Biomechanical and histomorphometric analysis of etched and non-etched resorbable blasting media processed implant surfaces: An experimental study in dogs

This study characterized the interplay between topography/chemistry and early bone response of etched and no-etched resorbable blasted media (RBM) processed surfaces. Screw-root form Ti–6Al–4V implants treated with alumina blasting/acid-etching (AB/AE), RBM alone (RBM), and RBM + acid-etching (RBMa) were evaluated. The surface was characterized by scanning electron microscopy, atomic force microscopy, and X-ray photoelectron spectroscopy. Implants placed in the tibia of dogs remained 3 and 5 weeks in vivo. Following euthanasia, half of the specimens were torqued to interface failure and the remaining subjected to bone-to-implant contact (BIC) and bone area fraction occupied (BAFO) between threads evaluation. The AB/AE surface was rougher than the RBM and RBMa. Higher levels of calcium and phosphorous were observed for the RBM surface compared to the RBMa. No significant differences were observed in torque, BIC, and BAFO between surfaces. Woven bone formation at 3 weeks and its initial replacement by lamellar bone at 5 weeks were observed around all implants’ surfaces.     

Biological performance of biomimetic calcium phosphate coating of titanium implants in the dog mandible

The aim of the present study was to analyze the in vivo effect of biomimetic calcium phosphate coating of titanium implants on periimplant bone formation and bone-/implant contact. Five types of implants were used: 1) Ti6Al4V implants with a polished surface; 2) Ti6Al4V implants with collagen coating; 3) Ti6Al4V implants with a mineralized collagen layer; 4) Ti6Al4V implants with sequential coating of hydroxyapatite (HA) and collagen; and 5) Ti6Al4V implants with HA coating only. All implants had square cross sections with an oblique diameter of 4.6 mm and were inserted press fit into trephine burr holes of 4.6 mm in the mandibles of ten beagle dogs. The implants of five animals each were evaluated after a healing period of 1 month and 3 months, respectively, during which time sequential fluorochrome labeling of bone formation had been performed. Bone formation was evaluated by morphometric measurement of the newly formed bone around the implants and the percentage of implant bone contact. After 1 month, there was a significantly higher percentage of mean bone/implant contact in the HA-coated implants compared to those with polished surface and those with the collagen-coated surface. After 3 months, these differences were not present anymore. Bone apposition was significantly higher next to implants with sequential HA/collagen coating compared to polished surfaces and mineralized collagen layer. It is concluded that biomimetic coating of titanium implants with HA has shown the clearest trend to increase bone-implant contact in the early ingrowth period. The addition of collagen to an HA coating layer may hold some promise when used as sequential HA/collagen coating with mineralized collagen as the surface layer.     

Bioactive glass microspheres as osteopromotive inlays in macrotextured surfaces of Ti and CoCr alloy bone implants: trapezoidal surface grooves without inlay most efficient in resisting torsional forces

We have tested the efficacy of porous bioactive glass (BG) inlays in enhancement of implant osseointegration. A total of 24 sheep underwent bilateral surgical implantation of three parallel implants on the anteromedial cortical surface of each tibia. The disc-shaped implants made of Ti6Al4V or cobalt chromium (CoCr) alloys had two parallel surface grooves (trapezoidal space with bottom widening) filled with sintered 100% bioactive glass microspheres or a selected mixture of bioactive and biocompatible glass microspheres. The surface of uncoated control implants was smooth, grit-blasted or had unfilled grooves. A subgroup of control smooth CoCr implants was coated with two or three BG layers. Implant incorporation with bone was evaluated using torque testing to failure, scanning electron microscopy and morphometry at 12 and 25 weeks. A total of 144 in vivo implants and 16 ex vivo cemented control implants were analyzed. Control Ti6Al4V implants with unfilled trapezoidal grooves showed highest torsional failure loads with excellent ingrowth of new bone and remodeling of ingrown bone into lamellar bone. Implants with BG inlays and microroughened control Ti6Al4V implants showed significantly lower torsional failure loads than control Ti6Al4V implants with unfilled grooves. In conclusion, BG inlays failed to enhance biological implant fixation. Macrotextured surface was more effective than grit-blasting in promotion of mechanical incorporation.     

Functionalization of dental implant surfaces using adhesion molecules

The aim of the present study was to test the hypothesis that organic coating of titanium screw implants that provides binding sites for integrin receptors can enhance periimplant bone formation. Ten adult female foxhounds received experimental titanium screw implants in the mandible 3 months after removal of all premolar teeth. Four types of implants were evaluated in each animal: (1) implants with machined titanium surface, (2) implants coated with collagen I, (3) implants with collagen I and cyclic RGD peptide coating (Arg-Gly-Asp) with low RGD concentrations (100 micromol/mL), and (4) implants with collagen I and RGD coating with high RGD concentrations (1000 micromol/mL). Periimplant bone regeneration was assessed histomorphometrically after 1 and 3 months in five dogs each by measuring bone implant contact (BIC) and the volume density of the newly formed periimplant bone (BVD). After 1 month, BIC was significantly enhanced only in the group of implants coated with the higher concentration of RGD peptides (p = 0.026). Volume density of the newly formed periimplant bone was significantly higher in all implants with organic coating. No significant difference was found between collagen coating and RGD coatings. After 3 months, BIC was significantly higher in all implants with organic coating than in implants with machined surfaces. Periimplant BVD was significantly increased in all coated implants in comparison to machined surfaces also. It was concluded that organic coating of machined screw implant surfaces providing binding sites for integrin receptors can enhance bone implant contact and periimplant bone formation.     

Osteointegration of biomimetic apatite coating applied onto dense and porous metal implants in femurs of goats

Biomimetic calcium phosphate (Ca-P) coatings were applied onto dense titanium alloy (Ti6Al4V) and porous tantalum (Ta) cylinders by immersion into simulated body fluid at 37 degrees C and then at 50 degrees C for 24 h. As a result, a homogeneous bone-like carbonated apatitic (BCA) coating, 30 microm thick was deposited on the entire surface of the dense and porous implants. Noncoated and BCA-coated implants were press-fit implanted in the femoral diaphysis of 14 adult female goats. Bone contact was measured after implantation for 6, 12, and 24 weeks, and investigated by histology and backscattered electron microscopy (BSEM). After 6 weeks, bone contact of the BCA-coated Ti6Al4V implants was about 50%. After 12 and 24 weeks, bone contact was lower in comparison with the 6-week implantations at, respectively 24 and 39%. Regarding the BCA-coated porous Ta implants, bone contacts were 17, 30, and 18% after 6, 12, and 24 weeks, respectively. However, bone contact was always found significantly higher for BCA-coated dense Ti6Al4V and porous Ta cylinders than the corresponding noncoated implants. The results of this study show that the BCA coating enhances the bone integration as compared to the noncoated implants.     

In vivo evaluation of bone-bonding ability of RGD-coated porous implant using layer-by-layer electrostatic self-assembly

RGD has been demonstrated to improve implant osseointegration. However, few studies are known about an effect of RGD coating on a bone-bonding ability of screw-shaped porous implant. The aim of this study was to investigate the effect of RGD coating using the layer-by-layer self-assembly technique on the bone-bonding ability of porous implant. 60 implants of 10 mm in length (30 control and 30 RGD-coated) were inserted into femurs of 30 rabbits and 30 implants of 8 mm in length (15 control and 15 RGD-coated) were inserted into tibias of 15 rabbits. At 4, 8, and 12 weeks post-implantation, femurs and tibias were retrieved and prepared for removal torque tests (RTQ) and histomorphometric evaluation, respectively. No differences were found in the RTQ values between two implants at 4 weeks (p = 0.932). There were statistical significances in the RTQ values at 8 and 12 weeks (p = 0.002, 0.001, respectively). New bone was formed on both implant surfaces. The bone-implant contact pattern appeared to produce a broad-based direct contact in both implants. The RGD-coated implants showed a significantly greater BIC in the threads inside the cortical bone compared with the control implants at 4, 8, and 12 weeks (p = 0.024, 0.041, 0.022, respectively). No differences were found in the bone area within the same threads between two implants at 4 weeks (p = 0.806) whereas differences were found at 8 and 12 weeks (p = 0.009, 0.031, respectively). It was concluded that RGD coating using the layer-by-layer self-assembly technique has a positive effect on the bone-bonding ability of porous implant.     

Influence of a zirconia sandblasting treated surface on peri-implant bone healing: An experimental study in sheep

A sandblasting process with round zirconia (ZrO₂) particles might be an alternative surface treatment to enhance the osseointegration of titanium dental implants. Our previous study on sheep compared smooth surface titanium implants (control) with implant surfaces sandblasted with two different granulations of ZrO₂. As the sandblasted surfaces proved superior, the present study further compared the ZrO₂ surface implant with other surface treatments currently employed: machined titanium (control), titanium oxide plasma sprayed (TPS) and alumina sandblasted (Al-SL) at different times after insertion (2, 4 and 12 weeks). Twelve sheep were divided into three groups of four animals each and underwent implant insertion in tibia cortical bone under general anaesthesia. The implants with surrounding tissues were subjected to histology, histomorphometry, scanning electron microscopy and microhardness tests. The experimentation indicated that at 2 weeks Zr-SL implants had the highest significant bone ingrowth (p < 0.05) compared to the other implant surfaces, and a microhardness of newly formed bone inside the threads significantly higher than that of Ti. The present work shows that the ZrO₂ treatment produces better results in peri-implant newly formed bone than Ti and TPS processing, whereas its performance is similar to the Al-SL surface treatment.     

Osteoblast response and osseointegration of a Ti–6Al–4V alloy implant incorporating strontium

This study investigated the surface characteristics, in vitro and in vivo biocompatibility of Ti–6Al–4V alloy implants incorporating strontium ions (Sr), produced by hydrothermal treatment using a Sr-containing solution, for future biomedical applications. The surface characteristics were evaluated by scanning electron microscopy, thin-film X-ray diffractometry, X-ray photoelectron spectroscopy, optical profilometry, contact angle and surface energy measurement and inductively coupled plasma-mass spectroscopy (ICP-MS). Human osteoblast-like cell (MG63) attachment, proliferation, alkaline phosphatase (ALP) activity, and quantitative analysis of osteoblastic gene expression on Sr-containing Ti–6Al–4V surfaces were compared with untreated Ti–6Al–4V surfaces. Fifty-six screw implants (28 control and 28 experimental) were placed in the tibiae and femoral condyles of seven New Zealand White rabbits. The osteoconductivity of Sr-containing Ti–6Al–4V implants was evaluated by removal torque testing and histomorphometric analysis after 4 weeks implantation. Hydrothermal treatment produced a crystalline SrTiO₃ layer. ICP-MS analysis showed that Sr ions were released from treated surfaces into the solution. Significant increases in ALP activity (P = 0.000), mRNA expressions of key osteoblast genes (osterix, bone sialoprotein, and osteocalcin), removal torque values (P < 0.05) and bone–implant contact percentages (P < 0.05) in both cortical and cancellous bone were observed for Sr-containing Ti–6Al–4V surfaces. The results indicate that the Sr-containing oxide layer produced by hydrothermal treatment may be effective in improving the osseointegration of Ti–6Al–4V alloy implants by enhancing differentiation of osteoblastic cells, removal torque forces and bone apposition in both cortical and cancellous bone.     

Bone healing of commercial oral implants with RGD immobilization through electrodeposited poly(ethylene glycol) in rabbit cancellous bone

Immobilization of RGD peptides on titanium (Ti) surfaces enhances implant bone healing by promoting early osteoblastic cell attachment and subsequent differentiation by facilitating integrin binding. Our previous studies have demonstrated the efficacy of RGD peptide immobilization on Ti surfaces through the electrodeposition of poly(ethylene glycol) (PEG) (RGD/PEG/Ti), which exhibited good chemical stability and bonding. The RGD/PEG/Ti surface promoted differentiation and mineralization of pre-osteoblasts. This study investigated the in vivo bone healing capacity of the RGD/PEG/Ti surface for biomedical application as a more osteoconductive implant surface in dentistry. The RGD/PEG/Ti surface was produced on an osteoconductive implant surface, i.e. the grit blasted micro-rough surface of a commercial oral implant. The osteoconductivity of the RGD/PEG/Ti surface was compared by histomorphometric evaluation with an RGD peptide-coated surface obtained by simple adsorption in rabbit cancellous bone after 2 and 4 weeks healing. The RGD/PEG/Ti implants displayed a high degree of direct bone apposition in cancellous bone and achieved greater active bone apposition, even in areas of poor surrounding bone. Significant increases in the bone to implant contact percentage were observed for RGD/PEG/Ti implants compared with RGD-coated Ti implants obtained by simple adsorption both after 2 and 4 weeks healing (P<0.05). These results demonstrate that RGD peptide immobilization on a Ti surface through electrodeposited PEG may be an effective method for enhancing bone healing with commercial micro-rough surface oral implants in cancellous bone by achieving rapid bone apposition on the implant surface.     

Qualitative and quantitative observations of bone tissue reactions to anodised implants

Research projects focusing on biomaterials related factors; the bulk implant material, the macro-design of the implant and the microsurface roughness are routinely being conducted at our laboratories. In this study, we have investigated the bone tissue reactions to turned commercially pure (c.p.) titanium implants with various thicknesses of the oxide films after 6 weeks of insertion in rabbit bone. The control c.p. titanium implants had an oxide thickness of 17-200 nm while the test implants revealed an oxide thickness between 600 and 1000 nm. Routine histological investigations of the tissue reactions around the implants and enzyme histochemical detections of alkaline and acid phosphatase activities demonstrated similar findings around both the control and test implants. In general, the histomorphometrical parameters (bone to implant contact and newly formed bone) revealed significant quantitative differences between the control and test implants. The test implants demonstrated a greater bone response histomorphometrically than control implants and the osteoconductivity was more pronounced around the test implant surfaces. The parameters that differed between the implant surfaces, i.e. the oxide thickness, the pore size distribution, the porosity and the crystallinity of the surface oxides may represent factors that have an influence on the histomorphometrical results indicated by a stronger bone tissue response to the test implant surfaces, with an oxide thickness of more than 600 nm.     

Bone growth in rapid prototyped porous titanium implants

Two porous titanium implants with a pore size diameter of 800 and 1200 microm (Ti800 and Ti1200) and an interconnected network were manufactured using rapid prototyping. Their dimensions and structure matched those of the computer assisted design. The porosity of the implants was around 60%. Their compressive strength and Young's modulus were around 80 MPa and 2.7 GPa, respectively. These values are comparable to those of cortical bone. The implants were implanted bilaterally in the femoral epiphysis of 15 New Zealand White rabbits. After 3 and 8 weeks, abundant bone formation was found inside the rapid prototyped porous titanium implants. For the Ti1200 implants, bone ingrowth was (23.9 +/- 3.5)% and (10.3 +/- 2.8)%, respectively. A significant statistical difference (p < 0.05) was found for bone ingrowth in the Ti1200 between the two delays. The percentage of bone directly apposited on titanium was (35.8 +/- 5.4)% and (30.5 +/- 5.0)%. No significant difference was found for bone-implant contact between the different time periods and pore sizes. This work demonstrates that manufacturing macroporous titanium implants with controlled shape and porosity using a rapid prototyping method is possible and that this technique is a good candidate for orthopedic and maxillofacial applications.     

Effects of calcium ion incorporation on bone healing of Ti6Al4V alloy implants in rabbit tibiae

The biocompatibility of calcium ion (Ca)-incorporated Ti6Al4V alloy implants, produced by hydrothermal treatment using a Ca-containing solution, was investigated. The surface characteristics were evaluated by scanning electron microscopy, thin-film X-ray diffractometry, Auger electron spectroscopy, and stylus profilometry. The viability of MC3T3-E1 cells on Ca-incorporated machined Ti6Al4V surfaces with different oxide thicknesses was compared with that on untreated machined Ti6Al4V surfaces with MTT assay. The osteoconductivity of the Ca-incorporated Ti6Al4V implants was evaluated by removal torque testing and histomorphometric analysis after 6 weeks of implantation in rabbit tibiae. Our results show that hydrothermal treatment with a Ca-containing solution produced a crystalline CaTiO(3) layer on Ti6Al4V surfaces, and calcium ions were gradually incorporated throughout the oxide layer. After immersion in Hank's balanced salt solution, a considerable apatite deposition was observed on all surfaces of the Ca-incorporated samples. Significant increases in cell viability (p<0.001), removal torque forces, and bone-to-implant contact values (p<0.05) were observed for Ca-incorporated Ti6Al4V implants compared with those for untreated Ti6Al4V implants.     

In vivo histological response to anodized and anodized/hydrothermally treated titanium implants

In the study, characterization of the anodized titanium surface was performed. In addition, histological evaluation and interfacial strength at the bone-implant interface of the characterized surfaces were then evaluated with the use of a rabbit model at 6 and 12 weeks after implantation. Surface treatments consisted of either anodization or anodization followed by hydrothermal treatments. Nontreated titanium surfaces were used as controls in this study. Using scanning-electron microscopy, porous oxide layers were observed on surfaces of anodized titanium implants, whereas porous oxide layers and HA needles were observed on anodized titanium implants following hydrothermal treatments. X-ray diffraction analysis showed the oxide layers were consisted mainly of anatase and a little of rutile. By the hydrothermal treatment on the anodizing surface, HA peaks, as well as the peaks of anatase and trace amounts of rutile peaks were observed. In EPMA analysis, the Ca/P ratio for the anodic oxide was 1.54 for anodized surfaces, whereas the Ca/P ratios for HA needles and the anodic oxide were 1.64 and 0.57, respectively, for anodized surfaces following hydrothermal treatments. Although no significant difference was observed for the percent bone contact on all implants evaluated in the in vivo study, the removal torque strength was significantly higher for anodized implants (48.02+/-5.92 N/cm) than the untreated implants (controls) (27.83+/-1.78 N/cm) at 6 weeks after implantation. As such, it was concluded that the surface anodized implants resulted in a high interfacial strength at an early implantation period as compared to the nontreated titanium implants.     

Evaluation of titanium plasma-sprayed and plasma-sprayed hydroxyapatite implants in vivo

In this study, bone interfacial strength and bone contact length at the plasma-sprayed hydroxyapatite (HA) and titanium plasma-sprayed (TPS) implants were evaluated in vivo. Non-coated titanium (Ti) implants were used as controls. Cylindrical coated or non-coated implants (4.0mm diameter by 8mm long) were implanted in the dogs' mandibles. Loading of the implants was performed at 12 weeks after implantation. At 12 weeks after implantation (prior to loading) and 1 year after loading, implants were evaluated for interfacial bone-implant strength and bone-implant contact length. No significant differences in interfacial bone-implant strength for all groups at 12 weeks after implantation and after 1 year loading in normal bone were found. However, bone contact length for HA implants was significantly higher than the TPS and Ti implants for both periods tested (12 weeks after implantation and 1 year after loading). It was concluded that TPS implants exhibited similar pull-out strength compared to the HA implants. In addition, the lower bone contact length on the TPS surface compared to HA surfaces did not affect the interfacial bone-implant strength for both implants.     

Early detachment of titanium particles from various different surfaces of endosseous dental implants

Titanium (Ti) endosseous dental screws with different surfaces (smooth titanium--STi, titanium plasma-sprayed-TPS, alumina oxide sandblasted and acid-etched--Al-SLA, zirconium oxide sandblasted and acid etched--Zr-SLA) were implanted in femura and tibiae of sheep to investigate the biological evolution of the peri-implant tissues and detachment of Ti debris from the implant surfaces in early healing. Implants were not loaded. Sections of the screws and the peri-implant tissues obtained by sawing and grinding were analysed by light microscopy immediately after implantation (time 0) and after 14 days. All samples showed new bone trabeculae and vascularised medullary spaces in those areas where gaps between the implants and host bone were visible. In contrast, no osteogenesis was induced in the areas where the implants were initially positioned in close contact with the host bone. Chips of the pre-existing bone inducing new peri-implant neo-osteogenesis were surrounded by new bone trabeculae. The threads of some screws appeared to be deformed where the host bone showed fractures. Ti granules of 3-60 microm were detectable only in the peri-implant tissues of TPS implants both immediately after surgery and after 14 days, thus suggesting that this phenomenon may be related to the friction of the TPS coating during surgical insertion.     

A novel multiphase anodic spark deposition coating for the improvement of orthopedic implant osseointegration: an experimental study in cortical bone of sheep

The effect of a new three-step anodic spark deposition process, labeled TiSpark, including two consecutive treatments performed first in a P solution and second in Ca solution, followed by an additional alkali etching step, was investigated for the improvement of osseointegration of commercial grade 2 titanium, machined (Ti) or Al(2)O(3) sandblasted (Ti-SA), cylindrical implants (12 mm in length and 4 mm in diameter) in cortical bone of 12 adult sheep. Histomorphometric and microhardness measurements were carried out at each experimental time (4, 8, and 12 weeks) to quantify the bone-to-implant contact around the implants as well as the newly bone hardness and bone maturation index. TiSpark treated surfaces were covered by a thick layer of crystalline anatase TiO(2) and by a further Ca/P layer. Bone tissue extends and grows on the surface of the TiSpark treated implants without any fibrous tissue, enhancing the short-term osseointegration properties of implant. Bone mineralization rate was also influenced by the chemical composition of implants and sandblasted materials presented the lowest bone maturation rate at the interface. Data suggests that the TiSpark treatment produces a modification of the Ti surface, which presents good bioactivity and may be suitable for achieving a stable implant osseointegration.     

The effect of plasma chemical oxidation of titanium alloy on bone-implant contact in rats

Many different technologies have been used to enhance osseointegration in orthopaedic and dental implant surgery. Hydroxyapatite coatings, pure or in combination with growth factors or bisphosphonates, showed improved osseointegration of titanium alloy implants. We choose a different approach to enhance osseointegration: plasma chemical oxidation was used to modify the surface of titanium alloy implants. This technique converts the nm-thin natural occurring titanium oxide layer on an implant to a 4?μm thick ceramic coating (TiOB surface). Bioactive TiOB surfaces have a macroporous structure and were loaded with calcium and phosphorus, while bioinert TiOB surfaces are smooth. A rat tibial model with bilateral placement of titanium alloy implants was employed to analyze the bone response to TiOB surfaces in?vivo. 64 rats were randomly assigned to four groups of implants: (1) titanium alloy (control), (2) titanium alloy, type III anodization, (3) bioinert TiOB surface and (4) bioactive TiOB surface. Mechanical fixation, peri-implant-bone area and bone contact were evaluated by pull-out tests and histology at three and eight weeks. Shear strength and bone contact at eight weeks were significantly increased in the bioactive TiOB group compared to all other groups. The results of plasma chemical oxidation in a rat model showed that the bioactive TiOB surface has a positive effect on implant anchorage by enhancing the bone-implant contact in normal bone.     

Bone tissue, cellular, and molecular responses to titanium implants treated by anodic spark deposition

A myriad of titanium (Ti) surface modifications has been proposed to hasten the osseointegration. In this context, the aim of this study was to perform histomorphometric, cellular, and molecular analyses of the bone tissue grown in close contact with Ti implants treated by anodic spark deposition (ASD-AK). Acid-etched (AE) Ti implants either untreated or submitted to ASD-AK were placed into dog mandibles and retrieved at 3 and 8 weeks. It was noticed that both implants, AE and ASD-AK, were osseointegrated at 3 and 8 weeks. Histomorphometric analysis showed differences between treatments only for bone-to-implant contact, being higher on AE implants. Although not backed by histomorphometric results, gene expression of key bone markers was higher for bone grown in close contact with ASD-AK and for cells harvested from these fragments and cultured until subconfluence. Cell proliferation at days 7 and 10 and alkaline phosphatase activity at day 10 was higher on AE surfaces. No statistical significant difference was noticed for extracellular matrix mineralization at 17 days. Our results have shown that the Ti fixtures treated by ASD-AK allowed in vivo osseointegration and induced higher expression of key markers of osteoblast phenotype, suggesting that this surface treatment could be considered to produce implants for clinical applications. ? 2012 Wiley Periodicals, Inc. J Biomed Mater Res Part A: 100A:3092-3098, 2012.     

Rapid prototyped porous titanium coated with calcium phosphate as a scaffold for bone tissue engineering

High strength porous scaffolds and mesenchymal stem cells are required for bone tissue engineering applications. Porous titanium scaffolds (TiS) with a regular array of interconnected pores of 1000 microm in diameter and a porosity of 50% were produced using a rapid prototyping technique. A calcium phosphate (CaP) coating was applied to these titanium (Ti) scaffolds with an electrodeposition method. Raman spectroscopy and energy dispersive X-ray analysis showed that the coating consisted of carbonated hydroxyapatite. Cross-sectioned observations by scanning electron microscopy indicated that the coating evenly covered the entire structure with a thickness of approximately 25 microm. The bonding strength of the coating to the substrate was evaluated to be around 25 MPa. Rat bone marrow cells (RBMC) were seeded and cultured on the Ti scaffolds with or without coating. The Alamar Blue assay provided a low initial cell attachment (40%) and cell numbers were similar on both the uncoated and coated Ti scaffolds after 3 days. The Ti scaffolds were subsequently implanted subcutaneously for 4 weeks in syngenic rats. Histology revealed the presence of a mineralized collagen tissue in contact with the implants, but no bone formation. This study demonstrated that porous Ti scaffolds with high strength and defined geometry may be evenly coated with CaP layers and cultured mesenchymal stem cells for bone tissue engineering.     

Cellular reactions and bone apposition to titanium surfaces with different surface roughness and oxide thickness cleaned by oxidation

Titanium surfaces with three different surface characteristics were exposed to an intraperitoneal milieu in mouse or rat, or inserted into rabbit bone. The cleaning regimen of the TiO2 surfaces in this study included oxidation by heat or acid and a final rinsing and storage in water. Intraperitoneal exposure ranged from 1 to 64 min and the healing period in bone was 6 weeks. Cell recruitment to the surfaces was quantified by acridine orange staining and specific antibodies directed against cell membrane antigens. Removal torque, bone-to-metal contact, total bone area and histological evaluations were used to evaluate fixture stability and the healing-in of the implants. After the healing period of 6 weeks only a transient significant difference was seen in the total number of cells adherent on the surfaces. No significant differences were observed between any of the surfaces for removal torque, bone-to-metal contact, or bone area. The areas lacking bone-to-metal contact were filled with normal vascularised connective tissue with no signs of fibrous capsule formation or giant cells. These findings differ from findings published earlier of Ti implants that underwent a cleaning regimen with alcohol as the final rinsing step. The tissues around the implants were richly vascularised and there was continued bone growth toward the surfaces. The bone-to-metal contact in this study was lower than that seen with alcohol-cleaned TiO2.