Biomechanical and histomorphometric study of dental implants with different surface characteristics

The aim of this study was to investigate the early bone response to the titanium dental implants with different surface characteristics using the rabbit tibia model. Calcium metaphosphate coated, anodic oxidized, hydroxyapatite particle-blasted, and turned (control) surfaces were compared. Surface topography was evaluated by field emission scanning electron microscope and optical interferometer. Eighteen rabbits received 72 implants in the tibia. Resonance frequency was analyzed every week for 6 weeks. Removal torque values were measured 2 and 6 weeks after placement. The implant-bone interfaces were directly observed by light microscope and bone-to-implant contact ratios were measured 2 and 6 weeks after insertion. All the surface-modified implants showed superior initial bone responses to the control. No significant differences were found among the surface-modified groups. Data suggest that various surface modification methods can provide favorable bone responses for early functioning and healing of dental implants.     

Biomechanical and histomorphometric analysis of etched and non-etched resorbable blasting media processed implant surfaces: An experimental study in dogs

This study characterized the interplay between topography/chemistry and early bone response of etched and no-etched resorbable blasted media (RBM) processed surfaces. Screw-root form Ti–6Al–4V implants treated with alumina blasting/acid-etching (AB/AE), RBM alone (RBM), and RBM + acid-etching (RBMa) were evaluated. The surface was characterized by scanning electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. Implants placed in the tibia of dogs remained 3 and 5 weeks in vivo. Following euthanasia, half of the specimens were torqued to interface failure and the remaining subjected to bone-to-implant contact (BIC) and bone area fraction occupied (BAFO) between threads evaluation. The AB/AE surface was rougher than the RBM and RBMa. Higher levels of calcium and phosphorous were observed for the RBM surface compared to the RBMa. No significant differences were observed in torque, BIC, and BAFO between surfaces. Woven bone formation at 3 weeks and its initial replacement by lamellar bone at 5 weeks were observed around all implants’ surfaces.     

Bone response to endosseous titanium implants surface-modified by blasting and chemical treatment: a histomorphometric study in the rabbit femur

This study evaluated the effects of the addition of oxide structure with submicron-scale porous morphology on the periimplant bone response around titanium (Ti) implants with microroughened surfaces. Hydroxyapatite-blasted Ti implants with (experimental) and without (control) a porous oxide structure produced by chemical treatment were investigated in a rabbit femur model. Surface characterizations and in vivo bone response at 4 and 8 weeks after implantation were compared. The experimental implants had submicron-scale porous surface structure consisted of anatase and rutile phase, and the original R(a) values produced by blasting were preserved. The histomorphometric evaluation demonstrated statistically significantly increased bone-to-implant contact (BIC) for experimental implants, both in the three best consecutive threads (p < 0.01) and all threads (p < 0.05) at 4 weeks. There was no remarkable difference in the BIC% or bone area percentage between the two groups at 8 weeks. The porous Ti oxide surface enhanced periimplant bone formation around the Ti implants with microroughened surfaces at the early healing stage. Based on the results of this study, the addition of crystalline Ti oxide surface with submicron-sized porous morphology produced by chemical treatment may be an effective approach for enhancing the osseointegration of Ti implants with microroughened surfaces by increasing early bone-implant contact.     

Biological assessment of the bone-screw interface after insertion of uncoated and hydroxyapatite-coated pedicular screws in the osteopenic sheep

The sheep seems to be a promising model of osteoporosis and biomaterial osteointegration in osteopenic bone. The long-term ovariectomized sheep model was used for the biological investigation of bone healing around uncoated and hydroxyapatite (HA)-coated pedicle screws in osteopenic bone. Four sheep were ovariectomized and four sheep were sham-operated. Twenty-four months after surgery, the animals were implanted with uncoated and HA-coated stainless steel screws in the lumbar vertebral pedicles. Four months later, bone-to-implant contact, bone ingrowth, and bone hardness were measured around screws. Uncoated stainless steel presented significantly (p < 0.0005) lower bone-to-implant contact in healthy and osteopenic bone compared with HA-coated stainless steel. HA significantly improved bone ingrowth in healthy bone (p < 0.05) compared with uncoated stainless steel. Osteopenia significantly (p < 0.05) reduced the area of bone ingrowth around the screw threads for both types of implants. In the inner thread area, bone microhardness significantly increased (p < 0.05) in HA-coated surface versus uncoated for healthy and osteopenic bone. HA coating significantly enhances bone-to-implant contact also in osteopenic bone in comparison with uncoated stainless steel surfaces. Bone ingrowth and mineralization are ameliorated by the osteoconductive HA coating. However, osteopenia seems to greatly influence bone ingrowth processes around the implanted screws regardless of the characteristics of the material surface.     

Healing of complement activating Ti implants compared with non-activating Ti in rat tibia

Recent studies have revealed that ozone ultraviolet (UVO) illumination of titanium (Ti) implants improves bone-implant anchorage by altering the physico-chemical and immune activating properties of the titanium dioxide (TiO(2)) layer. In the present rat tibia model, the authors compared the early events of inflammation and bone formation around UVO-treated Ti and complement activating immunoglobin g (IgG)-coated Ti. Machined Ti and machined Ti coated with a physical vapour-deposited Ti layer were used as references. Screw-shaped test and reference implants were implanted into rat tibia and harvested after 1, 7 and 28 days. Messenger RNA expression of implant adhered cells and peri-implant tissue ~250 μm from the surface were subsequently analysed with regard to IL-1β, TNF-α, osteocalcin, cathepsin K, BMP-2 and PDGF. Separate implants were retrieved after 7 and 28 days for removal torque measurements, and histological staining and histomorphometric analysis of bone area and bone-to-implant contact. While enhanced expression of inflammatory markers, TNF-α and IL-1β, was observed on IgG-coated surfaces throughout the observation time, UVO-treated surfaces indicated a significantly lower early inflammatory response. In the early phases (1 and 7 days), the UVO-treated surfaces displayed a significantly higher expression of osteoblast markers BMP-2 and osteocalcin. In summary, complement activating Ti implants elicited a stronger inflammatory response than UVO-treated Ti, with low complement activation during the first week of healing. In spite of this, the UVO-treated Ti induced only marginally more bone growth outside the implants.     

No increased bone formation around alendronate or omeprazole loaded bioactive bone cements in a femoral defect

Alendronate and omeprazole have been found to influence bone healing by interfering with osteoclastic activity, resulting in increased bone formation. The biological effect of these conventional drugs, incorporated into bioactive bone cement (G2B1), was investigated in a rabbit model. The 2 materials and a control were inserted in defects created in the femoral condyle of rabbits. Implantation time was 6 and 12 weeks. After retrieval, micro-computed tomography and histomorphometry were performed to quantify bone mineral density (BMD) and bone volume (BV) of the implant-surrounding bone mass and the percentage of bone-to-implant contact. BMD and BV were similar in all groups. The percentage of bone-to-implant contact was significantly lower in the alendronate and omeprazole groups than in controls after 6 weeks of implantation. After 12 weeks, this difference in bone contact disappeared for the omeprazole but not for the alendronate implants, which were almost completely surrounded by a fibrous capsule, associated with a limited inflammatory response. In conclusion, in the current study, alendronate and omeprazole did not result in better bone healing when incorporated into bioactive bone cement than did plain control implants. Moreover, an additional cytotoxicity assay revealed that alendronate evoked a toxic response.     

The importance of surface texture for bone integration of screw shaped implants: an in vivo study of implants patterned by photolithography

The aim of the present study was to investigate the influence of different properties inherent in surface topography on the integration of an implant in bone. Using a photolithography technique, a specific surface pattern was produced on the screw flanks of threaded titanium oral implants. Surface topography was qualitatively assessed by scanning electron microscopy (SEM) and a confocal laser scanning profilometer. Quantitative analysis with the confocal laser profilometer derived parameters for surface roughness and surface roughness together with waviness. The chemical composition of the implant surfaces was analyzed by Auger electron spectroscopy. The patterned and control (turned) implants were inserted in New Zealand White rabbits with a healing period of 3 months. Bone fixation was evaluated with resonance frequency analysis (RFA), peak removal torque analysis (RTQ), and by histomorphometry. No statistically significant differences were seen in the fixation, with respect to bone-to-implant contact, between the patterned and control implants.     

In vivo evaluation of bone-bonding ability of RGD-coated porous implant using layer-by-layer electrostatic self-assembly

RGD has been demonstrated to improve implant osseointegration. However, few studies are known about an effect of RGD coating on a bone-bonding ability of screw-shaped porous implant. The aim of this study was to investigate the effect of RGD coating using the layer-by-layer self-assembly technique on the bone-bonding ability of porous implant. 60 implants of 10 mm in length (30 control and 30 RGD-coated) were inserted into femurs of 30 rabbits and 30 implants of 8 mm in length (15 control and 15 RGD-coated) were inserted into tibias of 15 rabbits. At 4, 8, and 12 weeks post-implantation, femurs and tibias were retrieved and prepared for removal torque tests (RTQ) and histomorphometric evaluation, respectively. No differences were found in the RTQ values between two implants at 4 weeks (p = 0.932). There were statistical significances in the RTQ values at 8 and 12 weeks (p = 0.002, 0.001, respectively). New bone was formed on both implant surfaces. The bone-implant contact pattern appeared to produce a broad-based direct contact in both implants. The RGD-coated implants showed a significantly greater BIC in the threads inside the cortical bone compared with the control implants at 4, 8, and 12 weeks (p = 0.024, 0.041, 0.022, respectively). No differences were found in the bone area within the same threads between two implants at 4 weeks (p = 0.806) whereas differences were found at 8 and 12 weeks (p = 0.009, 0.031, respectively). It was concluded that RGD coating using the layer-by-layer self-assembly technique has a positive effect on the bone-bonding ability of porous implant.     

Biomechanical and histomorphometric investigations on two morphologically differing titanium surfaces with and without fluorohydroxyapatite coating: an experimental study in sheep tibiae

The influence of fluorohydroxyapatite (FHA) coating and surface roughness of Ti6Al4V implants on bone response was investigated. Uncoated and FHA-coated screws with lower (LR and LR+FHA; Ra: 5.7+/-0.2 microm) and higher (HR and HR+FHA; Ra: 21.8+/-0.9 microm) surface roughness, were inserted into the diaphyses of 8 sheep tibiae. Twelve weeks after implantation, extraction torque and bone-to-implant contact were evaluated. The smoothest surfaces showed an improved extraction torque and significant differences were observed between LR and HR (-24.6%, p<0.0005), LR and HR+FHA (-30.7%, p<0.0005), LR+FHA and HR (-17.4%, p<0.005), and LR+FHA and HR+FHA (-24.0%, p<0.005). The bone-to-implant contact data paralleled the biomechanical data: the smoother the surface, the greater the bone-to-implant contact. Significant (p<0.0005) decreases in bone-to-implant contact were observed between LR+FHA and HR (-24.2%), and between LR+FHA and HR+FHA (-29.2%). The current findings suggest that LR surfaces significantly improve the osteointegration rate of implanted cortical screws independently of the FHA coating.     

Long-term rabbits bone response to titanium implants in the presence of inorganic bovine-derived graft

This study evaluated bone responses to titanium implants in the presence of an inorganic graft material. The bilateral mandible incisors of 24 rabbits were surgically extracted and one of the exposed sockets, chosen at random, was filled with an inorganic xenogenic bone graft (Gen-ox?), whereas the remaining socket was left to heal naturally and served as a control. After 60 days, titanium implants were inserted in the specific areas, and on days 0, 30, 60, and 180 after the implant insertions, six animals of each group were killed. Digital periapical radiography of implant region was obtained and vertical bone height (VBH) and bone density (BD) were evaluated by digital analysis system. In the undecalcified tissue cuts, bone-to-implant contact (BIC) and bone area (BA) within the limits of the implant threads were evaluated and compared statistically by means of two-way ANOVA and Tukey's test (ρ < 0.05). No significant differences were detected in VBH and BA, either between groups or between different experimental intervals. The BD was significantly higher in the experimental group than in the control group in all the intervals tested, but there were no significant differences by interval. The BIC was statistically lower in the control group on day 0; however, a significant increase was observed on days 60 and 180 (ρ < 0.05). The use of an inorganic xenograft prior to insertion of a titanium implant did not interfere with the course of osseointegration.     

Osteoconductivity of hydrophilic microstructured titanium implants with phosphate ion chemistry

This study investigated the surface characteristics and bone response of titanium implants produced by hydrothermal treatment using H₃PO₄, and compared them with those of implants produced by commercial surface treatment methods – machining, acid etching, grit blasting, grit blasting/acid etching or spark anodization. The surface characteristics were evaluated by scanning electron microscopy, thin-film X-ray diffractometry, X-ray photoelectron spectroscopy, contact angle measurement and stylus profilometry. The osteoconductivity of experimental implants was evaluated by removal torque testing and histomorphometric analysis after 6 weeks of implantation in rabbit tibiae. Hydrothermal treatment with H₃PO₄ and subsequent heat treatment produced a crystalline phosphate ion-incorporated oxide (titanium oxide phosphate hydrate, Ti₂O(PO₄)₂(H₂O)₂; TiP) surface approximately 5 μm in thickness, which had needle-like surface microstructures and superior wettability compared with the control surfaces. Significant increases in removal torque forces and bone-to-implant contact values were observed for TiP implants compared with those of the control implants (p < 0.001). After thorough cleaning of the implants removed during the removal torque testing, a considerable quantity of attached bone was observed on the surfaces of the TiP implants.     

Different patterns of bone fixation with hydroxyapatite and resorbable CaP coatings in the rabbit tibia at 6, 12, and 52 weeks

Applying bioactive coatings on orthopedic implants can increase the fixation and long-term implant survival. In our study, we compared a resorbable electrochemically deposited calcium phosphate coating (Bonit?) to a thin (40 μm) plasma-sprayed hydroxyapatite (HA) coating, applied on grit-blasted screw-shaped Ti-6Al-4V implants in the cortical region of rabbit tibia, implanted for 6, 12, and 52 weeks. The removal torque results demonstrated stronger bone-to-implant fixation for the HA than Bonit-coated screws at 6 and 12 weeks. After 52 weeks, the fixation was in favor of the Bonit-coated screws, but the difference was statistically insignificant. Coat flaking and delamination of the HA with multinucleated giant cell activity and bone resorption observed histologically seemed to preclude any significant increase in fixation comparing the HA implants at 6 versus 12 weeks and 12 versus 52 weeks. The Bonit-coated implants exhibited increasing fixation from 6 to 12 weeks and from 12 to 52 weeks, and the coat was resorbed within 6 weeks, with minimal activity of multinucleated giant cells or bone resorption. A different fixation pattern was observed for the two coatings with a sharper but time limited increase in fixation for the HA-coated screws, and a slower but more steadily increasing fixation pattern for the Bonit-coated screws. The side effects were more serious for the HA coating and limiting the expected increase in fixation with time.     

Hydroxyapatite coating affects the Wnt signaling pathway during peri-implant healing in vivo

Owing to its bio- and osteoconductivity, hydroxyapatite (HA) is a widely used implant material, but its osteogenic properties are only partly evaluated in vitro and in vivo. The present study focused on bone healing adjacent to HA-coated titanium (Ti) implants, with or without incorporated lithium ions (Li⁺). Special attention was given to the Wnt signaling pathway. The implants were inserted into rat tibia for 7 or 28 days and analyzed ex vivo, mainly by histomorphometry and quantitative real-time polymerase chain reaction (qPCR). HA-coated implants showed, irrespective of Li⁺ content, bone–implant contact (BIC) and removal torque values significantly higher than those of reference Ti. Further, the expression of OCN, CTSK, COL1A1, LRP5/6 and WISP1 was significantly higher in implant-adherent cells of HA-coated implants, with or without Li⁺. Significantly higher β-catenin expression and significantly lower COL2A1 expression were observed in peri-implant bone cells from HA with 14 ng cm⁻² released Li⁺. Interestingly, Ti implants showed a significantly larger bone area (BA) in the threads than HA with 39 ng cm⁻² released Li⁺, but had a lower BIC than any HA-coated implant. This study shows that HA, with or without Li⁺, is a strong activator of the Wnt signaling pathway, and may to some degree explain its high bone induction capacity.     

Collagen I-coated titanium surfaces: mesenchymal cell adhesion and in vivo evaluation in trabecular bone implants

The goal of the study was the evaluation of the effect of modification of titanium implants by acrylic acid surface grafting-collagen I coupling. Tests were performed on titanium samples treated by galvanostatic anodization to create a porous surface topography. Surface characterization by X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) confirms the biochemical modification of the surface and shows a surface topography characterized by pores mostly below 1 mum diameter. In vitro evaluation involving human mesenchymal cells shows enhanced cell growth on collagen coated surfaces as compared to titanium ones. Four weeks in vivo evaluation of implants in rabbit femur trabecular bone shows improvements of bone-to-implant contact, while improvement of bone ingrowth is slightly not significant (p = 0.056), when compared to the control. Overall, these data indicate that integration in trabecular, or cancellous, bone can be enhanced by the surface collagen layer, confirming previous findings obtained by modification of machined surfaces by the same approach in cortical bone implants.     

Osseointegration of hydroxyapatite-coated and noncoated Ti6Al4V implants in the presence of local infection: a comparative histomorphometrical study in rabbits

A study was designed to investigate the osseointegration of titanium implants, either noncoated or coated with hydroxyapatite (HA), into rabbit tibiae in the presence of local infection compared with osseointegration in the absence of local infection. HA-coated or noncoated Ti cylinders were implanted into both tibiae of 32 rabbits (New Zealand Whites). Before implantation the left tibia was contaminated with different quantities of Staphylococcus aureus (10(2)-10(5) CFU). Four weeks after surgery the tibiae were explanted and prepared for microbiological and histomorphometrical examination. Histomorphometrical data, as a representation of implant fixation, were obtained by measuring the percentage of bone around the implants (within a radius of 1 mm from the outer diameter of the implants) and the percentage of the circumference of the implant that was in direct contact with bone. Histomorphometry revealed, in particular for the HA implants, a relationship between the inoculum concentration and/or the presence or absence of infection with the bone contact at the distal implant side. This confirms a relationship between peri-implant infection and bone contact or remodeling. HA-coated implants developed, in the presence of bacteria, more easily a more severe infection than noncoated Ti implants, and we show in the present study that local infection will influence histomorphometrical parameters (bone-implant contact) that determine implant fixation. Precautions to prevent contamination (asepsis) and/or infection (perioperative antibiotics) are even more important for the highly biocompatible HA-coated implant.     

Bioactive glass microspheres as osteopromotive inlays in macrotextured surfaces of Ti and CoCr alloy bone implants: trapezoidal surface grooves without inlay most efficient in resisting torsional forces

We have tested the efficacy of porous bioactive glass (BG) inlays in enhancement of implant osseointegration. A total of 24 sheep underwent bilateral surgical implantation of three parallel implants on the anteromedial cortical surface of each tibia. The disc-shaped implants made of Ti6Al4V or cobalt chromium (CoCr) alloys had two parallel surface grooves (trapezoidal space with bottom widening) filled with sintered 100% bioactive glass microspheres or a selected mixture of bioactive and biocompatible glass microspheres. The surface of uncoated control implants was smooth, grit-blasted or had unfilled grooves. A subgroup of control smooth CoCr implants was coated with two or three BG layers. Implant incorporation with bone was evaluated using torque testing to failure, scanning electron microscopy and morphometry at 12 and 25 weeks. A total of 144 in vivo implants and 16 ex vivo cemented control implants were analyzed. Control Ti6Al4V implants with unfilled trapezoidal grooves showed highest torsional failure loads with excellent ingrowth of new bone and remodeling of ingrown bone into lamellar bone. Implants with BG inlays and microroughened control Ti6Al4V implants showed significantly lower torsional failure loads than control Ti6Al4V implants with unfilled grooves. In conclusion, BG inlays failed to enhance biological implant fixation. Macrotextured surface was more effective than grit-blasting in promotion of mechanical incorporation.     

Evaluation of chemically modified SLA implants (modSLA) biofunctionalized with integrin (RGD)- and heparin (KRSR)-binding peptides

Enhancing osseointegration through surface immobilization of multiple short peptide sequences that mimic extracellular matrix (ECM) proteins, such as arginine-glycine-aspartic acid (RGD) and lysine-arginine-serine-arginine (KRSR), has not yet been extensively explored. Additionally, the effect of biofunctionalizing chemically modified sandblasted and acid-etched surfaces (modSLA) is unknown. The present study evaluated modSLA implant surfaces modified with RGD and KRSR for potentially enhanced effects on bone apposition and interfacial shear strength during early stages of bone regeneration. Two sets of experimental implants were placed in the maxillae of eight miniature pigs, known for their rapid wound healing kinetics: bone chamber implants creating two circular bone defects for histomorphometric analysis on one side and standard thread configuration implants for removal torque testing on the other side. Three different biofunctionalized modSLA surfaces using poly-L-lysine-graft-poly(ethylene glycol) (PLL-g-PEG) as a carrier minimizing nonspecific protein adsorption [(i) 20 pmol cm?2 KRSR alone (KRSR); or in combination with RGD in two different concentrations; (ii) 0.05 pmol cm?2 RGD (KRSR/RGD-1); (iii) 1.26 pmol cm?2 RGD (KRSR/RGD-2)] were compared with (iv) control modSLA. Animals were sacrificed at 2 weeks. Removal torque values (701.48-780.28 N mm), bone-to-implant contact (BIC) (35.22%-41.49%), and new bone fill (28.58%-30.62%) demonstrated no significant differences among treatments. It may be concluded that biofunctionalizing modSLA surfaces with KRSR and RGD derivatives of PLL-g-PEG polymer does not increase BIC, bone fill, or interfacial shear strength.     

Histological and three-dimensional evaluation of osseointegration to nanostructured calcium phosphate-coated implants

Nanostructures on implant surfaces have been shown to enhance osseointegration; however, commonly used evaluation techniques are probably not sufficiently sensitive to fully determine the effects of this process. This study aimed to observe the osseointegration properties of nanostructured calcium phosphate (CaP)-coated implants, by using a combination of three-dimensional imaging and conventional histology. Titanium implants were coated with stable CaP nanoparticles using an immersion technique followed by heat treatment. Uncoated implants were used as the control. After topographical and chemical characterizations, implants were inserted into the rabbit femur. After 2 and 4weeks, the samples were retrieved for micro-computed tomography and histomorphometric evaluation. Scanning electron microscopy evaluation indicated that the implant surface was modified at the nanoscale by CaP to obtain surface textured with rod-shaped structures. Relative to the control, the bone-to-implant contact for the CaP-coated implant was significantly higher at 4weeks after the implant surgery. Further, corresponding 3-D images showed active bone formation surrounding the implant. 3-D quantification and 2-D histology demonstrated statistical correlation; moreover, 3-D quantification indicated a statistical decrease in bone density in the non-coated control implant group between 2 and 4weeks after the surgery. The application of 3-D evaluation further clarified the temporal characteristics and biological reaction of implants in bone.     

Improved bone ingrowth and fixation with a thin calcium phosphate coating intended for complete resorption

Bonit is claimed to be a resorbable electrochemically deposited calcium phosphate coating consisting mainly of brushite, which is a hydroxyapatite precursor. This study involved a comparison of Ti6Al4V screw-shaped implants with and without a 15 +/- 5 microm Bonit coating in rabbit tibia and femur, after 6 and 12 weeks of insertion. The biomechanical removal torque test showed significantly increased values for the coated implants after 12 weeks (p < 0.05) but not after 6 weeks of integration. Higher bone-implant contact was found for the coated implants in the tibia after 6 weeks and for both tibial and femoral screws after 12 weeks (p < 0.05). There was no difference in the inflammatory reaction around the implants, and possible grains of the coating could be detected after 6 weeks, but not after 12 weeks of follow-up. This unloaded short-term study has shown promising results for the easily applicable and resorbable coat (Bonit) compared to uncoated titanium-alloy implants.     

In vivo bone response and mechanical evaluation of electrosprayed CaP nanoparticle coatings using the iliac crest of goats as an implantation model

Recent trends in clinical implantology include the use of endosseous dental implant surfaces embellished with nano-sized modifications. The current study was initiated to evaluate the mechanical properties, as well as the potential beneficial effects, of electrosprayed CaP nanoparticle-coated (nano-CaP) implants on the in vivo osteogenic response, compared with grit-blasted, acid-etched (GAE) implant surfaces as controls. For this purpose nano-CaP coatings were deposited on cylindrical screw-type (St) implants and implanted bilaterally into the iliac crest of goats for 6 weeks. In addition to histological and histomorphometrical analyses, insertion torque and removal torque values were measured on implant placement and retrieval, respectively. The present study showed similar insertion and removal torque values for nano-CaP-coated and GAE control implants, with no statistically significant increase in torque value during the implant period for either group. With regard to bone–implant contact and peri-implant bone volume, no significant differences were found between nano-CaP-coated and GAE implants after 6 weeks implantation. In conclusion, this study has demonstrated that in situations in which implants are placed in a non-compromised situation using a standard press fit implantation strategy the performance of electrosprayed nano-CaP coatings is comparable with GAE implants, both with respect to implant fixation and bone healing response.