Self-assembly preparation of lignin–graphene oxide composite nanospheres for highly efficient Cr(vi) removal

Recently, research interest in the application of lignin is growing, especially as adsorbent material. However, single lignin shows unsatisfactory adsorption performance, and thus, construction of lignin-based nanocomposites is worth considering. Herein, we introduced graphene oxide (GO) into lignin to form lignin/GO (LGNs) composite nanospheres by a self-assembly method. FTIR and ¹H NMR spectroscopy illustrated that lignin and GO are tightly connected by hydrogen bonds. The LGNs as an environmental friendly material, also exhibit excellent performance for Cr(vi) removal. The maximum sorption capacity of LGNs is 368.78 mg g⁻¹, and the sorption efficiency is 1.5 times than that of lignin nanospheres (LNs). The removal process of Cr(vi) via LGNs mainly relies on electrostatic interaction, and it also involves the reduction of Cr(vi) to Cr(iii). Moreover, LGNs still have high adsorption performance after repeating five times with the sorption capacity of 150.4 mg g⁻¹ in 200 mg g⁻¹ Cr(vi) solution. Therefore, the prepared lignin–GO composite nanospheres have enormous potential as a low-cost, high-absorbent and recyclable adsorbent, and can be used in wastewater treatment.

Lignin/GO (LGNs) composite nanospheres were prepared by self-assembly method, which showed excellent adsorption performance for Cr(vi) removal.     

Characterization of CMC–LDH beads and their application in the removal of Cr(vi) from aqueous solution

In this study, CMC–LDH beads were prepared and characterized using SEM, FTIR and TG analysis. The beads were applied for the removal of Cr(vi) from aqueous solution. The effects of adsorbent dosage, initial pH and initial concentration of Cr(vi) solution on Cr(vi) uptake were investigated in detail. Moreover, adsorption isotherms and adsorption kinetic models were employed to analyze the adsorption process, and a preliminary study of the reusability of the adsorbent was performed. The experimental results showed that the CMC–LDH beads could remove Cr(vi) from aqueous solution efficiently. When the initial concentration of the Cr(vi) solution was 100 mg L⁻¹ and the adsorbent dosage was 12 g L⁻¹, the removal efficiency of Cr(vi) reached 96.2%. After the CMC–LDH beads were reused 10 times, the removal efficiency of Cr(vi) still remained at 89.6%.

CMC–LDH beads were prepared, characterized and applied for the removal of heavy metal ions in this study.     

Removal of Pb(ii) and Cr(vi) from aqueous solutions using the prepared porous adsorbent-supported Fe/Ni nanoparticles

In this study, Fe/Ni nanoparticles supported by a novel fly ash-based porous adsorbent (FBA-Fe/Ni) for Cr(vi) and Pb(ii) removal were investigated. In order to enhance the reactivity of zero-valent iron (ZVI), ZVI particles were deposited on the surface or in the inner pores of FBA as a support material and Ni nanoparticles were introduced. FBA was prepared with the solid waste such as Enteromorpha prolifera, bentonite and fly ash. FBA-Fe/Ni was characterized via Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and the Brunauer–Emmett–Teller model and energy-dispersive spectrometry. The effects of various parameters on Cr(vi) and Pb(ii) removal by FBA-Fe/Ni, such as FBA-Fe/Ni dosage, pH of the solution, reaction temperature, Cr(vi) and Pb(ii) concentrations, co-existing ions and ionic strength were discussed. The possible removal mechanisms were proposed and the results indicated that there was a three-step reaction including the adsorption of Cr(vi) and Pb(ii) on the surface of FBA-Fe/Ni, the subsequent reduction and precipitation. The removal capacity of Cr(vi) and Pb(ii) by FBA-Fe/Ni was 25.07 mg g⁻¹ and 164.19 mg g⁻¹ at 303 K with an initial concentration of 1000 mg L⁻¹ and FBA-Fe/Ni dosage of 0.20 g. In conclusion, this work demonstrated that FBA-Fe/Ni was a promising alternative material for Cr(vi) and Pb(ii) removal.

In this study, Fe/Ni nanoparticles supported by a novel fly ash-based porous adsorbent (FBA-Fe/Ni) for Cr(vi) and Pb(ii) removal were investigated.     

Biosorption of Cr(vi) from aqueous solution using dormant spores of Aspergillus niger

Spores of Aspergillus niger (denoted as A. niger) were used as a novel biosorbent to remove hexavalent chromium from aqueous solution. The effects of biosorbent dosage, pH, contact time, temperature and initial concentration of Cr(vi) on its adsorption removal were examined in batch mode. The Cr(vi) uptake capacity increased with an increase in Cr(vi) concentration until saturation, which was found to be about 97.1 mg g⁻¹ at pH 2.0, temperature of 40 °C, adsorbent dose of 2.0 g L⁻¹ and initial concentration of 300 mg L⁻¹. Scanning electron microscopy, energy dispersive X-ray spectroscopy, field-emission transmission electron microscopy (FETEM), XPS and Fourier-transform infrared spectroscopy were applied to study the microstructure, composition and chemical bonding states of the biomass adsorbent before and after spore adsorption. The mechanisms of chromate anion removal from aqueous solution by the spores of A. niger were proposed, which included adsorption of Cr(vi) onto the spores followed by its reduction to Cr(iii). The reduced Cr(iii) was rebound to the biomass mainly through complexation mechanisms, redox reaction and electrostatic attraction. The removal of Cr(vi) by spores of A. niger followed pseudo-second-order adsorption kinetics. Monolayer adsorption of Cr(vi) was revealed by the better fitting of the Langmuir model isotherm rather than multilayer adsorption for the Freundlich model. The results indicated that A. niger spores can be used as a highly efficient biosorbent to remove Cr(vi) from contaminated water.

Spores of Aspergillus niger (denoted as A. niger) were used as a novel biosorbent to remove hexavalent chromium from aqueous solution.     

Efficient removal of hexavalent chromium from water by an adsorption–reduction mechanism with sandwiched nanocomposites

Hexavalent chromium Cr(vi), one of the most toxic contaminants, is released in the environment due to various anthropogenic activities. This study presents a novel sandwiched nanocomposite synthesized using graphene oxide (GO), manganese dioxide (MnO₂) nanowires, iron oxide (Fe₃O₄) nanoparticles and polypyrrole (PPy) to remove hexavalent chromium ion Cr(vi) from water by an adsorption–reduction mechanism. In the sandwiched nanocomposites, GO provided enough surface area, functional groups, and hydrophilic surface for efficient absorption. Fe₃O₄ nanoparticles with excellent magnetic properties make it easy to separate and recover from water. Under acidic conditions, MnO₂ nanowires act as both template and oxidant to initiate the polymerization of pyrrole monomers on its freshly activated surface to obtain GO/MnO₂/Fe₃O₄/PPy (designated as GMFP) nanocomposite. GMFP could effectively adsorb Cr(vi) through electrostatic attraction, and the adsorbed Cr(vi) ions were partly reduced to trivalent chromium Cr(iii) (62%), resulting in the efficient adsorption and high removal of Cr(vi) from water. Hexavalent chromium adsorption by GMFP is strongly pH dependent and the adsorption kinetics followed the pseudo-second-order model. The Langmuir isothermal model described the adsorption isotherm data well and the maximum adsorption capacity was up to 374.53 mg g⁻¹ at pH 2.0. These experimental results suggested that GMFP had great potential as an economic and efficient adsorbent of hexavalent chromium from wastewater, which has huge application potential.

A sandwiched nanocomposite has been developed to remove hexavalent chromium ion Cr(vi) from water by an adsorption–reduction mechanism.     

Recyclable functionalized polymer films for the efficient removal of hexavalent chromium from aqueous solutions

In this study, polyethylenimine-functionalized poly(vinyl alcohol) (PEI-PVA) films were prepared for the first time to remove aqueous Cr(vi). The results indicate that our PEI-PVA films have an excellent potential for Cr(vi) removal and their maximum removal capacity was 396.83 mg g⁻¹. The optimized pH value was 2, the adsorption of Cr(vi) was fitted to the Langmuir model, and the kinetics of uptake could be described well by a pseudo-second-order rate model. Taking into account the simplified separation method of adsorbents and solutions, we used a PVA film as a carrier in which PEI-PVA microspheres were filled to obtain a PEI-PVA functionalized film (PPF). The PPF shows a great efficiency in the removal of Cr(vi) ions in solution, which can absorb and reduce the Cr(vi) ion concentration in the solution in 90 min. PPF has excellent selectivity and the removal efficiency of Cr(vi) ions in the presence of co-existing ions is not reduced. It also has good recycling properties; the removal efficiency remains at 77% over four cycles. The removal mechanism of Cr(vi) ions by PEI-PVA microspheres involves the reduction of the adsorbed Cr(vi) ions to Cr(iii) ions, which are less toxic.

A PEI-PVA functionalized composite film has been developed to remove hexavalent chromium ion Cr(vi) from water by an adsorption–reduction mechanism.     

Adsorption and reduction of hexavalent chromium on magnetic greigite (Fe3S4)-CTAB: leading role of Fe(ii) and S(−ii)

In this study, a facile one-step route was used to synthesize a novel magnetic mesoporous greigite (Fe₃S₄)-CTAB composite, which was utilized to remove hexavalent chromium (Cr(vi)). The optimized Fe₃S₄-CTAB_0.75 composite with a CTAB dosage of 0.75 g possessed the maximum specific surface, showing the highest Cr(vi) adsorption capacity of 330.03 mg g⁻¹. The mechanism analysis revealed that Fe(ii) and S(−ii) were critical for the reduction of Cr(vi). CTAB can promote the removal of Cr(vi) by Fe₃S₄-CTAB composites, possibly due to increased S(−ii) concentration, better dispersion of nanoparticles, and greater zeta potential. Besides, there is mild effect of Fe⁰ on Cr(vi) removal, which is confirmed by the disappearance of the Fe⁰ peak from the XPS analysis. The pseudo-second-order kinetic model could explain the Cr(vi) removal processes well. The adsorption of Cr(vi) at different initial concentrations was more consistent with a Langmuir isotherm. The existence of H⁺ was beneficial for Cr(vi) removal by Fe₃S₄-CTAB_0.75. Our work confirmed that the obtained Fe₃S₄-CTAB_0.75 composites exhibit considerable potential for Cr(vi) removal from aqueous solution.

The presence of CTAB can promote the removal of hexavalent chromium from the Fe₃S₄-CTAB surface.     

Freezing/thawing pretreatment of dormant Aspergillus niger spores to increase the Cr(vi) adsorption capacity: process and mechanism

Hexavalent chromium is a widespread pollutant that threatens ecological and human health. However, its removal from the environment is limited by the high cost and energy consumption rate of current technologies. In this study, the Cr(vi) biosorption mechanism of Aspergillus niger spores pretreated by freezing/thawing was studied by batch experiments and surface chemistry analyses. The results indicated that pretreatment enhanced the spores'' Cr(vi) removal efficiency. The cell surface, internal functional groups, and morphology of the freezing/thawing-pretreated spores (FTPS) before and after Cr(vi) loading were characterized by advanced spectroscopy techniques such as SEM-EDAX, XPS, FTIR, and FETEM analyses. The SEM and BET data showed that the surface of FTPS was rougher than that of untreated spores. The XPS data showed that FTPS bio-transformed Cr(vi) into Cr(iii). The intracellular localization of chromium was visualized by FETEM, and both surface and intracellular structures removed Cr(vi) following pseudo-second-order biosorption kinetics. The biosorption dynamics of Cr(vi) fit the Langmuir isotherm model describing a monolayer. These results suggest that freezing/thawing pretreatment of A. niger spores could lead to the development of a novel, efficient biomaterial for the removal of Cr(vi).

Freezing/thawing pretreatment of A. niger spores could lead to the development of a novel, efficient biomaterial for the removal of Cr(vi).     

Effective removal of Cr(vi) from aqueous solution by biochar supported manganese sulfide

In order to remove hexavalent chromium (Cr(vi)) efficiently and simplify the adsorbent preparation process, we employed a single step method to prepare a new biochar supported manganese sulfide material. The nanoscale MnS particles were highly soldered on the biochar support surface, and this adsorbent displayed the effective removal of Cr(vi) (98.15 mg L⁻¹) via synergistic effect between adsorption and reduction/precipitation under weak acid conditions (pH = 5.0–6.0). The adsorption kinetic data were described well by the pseudo second-order kinetic model, suggesting that the reaction process was a chemisorption process. The adsorption isotherm data were described well by the Redlich–Peterson model, further suggesting that this reaction was a hybrid chemical reaction-sorption process. In addition, the Dubinin–Radushkevich isotherm model with 8.28, 8.57, and 12.91 kJ mol⁻¹ adsorption energy also suggests that it was a chemisorption process. The simple and eco-friendly preparation process, low-cost, and the high removal efficiency could make it a promising material for the purification of Cr(vi)-contaminated wastewater.

In order to remove hexavalent chromium (Cr(vi)) efficiently and simplify the adsorbent preparation process, we employed a single step method to prepare a new biochar supported manganese sulfide material.     

Fe(iii) and Cr(vi) ions' removal using AgNPs/GO/chitosan nanocomposite as an adsorbent for wastewater treatment

Heavy metal ions in water refer to significant risks to the biological system due to their high toxicity. Therefore, the decontamination of water polluted by heavy metal ions attracts significant interest of researchers. Adsorption by nanomaterials has been a widely used technique for removing heavy metal ions from water. Chitosan was extracted from shrimp shellfish and mixed with laboratory-prepared AgNPs/GO in the ratio of 3 : 1. A series of tests evaluates the best condition of pH, amount of adsorbent, retention time, stirring speed, temp, and initial concentration. The research was conducted under various conditions. Langmuir, Freundlich, Tempkin, and Dubinin–Radushkevich isotherms were also tested. Also, the column adsorption experiment was carried out on industrial wastewater at different flow rates and column bed heights. The optimal values of the contact time, pH, and adsorbent dose of Cr(vi) were found to be 80 min, 4, and 0.1 g 100 mL⁻¹, respectively, at room temperature (30 °C), agitation at 150 rpm, and initial concentration of 50 ppm. On the other hand, the optimal value of contact time, pH, and adsorbent dose of Fe(iii) were found to be 30 min, 6, and 0.02 g 100 mL⁻¹, respectively, at room temp (30 °C) with a stirring speed of 250 rpm and an initial concentration of 40 ppm. For Cr(vi) and Fe(iii), equilibrium studies show that the data fit the Freundlich isotherm well (correlation coefficient, R² = 0.98) (III). A link between the pseudo-second order active model and data fitting the pseudo-first order active models were made. Within the intraparticle diffusion model, there are four stages that the mechanism must go through before it is at equilibrium. The adsorbent was tested in an industrial adsorbent column. This test proves that the nanocomposite''s adsorption capacity can be restored by washing it with 0.1 M HCl, as shown by the periodicity test. After four cycles, the amount of Cr(vi) adsorbed on AgNPs/GO/chitosan was just 20%, which is insufficient for further adsorption experiments. Cr(vi) removal rates (%R) decreased slightly.

Steps of AgNPs/GO/chitosan nanocomposite preparation.     

Mechanism and modeling of hexavalent chromium interaction with a typical black soil: the importance of the relationship between adsorption and reduction

Black soils have a significant retention effect on the migration of Cr(vi) towards groundwater, and Cr(vi) adsorption and reduction are both involved in this process. However, the adsorption and reduction of Cr(vi) were always investigated separately in previous studies resulting in an unclear relationship between them. In this study, the adsorption and reduction kinetic processes of Cr(vi) by a typical black soil were separately investigated under different initial Cr(vi) concentrations (40–400 mg L⁻¹) and pH conditions (3.5–7.0) by the means of desorption treatment, and the equilibrium relationship between aqueous and adsorbed Cr(vi) was innovatively established based on the kinetic data. It was found that under pH 5.7 the adsorbed Cr(vi) content on soil particles was linearly correlated with the remaining Cr(vi) concentration in solution with time (R² = 0.98), and the reduction rate of Cr(vi) in the reaction system was linearly correlated with the adsorbed Cr(vi) content on soil particles with time (R² = 0.99). With pH decreasing from 7.0 to 3.5, the partition of Cr(vi) between solid and aqueous phases turned out to be of a non-linear nature, which can be fitted better by the Freundlich model. The retention of Cr(vi) by black soil was determined to follow the “adsorption–reduction” mechanism, where the Cr(vi) was first rapidly adsorbed onto the soil particles by a reversible adsorption reaction, and then the adsorbed Cr(vi) was gradually reduced into Cr(iii). A two-step kinetic model was developed accordingly, and the experimental data were fitted much better by the two-step adsorption–reduction kinetic model (R² = 0.89 on average) compared with the traditional first-order and second-order kinetic models (R² = 0.66 and 0.76 on average respectively). This paper highlights the novel two step kinetic model developed based on the proposed “adsorption–reduction” mechanism of Cr(vi) retention by a typical black soil.

A novel two-step kinetic model was developed based on the proposed “adsorption–reduction” mechanism of Cr(vi) retention by a typical black soil.     

Surfactant-assisted hydrothermal synthesis of rGO/SnIn4S8 nanosheets and their application in complete removal of Cr(vi)

To solve the problem of contamination of hexavalent chromium (Cr(vi)), visible-light-driven graphene-based ternary metal chalcogenide nanosheets (rGO/SnIn₄S₈) were synthesized via a one-pot surfactant-assisted hydrothermal method for the photoreduction of Cr(vi). Characterizations demonstrated that SnIn₄S₈ nanosheets were uniformly distributed on the surface of rGO and the as-synthesized nanosheets exhibited excellent photocatalytic activity under visible light. In addition, the effects of pH, concentration of critic acid, holes and electron scavengers on the reduction of Cr(vi) were systematically investigated. It was found that 50 mg L⁻¹ of Cr(vi) could be completely removed within 30 min at pH 2 when citric acid served as a hole scavenger. Kinetic studies showed that the photocatalytic reduction of Cr(vi) processes obeyed the pseudo first order model. Further study indicated that the Cr(iii) species was immediately adsorbed onto the surface of the rGO/SnIn₄S₈ nanosheets after photocatalytic reduction of Cr(vi). Additionally, recycling results suggested that rGO/SnIn₄S₈ nanosheets possessed high recycle ability and stability after repeated use (5 times). This effective and promising work might provide a new strategy for the photoreduction of Cr(vi) and complete removal of chromium from effluent through the novel photocatalyst rGO/SnIn₄S₈.

Fabrication of visible-light-responsive photocatalyst (rGO/SnIn₄S₈) for photoreduction of Cr(vi) and adsorption of Cr(iii).     

Facile preparation of hybrid porous polyanilines for highly efficient Cr(vi) removal

In the present work, leucoemeraldine-based hybrid porous polyanilines (LHPPs) have been synthesized by the Friedel–Crafts reaction of leucoemeraldine and octavinylsilsesquioxane (OVS) for Cr(vi) removal. The resulting LHPPs were characterized by Fourier transform infrared spectroscopy, powder X-ray diffraction, thermogravimetric analysis, scanning electron microscopy and N₂ adsorption–desorption. The findings indiated that the LHPPs were amorphous, with apparent surface areas (S_BET) in the range of 147 to 388 m² g⁻¹ and total volumes in the range of 0.13 to 0.44 cm³ g⁻¹. Cr(vi) removal experiments displayed that the LHPPs exhibited highly efficient Cr(vi) removal performance. The maximum Cr(vi) removal capacity of LHPP-1 was 990.1 mg g⁻¹ at 308 K and pH 1, which is higher than those of other reported polyaniline-based adsorbents. The adsorption process was a spontaneous, endothermic and chemical adsorption process. The adsorption behavior agreed well with Langmuir models and pseudo second-order equations. X-ray photoelectron spectroscopy and Fourier transformed infrared (FTIR) spectroscopy analysis revealed that the highly efficient Cr(vi) removal performance can be mainly attributed to the existence of numerous amine and imine groups on the surface of the LHPPs; these can function as adsorption active sites for Cr(vi) removal through electrostatic adsorption and reduction to Cr(iii) under acidic conditions. Moreover, the LHPPs exhibited excellent adsorption selectivity for Cr(vi) despite the presence of other metal ions (K⁺, Cu²⁺, Mn²⁺) and anions (NO₃⁻, SO₄²⁻). Therefore, the LHPPs have potential applications for Cr(vi) removal in industrial wastewater.

In the present work, leucoemeraldine-based hybrid porous polyanilines (LHPPs) have been synthesized by the Friedel–Crafts reaction of leucoemeraldine and octavinylsilsesquioxane (OVS) for Cr(vi) removal.     

Efficient removal of chromate ions from aqueous solution using a highly cost-effective ferric coordinated [3-(2-aminoethylamino)propyl]trimethoxysilane–MCM-41 adsorbent

The present investigation involves synthesis and characterization of MCM-41–AEAPTMS–Fe(iii)Cl using coordinated Fe(iii) on MCM-41–AEAPTMS for efficient removal of hazardous Cr(vi) ions from aqueous solution. The adsorbent MCM-41–AEAPTMS–Fe(iii)Cl was characterized using small-angle X-ray diffraction (SAX), transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), Fourier-transform infrared (FT-IR) and Brunauer–Emmett–Teller (BET) surface analyzer techniques. The BET surface area was found to be 87.598 m² g⁻¹. The MCM-41–AEAPTMS–Fe(iii)Cl effectively adsorbs Cr(vi) with an adsorption capacity acquiring the maximum value of 84.9 mg g⁻¹ at pH 3 at 298 K. The data followed pseudo-second-order kinetics and obeyed the Langmuir isotherm model. The thermodynamic data proved the exothermic and spontaneous nature of Cr(vi) ion adsorption on MCM-41–AEAPTMS–Fe(iii). Further, the higher value of ΔH° (−64.339 kJ mol⁻¹) indicated that the adsorption was chemisorption in nature.

The present investigation involves synthesis and characterization of MCM-41–AEAPTMS–Fe(iii)Cl using coordinated Fe(iii) on MCM-41–AEAPTMS for efficient removal of hazardous Cr(vi) ions from aqueous solution.     

Insight into the synergistic effect on adsorption for Cr(vi) by a polypyrrole-based composite

Polypyrrole-based (PPy) composite are promising candidates for the treatment of water pollution. Adsorption selectivity as well as a large adsorption capacity are two key factors for treating wastewater containing multiple ions. The structure and morphology of the prepared composites were characterized by the FT-IR, XRD and SEM examinations. The results indicate that the Fe₃O₄ and PPy nanosphere coats attapulgite (ATP) closely and evenly. Herein, a novel Fe₃O₄ and ATP doped three-dimensional network structure PPy/Fe₃O₄/ATP composite was demonstrated as an excellent adsorbent to effectively remove Cr(vi). The as-synthesized PPy/Fe₃O₄/ATP composite is suitable for Cr(vi) adsorption in a wide pH range (pH 2–6). Up to a 96.44% removal rate was found with 400 mg L⁻¹ Cr(vi) aqueous solution in 30 min for 0.2 g PPy/Fe₃O₄/ATP adsorbent. Adsorption results showed that Cr(vi) removal efficiency by PPy/Fe₃O₄/ATP decreased with an increase in pH. The removal rate of Cr(vi) had already reached 93.63% in 15 min contact time. Co-existing ions studies exhibit inorganic oxyacid anion and transition metal cation showed negative effects on Cr(vi) removal rate. A chemical rather than a physical adsorption occurred for these adsorbents as revealed by a pseudo-second-order kinetic study. The results of the adsorption isotherms showed that the adsorption process was similar to the Langmuir isotherm adsorption. Furthermore, the PPy/Fe₃O₄/ATP composite exhibited a high stability for Cr(vi) adsorption during recycling tests process. This work may provide some useful guidelines for designing adsorbents with selectivity toward specific heavy metal ions.

Polypyrrole-based (PPy) composite are promising candidates for the treatment of water pollution.     

Preparation and application synthesis of magnetic nanocomposite using waste toner for the removal of Cr(vi)

In this study, a novel magnetic nanocomposite was prepared using waste toner (WT) through high temperature decomposition, and calcination was conducted in different atmospheres (air, ammonia, and vacuum). WT calcined in ammonia (WT(NH₃)), and it was then utilized as an efficient absorbent for the reduction of Cr(vi) in aqueous solutions; a batch experiment with different conditions was performed to investigate its Cr(vi) removal ability. The effects of two pH-regulating acid (HCl and H₂SO₄) treatments were also studied. It was found that WT(NH₃) could remove about 99% Cr(vi) at pH 2 under H₂SO₄ treatment. The XRD and TEM results coupled with VSM results confirmed that WT(NH₃) is an Fe₃O₄/Fe₂N nanohybrid, which possesses excellent water-dispersibility and remarkable magnetic properties. XPS analysis showed the presence of Cr(vi) and Cr(iii) on the surface of WT(NH₃), which indicated that Cr(vi) was reduced to Cr(iii). Furthermore, H₂SO₄ regulation also promoted the reduction of Cr(vi) by WT(NH₃), and this reduction was higher than that obtained by HCl regulation.

A novel magnetic nanocomposite is prepared using waste toner via calcination in ammonia, which exhibits excellent magnetic properties and high efficiency for the removal of Cr(vi) via pH regulation using H₂SO₄.     

Positive effects of concomitant heavy metals and their reduzates on hexavalent chromium removal in microbial fuel cells

Cr(vi) laden wastewaters generally comprise a range of multiple heavy metals such as Au(iii) and Cu(ii) with great toxicity. In the present study, cooperative cathode modification by biogenic Au nanoparticles (BioAu) reduced from aqueous Au(iii) and in situ Cu(ii) co-reduction were investigated for the first time to enhance Cr(vi) removal in microbial fuel cells (MFCs). With the co-existence of Cu(ii) in the catholyte, the MFC with carbon cloth modified with nanocomposites of multi-walled carbon nanotubes blended with BioAu (BioAu/MWCNT) obtained the highest Cr(vi) removal rate (4.07 ± 0.01 mg L⁻¹ h⁻¹) and power density (309.34 ± 17.65 mW m⁻²), which were 2.73 and 3.30 times as high as those for the control, respectively. The enhancements were caused by BioAu/MWCNT composites and deposited reduzates of Cu(ii) on the cathode surface, which increased the adsorption capacity, electronic conductivity and electrocatalytic activity of the cathode. This study provides an alternative approach for efficiently remediating co-contamination of multiple heavy metals and simultaneous bioenergy recovery.

The cooperative cathode modification by BioAu from Au(iii) and in situ Cu(ii) co-reduction enhanced Cr(vi) removal and bioelectricity generation in MFCs.     

High dispersions of nano zero valent iron supported on biochar by one-step carbothermal synthesis and its application in chromate removal

A one-step carbothermal synthesis and characterization of biochar-supported nanoscale zero-valent iron (nZVI/BC) was performed for the removal of hexavalent chromium (Cr(vi)) from aqueous solution. High dispersions of nanoscale zero-valent iron supported on biochar were successfully synthesized by the pyrolysis of an iron-impregnated biomass (corn stover) as the carbon and iron source under nitrogen atmosphere. The effects of the pyrolytic temperature on the Fe mineralogies formed on the biochar are discussed. In general, the effects of the treatment time, initial solution pH, and nZVI/BC dosage on the Cr(vi) removal are presented. The results showed high crystallinity and purity, and nZVI/BC was obtained at a pyrolytic temperature of 800 °C. The batch experimental results determined that the adsorption capacity of Cr(vi) decreases with the increase in the initial pH value from 4.0 to 10.0. The Cr(vi) adsorption kinetics data effectively followed a pseudo-second-order kinetics with a calculated rate constant of 0.0.3396 g mg⁻¹ min⁻¹. The calculated thermodynamic parameters, such as ΔG°, ΔH°, and ΔS°, were evaluated, and the results indicated that the Cr(vi) reduction on nZVI/BC was a spontaneous and endothermic process. The adsorption mechanism of Cr(vi) was investigated by XRD and XPS analyses and the results demonstrated that Cr(vi) was reduced to Cr(iii) and the oxidation of nZVI occurred during the reaction process. These results prove that nZVI/BC synthesized by a one-step carbothermal method can be considered as a potential candidate for the removal of Cr(vi) from aqueous solutions.

A one-step carbothermal synthesis and characterization of biochar-supported nanoscale zero-valent iron (nZVI/BC) was performed for the removal of hexavalent chromium (Cr(vi)) from aqueous solution.     

High capacity and fast removal of Cr(vi) by alkali lignin-based poly(tetraethylene pentamine-pyrogallol) sorbent

In this work, a novel alkali lignin-based adsorption material, alkali lignin-based poly(tetraethylene pentamine-pyrogallol) (AL-PTAP), was prepared using a Mannich reaction and catechol-amine reaction for removal of Cr(vi). It was characterized by thermogravimetric analysis (TGA), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The effects of tetraethylene pentamine (TEPA) dosage, pyrogallol (PL) dosage, contact time, pH, temperature and other factors on the adsorption behavior of the adsorbent were systematically investigated. These experimental data show that the adsorption behavior conforms to the pseudo-second-order kinetic model and the Langmuir isotherm model. The maximum adsorption capacity is 769.2 mg g⁻¹ at 303 K, which is much higher than that of alkali lignin (AL). AL-PTAP can achieve a removal rate of almost 100% for Cr(vi) solutions with a concentration of less than 90 mg L⁻¹ at 1 min. Furthermore, the toxic Cr(vi) is partly reduced to nontoxic Cr(iii) during the adsorption process. Therefore, AL-PTAP is a fast and efficient alkali lignin-based adsorbent, which is expected to improve the utilization value of alkali lignin in Cr(vi) wastewater treatment.

The alkali lignin-based poly(tetraethylene pentamine-pyrogallol) (AL-PTAP) was prepared with an adsorption capacity of 769.2 mg g⁻¹ and a removal percentage of almost 100% within 1 min at an initial concentration of less than 90 mg L⁻¹.     

Synthesis and evaluation of ion-imprinted composite membranes of Cr(vi) based on β-diketone functional monomers

Using Cr(vi) as the imprinted ions and 2-allyl-1,3-diphenyl-1,3-propanedione (ADPD) (a compound synthesized by independent design) as the functional monomer, a series of chromium ion-imprinted composite membranes (Cr(vi)-IICMs) and corresponding non-imprinted composite membranes (NICMs) were synthesized and tested. The results showed that the Cr(vi)-IICM₁₀ membrane prepared under optimal experimental conditions exhibited a high adsorption capacity towards Cr(vi) (Q = 30.35 mg g⁻¹) and a high imprinting factor (α = 2.70). The structural characteristics of Cr(vi)-IICM₁₀ and NICM₁₀ were investigated using FE-SEM, ATR-FTIR, and BET techniques combined with UV-Vis photometry and inductively coupled plasma emission spectrometry (ICP-OES) to evaluate the adsorption performance and permeation selectivity, while the effect on adsorption permeance of varying the experimental conditions including the solvent type, pH, and temperature was also investigated. The results showed that Cr(vi)-IICM₁₀ is a mesoporous material with excellent permeation selectivity, reusability, and favorable pH response, and that its adsorption behavior is in accordance with the Langmuir model and pseudo-first-order kinetics. Thus, Cr(vi)-IICM₁₀ shows great potential towards utilization as a “smart membrane” to control the separation and removal of Cr(vi) in wastewater, and also proved a reasonable design of the new functional monomer ADPD.

Using Cr(vi) as the imprinted ions and 2-allyl-1,3-diphenyl-1,3-propanedione (a compound of independent design) as the functional monomer, a series of chromium ion-imprinted composite membranes and corresponding non-imprinted composite membranes were synthesized and tested.