then analyzed. The supercapacitor containing the triflate-based biopolymer electrolyte depicted a higher specific capacitance with a wider electrochemical stability window compared to that of the hexafluorophosphate system.     

Co-Precipitation Synthesis of Co3[Fe(CN)6]2·10H2O@rGO Anode Electrode for Lithium-Ion Batteries

Rechargeable lithium-ion batteries (LIBs) are known to be practical and cost-effective devices for storing electric energy. LIBs have a low energy density, which calls for the development of new anode materials. The Prussian blue analog (PBA) is identified as being a candidate electrode material due to its facile synthesis, open framework structures, high specific surface areas, tunable composition, designable topologies and rich redox couples. However, its poor electrical conductivity and mechanical properties are the main factors limiting its use. The present study loaded PBA (Co₃[Fe(CN)₆]·10H₂O) on graphene oxide (Co-Fe-PBA@rGO) and then conducted calcination at 300 °C under the protection of nitrogen, which reduced the crystal water and provided more ion diffusion pathways. As a result, Co-Fe-PBA@rGO showed excellent performance when utilized as an anode in LIBs, and its specific capacities were 546.3 and 333.2 mAh g⁻¹ at 0.1 and 1.0 A g⁻¹, respectively. In addition, the electrode also showed excellent performance in the long-term cycle, and its capacity reached up to 909.7 mAh g⁻¹ at 0.1 A g⁻¹ following 100 cycles.     

Flexible Quasi-Solid-State Composite Electrolyte of Poly (Propylene Glycol)-co-Pentaerythritol Triacry-Late/Li1.5Al0.5Ge1.5(PO4)3 for High-Performance Lithium-Sulfur Battery

With a higher theoretical specific capacity (1675 mAh g⁻¹) and energy density (2600 Wh kg⁻¹), the lithium-sulfur (Li-S) battery is considered as a promising candidate for a next-generation energy storage device. However, the shuttle effect of polysulfides as well as the large interfacial impedance between brittle solid electrolyte and electrodes lead to the capacity of the Li-S battery decaying rapidly, which limits the practical commercial applications of the Li-S battery. Herein, we reported a facile in situ ultraviolet (UV) curing method to prepare a flexible quasi-solid-state composite electrolyte (QSSCE) of poly(propylene glycol)-co-pentaerythritol triacrylate/Li_1.5Al_0.5Ge_1.5(PO₄)₃ (PPG-co-PETA/LAGP). By combining the high Li-ion conductivity and mechanical strength of inorganic NASICON-structure LAGP and good flexibility of the crosslinked PPG-co-PETA with nanopore structure, the flexible QSSCE with 66.85 wt% LAGP exhibited high Li-ion conductivity of 5.95 × 10⁻³ S cm⁻¹ at 25 °C, Li-ion transference number of 0.83 and wide electrochemical window of ~5.0 V (vs. Li/Li⁺). In addition, the application of QSSCE in the Li-S battery could suppress the shuttle effect of polysulfides effectively, thus the Li-S battery possessed the excellent electrochemical cyclic performance, showing the first-cycle discharge-specific capacity of 1508.1 mAh g⁻¹, the capacity retention of 73.6% after 200 cycles with 0.25 C at 25 °C and good rate performance.     

Modified Activation Process for Supercapacitor Electrode Materials from African Maize Cob

In this work, African maize cobs (AMC) were used as a rich biomass precursor to synthesize carbon material through a chemical activation process for application in electrochemical energy storage devices. The carbonization and activation were carried out with concentrated Sulphuric acid at three different temperatures of 600, 700 and 800 °C, respectively. The activated carbon exhibited excellent microporous and mesoporous structure with a specific surface area that ranges between 30 and 254 m²·g⁻¹ as measured by BET analysis. The morphology and structure of the produced materials are analyzed through Field Emission Scanning Electron Microscopy (FESEM), Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Boehm titration, X-ray Photoelectron Spectroscopy (XPS) and Raman Spectroscopy. X-ray photoelectron spectroscopy indicates that a considerable amount of oxygen is present in the materials. The functional groups in the activated carbon enhanced the electrochemical performance and improved the material’s double-layer capacitance. The carbonized composite activated at 700 °C exhibited excellent capacitance of 456 F g⁻¹ at a specific current of 0.25 A g⁻¹ in 6 M KOH electrolyte and showed excellent stability after 10,000 cycles. Besides being a low cost, the produced materials offer good stability and electrochemical properties, making them suitable for supercapacitor applications.     

The Positive Effect of ZnS in Waste Tire Carbon as Anode for Lithium-Ion Batteries

There is great demand for high-performance, low-cost electrode materials for anodes of lithium-ion batteries (LIBs). Herein, we report the recovery of carbon materials by treating waste tire rubber via a facile one-step carbonization process. Electrochemical studies revealed that the waste tire carbon anode had a higher reversible capacity than that of commercial graphite and shows the positive effect of ZnS in the waste tire carbon. When used as the anode for LIBs, waste tire carbon shows a high specific capacity of 510.6 mAh·g⁻¹ at 100 mA·g⁻¹ with almost 97% capacity retention after 100 cycles. Even at a high rate of 1 A·g⁻¹, the carbon electrode presents an excellent cyclic capability of 255.1 mAh·g⁻¹ after 3000 cycles. This high-performance carbon material has many potential applications in LIBs and provide an alternative avenue for the recycling of waste tires.     

Influence of 3d Transition Metal Doping on Lithium Stabilized Na-β″-Alumina Solid Electrolytes

Na-β″-alumina is the commercially most successful solid electrolyte due to its application in ZEBRA and NAS^® batteries. In this work, Li-stabilized Na-β″-alumina electrolytes were doped with 3d transition metal oxides, namely TiO₂, Mn₃O₄, and NiO, in order to improve their ionic conductivity and fracture strength. Due to XRD and EDX measurements, it was concluded that Mn- and Ni-ions are incorporated into the crystal lattice of Na-β″-alumina. In contrast, TiO₂ doping results in the formation of secondary phases that enable liquid-assisted sintering at temperatures as low as 1500 °C. All dopants increased the characteristic fracture strength of the electrolytes; 1.5 wt% of NiO doping proved to be most efficient and led to a maximal characteristic fracture strength of 296 MPa. Regarding the ionic conductivity, TiO₂ doping showed the uppermost value of up to 0.30 S cm⁻¹ at 300 °C. In contrast to the other dopants, TiO₂ doping lowered the sintering temperature needed to obtain a dense, stable, and highly conductive Na-β″-alumina electrolyte suitable for applications in Na based batteries.     

Properties of PEMA-NH4CF3SO3 Added to BMATSFI Ionic Liquid

Polymer electrolyte films, comprising ammonium trifluoromethanesulfonate salt and butyl-trimethyl ammonium bis(trifluoromethylsulfonyl)imide ionic liquid immobilized in poly (ethyl methacrylate) was studied. Structural, morphological, thermal and electrical properties of the polymer electrolyte films were investigated by differential scanning calorimetry, scanning electron microscopy, and impedance spectroscopy, respectively. Interactions of the salt and ionic liquid with the host polymer were investigated by Fourier transform infra-red spectroscopy. Electrochemical stability of the electrolytes was determined using linear sweep voltammetry and transference numbers corresponding to ionic transport has been evaluated by means of the Wagner polarization technique. The highest conductivity achieved is in the order of 10⁻⁴ S cm⁻¹ for the film added with 35 wt % butyl trimethylammonium bis (trifluoromethanesulfonyl)imide. The film has high amorphicity and low glass transition temperature of 2 °C. The film is electrochemically stable up to 1.8 V. The ion transference number in the polymer film is 0.82 and the conductivity behavior obeys Vogel-Tamman-Fulcher equation.     

Construction of a Three-Dimensional BaTiO3 Network for Enhanced Permittivity and Energy Storage of PVDF Composites

Three-dimensional BaTiO₃ (3D BT)/polyvinylidene fluoride (PVDF) composite dielectrics were fabricated by inversely introducing PVDF solution into a continuous 3D BT network, which was simply constructed via the sol-gel method using a cleanroom wiper as a template. The effect of the 3D BT microstructure and content on the dielectric and energy storage properties of the composites were explored. The results showed that 3D BT with a well-connected continuous network and moderate grain sizes could be easily obtained by calcining a barium source containing a wiper template at 1100 °C for 3 h. The as-fabricated 3D BT/PVDF composites with 21.1 wt% content of 3D BT (3DBT–2) exhibited the best comprehensive dielectric and energy storage performances. An enhanced dielectric constant of 25.3 at 100 Hz, which was 2.8 times higher than that of pure PVDF and 1.4 times superior to the conventional nano–BT/PVDF 25 wt% system, was achieved in addition with a low dielectric loss of 0.057 and a moderate dielectric breakdown strength of 73.8 kV·mm⁻¹. In addition, the composite of 3DBT–2 exhibited the highest discharge energy density of 1.6 × 10⁻³ J·cm⁻³ under 3 kV·mm⁻¹, which was nearly 4.5 times higher than that of neat PVDF.     

Hazardous Petroleum Sludge-Derived Nitrogen and Oxygen Co-Doped Carbon Material with Hierarchical Porous Structure for High-Performance All-Solid-State Supercapacitors

Rational design and sustainable preparation of high-performance carbonaceous electrode materials are important to the practical application of supercapacitors. In this work, a cost-effective synthesis strategy for nitrogen and oxygen co-doped porous carbon (NOC) from petroleum sludge waste was developed. The hierarchical porous structure and ultra-high surface area (2514.7 m² g⁻¹) of NOC electrode materials could provide an efficient transport path and capacitance active site for electrolyte ions. The uniform co-doping of N and O heteroatoms brought enhanced wettability, electrical conductivity and probably additional pseudo-capacitance. The as-obtained NOC electrodes exhibited a high specific capacitance (441.2 F g⁻¹ at 0.5 A g⁻¹), outstanding rate capability, and cycling performance with inconspicuous capacitance loss after 10,000 cycles. Further, the assembled all-solid-state MnO₂/NOC asymmetrical supercapacitor device (ASC) could deliver an excellent capacitance of 119.3 F g⁻¹ at 0.2 A g⁻¹ under a wide potential operation window of 0–1.8 V with flexible mechanical stability. This ASC device yielded a superior energy density of 53.7 W h kg⁻¹ at a power density of 180 W kg⁻¹ and a reasonable cycling life. Overall, this sustainable, low-cost and waste-derived porous carbon electrode material might be widely used in the field of energy storage, now and into the foreseeable future.     

Preparation and Properties of Highly Elastic,Lightweight, and Thermally Insulating SiO2 Fibrous Porous Materials

Fibrous porous materials are one of the most commonly used high-temperature insulation materials because of their high porosity and low thermal conductivity. Due to their wide applications in the aerospace and energy industries, the investigation of high-elastic thermally insulating porous materials has attracted increasing attention. In order to improve the elasticity of fibrous porous materials, quartz fibers with high aspect ratio were used as matrix, sodium hexametaphosphate (SHMP) was selected as dispersant. We innovatively reported that a unique three-dimensional skeleton structure was constructed by adjusting the dispersion of fibers in the slurry, and the lightweight, thermal insulating and elastic SiO₂ fibrous porous material was then prepared by the compression molding method. The characterization results of zeta potential and absorbance showed that the addition of SHMP was an effective method to enhance the dispersibility of quartz fibers in the slurry. SiO₂ fibrous porous materials with 0.4 wt% SHMP content exhibited an ideal three-dimensional skeleton structure, which endowed the porous material with high porosity (89.39%), low density (0.04751 g/cm³), and low thermal conductivity (0.0356 W·m⁻¹·K⁻¹). The three-dimensional skeleton structure formed by overlapping fibers with high aspect ratios endowed the porous material with excellent elasticity. SiO₂ fibrous porous materials with 0.4 wt% SHMP content could undergo large strains of 30% and achieved a resilience ratio of 81.69% under the 30th compression cycle. Moreover, after heat treatment at 800 °C, SiO₂ fibrous porous materials also maintained good elasticity with a resilience ratio of more than 80%.     

Enhanced Storage Performance of PANI and PANI/Graphene Composites Synthesized in Protic Ionic Liquids

Polyaniline (PANI) was synthesized using oxidative polymerization in a mixture of water with pyrrolidinium hydrogen sulfate [Pyrr][HSO₄], which is a protic ionic liquid PIL. The obtained PANI (PANI/PIL) was compared with conventional PANI (PANI/HCl and PANI/HSO₄) in terms of their morphological, structural, and storage properties. The results demonstrate that the addition of this PIL to a polymerization medium leads to a fiber-like morphology, instead of a spherical-like morphology, of PANI/HSO₄ or an agglomerated morphology of PANI/HCl. In addition, PAN/PIL exhibits an improvement of the charge transfer kinetic and storage capability in H₂SO₄ 1 mol·L⁻¹, compared to PANI/HCl. The combination of PANI/PIL and graphene oxide (GO), on the other hand, was investigated by optimizing the PANI/GO weight ratio to achieve the nanocomposite material with the best performance. Our results indicate that the PANI/PIL/GO containing 16 wt% of GO material exhibits a high performance and stability (223 F·g⁻¹ at 10 A·g⁻¹ in H₂SO₄ 1 mol·L⁻¹, 4.9 Wh·Kg⁻¹, and 3700 W·Kg⁻¹ @ 10 A·g⁻¹). The obtained results highlight the beneficial role of PIL in building PANI and PANI/GO nanocomposites with excellent performances for supercapacitor applications.     

A Low-Temperature Heat Output Photoactive Material-Based High-Performance Thermal Energy Storage Closed System

Designing and synthesizing photothermal conversion materials with better storage capacity, long-term stability as well as low temperature energy output capability is still a huge challenge in the area of photothermal storage. In this work, we report a brand new photothermal conversion material obtained by attaching trifluoromethylated azobenzene (Azo_F) to reduced graphene oxide (rGO). Azo_F-rGO exhibits outstanding heat storage density and power density up to 386.1 kJ·kg⁻¹ and 890.6 W·kg⁻¹, respectively, with a long half-life (87.7 h) because of the H-bonds based on high attachment density. Azo_F-rGO also exhibits excellent cycling stability and is equipped with low-temperature energy output capability, which achieves the reversible cycle of photothermal conversion within a closed system. This novel Azo_F-rGO complex, which on the one hand exhibits remarkable energy storage performance as well as excellent storage life span, and on the other hand is equipped with the ability to release heat at low temperatures, shows broad prospects in the practical application of actual photothermal storage.     

Simultaneously Enhanced Thermal Conductivity and Breakdown Performance of Micro/Nano-BN Co-Doped Epoxy Composites

Micro/nano- BN co-doped epoxy composites were prepared and their thermal conductivity, breakdown strength at power frequency and voltage endurance time under high frequency bipolar square wave voltage were investigated. The thermal conductivity and breakdown performance were enhanced simultaneously in the composite with a loading concentration of 20 wt% BN at a micro/nano proportion of 95/5. The breakdown strength of 132 kV/mm at power frequency, the thermal conductivity of 0.81 W·m⁻¹·K⁻¹ and voltage endurance time of 166 s were obtained in the composites, which were approximately 28%, 286% and 349% higher than that of pristine epoxy resin. It is proposed that thermal conductive pathways are mainly constructed by micro-BN, leading to improved thermal conductivity and voltage endurance time. A model was introduced to illustrate the enhancement of the breakdown strength. The epoxy composites with high thermal conductivity and excellent breakdown performance could be feasible for insulating materials in high-frequency devices.     

Self-Template Synthesis of Nitrogen-Doped Hollow Carbon Nanospheres with Rational Mesoporosity for Efficient Supercapacitors

Rational design and economic fabrication are essential to develop carbonic electrode materials with optimized porosity for high-performance supercapacitors. Herein, nitrogen-doped hollow carbon nanospheres (NHCSs) derived from resorcinol and formaldehyde resin are successfully prepared via a self-template strategy. The porosity and heteroatoms in the carbon shell can be adjusted by purposefully introducing various dosages of ammonium ferric citrate (AFC). Under the optimum AFC dosage (30 mg), the as-prepared NHCS-30 possesses hierarchical architecture, high specific surface area up to 1987 m²·g⁻¹, an ultrahigh mesopore proportion of 98%, and moderate contents of heteroatoms, and these features endow it with a high specific capacitance of 206.5 F·g⁻¹ at 0.2 A·g⁻¹, with a good rate capability of 125 F·g⁻¹ at 20 A·g⁻¹ as well as outstanding electrochemical stability after 5000 cycles in a 6 M KOH electrolyte. Furthermore, the assembled NHCS-30 based symmetric supercapacitor delivers an energy density of 14.1 W·h·kg⁻¹ at a power density of 200 W·kg⁻¹ in a 6 M KOH electrolyte. This work provides not only an appealing model to study the effect of structural and component change on capacitance, but also general guidance to expand functionality electrode materials by the self-template method.     

Influence of Low Sintering Temperature on BaCe0.2Zr0.6Y0.2O3−δ IT-SOFC Perovskite Electrolyte Synthesized by Co-Precipitation Method

BaCe_0.2Zr_0.6Y_0.2O_3−δ (BCZY) perovskite electrolytes were synthesized for intermediate-temperature solid oxide fuel cell with a cost-effective and versatile co-precipitation method. The synthesized BCZY electrolytes were sintered at 900, 1000, and 1100 °C to observe the effects of low sintering temperature on the structural, morphological, thermal, and electrical properties of BCZY. All BCZY electrolytes materials exhibited a crystalline perovskite structure and were found to be thermally stable. The crystallinity and conductivity of BCZY electrolyte enhanced with increased sintering temperature, due to the grain growth. At the same time, secondary phases of carbonates were also observed for samples sintered at a temperature lower than 1100 °C. The BCZY sintered at 1100 °C exhibited a density >95%, and a power density of 350 mWcm⁻² with open-circuit voltage 1.02 V at 650 °C was observed due its dense and airtight structure. Based on the current investigation, we suggest that the BaCe_0.2Zr_0.6Y_0.2O_3−δ perovskite electrolyte sintered at a temperature of 1100 °C is a suitable electrolyte for IT-SOFC.     

Enhanced Electrochemical Performance Promoted by Tin in Silica Anode Materials for Stable and High-Capacity Lithium-Ion Batteries

Although the silicon oxide (SiO₂) as an anode material shows potential and promise for lithium-ion batteries (LIBs), owing to its high capacity, low cost, abundance, and safety, severe capacity decay and sluggish charge transfer during the discharge–charge process has caused a serious challenge for available applications. Herein, a novel 3D porous silicon oxide@Pourous Carbon@Tin (SiO₂@Pc@Sn) composite anode material was firstly designed and synthesized by freeze-drying and thermal-melting self-assembly, in which SiO₂ microparticles were encapsulated in the porous carbon as well as Sn nanoballs being uniformly dispersed in the SiO₂@Pc-like sesame seeds, effectively constructing a robust and conductive 3D porous Jujube cake-like architecture that is beneficial for fast ion transfer and high structural stability. Such a SiO₂@Pc@Sn micro-nano hierarchical structure as a LIBs anode exhibits a large reversible specific capacity ~520 mAh·g⁻¹, initial coulombic efficiency (ICE) ~52%, outstanding rate capability, and excellent cycling stability over 100 cycles. Furthermore, the phase evolution and underlying electrochemical mechanism during the charge–discharge process were further uncovered by cyclic voltammetry (CV) investigation.     

High Electrochemical Performance Silicon Thin-Film Free-Standing Electrodes Based on Buckypaper for Flexible Lithium-Ion Batteries

Recently, applications for lithium-ion batteries (LIBs) have expanded to include electric vehicles and electric energy storage systems, extending beyond power sources for portable electronic devices. The power sources of these flexible electronic devices require the creation of thin, light, and flexible power supply devices such as flexile electrolytes/insulators, electrode materials, current collectors, and batteries that play an important role in packaging. Demand will require the progress of modern electrode materials with high capacity, rate capability, cycle stability, electrical conductivity, and mechanical flexibility for the time to come. The integration of high electrical conductivity and flexible buckypaper (oxidized Multi-walled carbon nanotubes (MWCNTs) film) and high theoretical capacity silicon materials are effective for obtaining superior high-energy-density and flexible electrode materials. Therefore, this study focuses on improving the high-capacity, capability-cycling stability of the thin-film Si buckypaper free-standing electrodes for lightweight and flexible energy-supply devices. First, buckypaper (oxidized MWCNTs) was prepared by assembling a free stand-alone electrode, and electrical conductivity tests confirmed that the buckypaper has sufficient electrical conductivity (10⁻⁴(S m⁻¹) in LIBs) to operate simultaneously with a current collector. Subsequently, silicon was deposited on the buckypaper via magnetron sputtering. Next, the thin-film Si buckypaper freestanding electrodes were heat-treated at 600 °C in a vacuum, which improved their electrochemical performance significantly. Electrochemical results demonstrated that the electrode capacity can be increased by 27/26 and 95/93 μAh in unheated and heated buckypaper current collectors, respectively. The measured discharge/charge capacities of the USi_HBP electrode were 108/106 μAh after 100 cycles, corresponding to a Coulombic efficiency of 98.1%, whereas the HSi_HBP electrode indicated a discharge/charge capacity of 193/192 μAh at the 100th cycle, corresponding to a capacity retention of 99.5%. In particular, the HSi_HBP electrode can decrease the capacity by less than 1.5% compared with the value of the first cycle after 100 cycles, demonstrating excellent electrochemical stability.     

Enhancement of Y5−xPrxSb3−yMy (M = Sn,Pb) Electrodes for Lithium- and Sodium-Ion Batteries by Structure Disordering and CNTs Additives

The maximally disordered (MD) phases with the general formula Y_5−xPr_xSb_3−yM_y (M = Sn, Pb) are formed with partial substitution of Y by Pr and Sb by Sn or Pb in the binary Y₅Sb₃ compound. During the electrochemical lithiation and sodiation, the formation of Y_5-xPr_xSb_3-yM_yLi_z and Y_5−xPr_xSb_3−yM_yNa_z maximally disordered–high entropy intermetallic phases (MD-HEIP), as the result of insertion of Li/Na into octahedral voids, were observed. Carbon nanotubes (CNT) are an effective additive to improve the cycle stability of the Y_5−xPr_xSb_3−yM_y (M = Sn, Pb) anodes for lithium-ion (LIBs) and sodium-ion batteries (SIBs). Modification of Y_5−xPr_xSb_3−ySn_y alloys by carbon nanotubes allowed us to significantly increase the discharge capacity of both types of batteries, which reaches 280 mAh · g⁻¹ (for LIBs) and 160 mAh · g⁻¹ (for SIBs), respectively. For Y_5−xPrxSb_3−yPb_y alloys in which antimony is replaced by lead, these capacities are slightly smaller and are 270 mAh · g⁻¹ (for LIBs) and 155 mAh · g⁻¹ (for SIBs), respectively. Results show that structure disordering and CNT additives could increase the electrode capacities up to 30% for LIBs and up to 25% for SIBs.     

Praseodymium Orthoniobate and Praseodymium Substituted Lanthanum Orthoniobate: Electrical and Structural Properties

In this paper, the structural properties and the electrical conductivity of La_1−xPr_xNbO_4+δ (x = 0.00, 0.05, 0.1, 0.15, 0.2, 0.3) and PrNbO_4+δ are presented and discussed. All synthesized samples crystallized in a monoclinic structure with similar thermal expansion coefficients. The phase transition temperature between the monoclinic and tetragonal structure increases with increasing praseodymium content from 500 °C for undoped LaNbO_4+δ to 700 °C for PrNbO_4+δ. Thermogravimetry, along with X-ray photoelectron spectroscopy, confirmed a mixed 3⁺/4⁺ oxidation state of praseodymium. All studied materials, in humid air, exhibited mixed protonic, oxygen ionic and hole conductivity. The highest total conductivity was measured in dry air at 700 °C for PrNbO_4+δ, and its value was 1.4 × 10⁻³ S/cm.