In vivo evaluation of a porous hydroxyapatite/poly-DL-lactide composite for use as a bone substitute

We investigated the biocompatibility, osteoconductivity, and biodegradability of a porous composite of hydroxyapatite (HA) and poly-DL-lactide (PDLLA) implanted into rabbit femoral condyles and compared it with porous HA. Six weeks after implantation, the HA/PDLLA was covered with bone and contacted the bone directly. The amount of newly formed bone in the pores was similar in both materials during the examined period. The newly formed bone in the HA/PDLLA tended to increase over 26 weeks, but that in the HA did not show a significant increase after 12 weeks. By 26 weeks, remodeling of the newly formed bone in the pores was seen and bone marrow tissue was found in the pores of the HA/PDLLA. The porous HA/PDLLA was resorbed much faster than the porous HA. Porous HA/PDLLA was resorbed continuously through bone formation and remodeling. Conversely, porous HA was scarcely resorbed throughout the period. HA/PDLLA is thought to be degraded almost completely after about 1 year, and in this study, porous HA/PDLLA showed excellent osteoconductivity and faster resorption than HA. Therefore, HA/PDLLA might be a desirable material for bone substitutes.     

多孔磷酸钙骨水泥与转染骨形态发生蛋白2基因的骨髓间充质干细胞复合修复股骨髁骨缺损

BACKGROUND: Bone morphogenetic protein (BMP) can improve the osteogenesis capacity of tissue-engineered bone. However, how to prolong BMP release is a key for constructing tissue-engineered bone. OBJECTIVE: To study the repair effect of porous calcium phosphate cement (CPC) with bone marrow mesenchymal stem cells transfected with BMP-2 gene on bone defects. METHODS: After modeling of bilateral femoral condyle bone defects, 12 model rabbits were given implantation of porous CPC with bone marrow mesenchymal stem cells transfected with BMP-2 on the left (experimental group) and given implantation of porous CPC with bone marrow mesenchymal stem cells on the right (control group). Bilateral femoral condyles were taken and analyzed histologically at 4 and 12 weeks after implantation. RESULTS AND CONCLUSION: Better osteogenesis including more newly formed bone tissues and faster scaffold absorption was observed in the experimental group compared with the control group at 4 and 12 weeks after implantation. The area of newly formed bone tissues at different time and rate of bone formation at 12 weeks were significantly higher in the experimental group than in the control group (P < 0.001, P < 0.05). These findings indicate that transfer of BMP-2 into bone marrow mesenchymal stem cells combined with porous CPC could increase repair of bone defects.     

Bone inductive properties of rhBMP-2 loaded porous calcium phosphate cement implants inserted at an ectopic site in rabbits

Recombinant human bone morphogenetic protein-2 (rhBMP-2) is known for its osteoinductive potential in bone tissue engineering. Calcium phosphate (Ca-P) cements are injectable, osteoconductive ceramic materials in which a macroporous structure can be induced during the setting reaction. In this study, the osteoinductive capability of rhBMP-2 loaded porous Ca-P cement was evaluated. Porous Ca-P cement discs were made and loaded with rhBMP-2 in vitro and implanted subcutaneously in the back of New Zealand white rabbits. The implantation period was either 2 or 10 weeks. Histological analysis of retrieved specimens revealed evident bone formation in the rhBMP-2 loaded Ca-P cement discs (pore fill: 18+/-6%) after 10 weeks of implantation. Bone formation occurred only in rhBMP-2 loaded porous Ca-P cement discs. Degradation of the Ca-P cement could not be confirmed after 10 weeks of implantation. The scaffold maintained its shape and stability during this time period. We conclude that porous Ca-P cement is a suitable carrier material for ectopic bone engineering.     

An initial investigation of photocurable three-dimensional lactic acid based scaffolds in a critical-sized cranial defect

Degradable polymer networks formed by the photoinitiated polymerization of multifunctional monomers have great potential as in situ forming materials, especially for bone tissue engineering. In this study, one specific chemistry was analyzed with respect to bone formation in a critical-sized defect model with and without adsorbed osteoinductive growth factors present. The scaffolds degraded in approximately 8 months and possessed an elastic modulus similar to that of trabecular bone. A porous scaffold fabricated with approximately 80% porosity and pore diameters ranging from 45 to 150 mm was implanted in a critical-sized cranial defect in rats. When implanted alone, the scaffolds were filled primarily with fibrous tissue after 9 weeks with only mild inflammation at the defect site. When the scaffolds released osteoinductive growth factors, statistically more bone filled the scaffold. For instance, 65.8+/-9.4% (n=5) of the defects were filled with radiopaque tissue in the osteoinductive releasing scaffolds, whereas only 24.2+/-7.4% (n=5) of the defects were filled in the untreated defects 9 weeks after implantation. These results illustrate not only the benefits of delivering osteoinductive factors when developing synthetic bone grafts, but the potential of these materials for supporting the infiltration and development of bone in large defects.     

聚DL-乳酸/羟基磷灰石复合材料修复长骨缺损的实验研究

目的 :评价羟基磷灰石 (HA)复合聚DL 乳酸 (PDLLA )制备的材料体内成骨能力。方法 :将PDLLA和PDLLA/HA( 2 0wt % )材料采用盐结晶颗粒沥滤法制成三维多孔材料 ,45例 1cm兔桡骨去骨膜缺损分为三组 ,分别植入 2种材料和作空白对照 ,术后 2 ,4,8,12周行X线、组织学及扫描电镜观察骨生成状况 ,8、12周行生物力学测试 (三点折弯强度 )。结果 :泡沫状PDLLA/HA ( 2 0wt % )材料比纯PDLLA成骨更好 (P <0 .0 5 ) ,实验组与对照组相比差异有显著性 (P <0 .0 5 )。结论 :PDLLA具有良好的生物相容性 ,制成多孔状具有较好的骨传导性能 ,HA( 2 0wt % )的加入促进了多孔PDLLA的骨传导能力 ,提高了骨生成的质量。PDLLA/HA( 2 0wt % )复合材料是一种有临床应用前景的骨移植材料。     

In vivo evaluation of a novel porous hydroxyapatite to sustain osteogenesis of transplanted bone marrow-derived osteoblastic cells

Biosynthetic bone grafts are considered to contain one or more of three critical components: osteoprogenitor cells, an osteoconductive matrix, and osteoinductive growth factors. The basic requirements of the scaffold material are biocompatibility, mechanical integrity, and osteoconductivity. A major design problem is satisfying these requirements with a single composite. In this study, we hypothesize that one composite that combines bone marrow-derived osteoblasts and a novel mechanical reinforced porous hydroxyapatite with good biocompatibility and osteoconductivity (HA/BMO) can reach these requirements. A novel sintered porous hydroxyapatite (HA) was prepared by the following procedures. The HA slurry was foamed by adding polyoxyethylenelaurylether (PEI) and mixing. The pores were fixed by crosslinking PEI with diepoxy compounds and the HA porous body was sintered at 1200 degrees C for 3 h. The HA sintered porous body had a high porosity (77%), and was completely interconnected. Average pore diameter was 500 microm and the interconnecting path 200 microm in diameter. The compressive (17 MPa) and three-point bending (7 MPa) strengths were high. For in vivo testing, the 2-week subcultured HA/BMO (+) composites were implanted into subcutaneous sites of syngeneic rats until 8 weeks after implantation. These implants were harvested at different time points and prepared for the biochemical analysis of alkaline phosphatase activity (ALP) and bone osteocalcin content (OCN), and histological analysis. ALP and OCN in the HA/BMO group were much higher than those in the HA without BMOs control group 1 week after implantation (p < 0.001). Light microscopy revealed mature bone formation in the HA/BMO composite 4 weeks after implantation. In the SEM study, mineralized collagenous extracellular matrix was noted in HA/BMO composite 2 weeks after implantation with numbers of active osteoblasts. We conclude that the composite of the novel HA and cultured BMOs has osteogenic ability in vivo. These results provide a basis for further studies on the use of this composite as an implant in orthopaedic surgery.     

Bone augmentation by bone marrow mesenchymal stem cells cultured in three-dimensional biodegradable polymer scaffolds

Poly-lactic-glycolic acid (PLGA) is a biocompatible as well as biodegradable polymer and used in various medical applications. In this study, we evaluated efficiency of the specially designed three-dimensional porous PLGA as a scaffold for bone augmentation. First, cell attachment/proliferation, differentiation, and mineralization of Fisher 344 rat marrow mesenchymal stem cells (MSCs) cultured on the PLGA scaffold were analyzed. Viable MSCs were impregnated into pore areas of the scaffold and a moderate increase of DNA contents was seen. High alkaline phosphatase, osteocalcin content, and calcium content of MSCs in PLGA scaffolds under osteogenic differentiation conditions were seen after 14 or 21 days of culture. Subsequently, we implanted the PLGA/MSCs composites on rat calvaria bone for 30 days. Newly formed bone was seen in only the composite PLGA/MSCs implantation group, which had been precultured under osteogenic condition. We also demonstrated that the newly formed bone originated from the donor composites. These results demonstrate that the three-dimensional PLGA scaffold can support osteogenic differentiation of MSCs, and the scaffold combined with osteogenic MSCs can be used for in vivo bone tissue augmentation.     

磷酸钙骨水泥复合骨形态发生蛋白6和血管内皮生长因子修复骨缺损

背景：单独将骨形态发生蛋白或血管内皮生长因子植入体内易被血液冲刷掉而不能最大限度发挥诱导成骨和血管生成作用,同时缺少载体的支撑作用。 目的：观察骨形态发生蛋白6、血管内皮生长因子及磷酸钙骨水泥联合应用在骨缺损修复过程中的作用。 方法：制作新西兰兔双侧股骨内侧髁骨缺损模型,左侧分别植入磷酸钙骨水泥/骨形态发生蛋白6/血管内皮生长因子、磷酸钙骨水泥/骨形态发生蛋白6及磷酸钙骨水泥,右侧不植入任何物质作为空白对照。植入8,16周通过硬组织切片组织学观察、电镜扫描等手段观察新骨形成情况。 结果与结论：各组材料的组织相容性良好,未见明显炎症组织反应。植入8周时,磷酸钙骨水泥/骨形态发生蛋白6/血管内皮生长因子组骨水泥-骨组织交界处基本上被新生骨小梁包绕,材料进一步降解,新生骨小梁表面可见大量活跃的成骨细胞;16周时,新生骨小梁继续长入,进一步增长、增粗、增多,有大量新生编织骨成网格状长入材料中,骨水泥材料降解明显,与周围组织结合紧密,降解与骨长入同步,此组不同时间点成骨速度及成骨效果均明显优于其他两组材料(P < 0.05)。表明3种材料联合应用可协同促进骨缺损修复。中国组织工程研究杂志出版内容重点：生物材料;骨生物材料; 口腔生物材料; 纳米材料; 缓释材料; 材料相容性;组织工程全文链接：     

Histomorphometric study on high-strength hydroxyapatite/poly(L-lactide) composite rods for internal fixation of bone fractures

The purpose of this study was to investigate the bone-implant interface of high-strength hydroxyapatite (HA)/poly(L-lactide) (PLLA) composite rods. As reinforcing particles, two types of HA particles-calcined HA (c-HA) and uncalcined HA (u-HA)-were applied to allow comparison of their suitability as bioactive fillers. Four types of composites (c-HA30, c-HA40, u-HA30, and u-HA40), which contained 30 or 40% by weight of each HA particle, were used. Unfilled PLLA rods were used as controls. A hole was drilled in the distal femora of 50 rabbits, and a composite or unfilled PLLA rod was implanted in a press-fit manner. Two, 4, 8, and 25 weeks after implantation, the samples were examined histologically by light microscopy, scanning electron microscopy (SEM), and transmission electron microscopy (TEM). An image analyzer was used for histomorphometric analysis of the bone-implant interface. An affinity index was calculated for each material; this was the length of bone directly apposed to the rods expressed as a percentage of the total length of the rod surface. In all the composites, histologic examination showed new bone formation at 2 weeks after implantation. The bone gradually grew along the composite surface. SEM showed direct bone contact with the composites without intervening fibrous tissue. During follow-up, the affinity indices of all the composite rods were significantly higher than those of the unfilled PLLA rods (p < 0.01; two-way ANOVA). The maximum affinity index (41%) was attained at 4 weeks in c-HA40 rods. In contrast, little bone contact was seen in unfilled PLLA rods. The only significant difference in affinity indices among the composites was that c-HA40 had a higher affinity index than u-HA40 (p < 0.05 at 4 weeks). No disintegration of rods or polymer debris, which could elicit inflammatory tissue reactions, was observed even at 25 weeks. Our results indicate that osteoconductive bone formation on composites could enhance the stability between bone and implant in fracture repair.     

Bone tissue engineering with porous hydroxyapatite ceramics

The main principle of bone tissue engineering strategy is to use an osteoconductive porous scaffold in combination with osteoinductive molecules or osteogenic cells. The requirements for a scaffold in bone regeneration are: (1) biocompatibility, (2) osteoconductivity, (3) interconnected porous structure, (4) appropriate mechanical strength, and (5) biodegradability. We recently developed a fully interconnected porous hydroxyapatite (IP-CHA) by adopting the “form-gel” technique. IP-CHA has a three-dimensional structure with spherical pores of uniform size that are interconnected by window-like holes; the material also demonstrated adequate compression strength. In animal experiments, IP-CHA showed superior osteoconduction, with the majority of pores filled with newly formed bone. The interconnected porous structure facilitates bone tissue engineering by allowing the introduction of bone cells, osteotropic agents, or vasculature into the pores. In this article, we review the accumulated data on bone tissue engineering using the novel scaffold, focusing especially on new techniques in combination with bone morphogenetic protein (BMP) or mesenchymal stem cells.     

Bonding behavior of ultrahigh strength unsintered hydroxyapatite particles/poly(L-lactide) composites to surface of tibial cortex in rabbits.

Unsintered hydroxyapatite particles/poly(L-lactide) (u-HA/PLLA) composites with an initial bending strength of up to 270 MPa were developed based on the hypothesis that inclusion of u-HA particles in a PLLA matrix might enhance bone bonding. The purpose of this study was to examine the bonding strength and behavior of these u-HA/PLLA composites on the surface of the bone cortex. Composites containing 30 (u-HA30), 40 (u-HA40), or 50 wt % (u-HA50) of fine u-HA particles (3-microm average particle size) were prepared. Semicolumnar plates of these composites and control PLLA plates were fixed with metal screws to the surface of both proximal tibial cortices in 45 rabbits. The loads required to detach the plates from the bone cortex surface, defined as the bonding strengths, were measured at 4, 8, and 25 weeks after implantation. Bonding strengths in the u-HA30 group at 8 weeks and in the u-HA40 and u-HA50 groups at each postimplantation time were significantly greater than in the PLLA group (post hoc test using Fisher's protected least significant difference method). At each postimplantation time histological examinations revealed direct contact between the bone and the u-HA/PLLA composite plates without any intervening fibrous tissue. There was no evidence of any inflammatory or foreign-body response in any group throughout the follow-up periods. The results of this study suggest that the biodegradable PLLA fixation plates amended with u-HA particles could be functionally superior to PLLA plates without particles.     

骨髓基质干细胞复合煅烧骨的皮下成骨

背景：研究证明骨髓基质干细胞与煅烧骨支架材料结合后可形成组织工程化骨,但在动物体内的生物相容性及皮下诱导成骨的能力国内报道较少。 目的：观察骨髓基质细胞复合异种煅烧骨植入BALB/c裸鼠背部皮下的成骨性能及煅烧骨材料作为组织工程骨支架材料的可行性。 方法：选用经脱脂及脱蛋白处理后高温煅烧形成的骨支架材料与梯度密度离心法分离培养至第3代的羊骨髓基质干细胞构建细胞-煅烧骨复合物植入BALB/c裸鼠背部皮下,选同期对侧背部皮下植入单纯煅烧骨为对照组。 结果与结论：煅烧后的松质骨块为白垩色,表面呈蜂窝状多孔结构,保留了天然松质骨的多孔状空间结构。骨小梁结构完整,孔隙相互连通。骨髓基质干细胞接种到煅烧骨后24 h可见大量细胞黏附于支架上,7 d后细胞分泌大量细胞外基质,细胞与基质分界不清,细胞能在材料上良好地黏附、增殖与生长,细胞活性未受到支架材料的影响。植入4周后,两组均可见煅烧骨边缘出现少量残片,细胞-煅烧骨复合物组煅烧骨孔隙周边可发现骨细胞,对照组煅烧骨表面可见纤维结缔组织包绕。植入后8周,两组均可见到煅烧骨部分降解为片状类骨质,周围有成纤维细胞包绕,排列紧密,形态多样,细胞-煅烧骨复合物组煅烧骨孔隙内可见煅烧骨表面有排列成行的成骨细胞,孔隙间有散在淋巴细胞浸润。对照组标本可见孔隙内有大量结缔组织长入,未见明显成骨迹象。结果说明,经高温煅烧后的松质骨材料,具有良好的生物相容性和生物安全性,可作为骨髓基质干细胞的良好载体,复合后植入体内能够诱导新生骨组织形成,可作为骨缺损组织工程修复的支架材料。     

The pro-angiogenic properties of multi-functional bioactive glass composite scaffolds

The angiogenic properties of micron-sized (m-BG) and nano-sized (n-BG) bioactive glass (BG) filled poly(D,L lactide) (PDLLA) composites were investigated. On the basis of cell culture work investigating the secretion of vascular endothelial growth factor (VEGF) by human fibroblasts in contact with composite films (0, 5, 10, 20 wt %), porous 3D composite scaffolds, optimised with respect to the BG filler content capable of inducing angiogenic response, were produced. The in vivo vascularisation of the scaffolds was studied in a rat animal model and quantified using stereological analyses. The prepared scaffolds had high porosities (81-93%), permeability (k = 5.4-8.6 x 10?? m2) and compressive strength values (0.4-1.6 MPa) all in the range of trabecular bone. On composite films containing 20 wt % m-BG or n-BG, human fibroblasts produced 5 times higher VEGF than on pure PDLLA films. After 8 weeks of implantation, m-BG and n-BG containing scaffolds were well-infiltrated with newly formed tissue and demonstrated higher vascularisation and percentage blood vessel to tissue (11.6-15.1%) than PDLLA scaffolds (8.5%). This work thus shows potential for the regeneration of hard-soft tissue defects and increased bone formation arising from enhanced vascularisation of the construct.     

骨诱导性磷酸钙陶瓷材料修复牙槽突裂

BACKGROUND: In our previous studies, we had prepared calcium phosphate ceramics with better ectopic osteogenesis. OBJECTIVE: To explore the effect of novel osteoinductive calcium phosphate ceramics in the repairing of alveolar cleft. METHODS: Bilaterl alveolar defects were created in nine immature beagles. Three months later, osteoinductive calcium phosphate ceramics with high modular surface (experimental group) and smooth surface (control group) were randomly implanted in each side of the defect. Meanwhile, the corresponding material was implanted into the thigh muscle. New bone formation in the implanted region, osteogenesis in the implanted region and muscle, and respair results were respectively observed by fluorescence microscope, light microscope and CT at 4, 8 and 12 weeks after implantation. RESULTS AND CONCLUSION: (1) Fluorescence microscope observation: A circular permutation of red, yellow and green fluorescent strip could be observed in both two groups. (2) Light microscope observation: At 12 weeks after implantation, in the experimental group, the bone reconstruction was obvious, the implant material was decomposed gradually, the gap was filled with a large number of mature bone that combined with the rest material closely, and numerous Haversian canals appeared; the control group was similar but slightly inferior to the experimental group in the quality of new bone. The experimental group material successfully induced heterotopic osteogenesis in muscle, while the control did not. (3) CT examination: The two group materials restored the appearance and continuity of the alveolar ridge, and made no effect on the eruption of permanent teeth in both sides of the defect. To conclude, our findings suggest that the novel osteoinductive calcium phosphate ceramic exhibits advantages in alveolar cleft repair with earlier osteogenesis activation, faster osteogenesis rate and more bone formation than those traditional materials.     

Demineralized dentin matrix composite collagen material for bone tissue regeneration

Demineralized dentin matrix (DDM) had been successfully used in clinics as bone repair biomaterial for many years. However, particle morphology of DDM limited it further applications. In this study, DDM and collagen were prepared to DDM composite collagen material. The surface morphology of the material was studied by scanning electron microscope (SEM). MC3T3-E1 cells responses in vitro and tissue responses in vivo by implantation of DDM composite collagen material in bone defect of rabbits were also investigated. SEM analysis showed that DDM composite collagen material evenly distributed and formed a porous scaffold. Cell culture and animal models results indicated that DDM composite collagen material was biocompatible and could support cell proliferation and differentiation. Histological evaluation showed that DDM composite collagen material exhibited good biocompatibility, biodegradability and osteoconductivity with host bone in vivo. The results suggested that DDM composite collagen material might have a significant clinical advantage and potential to be applied in bone and orthopedic surgery.     

New scaffold for recombinant human bone morphogenetic protein-2

A bioactive and resorbable scaffold is necessary to exhibit the osteoinductive potency of recombinant human bone morphogenetic protein-2 (rhBMP-2). In a previous study, we found that synthetic octacalcium phosphate (OCP) enhances bone regeneration and is replaced by newly formed bone after it is resorbed. We hypothesized that OCP may be useful as an effective scaffold for rhBMP-2 to enhance bone regeneration. To test this hypothesis, the present study was designed to investigate whether an OCP/BMP composite implant could more effectively enhance bone regeneration. A critical-sized defect was made in a rat calvarium and 1. 15 mg of OCP combined with 10 microg of rhBMP-2 (OCP/BMP 10 microg), 2. 15 mg of OCP combined with 1 microg of rhBMP-2 (OCP/BMP 1 microg), or 3. OCP (OCP alone) was implanted into the defect and fixed at 4 or 8 weeks after implantation. The percentage of newly formed bone (n-Bone%) in the defect was determined by a histomorphometrical analysis. A statistical analysis showed that n-Bone% with OCP/BMP was significantly higher than that with OCP at both time points, whereas the difference in n-Bone% between OCP/BMP 10 microg and OCP/BMP 1 microg was not significant. The present results suggest that OCP can be used as an effective scaffold for rhBMP-2 and this OCP delivery system may be able to reduce the standard effective dose of rhBMP-2, which would be beneficial because low doses (<100 microg/g OCP) of rhBMP-2 enhance bone regeneration.     

Mesenchymal stem cell-based repair of articular cartilage with polyglycolic acid-hydroxyapatite biphasic scaffold

This study investigates the capacity of a composite scaffold composed of polyglycolic acid-hydroxyapatite (PGA-HA) and autologous mesenchymal stem cells (MSCs) to promote repair of osteochondral defects. MSCs from culture-expanded rabbits were seeded onto a PGA and HA scaffold. After a 72-hour co-culture period, the cell-adhered PGA and HA were joined together, forming an MSCs-PGA-HA composite. Full-thickness cartilage defects in the intercondylar fossa of the femur were then implanted with the MSC-PGA-HA composite, the PGA-HA scaffold only, or they were left empty (n=20). Animals were sacrificed 16 or 32 weeks after surgery and the gross appearance of the defects was evaluated. The specimens were examined histologically for morphologic features, and stained immunohistochemically for type 2 collagen. Specimens of the MSCs-PGA-HA composite implantation group demonstrated hyaline cartilage and a complete subchondral bone formation. At 16 weeks post-implantation, significant integration of the newly formed tissue with surrounding normal cartilage and subchondral bone was observed when compared to the two control groups. At 32 weeks, no sign of progressive degeneration of the newly formed tissue was found. A significant difference in histological grading score was found compared with the control groups. The novel MSCs-seeded, PGA-HA biphasic graft facilitated both articular cartilage and subchondral bone regeneration in an animal model and might serve as a new approach for clinical applications.     

The effects of a novel-reinforced bone substitute and Colloss®E on bone defect healing in sheep

Hydroxyappatite-β-tricalciumphosphate (HA/β-TCP) was reinforced with poly(D,L)-lactic acid (PDLLA) to overcome its weak mechanical properties. Two substitutes with porosities of 77% and 81% HA/β-TCP reinforced with 12 wt % PDLLA were tested in compression. The effects of allograft, substitute (HA/β-TCP-PDLLA), Colloss?E, and combination of substitute with Colloss?E on bone formation in vivo were evaluated. Cylindrical critical size defects were created at distal femoral condyles bilaterally in sheep. Titanium implant with concentric gap filling with one of the four materials was inserted. After 9 weeks, the sheep were sacrificed. Implants with surrounding bone were harvested and sectioned into two parts: one for microcomputed tomography scanning and push-out test, and one for histomorphometry. The 77% HA/β-TCP reinforced with PDLLA had similar mechanical properties to human cancellous bone and was significantly stronger than the HA/β-TCP without PDLLA. Microarchitecture of gap mass was significantly changed after implantation for all groups. Allograft had stronger shear mechanical properties than the other three groups, whereas there were no significant differences between the other three groups. Significant new bone formation could be seen in vivo in all four groups and there were no significant differences between them. The PDLLA-reinforced substitute seems to be good alternative substitute material for bone healing in sheep. Further investigations should be performed to validate this novel substitute material. ? 2012 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2012.     

In vitro and in vivo evaluation of a novel nanosize hydroxyapatite particles/poly(ester-urethane) composite scaffold for bone tissue engineering

Scaffolds for bone tissue engineering should provide an osteoconductive surface to promote the ingrowth of new bone after implantation into bone defects. This may be achieved by hydroxyapatite loading of distinct scaffold biomaterials. Herein, we analyzed the in vitro and in vivo properties of a novel nanosize hydroxyapatite particles/poly(ester-urethane) (nHA/PU) composite scaffold which was prepared by a salt leaching–phase inverse process. Microtomography, scanning electron microscopy and X-ray spectroscopy analyses demonstrated the capability of the material processing to create a three-dimensional porous PU scaffold with nHA on the surface. Compared to nHA-free PU scaffolds (control), this modified scaffold type induced a significant increase in in vitro adsorption of model proteins. In vivo analysis of the inflammatory and angiogenic host tissue response to implanted nHA/PU scaffolds in the dorsal skinfold chamber model indicated that the incorporation of nHA particles into the scaffold material did not affect biocompatibility and vascularization when compared to control scaffolds. Thus, nHA/PU composite scaffolds represent a promising new type of scaffold for bone tissue engineering, combining the flexible material properties of PU with the advantage of an osteoconductive surface.     

In vivo mineralization and osteogenesis of nanocomposite scaffold of poly(lactide-co-glycolide) and hydroxyapatite surface-grafted with poly(L-lactide)

Nanocomposite of hydroxyapatite (HAP) surface-grafted with poly(l-lactide) (PLLA) (g-HAP) shows a wide application for bone fixation materials due to its improved interface compatibility, mechanical property and biocompatibility in our previous study. In this paper, a 3-D porous scaffold of g-HAP/poly(lactide-co-glycolide) (PLGA) was fabricated using the solvent casting/particulate leaching method to investigate its applications in bone replacement and tissue engineering. The composite of un-grafted HAP/PLGA and neat PLGA were used as controls. Their in vivo mineralization and osteogenesis were investigated by intramuscular implantation and replacement for repairing radius defects of rabbits. After surface modification, more uniform distribution of g-HAP particles but a lower calcium exposure on the surface of g-HAP/PLGA was observed. Intramuscular implantation study showed that the scaffold of g-HAP/PLGA was more stable than that of PLGA, and exhibited similar mineralization and biodegradability to HAP/PLGA at the 12-20 weeks post-surgery. The implantation study for repairing critical radius defects showed that the scaffold of g-HAP/PLGA exhibited rapid and strong mineralization and osteoconductivity, and the incorporation of BMP-2 could enhance the osteogenic process of the composite implant. The new bone formation with the intact structure of a long bone was guided by the implant of g-HAP/PLGA.