Sucrose-templated interconnected meso/macro-porous 2D symmetric graphitic carbon networks as supports for α-Fe2O3 towards improved supercapacitive behavior

In this study, ultrahigh electrochemical performance for interconnected meso/macro-porous 2D C@α-Fe₂O₃ synthesized via sucrose-assisted microwave combustion is demonstrated. Hematite (α-Fe₂O₃) synthesized via the same approach gave an encouraging electrochemical performance close to its theoretical value, justifying its consideration as a potential supercapacitor electrode material; nonetheless, its specific capacitance was still low. The pore size distribution as well as the specific surface of bare α-Fe₂O₃ improved from 145 m² g⁻¹ to 297.3 m² g⁻¹ after it was coated with sucrose, which was endowed with ordered symmetric single-layer graphene (2D graphene). Accordingly, the optimized hematite material (2D C@α-Fe₂O₃) showed a specific capacitance of 1876.7 F g⁻¹ at a current density of 1 A g⁻¹ and capacity retention of 95.9% after 4000 cycles. Moreover, the material exhibited an ultrahigh energy density of 93.8 W h kg⁻¹ at a power density of 150 W kg⁻¹. The synergistic effect created by carbon-coating α-Fe₂O₃ resulted in modest electrochemical performance owing to extremely low charge transfer resistance at the electrode–electrolyte interface with many active sites for ionic reactions and efficient diffusion process. This 2D C@α-Fe₂O₃ electrode material has the capacity to develop into a cost-effective and stable electrode for future high-energy-capacity supercapacitors.

In this study, ultrahigh electrochemical performance for interconnected meso/macro-porous 2D C@α-Fe₂O₃ synthesized via sucrose-assisted microwave combustion is demonstrated.     

Magnetic hyperthermia with ε-Fe2O3 nanoparticles

Biocompatibility restrictions have limited the use of magnetic nanoparticles for magnetic hyperthermia therapy to iron oxides, namely magnetite (Fe₃O₄) and maghemite (γ-Fe₂O₃). However, there is yet another magnetic iron oxide phase that has not been considered so far, in spite of its unique magnetic properties: ε-Fe₂O₃. Indeed, whereas Fe₃O₄ and γ-Fe₂O₃ have a relatively low magnetic coercivity, ε-Fe₂O₃ exhibits a giant coercivity. In this report, the heating power of ε-Fe₂O₃ nanoparticles in comparison with γ-Fe₂O₃ nanoparticles of similar size (∼20 nm) was measured in a wide range of field frequencies and amplitudes, in uncoated and polymer-coated samples. It was found that ε-Fe₂O₃ nanoparticles primarily heat in the low-frequency regime (20–100 kHz) in media whose viscosity is similar to that of cell cytoplasm. In contrast, γ-Fe₂O₃ nanoparticles heat more effectively in the high frequency range (400–900 kHz). Cell culture experiments exhibited no toxicity in a wide range of nanoparticle concentrations and a high internalization rate. In conclusion, the performance of ε-Fe₂O₃ nanoparticles is slightly inferior to that of γ-Fe₂O₃ nanoparticles in human magnetic hyperthermia applications. However, these ε-Fe₂O₃ nanoparticles open the way for switchable magnetic heating owing to their distinct response to frequency.

ε-Fe₂O₃ is a magnetic iron(iii) oxide with a giant coercivity. Its potential in hyperthermia applications has been evaluated in comparison with γ-Fe₂O₃ over a wide range of field frequencies and amplitudes.     

Mesoporous anodic α-Fe2O3 interferometer for organic vapor sensing application

In this work, we reported the utilization of mesoporous α-Fe₂O₃ films as optical sensors for detecting organic vapors. The mesoporous α-Fe₂O₃ thin films, which exhibited obvious Fabry–Perot interference fringes in the reflectance spectrum, were successfully fabricated through electrochemical anodization of Fe foils. Through monitoring the optical thickness of the interference fringes, three typical organic species with different vapor pressures and polarities (hexane, acetone and isopropanol) were applied as probes to evaluate the sensitivity of the α-Fe₂O₃ based interferometric sensor. The experiment results showed that the as-synthesized mesoporous α-Fe₂O₃ interferometer displayed high reversibility and stability for the three organic vapors, and were especially sensitive to isopropanol, with a detection limit of about 65 ppmv. Moreover, the photocatalytic properties of α-Fe₂O₃ under visible light are beneficial for degradation of dodecane vapor residues in the nano-pores and refreshment of the sensor, demonstrating good self-cleaning properties of the α-Fe₂O₃-based interferometric sensor.

Mesoporous α-Fe₂O₃ interferometers with well-resolved optical fringes can display high sensitivity to organic vapors.     

MOF-derived (MoS2, γ-Fe2O3)/graphene Z-scheme photocatalysts with excellent activity for oxygen evolution under visible light irradiation

Constructing Z-scheme heterojunctions is considered as an effective strategy to obtain catalysts of high efficiency in electron–hole separation in photocatalysis. Unfortunately, suitable heterojunctions are difficult to fabricate because the direct interaction between two semiconductors may lead to unpredictable negative effects such as electron scattering or electron trapping due to the existence of defects which causes the formation of new substances. Furthermore, the van der Waals contact between two semiconductors also results in bad electron diffusion. In this work, a MOF-derived carbon material as a Z-scheme photocatalyst was synthesized via one-step thermal treatment of MoS₂ dots @Fe-MOF (MIL-101). Under visible light irradiation, the well-constructed Z-scheme (MoS₂, γ-Fe₂O₃)/graphene photocatalyst shows 2-fold photocatalytic oxygen evolution activity (4400 μmol g⁻¹ h⁻¹) compared to that of γ-Fe₂O₃/graphene (2053 μmol g⁻¹ h⁻¹). Based on ultraviolet photoelectron spectrometry (UPS), Mott–Schottky plot, photocurrent and photoluminescence spectroscopy (PL) results, the photo-induced electrons from the conduction band of γ-Fe₂O₃ could transport quickly to the valence band of MoS₂via highly conductive graphene as an electron transport channel, which could significantly enhance the electron–hole separation efficiency as well as photocatalytic performance.

The heterojunction between MoS₂ and γ-Fe₂O₃ was constructed via linking by in situ formed graphene, which resulted in a good photocatalyst for the oxygen evolution reaction, showing O₂ evolution activity of 4400 μmol g⁻¹ h⁻¹.     

DFT study on the electronic structure and optical properties of an Au-deposited α-Fe2O3 (001) surface

The electronic structure and optical properties of gold clusters deposited on an α-Fe₂O₃ surface were studied by using density functional theory (DFT), with a special emphasis on the influence of Au cluster sizes. There is a strong interaction between Au clusters and the α-Fe₂O₃ surface, and the binding energy increases with an increase of Au cluster size. The Au atoms of the gold cluster are bonded to the iron atoms of the α-Fe₂O₃ surface for the Au/α-Fe₂O₃ system, and the electrons transfer from the Au cluster to the α-Fe₂O₃ surface with the largest number of electrons transferred for 4Au/α-Fe₂O₃. The peaks of the refractive index, extinction coefficient and dielectric function induced by Au clusters appear in the visible range, which results in the enhanced optical absorption for the Au/α-Fe₂O₃ system. The optical absorption intensifies with increasing Au cluster size in the visible range, showing a maximum value for 4Au/α-Fe₂O₃. Further increasing the Au cluster size above 4Au results in a decrease in absorption intensity. The results are in good agreement with those of the refractive index, extinction coefficient and dielectric function.

The electronic structure and optical properties of gold clusters deposited on an α-Fe₂O₃ surface were studied by using density functional theory (DFT), with a special emphasis on the influence of Au cluster sizes.     

Crystal growth control of rod-shaped ε-Fe2O3 nanocrystals

Herein we report crystal growth control of rod-shaped ε-Fe₂O₃ nanocrystals by developing a synthesis based on the sol–gel technique using β-FeO(OH) as a seed in the presence of a barium cation. ε-Fe₂O₃ nanocrystals are obtained over a wide calcination temperature range between 800 °C and 1000 °C. A low calcination temperature (800 °C) provides an almost cubic rectangular-shaped ε-Fe₂O₃ nanocrystal with an aspect ratio of 1.4, whereas a high calcination temperature (1000 °C) provides an elongated rod-shaped ε-Fe₂O₃ nanocrystal with an aspect ratio of 3.3. Such systematic anisotropic growth of ε-Fe₂O₃ is achieved due to the wide calcination temperature in the presence of barium cations. The surface energy and the anisotropic adsorption of barium on the surface of ε-Fe₂O₃ can explain the anisotropic crystal growth of rod-shaped ε-Fe₂O₃ along the crystallographic a-axis. The present work may provide important knowledge about how to control the anisotropic crystal shape of nanomaterials.

Crystal growth control of rod-shaped ε-Fe₂O₃ nanocrystals is achieved by a synthesis based on the sol–gel technique.     

Microstructure and electrochemical properties of high performance graphene/manganese oxide hybrid electrodes

Hybrids consisting of 2D ultra-large reduced graphene oxide (RGO) sheets (∼30 μm long) and 1D α-phase manganese oxide (MnO₂) nanowires were fabricated through a versatile synthesis technique that results in electrostatic binding of the nanowires and sheets. Two different hybrid (RGO/MnO₂) compositions had remarkable features and performance: 3 : 1 MnO₂/RGO (75/25 wt%) denoted as 3H and 10 : 1 MnO₂/RGO (90/10 wt%) denoted as 10H. Characterization using spectroscopy, microscopy, and thermal analysis provided insights into the microstructure and behavior of the individual components and hybrids. Both hybrids exhibited higher specific capacitance than their individual components. 3H demonstrated excellent overall electrochemical performance with specific capacitance of 225 F g⁻¹, pseudocapacitive and electrochemical double-layer capacitance (EDLC) contributions, charge-transfer resistance <1 Ω, and 97.8% capacitive retention after 1000 cycles. These properties were better than those of 10H; this was attributed 3H''s more uniform distribution of nanowires enabling more effective electronic transport. Thermal annealing was used to produce reduced graphene oxide (RGO) that exhibited significant removal of oxygen functionality with a resulting interlayer spacing of 0.391 nm, higher D/G ratio, higher specific capacitance, and electrochemical properties representing more ideal capacitive behavior than GO. Integrating ultra-large RGO with very high surface area and MnO₂ nanowires enables chemical interactions that may improve processability into complex architectures and electrochemical performance of electrodes for applications in electronics, sensors, catalysis, and deionization.

Tuning the microstructure of ultra-large reduced graphene oxide (RGO) 2D sheets and manganese oxide (MnO₂) 1D nanowires to produce a hybrid material enabled achieving excellent electrochemical capacitive behavior for energy storage.     

A highly selective and sensitive H2S sensor at low temperatures based on Cr-doped α-Fe2O3 nanoparticles

Cr-doped α-Fe₂O₃ nanoparticles were synthesized by a low-cost and environmentally friendly hydrothermal route. Their gas sensing properties were investigated and the sensor showed high sensitivity and selectivity to H₂S gas. Different Cr doping levels from 0 to 8.0 wt% were studied, and the sensor of 4.0 wt% Cr-doped α-Fe₂O₃ showed the largest response, with a response of 213 to 50 ppm H₂S at 100 °C. The incorporation of Cr ions within α-Fe₂O₃ nanocrystals increases the specific surface area, and promotes the oxidation of H₂S and oxygen adsorption in the air. Thus, the doping of Cr into α-Fe₂O₃ nanostructures would be a promising method for designing and fabricating high performance H₂S gas sensors.

Cr-doped α-Fe₂O₃ nanoparticles were synthesized by one-step hydrothermal reaction and showed high sensitivity and selectivity to H₂S at low temperature.     

Highly efficient reduction of 4-nitrophenolate to 4-aminophenolate by Au/γ-Fe2O3@HAP magnetic composites

In this article, the catalyst Au/γ-Fe₂O₃@hydroxyapatite (Au/γ-Fe₂O₃@HAP) consisting of Au nanoparticles supported on the core–shell structure γ-Fe₂O₃@HAP was prepared through a deposition–precipitation method. The catalyst was characterized by transmission electron microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, N₂ adsorption–desorption and atomic absorption spectrometry. The as-prepared Au/γ-Fe₂O₃@HAP exhibited excellent performance for the reduction of 4-nitrophenolate (4-NP) to 4-aminophenolate (4-AP) in the presence of NaBH₄ at room temperature. Thermodynamic and kinetic data on the reduction of 4-NP to 4-AP catalyzed by the as-prepared catalyst were studied. The as-prepared catalyst could be easily separated by a magnet and recycled 6 times with over 92% conversion of 4-NP to 4-AP. In addition, the as-prepared catalyst showed excellent catalytic performance on other nitrophenolates. The TOF value of this work on the reduction of 4-NP to 4-AP was 241.3 h⁻¹. Au/γ-Fe₂O₃@HAP might have a promising potential application on the production of 4-AP and its derivatives.

In this article, the catalyst Au/γ-Fe₂O₃@hydroxyapatite (Au/γ-Fe₂O₃@HAP) consisting of Au nanoparticles supported on the core–shell structure γ-Fe₂O₃@HAP was prepared through a deposition–precipitation method.     

Enhanced photocatalytic water splitting of a SILAR deposited α-Fe2O3 film on TiO2 nanoparticles

We have investigated the effect of deposition of a α-Fe₂O₃ thin layer on a substrate of TiO₂ nanoparticles for photoelectrochemical (PEC) water splitting. The TiO₂ layer was coated on an FTO substrate using the paste of TiO₂ nanoparticles. The α-Fe₂O₃ layer was deposited on the TiO₂ thin film, using the method of Successive Ionic Layer Adsorption and Reaction (SILAR) with different cycles. Various characterizations including XRD, EDX and FE-SEM confirm the formation of α-Fe₂O₃ and TiO₂ nanoparticles on the electrode. The UV-visible absorption spectrum confirms a remarkable enhancement of the absorption of the α-Fe₂O₃/TiO₂/FTO composite relative to the bare TiO₂/FTO. In addition, the photocurrents of the composite samples are remarkably higher than the bare TiO₂/FTO. This is mainly due to the low band gap of α-Fe₂O₃, which extends the absorption spectrum of the α-Fe₂O₃/TiO₂ composite toward the visible region. In addition, the impedance spectroscopy analysis shows that the recombination rate of the charge carriers in the α-Fe₂O₃/TiO₂ is lower than that for the bare TiO₂. The best PEC performance of the α-Fe₂O₃/TiO₂ sample was achieved by the sample of 70 cycles of α-Fe₂O₃ deposition with about 7.5 times higher photocurrent relative to the bare TiO₂.

Optimization of photoelectrochemical water splitting by a composite of SILAR-deposited α-Fe₂O₃ thin film on a substrate of TiO₂ nanoparticles.     

A three-dimensional electrochemical oxidation system with α-Fe2O3/PAC as the particle electrode for ammonium nitrogen wastewater treatment

A three-dimensional particle electrode loaded with α-Fe₂O₃ on powdered activated carbon (PAC) (α-Fe₂O₃/PAC) was synthesized by the microwave method for removing ammonium nitrogen from wastewater in a three-dimensional electrode system. The α-Fe₂O₃/PAC electrode was characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effect of the added α-Fe₂O₃/PAC on the removal of ammonium nitrogen from simulated wastewater was studied by changing the cell voltage, particle dosage, and particle electrode synthesis conditions. Simulated experiments were also carried out on different pollutants under the best experimental conditions and the actual domestic sewage was tested. The results show that the optimal synthesis conditions of the particle electrode are as follows: the ratio of PAC to anhydrous FeCl₃ is 1 : 2, and the microwave power is 1000 W for 60 s. After 20 min of electrolysis at 20 V, the ammonium nitrogen removal rate can reach 95.30%.

A microwave method was used to synthesis α-Fe₂O₃/PAC 3D particle electrode rapidly which can remove NH₄⁺–N from wastewater.     

Preparation of Ag3PO4/α-Fe2O3 hybrid powders and their visible light catalytic performances

The inefficiency of conventional photocatalytic treatment for removing rhodamine B is posing potential risks to ecological environments. Here, we construct a highly efficient photocatalyst consisting of Ag₃PO₄ and α-Fe₂O₃ hybrid powders for the treatment of rhodamine B. Ag₃PO₄ nanoparticles (nanoparticles, about 50 nm) are uniformly dispersed on the surface of α-Fe₂O₃ microcrystals (hexagonal sheet, about 1.5 μm). The Ag₃PO₄-deposited uniformity on the α-Fe₂O₃ surface first increased, then decreased on increasing the hybrid ratio of Ag₃PO₄ to α-Fe₂O₃. When the hybrid ratio of Ag₃PO₄ to α-Fe₂O₃ is 1 : 2, the distribution of Ag₃PO₄ particles on the sheet α-Fe₂O₃ is more uniform with excellent Ag₃PO₄/α-Fe₂O₃ interface performance. The catalytic degradation efficiency of hybrids with the introduction of Ag₃PO₄ nanoparticles on the α-Fe₂O₃ surface reached 95%. More importantly, the hybrid material exhibits superior photocatalytic stability. Ag₃PO₄/α-Fe₂O₃ hybrids have good reusability, and the photocatalytic efficiency could still reach 72% after four reuses. The excellent photocatalytic activity of the as-prepared hybrids can be attributed to the heterostructure between Ag₃PO₄ and α-Fe₂O_3, which can effectively inhibit the photoelectron–hole recombination and broaden the visible light response range.

We construct a highly efficient photocatalyst consisting of Ag₃PO₄ and α-Fe₂O₃ hybrid powders for the treatment of rhodamine B. The catalytic degradation efficiency reached 95% after 10 min.     

A nontoxic biocompatible nanocomposite comprising black phosphorus with Au–γ-Fe2O3 nanoparticles

Black phosphorus (BP) has emerged as the latest 2D material within the post-graphene scenario, which can be used for various biomedical applications. In this study, we reported a promising nanocomposite material, which could be assembled with Au nanoparticles and γ-Fe₂O₃ nanoparticles on BP nanosheets (AIB), and studied its biocompatibility that promises to be useful for various biomedical applications. The synthesis of the Au–γ-Fe₂O₃ nanomaterial was attained through low-temperature solution synthesis and the exfoliation of BP nanosheets was performed through a liquid ultrasonication process. The individual components were then composited by ultrasonication and stirring. X-ray diffraction and transmission electron microscopic analyses confirmed the existence of Au and γ-Fe₂O₃ nanoparticles (NPs) assembled over BP nanosheets. Moreover, the surface chemical composition and valence state of the elements present in the AIB nanocomposite were evaluated with the help of an X-ray photoelectron spectroscopy study. The AIB nanocomposite exhibited excellent biocompatibility with HCT-15 cells after evaluating through WST assay. Therefore, the excellent biocompatible nature of this BP nanocomposite could be beneficial for various potential biomedical applications.

Synthesis of the Au–γ-Fe₂O₃–BP nanocomposite and its activity.     

Efficient electrocatalyst of α-Fe2O3 nanorings for oxygen evolution reaction in acidic conditions

Large-scale application of sustainable energy devices urgently requires cost-effective electrocatalysts to overcome the sluggish kinetics related to the oxygen evolution reaction (OER) under acidic conditions. Here, we first report the highly efficient electrocatalytic characteristics of α-Fe₂O₃ nanorings (NRs), which exhibits prominent OER electrocatalytic activity with lower overpotential of 1.43 V at 10 mA cm⁻² and great stability in 1 M HCl, surpassing the start-of-the art Ir/C electrocatalyst. The significantly optimized OER activity of the α-Fe₂O₃ NRs mainly attributes to the synergistic effect of the excellent electrical conductivity and a large effective active surface because of their unique nanoring structure, disordered surface, and the dynamic stability of α-Fe₂O₃ NRs in acidic conditions.

α-Fe₂O₃ NRs is obtained for OER with lower small overpotential and great stability in 1 M HCl, surpassing Ir/C electrocatalyst.     

The production of an efficient visible light photocatalyst for CO oxidation through the surface plasmonic effect of Ag nanoparticles on SiO2@α-Fe2O3 nanocomposites

A process for the photo deposition of noble Ag nanoparticles on a core–shell structure of SiO₂@α-Fe₂O₃ nanocomposite spheres was performed to produce a CO photo oxidation catalyst. The structural analyses were carried out for samples produced using different Ag metal nanoparticle weight percentages on SiO₂@α-Fe₂O₃ nanocomposite spheres by X-ray diffraction (XRD), field emission-scanning electron microscopy (FE-SEM), UV-vis spectroscopy, Raman spectroscopy and Fourier transform infrared spectroscopy (FTIR). A computational study was also performed to confirm the existence of the synergic effect of surface plasmon resonance (SPR) for different weight percentages of Ag on the SiO₂@α-Fe₂O₃ nanocomposites. The mechanism for CO oxidation on the catalyst was explored using diffuse reflectance infrared Fourier transform spectroscopy (DRFIT). The CO oxidation results for the Ag (2 wt%)-SiO₂@α-Fe₂O₃ nanocomposite spheres showed 48% higher photocatalytic activity than α-Fe₂O₃ and SiO₂@α-Fe₂O₃ at stable temperature.

We present a systematic investigation of CO oxidation and surface plasmon resonance on SiO₂@α-Fe₂O₃ nanocomposite spheres with different weight percentages of Ag nanoparticles.     

A useful preparation of ultrasmall iron oxide particles by using arc plasma deposition

Ultrasmall particles, different from the larger size nanoparticles, have recently attracted significant attention in the scientific community in nanotechnology for catalytic, electronic and optical applications; however, their magnetic properties remain unexplored due to the difficult structural analysis. A challenging issue is to develop a preparation method for iron oxide particles (IOPs) with fine size control, and to determine the dependence of magnetic properties on the morphology and crystallinity of the magnetic particles. However, synthetic approaches to obtain IOPs, regarded as one of the new fields of magnetic nanoparticles, have been significantly limited. This article reported a developed synthetic method to prepare IOPs on carbon supports using pulsed arc plasma deposition (APD) in flowing oxygen gas, which clarified the finely-controlled formation of IOPs on graphene nanosheets. Structural characterization of the IOPs revealed the formation of crystalline γ-Fe₂O₃ ultrasmall particles with oxygen deficiency. The pulsed APD method for IOPs is the first simple and convenient technique to not only prevent significant aggregation and contamination by organic compounds and avoid the need for thermal pretreatment, but also provide uniform crystalline nano-order particles.

Finely size-controlled ultrasmall iron oxide particles (IOPs) on graphene nanosheets were usefully prepared by using pulsed arc plasma deposition. The IOPs are composed of a high crystallinity single γ-Fe₂O₃ component without annealing.     

Synthesis and characterization of an α-Fe2O3/ZnTe heterostructure for photocatalytic degradation of Congo red,methyl orange and methylene blue

The leading challenge towards environmental protection is untreated textile dyes. Tailoring photocatalytic materials is one of the sustainable remediation strategies for dye treatment. Hematite (α-Fe₂O₃), due to its favorable visible light active band gap (i.e. 2.1 eV), has turned out to be a robust material of interest. However, impoverished photocatalytic efficiency of α-Fe₂O₃ is ascribable to the short life span of the charge carriers. Consequently, the former synthesized heterostructures possess low degradation efficiency. The aim of the proposed endeavor is the synthesis of a novel zinc telluride-modified hematite (α-Fe₂O₃/ZnTe) heterostructure, its characterization and demonstration of its enhanced photocatalytic response. The promising heterostructure as well as bare photocatalysts were synthesized via a hydrothermal approach. All photocatalysts were characterized by the X-ray diffraction technique (XRD), scanning electron microscopy (SEM), and electron diffraction spectroscopy (EDX). Moreover, the selectivity and activity of the photocatalyst are closely related to the alignment of its band energy levels, which were estimated by UV-Vis diffuse reflectance spectroscopy (DRS) and X-ray photoelectron spectroscopy (XPS). Nanomaterials, specifically α-Fe₂O₃ and α-Fe₂O₃/ZnTe, were used for the degradation of Congo red (97.9%), methyl orange (84%) and methylene blue (73%) under light irradiation (>200 nm) for 60 min. The results suggested that with the aforementioned optimized fabricated heterostructure, the degradation efficiency was improved in comparison to bare hematite (α-Fe₂O₃). The key rationale towards such improved photocatalytic response is the establishment of a type-II configuration in the α-Fe₂O₃/ZnTe heterostructure.

Effective generation and transportation of electron–hole pairs in the presence of light leads to efficient degradation of textile pollutants over an α-Fe₂O₃/ZnTe nanocomposite compared to the individual components.     

Novel magnetic g-C3N4/α-Fe2O3/Fe3O4 composite for the very effective visible-light-Fenton degradation of Orange II

A novel magnetic heterogeneous g-C₃N₄/α-Fe₂O₃/Fe₃O₄ catalyst was successfully synthesized through a simple hydrothermal method. The structure, morphology, and optical properties of the catalyst were characterized. The photocatalytic activity of the heterogeneous g-C₃N₄/α-Fe₂O₃/Fe₃O₄ catalyst for the photo-Fenton degradation of Orange II in the presence of H₂O₂ irradiated with visible light (λ > 420 nm) at neutral pH was evaluated. The g-C₃N₄/α-Fe₂O₃/Fe₃O₄ photocatalyst was found to be an excellent catalyst for the degradation of Orange II and offers great advantages over the traditional Fenton system (Fe(ii/iii)/H₂O₂). The results indicated that successfully combining monodispersed Fe₃O₄ nanoparticles and g-C₃N₄/α-Fe₂O₃ enhanced light harvesting, retarded photogenerated electron–hole recombination, and significantly enhanced the photocatalytic activity of the system. The g-C₃N₄/α-Fe₂O₃/Fe₃O₄ (30%) sample gave the highest degradation rate constant, 0.091 min⁻¹, which was almost 4.01 times higher than the degradation rate constant for α-Fe₂O₃ and 2.65 times higher than the degradation rate constant for g-C₃N₄/α-Fe₂O₃ under the same conditions. A reasonable mechanism for catalysis by the g-C₃N₄/α-Fe₂O₃/Fe₃O₄ composite was developed. The g-C₃N₄/α-Fe₂O₃/Fe₃O₄ composite was found to be stable and recyclable, meaning it has great potential for use as a photo-Fenton catalyst for effectively degrading organic pollutants in wastewater.

A novel magnetic heterogeneous g-C₃N₄/α-Fe₂O₃/Fe₃O₄ catalyst was firstly synthesized and exhibited very effective visible-light-Fenton degradation of Orange II at neutral pH.     

A type II heterojunction α-Fe2O3/g-C3N4 for the heterogeneous photo-Fenton degradation of phenol

The heterogeneous photo-Fenton reaction is an effective method of chemical oxidation to remove phenol in wastewater with environmental friendliness and sustainability. Herein, the composite α-Fe₂O₃/g-C₃N₄, as a catalyst of the heterogeneous photo-Fenton reaction, has been synthesized by hydrothermal-calcination method using the abundant and low-cost FeCl₃·6H₂O and g-C₃N₄ as raw materials. The influence of the annealing temperature during calcination was also investigated. The UV-Vis diffuse reflectance spectra of samples show that the composite α-Fe₂O₃/g-C₃N₄ possesses the widest light response range. Furthermore, the transient photocurrent response curves demonstrated the strongest intensity of α-Fe₂O₃/g-C₃N₄. The annealed α-Fe₂O₃/g-C₃N₄ is indicative of the highest degradation efficiency in all samples due to the improvement of the charge transfer ability caused by the tight heterojunction structure. The results of the scavenger trapping experiments show that the hydroxyl radical was the main active species in degradation. Based on experimental results, a type II heterojunction should be built in the composite α-Fe₂O₃/g-C₃N₄, driving the photoelectrons transfer and migration by internal electronic field. This work provides a facile and new method to synthesize α-Fe₂O₃/g-C₃N₄ as an effective heterogeneous photo-Fenton catalyst for environmental remediation.

Composite α-Fe₂O₃/g-C₃N₄ with type II heterojunction to degrade phenol by heterogeneous photo-Fenton reaction.     

Enhanced electrochemical performance of α-MoO3/graphene nanocomposites prepared by an in situ microwave irradiation technique for energy storage applications

Nanoparticles of α-molybdenum oxide (α-MoO₃) are directly grown on graphene sheets using a surfactant-free facile one step ultrafast in situ microwave irradiation method. The prepared α-MoO₃ and α-MoO₃/G nanocomposites are analysed by different characterization techniques to study their structural, morphological and optical properties. Transmission electron microscope images reveal the intercalation of three dimensional (3D) α-MoO₃ nanoparticles into 2D graphene sheets without any agglomeration. The electrochemical results exhibit improved performance for the α-MoO₃/G composite electrode compared to pristine α-MoO₃ owing to its structural superiority. The specific capacitance (C_s) values of the α-MoO₃/G composite and pristine α-MoO₃ are measured to be 483 and 142 F g⁻¹ respectively at a current density of 1 A g⁻¹. The α-MoO₃/G composite maintains a very strong cyclic performance after 5000 cycles. The capacitance retention of the composite electrode shows stable behavior without any degradation confirming its suitability as an enduring electrode material for high-performance supercapacitor applications.

Nanoparticles of α-molybdenum oxide (α-MoO₃) are directly grown on graphene sheets using a surfactant-free facile one step ultrafast in situ microwave irradiation method.