5-Fluorouracil-loaded microspheres prepared by spray-drying poly(D,L-lactide) and poly(lactide-co-glycolide) polymers: characterization and drug release

5-Fluorouracil (5-FU), a hydrosoluble anti-neoplastic drug, was encapsulated in microspheres of poly(D,L-lactide) (PLA) and poly(lactide-co-glycolide) (PLGA) polymers using the spray-drying technique, in order to obtain small size microspheres with a significant drug entrapment efficiency. Drug-loaded microspheres included between 47 +/- 11 and 67 +/- 12 microg 5-FU mg(-1) microspheres and the percentage of entrapment efficiency was between 52 +/- 12 and 74 +/- 13. Microspheres were of small size (average diameter: 0.9 +/- 0.4-1.4 +/- 0.8 microm microspheres without drug; 1.1 +/- 0.5-1.7 +/- 0.9 microm 5-FU-loaded microspheres) and their surface was smooth and slightly porous, some hollows or deformations were observed in microspheres prepared from polymers with larger Tg. A fractionation process of the raw polymer during the formation of microspheres was observed as an increase of the average molecular weight and also of Tg of the polymer of the microspheres. The presence of 5-FU did not modify the Tg values of the microspheres. Significant interactions between the drug and each one of the polymers did not take place and total release of the included drug was observed in all cases. The time needed for the total drug release (28-129 h) was in the order PLA > PLGA 75/25 > PLGA 50/50. A burst effect (17-20%) was observed during the first hour and then a period of constant release rate (3.52 +/- 0.82-1.46 +/- 0.26 microg 5-FU h(-1) per milligram of microspheres) up to 8 or 13 h, depending on the polymer, was obtained.     

Sustained release of ganciclovir from poly(lactide-co-glycolide) microspheres

Biodegradable poly(lactide-co-glycolide) microspheres loaded with ganciclovir were produced using the emulsification/solvent evaporation technique. The effects of drug-to-polymer ratio and dispersion time on the drug content in the microspheres were investigated. The release rate of the drug was studied for 20 weeks in a phosphate buffered solution of pH 7 at 37°C. Data revealed that lower drug content was obtained with increasing drug-to-polymer ratio and decreasing dispersion time. The release of the drug followed a triphasic release pattern, i.e. an initial burst, a diffusive phase and a second burst. The initial burst occurred within the first 2 days of immersion. After the burst, the release was by diffusion for up to 13 weeks, followed by another burst release, which signals the onset of bulk degradation of the polymer. Gel permeation chromatography (GPC), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and ultraviolet spectroscopy (UV) were used to follow the hydrolytic degradation and drug release rate of the microspheres.     

Characterization of Poly(glycolide-co-D,L-lactide)/Poly(D,L-lactide) Microspheres for Controlled Release of GM-CSF

Purpose. This study describes the preparation and characterization of a controlled release formulation of granulocyte-macrophage colony-stimulating factor (GM-CSF) encapsulated in poly(glycolide-co-D,L-lactide) (PLGA) and poly(D,L-lactide) (PLA) microspheres. Methods. GM-CSF was encapsulated in PLGA/PLA microspheres by a novel silicone oil based phase separation process. Several different blends of PLGA and low molecular weight PLA were used to prepare the microspheres. The microspheres and the encapsulated GM-CSF were extensively characterized both in vitroand in vivo. Results. Steady release of GM-CSF was achieved over a period of about one week without significant 'burst' of protein from the microspheres. Analysis of microsphere degradation kinetics by gel permeation chromatography (GPC) indicated that low molecular weight PLA enhanced the degradation of the PLGA and thereby affected release kinetics. GM-CSF released from the microspheres was found to be biologically active and physically intact by bioassay and chromato-graphic analysis. Analysis of serum from mice receiving huGM-CSF indicated that the GM-CSF was biologically active and that a concentration of greater than 10 ng/mL was maintained for a period lasting at least nine days. MuGM-CSF was not detected followingin vivo administration of muGM-CSF microspheres. The tissues of mice receiving muGM-CSF microspheres were characterized by infiltration of neutrophils, and macrophages which were in significant excess of those found in mice administered with placebo controls (i.e. microspheres without GM-CSF). Conclusions. This study demonstrates the influence of formulation parameters on the encapsulation of GM-CSF in PLGA/PLA microspheres and its controlled release in biologically active form. The intense local tissue reaction in mice to muGM-CSF microspheres demonstrates the importance of the mode of delivery on the pharmacologic activity of GM-CSF.     

布比卡因缓释微球的制备及体外释药特性评价

目的研究布比卡因缓释微球制备方法并对其体外释药特性进行评价。方法采用紫外分光光度法测定布比卡因微球载药量、包封率;采用HPLC法测定微球体外释放;通过正交设计优选微球制备工艺;以乳酸羟基乙酸共聚物为载体,使用乳化溶剂挥发法制备布比卡因微球;用扫描电镜观察所得微球的粒径和形态;通过体外释药实验考察布比卡因乳酸羟基乙酸共聚物微球的缓释作用。结果微球载药量、包封率和体外释放的测定方法符合方法学要求;按照优选处方制备所得的微球为圆整球体,表面多孔,呈蜂窝状,粒径50~100μm之间的微球占80%;体外释放符合Ritger-Peppas方程,t1/2=242.05 h。结论乳化溶剂挥发法适用于布比卡因乳酸羟基乙酸共聚物微球的制备,所制得的微球形态圆整,在体外具有明显缓释作用。     

Pentamidine-loaded poly(D,L-lactide) nanoparticles: Adsorption and drug release

This work describes the loading capacity of poly(D,L-lactide) nanoparticles, the factors influencing pentamidine release, and the cytotoxicity of nanoparticles. The nanoprecipitation method was used to prepare pentamidine-loaded poly(D,L-lactide) nanoparticles. Various concentrations of pentamidine base and polymer were tested. The influence of the dilution, temperature, and ionic strength was evaluated. The cytotoxicity on J 774 cells of unloaded nanoparticles, pentamidine-loaded nanoparticles, and pentamidine isethionate were tested. The percentage of binding decreased significantly with drug load. A nonlinear increase in drug uptake per unit mass of polymer with the equilibrium pentamidine concentration was found. A Langmuir-type sorption was suggested (r = 0.998). 390 μg/ml was found to be the highest level of drug incorporation. The increase of polymer concentration did not improve the pentamidine fixation yield. The increase in temperature or buffer molarity induced a significant release of pentamidine. The increase in dilution also induced an increase in release of pentamidine. The cytotoxicity of pentamidine-loaded nanoparticles and unloaded nanoparticles was superimposable. After 24 h of incubation, pentamidine-loaded nanoparticles presented an IC₅₀ value significantly lower than that of free drug (0.39 vs. 6.5 g/ml). Drug Dev. Res. 43:98–104, 1998. © 1998 Wiley-Liss, Inc.     

Degradation behaviour of microspheres prepared by spray-drying poly(D,L-lactide) and poly(D,L-lactide-co-glycolide) polymers

Polymeric microsphere degradation must be taken into account in the design of drug delivery systems to be injected in in vivo systems, thus a prior analysis of in vitro degradation behaviour of microspheres appears to be necessary. In this study degradation characteristics of poly(lactide-co-glycolide) (PLGA) and poly(D,L-lactide) (PLA) microspheres prepared by the spray-drying technique have been examined. It was found that a slow decrease in molecular weight took place during the first stage of degradation, and the value of the rate constant decreased with the increase of the percentage of lactic acid of the polymer in a linear way. Thus, the period of time of this first stage decreased with the increase of content of glycolidyl units of the polymer, and it was the unique stage observed in PLA microspheres after 5 months of study. During this period of time, significant mass loss was not observed in the microspheres. The second stage of degradation of PLGA microspheres showed a larger rate constant, whose value increased with the content of glycolidyl units of the polymer. Mass loss was observed from number-average molecular weight about 6000. A sharp decrease of glass transition temperature (T(g)) was observed coinciding with the start of mass loss. This fact was accompanied by a physical change of the samples, fusion of microspheres to form large particles, which also fusion to form a unique mass of polymer; moment from that the degradation process was quicker.     

Improvement of protein loading and modulation of protein release from poly(lactide-co-glycolide) microspheres by complexation of proteins with polyanions

A novel method was proposed to incorporate and modulate protein release from poly(lactide-co-glycolide) (PLGA) microspheres by a modified w/o/w emulsion solvent evaporation technique with poly(methacrylic acid) (PMAA)/insulin complex suspension as the inner aqueous phase instead of the neat protein solution. It was found that a reversible, water-insoluble complex could be formed between PMAA and insulin by electrostatic interactions. A great increase in insulin entrapment efficiency was observed as the PMAA/insulin complex was adopted to prepare PLGA microspheres. A large number of the complex particles adsorbed at the surface of the microspheres, resulting in the more rapid insulin release. The complexation and microencapsulation processes have little effect on insulin bioactivity, which was revealed by examination of the plasma glucose levels of the diabetic rats administrated with the microspheres.     

Ketotifen-loaded microspheres prepared by spray-drying poly(D,L-lactide) and poly(D,L-lactide-co-glycolide) polymers: characterization and in vivo evaluation

Ketotifen (KT) was encapsulated into poly(D,L-lactide) (PLA) and poly(D,L-lactide-co-glycolide) (PLGA 50/50) by spray-drying to investigate the use of biodegradable drug-loaded microspheres as delivery systems in the intraperitoneal cavity. Ketotifen stability was evaluated by HPLC, and degradation was not observed. Drug entrapment efficiency was 74 +/- 7% (82 +/- 8 microg KT/mg for PLA) and 81 +/- 6% (90 +/- 7 microg KT/mg for PLGA 50/50). PLA microspheres released ketotifen (57% of encapsulated KT) in 350 h at two release rates (221 microg/h, 15 min to 2 h; 1.13 microg/h, 5-350 h). A quicker release of ketotifen took place from PLGA 50/50 microspheres (67.4% of encapsulated KT) in 50 h (322 microg/h, 15 min to 2 h; 16.18 microg/h, 5-50 h). After intraperitoneal administration (10 mg KT/kg b.w.), microsphere aggregations were detected in adipose tissue. Ketotifen concentration was determined in plasma by HPLC. The drug released from PLA and PLGA 50/50 microspheres was detected at 384 and 336 h, respectively. Noncompartmental analysis was performed to determine pharmacokinetic parameters. The inclusion of ketotifen in PLGA and PLA microspheres resulted in significant changes in the plasma disposition of the drug. Overall, these ketotifen-loaded microspheres yielded an intraperitoneal drug release that may be suitable for use as delivery systems in the treatment of inflammatory response in portal hypertension.     

Stomach-specific drug delivery of 5-Fluorouracil using ethylcellulose floating microspheres

A multiple-unit-type oral floating dosage form (FDF) of 5-Fluorouracil (5-FU) was developed to prolong gastric residence time for the treatment of stomach cancer. The floating microspheres were prepared by solvent evaporation method. The prepared microspheres were characterized for their micromeretic properties, floating behavior and entrapment efficiency; as well by Fourier transform infrared spectroscopy (FTIR), Differential scanning calorimetry (DSC), X-ray powder diffractometry (XRPD), thin layer chromatography (TLC) and scanning electron microscopy (SEM). The in vitro release studies and floating behavior were performed in HCl buffer pH 1.2, Phosphate buffer pH 4.5 and in Simulated Gastric Fluid (SGF). The best fit release kinetics was achieved with Higuchi plot. The yields of preparation were very high and low entrapment efficiencies were noticed with larger particle size for all the formulations. Mean particle size, entrapment efficiency and production yield were highly influenced by polymer concentration. It was concluded from the present investigation that porous Ethylcellulose microspheres are promising controlled release as well as stomach targeted carriers for 5-FU.     

Effect of water on exenatide acylation in poly(lactide-co-glycolide) microspheres

Peptide or protein degradation often occurs when water flows into the dosage form. The aim of this study was to investigate the effect of water on exenatide acylation in poly(lactide-co-glycolide) (PLGA) microspheres. Exenatide-loaded PLGA microspheres were incubated at different relative humidities (RH) as well as in solutions of different pH for 20 days. The stability of exenatide was monitored using HPLC and HPLC–MS analysis. The alteration of exenatide conformation caused by water was investigated by FT-IR spectroscopy. Exenatide and glycolide were incubated in DMSO–water solutions to verify the effect of exenatide conformation state on the peptide acylation. Exenatide was relatively stable in microspheres at lower RH, and the absorbed water could act as a plasticizer and thus promote the peptide acylation by PLGA. However, when the microspheres were incubated at 100% RH, the excessively absorbed water could cause conformation recovery of exenatide and play an inhibitory effect on acylation. The formation of acylated exenatide incubated in acetate buffer saline of pH 6.0 was more than that of pH 4.5 and 3.0. Stability studies of exenatide in glycolide solutions showed that exenatide in nonnative monomer state was easier to be acylated by eletrophiles than that in aggregation state.     

超临界流体技术制备5-氟尿嘧啶聚乳酸微球

目的以5-氟尿嘧啶(5-Fu)为模型药物,制备氟尿嘧啶聚乳酸微球。方法采用超临界流体强制分散溶液技术,将5-Fu微粒化,并制备5-Fu聚乳酸微球。通过扫描电镜、激光粒度仪检测微球外形及粒径分布;气相色谱法测定二氯甲烷的残留量;恒温振荡透析法检测药物的释放度。结果25℃时,微粒化后5-Fu的乙醇饱和溶液浓度为6.43 mg.m l-1,较原料药的2.32 mg.m l-1有显著提高;所制备载药微球球形较好,表面光滑,粒径分布窄,粒径范围0.615~1.990μm,平均粒径为0.980μm;二氯甲烷残留量为0.0046%;微球载药量为2.6%,包封率为17.8%,药物释放呈缓释模式,无突释效应。结论超临界流体强制分散技术是制备5-Fu聚乳酸微球的可行方法。     

Preparation and Characterization of Poly (D,L-Lactide-Co-Glycolide) Microspheres for Controlled Release of Poly(L-Lysine) Complexed Plasmid DNA

Purpose. To produce and characterize controlled release formulations of plasmid DNA (pDNA) loaded in poly (D,L-lactide-co-glycolide) (PLGA) microspheres both in free form and as a complex with poly (L-lysine). Methods. Poly (L-lysine) (PLL) was used to form pDNA/PLL complexes with complexation ratio of 1:0.125 and 1:0.333 w/w to enhance the stability of pDNA during microsphere preparation and protect pDNA from nuclease attack. pDNA structure, particle size, zeta potential, drug loading, in vitro release properties, and protection from DNase I were studied. Results. The microspheres were found to be spherical with average particle size of 3.1-3.5 m. Drug loading of 0.6% was targeted. Incorporation efficiencies of 35.1% and 29.4-30.6% were obtained for pDNA and pDNA/PLL loaded microspheres respectively. Overall, pDNA release kinetics following the initial burst did not correlate with blank microsphere polymer degradation profile suggesting that pDNA release is convective diffusion controlled. The percentage of supercoiled pDNA in the pDNA and pDNA/PLL loaded microspheres was 16.6 % and 76.7-85.6% respectively. Unencapsulated pDNA and pDNA/PLL degraded completely within 30 minutes upon the addition of DNase I. Encapsulation of DNA/PLL in PLGA microspheres protected pDNA from enzymatic degradation. Conclusions. The results show that using a novel process, pDNA can be stabilized and encapsulated in PLGA microspheres to protect pDNA from enzymatic degradation.     

Water-soluble betamethasone-loaded poly(lactide-co-glycolide) hollow microparticles as a sustained release dosage form

In this study, betamethasone disodium phosphate-loaded microparticles were fabricated for sustained release using poly(lactide-co-glycolide) (PLGA) by spray drying and emulsion solvent evaporation/extraction techniques. Encapsulation efficiencies ranged from 59–80% using a water-in-oil-in-oil (W/O/O) double emulsion technique and more than 90% for a spray-drying method were obtained. This was a significant improvement compared to fabrication by a water-in-oil-in-water (W/O/W) double emulsion process, which had an encapsulation efficiency of less than 15%. Multiple-phase and biphasic release profiles were observed for microparticles of PLGA 50/50 and PLGA of higher lactide contents, respectively. The PLGA 50/50 hollow microparticles fabricated using the W/O/O double emulsion technique provided a sustained release of betamethasone disodium phosphate over 3 weeks.     

Biodegradable poly(D,L-lactide-co-glycolide) (PLGA) microspheres for sustained release of risperidone: Zero-order release formulation

The preparation and investigation of sustained-release risperidone-encapsulated microspheres using erodible poly(D, L-lactide-co-glycolide) (PLGA) of lower molecular weight were performed and compared to that of commercial Risperdal Consta^? for the treatment of schizophrenia. The research included screening and optimizing of suitable commercial polymers of lower molecular weight PLGA50/50 or the blends of these PLGA polymers to prepare microspheres with zero-order release kinetics properties. Solvent evaporation method was applied here while studies of the risperidone loaded microsphere were carried out on its drug encapsulation capacity, morphology, particle size, as well as in vitro release profiles. Results showed that microspheres prepared using 50504A PLGA or blends of 5050-type PLGAs exerted spherical and smooth morphology, with a higher encapsulation efficiency and nearly zero-order release kinetics. These optimized microspheres showed great potential for a better depot preparation than the marketed Risperdal Consta^?, which could further improve the patient compliance.     

影响聚酯微球中药物释放的因素

聚酯材料因其原料易得、容易加工、生物相容性好、具有可生物降解性等优点,已经成为当今药物载体材料中的一大研究热点。现综合国内外的有关报道对可生物降解聚酯材料作为药物载体制备微球制剂的研究进展进行了综述。针对目前限制聚酯材料微球制剂临床应用存在的问题,从聚合物、药物、制备工艺、附加剂、辐射灭菌5个方面对影响聚乳酸(PLA)和聚乳酸乙醇酸共聚物(PLGA)缓释微球中药物释放的因素进行了重点介绍,为研究聚酯微球中药物的释放提供思路。     

5-Fluorouracil plasma levels and biodegradation of subcutaneously injected drug-loaded microspheres prepared by spray-drying poly(D,L-lactide) and poly(D,L-lactide-co-glycolide) polymers

Microspheres (MS) of 5-fluorouracil-loaded poly(D,L-lactide) (PLA), poly(D,L-lactide-co-glycolide) 75/25 (PLGA 75/25) and poly(D,L-lactide-co-glycolide) 50/50 (PLGA 50/50) prepared by the spray-drying technique were subcutaneously injected in the back of Wistar rats in order to evaluate the 5-fluorouracil (5-FU) release and the biodegradation characteristics. Determination of plasma 5-FU concentration by HPLC with analysis of data using a non-compartmental model showed drug in plasma between 9 and 14 days after administration of drug-loaded PLGA 50/50 or PLA and PLGA 75/25 microspheres, respectively, with a maximum drug concentration of 2.4+/-0.2microg/mL at 24h (5-FU-loaded PLGA 50/50 MS), 2.5+/-0.1microg/mL at 48h (5-FU-loaded PLGA 75/25 MS), and 2.3+/-0.1microg/mL at 24h (5-FU-loaded PLA MS). Pharmacokinetically, a significant increase of AUC (up to 50 times) and MRT (up to 196 times) of 5-FU with regard to the administration of the drug in solution was observed. Scanning electron microscopy and histological studies indicated that a small fibrous capsule was observed around the microspheres in the site of injection. One month after the injection of PLGA 50/50 MS and 2 months after the injection of PLGA 75/25 and PLA MS, masses of polymers, instead of single microspheres, were observed. Close to them, macrophagic cells were present, and blood vessels were observed in the connective tissue. Total absence of fibrous capsule and injected microspheres was observed after 2 (for PLGA 50/50 MS) or 3 (PLGA 75/25 and PLA MS) months.     

替硝唑聚乳酸微球的制备及其体外释药性能

目的：采用聚乳酸[poly（DL-lactide）]制备替硝唑微球。方法：考察分散递质明胶溶液的浓度、油相中聚乳酸的浓度、投药比和搅拌速度等因素的影响，应用正交实验优选最佳制备工艺条件。结果：替硝唑聚乳酸微球的最佳制备工艺稳定、重复性好，微球表面圆整，粒径分布均匀，微球平均粒径为30．2μm，平均载药量为6．7％，平均包封率为64．5％。该微球在14d的药物累积释放率达81．2％。结论：替硝唑聚乳酸微球缓释时间长达14d，用于牙周炎的治疗是有效的。     

Reduction in burst release after coating poly(D,L-lactide-co-glycolide) (PLGA) microparticles with a drug-free PLGA layer

The high initial burst release of a highly water-soluble drug from poly (D,L-lactide-co-glycolide) (PLGA) microparticles prepared by the multiple emulsion (w/o/w) solvent extraction/evaporation method was reduced by coating with an additional polymeric PLGA layer. Coating with high encapsulation efficiency was performed by dispersing the core microparticles in peanut oil and subsequently in an organic polymer solution, followed by emulsification in the aqueous solution. Hardening of an additional polymeric layer occurred by oil/solvent extraction. Peanut oil was used to cover the surface of core microparticles and, therefore, reduced or prevented the rapid erosion of core microparticles surface. A low initial burst was obtained, accompanied by high encapsulation efficiency and continuous sustained release over several weeks. Reduction in burst release after coating was independent of the amount of oil. Either freshly prepared (wet) or dried (dry) core microparticles were used. A significant initial burst was reduced when ethyl acetate was used as a solvent instead of methylene chloride for polymer coating. Multiparticle encapsulation within the polymeric layer increased as the size of the core microparticles decreased (< 50 µm), resulting in lowest the initial burst. The initial burst could be controlled well by the coating level, which could be varied by varying the amount of polymer solution, used for coating.     

Stabilization and Controlled Release of Bovine Serum Albumin Encapsulated in Poly(D,L-lactide) and Poly(ethylene glycol) Microsphere Blends

Purpose. The acidic microclimate in poly(D, L-lactide-co-glycolide) 50/50 microspheres has been previously demonstrated by our group as the primary instability source of encapsulated bovine serum albumin (BSA). The objectives of this study were to stabilize the encapsulated model protein, BSA, and to achieve continuous protein release by using a blend of: slowly degrading poly(D, L-lactide) (PLA), to reduce the production of acidic species during BSA release; and pore-forming poly(ethylene glycol) (PEG), to increase diffusion of BSA and polymer degradation products out of the polymer. Methods. Microspheres were formulated from blends of PLA (Mw 145,000) and PEG (Mw 10,000 or 35,000) by using an anhydrous oil-in-oil emulsion and solvent extraction (O/O) method. The polymer blend composition and phase miscibility were examined by FT-IR and DSC, respectively. Microsphere surface morphology, water uptake, and BSA release kinetics were also investigated. The stability of BSA encapsulated in microspheres was examined by losses in protein solubility, SDS-PAGE, IEF, CD, and fluorescence spectroscopy. Results. PEG was successfully incorporated in PLA microspheres and shown to possess partial miscibility with PLA. A protein loading level of 5% (w/w) was attained in PLA/PEG microspheres with a mean diameter of approximately 100 m. When PEG content was less than 20% in the blend, incomplete release of BSA was observed with the formation of insoluble, and primarily non-covalent aggregates. When 20%-30% PEG was incorporated in the blend formulation, in vitro continuous protein release over 29 days was exhibited. Unreleased BSA in these formulations was water-soluble and structurally intact. Conclusions. Stabilization and controlled relaease of BSA from PLA/PEG microspheres was achieved due to low acid and high water content in the blend formulation.     

2-脱氧葡萄糖聚乳酸微球的制备及其体外释药性能的研究

目的采用W/O/O乳化溶剂挥发法制备2-脱氧葡萄糖聚乳酸微球(2-Deoxyglucoseloadedpoly(DL-lactide)microspheres,2DG-PLA-MS),并研究其体外释药性能。方法考察3个因素(即投药比、水丙酮体积比和丙酮液体石蜡体积比)对微球的粒径、载药量和包封率的影响,应用正交实验优选最佳制备工艺条件。结果2DG-PLA-MS的制备工艺稳定,重复性好,微球表面圆整,粒径分布均匀,微球平均粒径45μm,平均载药量为42.41%,平均包封率为72.63%。该微球在14d的药物累积释放率达82.96%。结论2DG-PLA-MS具有明显的缓慢释放作用,能够实现延长药物作用时间、减少给药次数、降低药用剂量和减少不良反应等作用。