Direct simultaneous determination of dihydroxybenzene isomers at C-nanotube-modified electrodes by derivative voltammetry

The voltammetric behavior of dihydroxybenzene isomers was studied with glassy carbon electrodes modified with multi-wall carbon nanotubes. In 0.1 mol L^?1 HAc + NaAc buffer solution (pH 5.5), the modified electrode showed a good electrocatalytic response towards dihydroxybenzenes. The peak currents increased significantly and their oxidation potentials shifted negatively. Through a derivative technique, the three oxidation peaks of dihydroxybenzene isomers can be separated, thus the method can be applied to direct simultaneous determination without previous separation. The linear calibration ranges were 2 × 10^?6–1 × 10^?4 mol L^?1 for hydroquinone and catechol, respectively, and 5 × 10^?6 to 8 × 10^?5 mol L^?1 for resorcinol, with detection limits of 6 × 10^?7, 6 × 10^?7 and 1 × 10^?6 mol L^?1, respectively. This method has been applied to the direct determination of dihydroxybenzene isomers in artificial wastewater, and the recovery was from 92% to 104%.     

Electrochemical behavior of quercetin: Experimental and theoretical studies

Electrochemical oxidation of quercetin, as important biological molecule, has been studied in 0.1 M phosphate buffer solution, using cyclic voltammetry, chronoamperometry, rotating disk electrode voltammetry as well as quantum mechanical calculations. The heterogeneous charge transfer rate constant, k′, transfer coefficient, α, and exchange current density, j₀, for oxidation of quercetin at the glassy carbon electrode are determined as 4.84 × 10^?2 cm s^?1, 0.65 ± 0.01 and (1.17 ± 0.39) × 10^?7 A cm^?2, respectively. The formal potential, E^0′, of quercetin is pH dependent with a slope of ?60.1 mV per unit of pH which is close to the anticipated Nernstian value of ?59 mV for a two electrons and two protons process. The standard formal potential, E⁰, of quercetin was found to be equal with 558 mV versus saturated calomel electrode (SCE). The mechanism of oxidation was deduced from voltammetric data in various pHs and also in different concentrations of quercetin. The diffusion coefficient of quercetin was calculated as 3.18 × 10^?6 cm² s^?1 for the experimental condition, using chronoamperometric results. The results of density functional theory (DFT) calculations for the oxidation of quercetin in aqueous solution, are also presented. The theoretical standard electrode potential of quercetin is obtained to be 568 mV versus SCE, which is in good agreement with the experimental value. The discrepancy between theoretical and experimental values is only 10 mV. The agreement verifies the accuracy of experimental method and the validity of mathematical model.     

Reactions of the nitro radical anion of metronidazole in aqueous and mixed solvent: a cyclic voltammetric study

Cyclic voltammetry was used to investigate the electrochemical reduction of metronidazole (2-methyl-5-nitro-1H-imidazole-1-ethanol) at glassy carbon and gold electrodes at different pHs in aqueous solution as well as in mixed solvent viz., aqueous dimethyl formamide. The electrogenerated nitro radical anion undergoes a disproportionation reaction, the rate constant of which is dependent on the pH, solvent composition and electrode material. The interactions of the nitro radical anion with thymine and cytosine were also investigated using a cyclic voltammetric technique. Both the bases were found to react with metronidazole nitro radical anion. The rate constants for such reactions in aqueous solutions were 3.5 × 10³ and 3.0 × 10³ dm³ mol^?1 s^?1 for thymine and cytosine, respectively.     

Improvement of alternariol monomethyl ether detection at gold electrodes modified with a dodecanethiol self-assembled monolayer

The electro-oxidation of alternariol monomethyl ether (AME), one of the main metabolites of the Alternaria genus mycotoxins, is studied at 1-dodecanethiol (DDT)-modified gold electrodes, in acetonitrile (ACN) – aqueous phosphate buffer solutions of different pH values, by using cyclic (CV) and square-wave (SWV) voltammetries. The AME voltammetric response at the bare electrode suffers from two drawbacks: it appears at potentials close to the onset of gold oxide formation, and it is hampered by a fouling of the electrode surface due to the accumulation of oxidized products. These shortcomings are circumvented by the use of DDT-coated electrodes, since the intervening monolayer inhibits gold oxide formation and surface passivation by the electrochemical products, without affecting the oxidation kinetics of AME significantly. Diagnostic criteria based on the voltammetric peak parameters show that the electrochemical behavior of AME at the modified electrode is mainly controlled by reactant diffusion from solution, with a weak adsorption of both the mycotoxin and its oxidation products at monolayer defects. Calibration curves were constructed from the AME square-wave voltammetric response and a detection limit of 9.1 × 10^?8 mol dm^?3 was determined, which is about three times smaller than a previous estimate at platinum and glassy carbon electrodes, and about fifty times smaller than the limit derived from measurements carried out at a polyphenol oxidase-modified carbon paste electrode.     

Characterization and electrocatalytic properties of cobalt hexacyanoferrate films immobilized on Au-colloid modified gold electrodes

An electroactive cobalt hexacyanoferrate (CoHCF) film was electrodeposited from a solution containing Co²⁺ and Fe(CN)₆^3? ions on the bare gold or the Au-colloid modified electrode. The cation (Li⁺, Na⁺, K⁺, Rb⁺, Cs⁺, Mg²⁺, Ca²⁺, Sr²⁺ and Ba²⁺) and the anion (F^?, Cl^? and Br^?) effects on the redox peak of the CoHCF film were investigated in detail. On the other hand, the electrocatalytic oxidations of thiosulfate at the CoHCF/gold and CoHCF/Au-colloid/gold electrodes were compared. At the CoHCF/Au-colloid/gold electrode, we obtained a response current larger by a factor of 2 and a three times lower detection limit than those at a CoHCF/gold electrode. The linear ranges were 1.0 × 10^?4 to 2.8 × 10^?3 M for the CoHCF/gold electrode and 7.5 × 10^?5 to 4.8 × 10^?3 M for the CoHCF/Au-colloid/gold electrode. These results showed that the immobilized CoHCF at the Au-colloid modified electrode exhibited a higher catalytic activity and a wider linear range toward thiosulfate. Additionally, the effects of the applied potential and the solution pH were studied.     

Novel solid-state cadmium ion-selective electrodes based on its tetraiodo- and tetrabromo-ion pairs with cetylpyridinium

Two novel cadmium solid-state ion-selective electrodes have been prepared by coating the surface of a graphite rod electrode directly with tetrahydrofuran solution containing PVC, cetylpyridinium–tetraiodocadmate (I) or cetylpyridinium–tetrabromocadmate (II), dioctyl phthalate and sodium tetraphenyl borate. The two sensors exhibit near-Nernstian anionic slopes of ?29.8 and ?25.1 mV/concentration decade, independently of pH over a wide range, with very fast response times of 3 and 7 s, respectively. The tetraiodocadmate (TIC) and tetrabromocadmate (TBC) electrodes posses linear ranges of 1.5 × 10^?6–1 × 10^?1 and 1.0 × 10^?6–1 × 10^?1 M and lower detection limits (LDL) of 6 × 10^?7 and 8 × 10^?7 M, respectively. The effects of membrane composition, type of plasticizer and pH of the sample solution were investigated thoroughly. The TBC electrode is shown to be free of all interference that is common for most of the reported cadmium ISEs except for that of Hg²⁺ ion. The two electrodes were applied for the determination of cadmium in some alloys and polluted water.     

Voltammetric and XPS investigations of nickel hydroxide electrochemically dispersed on gold surface electrodes

A chemically modified electrode composed of mixed hydroxide and oxyhydroxide nickel film (6–8 nmol cm^?2) on the gold substrate (Au ∣ Ni) was characterized by cyclic voltammetry and XPS techniques. The gold substrate electrodes were firstly electrochemically conditioned in 0.2 M NaOH by cycling the potential between ?0.25 and 0.6 V versus SCE, then modified by cathodic electrodeposition of nickel hydroxide films. These nickel films were obtained either by voltage cycling (50 mV s^?1) between 0.0 and ?0.5 V (SCE) or at constant potential of ?0.3 or ?0.5 V using non-deaerated 50 mM Ni(NO₃)₂ solutions. X-ray photoelectron spectroscopy (XPS) characterisation and voltammetric behaviour of Au ∣ Ni electrodes in alkaline solutions are described. Continuous electrochemical cycling of the Au ∣ Ni electrodes induces significant changes of the nickel films in terms of crystallographic structures and chemical composition. Combination of XPS and electrochemical methodologies have demonstrated the ability to follow the morphological and chemical changes in alkaline solutions upon cycling potentials. Angular-dependent XPS measurements have demonstrated that electrochemical treatment induces the formation of a uniform film layer with the following chemical distribution: Au ∣ Ni(OH)₂ ∣ NiOOH. The electrocatalytic activity of the Au ∣ Ni electrodes is investigated in alkaline medium using glucose as a model compound. The favourable combination of active species such as gold and nickel leads to a sensing electrode with strong catalytic activity over a wide range of applied potentials.     

A voltammetric sensor based on graphene-modified electrode for simultaneous determination of catechol and hydroquinone

In this report, a voltammetric sensor for simultaneous determination of hydroquinone (HQ) and catechol (CC) was developed at a glassy carbon electrode modified with graphene (GR/GCE). The separation of oxidation and reduction peak (ΔE) is decreased from 281 to 31 mV for HQ and from 250 to 26 mV for CC at GR/GCE, respectively. Separation of the oxidation peak potentials for HQ and CC was about 112 mV in 0.10 M acetate buffer solution (pH 4.5), and the anodic currents for the oxidation of both HQ and CC are greatly increased at GR/GCE, which makes it suitable for simultaneous determination of these compounds. Under the optimized condition, the anodic peak current of HQ is linear with the concentration of HQ from 1 × 10^?6 to 5 × 10^?5 M in the presence of 5 × 10^?5 M CC. A detection limit of 1.5 × 10^?8 M (S/N = 3) can be achieved. At the same time, the anodic current of CC is linear with the concentration of CC from 1 × 10^?6 to 5 × 10^?5 M with a detection limit of 1.0 × 10^?8 M (S/N = 3) in the presence of 5 × 10^?5 M HQ. The proposed sensor was successfully applied to the simultaneous determination of HQ and CC in tap water, and the results are satisfactory.     

The electrochemistry and thin-layer luminescence spectroelectrochemistry of rhodamine 6G at a 4,4′-bipyridine-modified gold electrode

We report on the first direct electrochemistry and fluorescence spectroelectrochemistry of rhodamine 6G at a 4,4′-bipyridine-modified gold electrode. The value of n determined in spectropotentiostatic experiments at 1.87×10^?6 mol l^?1 of rhodamine 6G in 0.20 mol l^?1 KCl solution is 1.15, and the experimental value obtained for E⁰′ is ?0.787 V versus Ag ∣ AgCl ∣ KCl_sat, which agrees very well with the value (E⁰′=?0.791 V) obtained using cyclic voltammetry at a modified gold electrode. The values of the diffusion coefficients D_O and D_R for the oxidized and reduced forms of rhodamine 6G calculated from results of potential step and in situ fluorescence measurement experiments are 4.0×10^?6 cm² s^?1 and 4.2×10^?6 cm² s^?1, respectively. Cyclic voltammograms of rhodamine 6G show that the peak current I_p is proportional to the square root of the potential scan rate v^1/2, the ratio of the reduction to the oxidation peak height is about unity, and the separation of both reduction and reoxidation peak potentials ΔE_P is essentially constant at 135 mV at low scan rates. These results indicate that electrochemistry of rhodamine 6G at a 4,4′-bipyridine-modified gold electrode is a quasi-reversible one-electron electrode process.     

Direct electron transfer between the heme of cellobiose dehydrogenase and thiol modified gold electrodes

Cellobiose dehydrogenase (CDH) is an extracellular fungal enzyme with two domains, one containing flavin adenine dinucleotide (FAD) and one containing heme. The electrochemistry of CDH, as well as its cleaved FAD- and heme-subunits, was studied using a membrane electrode, i.e. the enzyme was trapped under a permselective membrane on a cystamine or 3-mercaptopropionic acid modified gold electrode. Direct un-mediated electron transfer (ET) between the heme of CDH and thiol modified gold electrodes was demonstrated using cyclic voltammetry. At low sweep rate (10 mV s^?1) and low pH (pH 4.3) up-hill ET from heme to FAD in CDH was observed. The formal potential of the heme in CDH and in the cleaved heme-subunit was found to be the same and equal to ?41 mV versus Ag ∣ AgCl at pH 5.1. The dependence of the formal potential on the pH (in the pH range 3.6–6.0) indicates the presence of one redox-linked ionisable functional group. Entropy and enthalpy changes were determined in variable temperature experiments as follows, ΔS°′=?194±14 J mol^?1 K^?1 and ΔH°′=?74±6 kJ mol^?1. The electrocatalytic behaviour of the CDH electrodes was demonstrated by addition of the enzyme substrate, cellobiose. The catalytic current was shown to decrease upon increased pH, in accordance with previous kinetic data in solution. The model of electron transport from the substrate (cellobiose) to FAD, and then through the heme domain to the electrode was confirmed in the experiments.     

Catechin antioxidant action at various pH studied by cyclic voltammetry and PM3 semi-empirical calculations

The mechanism of catechin electro-oxidation at various pH was studied using cyclic voltammetry (CV) on the glassy carbon (GC) electrode and PM3 semi-empirical calculations. The influence of activation of the surface of the GC electrode on CV results has been discussed. Mixed adsorption–diffusion control has been observed by applying mechanistic criteria of CV to the results obtained at the activated electrode. The calculated catechin diffusion coefficient D = 2.78 × 10^?6 cm² s^?1. A linear increase of the current peak has been observed with the increase of substrate concentration up to 40 μmol dm^?3 (surface coverage Γ ～ 10^?11 mol cm^?2). In the whole investigated pH range, the dE/dpH value is very close to the anticipated Nernstian dependence of ?59 mV/pH indicating that the slope is not affected by the different sequences of e^? and H⁺ transfer. Molecular modeling results show a decrease of ≈5 kcal mol^?1 in ΔHoF (between radical and parent molecule) and a decrease of ≈6 eV in IP (of the parent molecule) when the parent molecule is changed from neutral to monoanionic form of catechin showing that both processes – hydrogen and electron abstraction are facilitated by deprotonation. Electrochemical oxidation of catechin is known to proceed as a two step one-electron oxidation of the B-ring of o-phenolic groups. Upon an increase in the pH, the mechanistic pathway of catechin electro-oxidation in both oxidation steps changes from an eH to the He process. In the reaction with a free radical, this may induce the change from hydrogen to electron donation.     

Voltammetric trace metal determinations by cathodic and anodic stripping voltammetry in environmental matrices in the presence of mutual interference

Arsenic(III), selenium(IV), copper(II), lead(II), cadmium(II), zinc(II) and manganese(II) have been determined in environmental matrices by differential pulse cathodic (DPCSV) and anodic (DPASV) stripping voltammetry. The voltammetric measurements were carried out using, as the working electrode, a stationary mercury electrode, and a platinum electrode and a Ag ∣ AgCl ∣ KCl_(sat) electrode as the auxiliary and reference electrode, respectively. An ammonia+ammonium chloride buffer of pH 9.0 was employed as the supporting electrolyte. The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403, Estuarine Sediment BCR-CRM 277, Ulva Lactuca BCR-CRM 279 and Mussel Tissue BCR-CRM 278. The precision and accuracy, expressed as relative standard deviation and relative error, respectively, were lower than 5% in all cases, while the detection limit for each element was around 10^?9 mol l^?1. In the presence of high reciprocal interference, the standard addition method considerably improved the resolution of the voltammetric technique. The analytical procedure was transferred and applied to samples drawn in the Goro Bay (Ferrara, Italy).     

Surface structures at the initial stages in passive film formation on Ni(1 1 1) electrodes in acidic electrolytes

The adsorption of sulfate or OH species and subsequent Ni(OH)₂ film growth on Ni(1 1 1) single crystal electrodes has been investigated using in situ infrared reflection absorption spectroscopy (IRAS) as well as scanning tunneling microscopy (STM). In a pH 3 sulfuric acid solution, STM images show that a well-defined Ni(1 1 1) surface with a (1 × 1) lattice is exposed at ?300 mV, while hexagonal close-packed images with an atomic spacing of 0.32 nm are grown on this electrode at 300 mV. On the other hand, IRAS results in a sulfuric acid solution (pH 3) reveal that an absorption band at 1116 cm^?1, which can be ascribed to ν(S–O) symmetric stretching of sulfate anion on Ni(1 1 1) surface, starts to appear at ?400 mV and develops its intensity with an electrode potential increase, while an absorption band at 930 cm^?1 begins to develop at 0 mV on Ni(1 1 1), Ni(1 0 0) and Ni(1 1 0) electrodes, which can be assigned to an in-plane δ(Ni–OH) bending vibration in Ni(OH)₂ passive film.     

Electrochemical behavior of iodide at a nickel pentacyanonitrosylferrate film modified aluminum electrode prepared by an electroless procedure

The surface of an aluminum disk electrode was modified by a thin film of nickel pentacyanonitrosylferrate and used for electrocatalytic oxidation of iodide. The cyclic voltammogram of the modified Al electrode showed surface redox behavior due to the [Ni^IIFe^III/II(CN)₅NO]^0/1? redox couple. The modifying layer shows excellent catalytic activity toward the oxidation of iodide. Different supporting electrolytes containing different alkali metal cations affected the apparent formal potential of the redox films and thus, changed the thermodynamic tendency and kinetics of the modifying film toward the catalytic oxidation of iodide. This was explained by including the concept of a surface coverage normalized-catalytic current. The kinetics of the catalytic reaction were investigated by cyclic voltammetry and rotating disk electrode voltammetry in a suitable supporting electrolyte. The results were explained using the theory of electrocatalytic reactions at chemically modified electrodes. The heterogeneous rate constant for the catalytic reaction, k, diffusion coefficient of iodide in solution, D, and transfer coefficient, α, were found to be 5.8 × 10² M^?1 s^?1, 1.3 × 10^?5 cm² s^?1 and 0.66, respectively. In addition the effect of electrode surface coverage on the dynamic range of a calibration curve was investigated. Under optimum conditions a linear calibration graph was obtained over an iodide concentration range of 2–100 mM.     

Cyclic voltammetric determination of free radical species from nitroimidazopyran: a new antituberculosis agent

PA-824 (2-nitro-6-(4-trifluoromethoxy-benzyloxy)-6,7-dihydro-5H-imidazo[2,1-b][1,3]oxazine) is being tested as antituberculosis drug. Little is known on the action mechanism of PA-824; however the reduction of the nitro group seems to be a key step in the metabolic activation, as is observed for the well-known bactericidal metronidazole. Consequently, this paper is focused on the cyclic voltammetric behavior of PA-824 with the aim of revealing the formation and stability of the corresponding nitro radical anion and its comparison with the metronidazole behavior.Both compounds PA-824 and metronidazole reveal, in aprotic medium (DMSO + 0.1 tetrabutylammonium hexafluorophosphate), a similar reduction pattern showing a well-resolved couple due to nitro reduction to form the corresponding nitro radical anion. The electrode reaction obeys an EC₂ mechanism with a dimerization reaction as the chemical step in aprotic medium. Using cyclic voltammetry theory for a dimerization reaction we have calculated the second-order decay constants, k_2,dim, and the half-life time, t_1/2, for the nitro radical anions formed from PA-824 and metronidazole. We have obtained k_2,dim values of 2.22 × 10² and 2.58 × 10⁴ M^?1s^?1 for metronidazole and PA-824, respectively. Our voltammetric results show that the PA-824 nitro radical anion requires more energy for formation (about 200 mV) and it is approximately 100 times less stable than the metronidazole radical anion.     

Electrochemical properties of a tetrabromo-p-benzoquinone modified carbon paste electrode. Application to the simultaneous determination of ascorbic acid,dopamine and uric acid

The electrochemical study of a tetrabromo-p-benzoquinone modified carbon paste electrode (TBQ-MCPE), as well as its efficiency for electrocatalytic oxidation of ascorbic acid, dopamine and uric acid, is described. Cyclic voltammetry was used to investigate the redox properties of this modified electrode at various solution pH values and at various scan rates. Three linear segments were found with slope values of ?58.4 mV/pH, ?28.1 mV/pH and 0.0 mV/pH in the pH range 2.0–7.1, pH 7.1–9.0 and pH 9.0–11.0, respectively. The apparent charge transfer rate constant, k_s, and transfer coefficient, α, for electron transfer between TBQ and CPE were calculated as 3.79 ± 0.10 s^?1 and 0.55, respectively. The electrode was also employed to study the electrocatalytic oxidation of AA, using cyclic voltammetry, chronoamperometry and differential pulse voltammetry as diagnostic techniques. It has been found that the oxidation of AA at the surface of TBQ-MCPE occurs at a potential of about 430 mV less positive than that of an unmodified CPE. The diffusion coefficient of AA was also estimated using chronoamperometry. The kinetic parameters such as the electron transfer coefficient, α, and heterogeneous rate constant, $k_{\mathrm{h}}^{\prime }$, for oxidation of AA at the TBQ-MCPE surface was determined using cyclic voltammetry. Differential pulse voltammetry (DPV) exhibits two linear dynamic ranges and a detection limit of 0.62 μM for AA. In DPV, the TBQ-MCPE could separate the oxidation peak potentials of AA, DA and UA present in the same solution, though at the unmodified CPE the peak potentials were indistinguishable. This modified electrode was quite effective not only to detect AA, DA and UA, but also in simultaneous determination of each component concentration in the mixture.     

Carbon paste electrodes of the mixed oxide SiO2/Nb2O5 prepared by the sol–gel method: dissolved dioxygen sensor

A carbon paste of SiO₂/Nb₂O₅ material was used as the electrode in the development of a dissolved dioxygen sensor in 1.0 mol l^?1 KCl solution at pH 6.2. The material was prepared by the sol–gel method. In the investigation of its electrochemical properties, linear and cyclic voltammetric and chronoamperometric techniques were employed. Dioxygen reduction, which was diffusion controlled, occurred at ?280 mV vs. SCE by a two electron mechanism, producing peroxide. A linear response between the cathodic peak current intensity and the dissolved O₂ concentration was obtained for the region between 1.0 and 13.6 mg l^?1. The stability proved to be very good over successive voltammetric cycles. The electrode response time was about 5 s. The electron transfer reactions were explained as being to an n-type semiconductor of niobia dispersed in the silica surface.     

A piezoelectric gene-sensor using actinomycin D-functionalized nano-microspheres as amplifying probes

A gene-sensing system has been developed using actinomycin D-functionalized magnetic nano-microspheres, which can interact with double-stranded DNAs (dsDNAs) anchored on the gold film electrode of an electrochemical quartz crystal microbalance (EQCM). Actinomycin D acts as a guide that leads heavy microspheres onto the dsDNAs at the EQCM film. A magnetic separation shelf could separate unreacted microspheres conveniently. The modification and DNA hybridization at EQCM electrodes were examined by microgravimetric and electrochemical methods. In this way, an outstanding change in frequency decrease has been monitored owing to the mass increase on the EQCM electrodes. The limit for the determination of target DNA could be improved from 6.2×10^?8 to 2.0×10^?12 mol l^?1 by the amplifying technique.     

Interactions between DNA and a water-soluble C60 derivative studied by surface-based electrochemical methods

A novel electrochemical micromethod for the investigation of the interactions between DNA and non-electroactive species is described. The method was developed using the system of double-stranded DNA (dsDNA) modified gold electrodes (dsDNA/Au), a synthesized water-soluble C₆₀ derivative as a model, and [Co(phen)₃]^3+/2+ (phen=1,10-phenanthroline) as an electroactive indicator. Electrochemical studies with dsDNA-modified gold electrodes suggest that the C₆₀ derivative can interact strongly with dsDNA, with binding sites of the major groove of the double helix and phosphate backbone of dsDNA, a binding constant of (1.6 ± 0.2) × 10⁵ M^?1 obtained in 5 mM NaCl in Tris–HCl buffer, and a dissociation rate constant from the dsDNA/Au surface of (1.2 ± 0.1) × 10^?2 min^?1.     

The reduction of l-cystine hydrochloride at lead using static and rotating disc electrodes

The reduction of the disulphide, l-cystine hydrochloride to the l-cysteine hydrochloride thiol, in 0.1 mol dm^?3 HCl at 298 K, has been studied at pre-treated, circular, 0.50 cm² lead disc electrodes using steady state linear sweep voltammetry, non-steady state voltammetry and controlled potential coulometry. The diffusion coefficient for l-cystine hydrochloride was approximately 4.8 × 10^?10 m² s^?1 from the three techniques. Reduction of the disulphide was irreversible and hydrogen evolution occurred as a competitive reaction at approximately ?1.35 V vs. SCE. Analysis of the mixed control kinetics, using a Koutecky–Levich approach, allowed the relative roles of charge transfer and mass transport to be resolved. Anomalously high Tafel slopes, of typically ?183 mV, were observed due to disulphide adsorption. The charge transfer kinetics are consistent with the first electron gain being rate determining while reaction orders are +1 with respect to both the disulphide and proton concentrations. The mechanism of l-cystine hydrochloride reduction has been critically discussed.