A comparison of stress relaxation in temporary and permanent luting cements

PurposeThe stress relaxation and compressive strength of resin, resin-modified glass ionomer, glass ionomer, polycarboxylate, and zinc oxide eugenol cements were measured to determine the characteristics of these materials after setting.MethodsA total of 19 luting cements including 12 permanent cements and 7 temporary cements were used. Cylindrical cement specimens (10 mm long and 6 mm in diameter) were obtained by chemical setting or light curing. The specimens were stored for 24–36 h in water at 37 °C and were then used for the stress relaxation and compression tests. The stress relaxation test was carried out using three constant cross-head speeds of 5, 50, and 100 mm/min. Upon reaching the preset dislocation of 0.5 mm, the cross-head movement was stopped, and the load was recorded for 60 s. Fractional stress loss at 1 s was calculated from the relaxation curves. The compressive strength and modulus were measured at a cross-head speed of 1 mm/min. Data were analyzed with the Kruskal–Wallis test and Holm's test.ResultsA zinc oxide eugenol cement [TempBOND NX] exhibited the largest fractional stress loss. A resin cement [ResiCem] showed the largest compressive strength, while a glass ionomer cement [HY-BOND GLASIONOMER CX] showed the largest compressive modulus among all tested cements (p < 0.05).ConclusionThe fractional stress loss could not be classified by the cement type. Two implant cements [Multilink Implant and IP Temp Cement] showed similar properties with permanent resin cements and temporary glass ionomer cements, respectively. Careful consideration of the choice of cement is necessary.     

The effect of temperature and ionic solutes on the fluoride release and recharge of glass-ionomer cements

ObjectiveTo determine the effect of storage temperature and the presence of sodium chloride in solution on the fluoride uptake and release of glass-ionomer cements.MethodsSeveral commercial brands were used, and stored at either room temperature (21–23 °C) or 37 °C, in KF solution at a concentration of 1000 ppm F⁻ with and without 0.9% NaCl present. Fluoride levels in the storage solutions after 24 h were measured using a fluoride-ion selective electrode. Specimens were then stored in water, and fluoride release after 24 h was determined. Studies were also carried out to determine chloride levels when specimens were stored in 0.9% NaCl, with or without 1000 ppm fluoride, again using an ion selective electrode.ResultsAll glass-ionomer specimens took up fluoride, and most of the fluoride was retained over the next 24 h when the specimens were stored in water. There was a slight variation in the amount of fluoride taken up with storage temperature and with the presence of sodium chloride. All specimens also took up chloride, with greater uptake at higher temperatures, but little or no effect when KF was also present in solution.SignificanceThe substantial retention of fluoride after 24 h in deionised water confirms previous findings and suggests that an insoluble species, possibly SrF₂, forms in situ. Chloride uptake has not been reported previously, and its significance requires further investigation. Fluoride and chloride uptake were apparently independent of each other, which suggests that the ions are taken up at different sites in the cement. This may relate to differences in the respective sizes and hydration states of F⁻ and Cl⁻ ions.     

Microhardness of resin cements in the intraradicular environment: Effects of water storage and softening treament

ObjectivesTo analyze the microhardness of four dual-cure resin cements used for cementing fiber-reinforced posts under the following conditions: after 7 days of storage in water, after additional 24 h of immersion in 75% ethanol, and after 3 months of storage in water. Hardness measurements were taken at the cervical, middle and apical thirds along the cement line.MethodsRoot canals of 40 bovine incisors were prepared for post space. Fibrekor^® glass fiber-reinforced posts (Jeneric/Pentron) of 1 mm in diameter were cemented using Panavia F 2.0 (Kuraray), Variolink (Ivoclar-Vivadent), Rely X Unicem (3M ESPE) or Duolink (Bisco) (N = 10). After 7 days of water storage at 37 °C, half the sample (N = 5) was longitudinally sectioned and the initial microhardness measured along the cement line from cervical to apex. These same samples were further immersed in 75% ethanol for 24 h and reassessed. The remaining half (N = 5) was kept unsectioned in deionized water at 37 °C for 3 months, followed by sectioning and measuring. Data were analyzed by a series of two-way ANOVA and Tukey tests at α = 5%.ResultsStatistically significant differences were identified among the cements, thirds and conditions. Significant interactions were also observed between cements and thirds and between cements and conditions. Panavia F exhibited significantly higher initial microhardness than the other three cements, which showed no statistical difference among themselves. Variolink and Duolink showed significantly higher microhardness values in the cervical third, without significant difference among the thirds for the other cements. Immersion in ethanol significantly reduced the hardness values for all cements, regardless of the thirds. Storage in water for 3 months had no influence on the hardness of most of the cements, with the exception of Unicem that showed a significant increase in the hardness values after this period.SignificanceResults showed heterogeneity in the microhardness of the cements inside the canal. All cements presented some degree of softening after ethanol treatment, which suggests instability of the polymer. The quality of curing of resin cements in the root canal environment seems unpredictable and highly material dependent.     

Influence of composition on setting kinetics of new injectable and/or fast setting tricalcium silicate cements

ObjectivesNew commercial tricalcium silicate based cements were elaborated to improve handling properties and setting time. The goals of the present work were: (i) to determine the composition of the new injectable and/or fast setting calcium silicate based cements, and (ii) to investigate the impact of the differences in composition on their setting kinetics.MethodsThe materials considered were Angelus MTA™, Biodentine™, MM-MTA™, MTA-Caps™, and ProRoot MTA™ as control.Elemental composition of materials was studied by Inductively Coupled Plasma-Atomic Emission Spectroscopy and X-ray Energy Dispersive analysis, whereas phases in presence were analyzed by Micro-Raman spectroscopy and X-ray Diffraction analysis and cement surface by Scanning Electron Microscope. Setting kinetics was evaluated using rheometry.ResultsElemental analysis revealed, for all cements, the presence of three major components: calcium, silicon and oxygen. Chlorine was detected in MM-MTA, MTA-Caps and Biodentine. Different radio-opacifiers were identified: bismuth oxide in ProRoot MTA, Angelus MTA and MM-MTA, zirconium oxide in Biodentine and calcium tungstate (CaWO₄) in MTA-Caps. All cements were composed of di- and tri-calcium silicate, except Biodentine for which only the latter was detected. Major differences in setting kinetics were observed: a modulus of 8 × 10⁸ Pa is reached after 12 min for Biodentine, 150 min for MM-MTA, 230 min for Angelus MTA and 320 min for ProRoot MTA. The maximum modulus reached by MTA-Caps was 7 × 10⁸ Pa after 150 min.SignificanceEven if these cements possess some common compounds, major differences in their composition were observed between them, which directly influence their setting kinetics.     

Randomized clinical trial on effectiveness of silver diamine fluoride and glass ionomer in arresting dentine caries in preschool children

ObjectiveTo compare the effectiveness of annual topical application of silver diamine fluoride (SDF) solution, semi-annual topical application of SDF solution, and annual application of a flowable high fluoride-releasing glass ionomer in arresting active dentine caries in primary teeth.MethodsA total of 212 children, aged 3–4 years, were randomly allocated to one of three groups for treatment of carious dentine cavities in their primary teeth: Gp1-annual application of SDF, Gp2-semi-annual application of SDF, and Gp3-annual application of glass ionomer. Follow-up examinations were carried out every six months to assess whether the treated caries lesions had become arrested.ResultsAfter 24 months, 181 (85%) children remained in the study. The caries arrest rates were 79%, 91% and 82% for Gp1, Gp2 and Gp3, respectively (p = 0.007). In the logistic regression model using GEE to adjust for clustering effect, higher caries arrest rates were found in lesions treated in Gp2 (OR = 2.98, p = 0.007), those in anterior teeth (OR = 5.55, p < 0.001), and those in buccal/lingual smooth surfaces (OR = 15.6, p = 0.004).ConclusionAnnual application of either SDF solution or high fluoride-releasing glass ionomer can arrest active dentine caries. Increasing the frequency of application to every 6 months can increase the caries arrest rate of SDF application.Clinical significanceArrest of active dentine caries in primary teeth by topical application of SDF solution can be enhanced by increasing the frequency of application from annually to every 6 months, whereas annual paint-on of a flowable glass ionomer can also arrest active dentine caries and may provide a more aesthetic outcome.     

Mechanical properties of new self-adhesive resin-based cement

PurposeThe aim of this study was to compare the bonding strength, flexural strength, elastic modulus, water absorption and the expansion after water storage of new self-adhesive resin cements to commercially available dental cements.MethodsTwo types (hand-mix and auto-mix) of new self-adhesive resin cements (SAC-H and SAC-A, Kuraray Medical), one conventional resin cement (Panavia F2.0), three self-adhesive resin cements (Relyx Unicem, Maxcem and G-Cem), and two resin-modified glass-ionomer cements (Fuji Luting S and Vitremer) were used. Shear bond strengths, flexural strengths and elastic moduli (ISO 4049), water absorption (ISO 4049), and the expansion rate after water storage were investigated.ResultsBoth SAC-H and SAC-A provided adhesion to enamel and dentin, and had the same bond strength to gold alloy and zirconia as conventional resin cements. SAC-H and SAC-A had greater flexural strengths (86.4–93.5 MPa) than commercial self-adhesive resin cements or glass-ionomer cements. The elastic moduli of self-adhesive and glass-ionomer cements were 5.2–7.4 GPa and 2.3–3.4 GPa, respectively. The water absorption of SAC-H and SAC-A (26.3–27.7 μg/mm³) were significantly lower than commercial self-adhesive resin cements. SAC-H and SAC-A showed significantly lower expansion rates (0.17–0.26%) than commercial self-adhesive cements and glass-ionomer cements after 4 weeks water storage.ConclusionsIt is suggested that the new self-adhesive resin cements exhibited a favorable bonding capability and mechanical properties.     

Effect of pulpal pressure on the microtensile bond strength of luting resin cements to human dentin

ObjectivesThe objectives of this study were to examine the effect of pulpal pressure on the microtensile bond strength (mTBS) of luting resin cements to human dentin and the permeability of dentin surfaces pre-treated with an adhesive and a self-etching primer.MethodsCylindrical composite blocks were luted with resin cements (RelyX ARC, 3M ESPE: ARC; Panavia F, Kuraray Medical Inc.: PF; RelyX Unicem, 3M ESPE: UN) in the absence or presence of simulated pulpal pressure. The application of Adper Single Bond 2 (3M ESPE) and ED primer 2.0 (Kuraray) was performed under 0 cm H₂O. After each resin cement was applied, the pulpal pressure group was subjected to 20 cm H₂O of hydrostatic pressure for 10 min during the initial setting period. Testing for mTBS was performed on 0.9 mm × 0.9 mm sectioned beams after 24 h water-storage. Scanning electron microscopy was performed to investigate the fractured surfaces after mTBS testing and additional dentin surfaces that were treated by an etchant, ED primer 2.0 and UN. Fluid permeability was measured on dentin surfaces that were applied with Adper Single Bond 2 and ED primer 2.0.ResultsApplication of pulpal pressure reduced mTBS significantly in groups ARC and PF. Porous bonding interfaces due to water permeability through the cured adhesive were observed on fractured surfaces. Dentin surfaces that were applied with the adhesive and the primer were more permeable than smear layer-covered dentin. The mTBS of UN was significantly lower than ARC and PF regardless of the absence/presence of pulpal pressure.SignificanceFluid permeation during the initial setting period deteriorated the bonding quality of resin cements.     

Effect of immersion time of restorative glass ionomer cements and immersion duration in calcium chloride solution on surface hardness

ObjectivesThe objective of this study was to evaluate the effect of immersion time of restorative glass ionomer cements (GICs) and immersion duration in calcium chloride (CaCl₂) solution on the surface hardness.MethodsTwo high-viscosity GICs, Fuji IX GP and GlasIonomer FX-II, were selected. Forty-eight specimens were randomly divided into two groups. Sixty minutes after being mixed, half of them were immersed in a 42.7 wt% CaCl₂ solution for 10, 30, or 60 min (Group 1); the remaining specimens were immersed after an additional 1-week of storage (Group 2). The surface hardness of the specimens was measured and analyzed with two-way ANOVA and the Tukey HSD test (α = 0.05). The surface compositions were examined using energy-dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy.ResultsThe surface hardness of Group 1 significantly increased as the immersion duration in CaCl₂ increased; that of Group 2 significantly increased only after 60-minute CaCl₂ immersion. After CaCl₂ immersion, the amounts of Ca increased as the immersion duration increased. The surface hardness after CaCl₂ immersion significantly correlated with the amount of Ca in Group 1, but not in Group 2. The binding energy of the Ca2p peak was similar to that of calcium polyalkenoate. These findings indicated that the Ca ions from the CaCl₂ solution created chemical bonds with the carboxylic acid groups in the cement matrix.SignificanceImmersion of GICs in CaCl₂ solution at the early stage of setting was considered to enhance the formation of the polyacid salt matrix; as a result, the surface hardness increased.     

The effect of excitation laser power in Raman spectroscopic measurements of the degree of conversion of resin composites

ObjectivesTo evaluate the effect of excitation laser power in Raman spectrometry by comparing the spectra and the degree of conversion (DC) values obtained using excitation powers between 300 and 1000 mW.MethodsFive commercial and three experimental resin composites were light cured at 1200 mW/cm² for 10–20 s from a commercial blue-violet LED dental curing unit. Raman spectra were collected from composite specimens within 9 min after light-curing. The excitation laser (1064 nm) was focused on the spot of 0.4 mm in diameter. The following powers were used for specimen excitation (mW): 300, 400, 600, 800, and 1000. From Raman spectra, the DC values were calculated and compared among different laser powers. Also, vector-normalized Raman spectra collected using the lowest excitation power (300 mW) were compared to those collected using the maximum excitation power (1000 mW).ResultsVarying the excitation laser power between 300 and 1000 mW resulted in statistically significant differences in both the DC values and the intensity of particular spectral features. The effect of varying laser power on Raman spectra and obtained DC values was material-dependent. The DC values measured within an individual material using different laser powers varied between 3.2 and 7.2% (absolute DC difference). The spectral bands affected by variations in laser power were assigned to symmetric and asymmetric stretching of −CH₂ (2900-3100 cm⁻¹), symmetric stretching of aliphatic CC (1640 cm⁻¹) and scissoring of C–H (1458 cm⁻¹).SignificanceThe DC can be artificially elevated through increasing excitation laser power. This effect should be considered in Raman spectroscopic evaluations of DC in specimens during ongoing post-cure polymerization.     

An evaluation of microleakage of various glass ionomer based restorative materials in deciduous and permanent teeth: An in vitro study

AimTo evaluate the microleakage of recently available glass ionomer based restorative materials (GC Fuji IX GP, GC Fuji VII, and Dyract) and compare their microleakage with the previously existing glass ionomer restorative materials (GC Fuji II LC) in primary and permanent teeth.MethodOne hundred and fifty (75 + 75) non-carious deciduous and permanent teeth were restored with glass ionomer based restorative materials after making class I cavities. Samples were subjected to thermocycling after storing in distilled water for 24 h. Two coats of nail polish were applied 1 mm short of restorative margins and samples sectioned buccolingually after storing in methylene blue dye for 24 h. Microleakage was assessed using stereomicroscope.ResultSignificant differences (P < 0.05) were found when inter group comparisons were done. Except when GC Fuji VII (Group III) was compared with GC Fuji II LC (Group II) and Dyract (Group IV), non-significant differences (P > 0.05) were observed. It was found that there was no statistically significant difference when the means of microleakage of primary teeth were compared with those of permanent teeth.ConclusionsGC Fuji IX GP showed maximum microleakage and GC Fuji VII showed least microleakage.     

Self-adhesive resin cement versus zinc phosphate luting material: A prospective clinical trial begun 2003

ObjectivesThe literature demonstrates that conventional luting of metal-based restorations using zinc phosphate cements is clinically successful over 20 years. This study compared the clinical outcomes of metal-based fixed partial dentures luted conventionally with zinc phosphate and self-adhesive resin cement.MethodsForty-nine patients (mean age 54 ± 13 years) received 49 metal-based fixed partial dentures randomly luted using zinc phosphate (Richter & Hoffmann, Berlin, Germany) or self-adhesive resin cement (RelyX Unicem Aplicap, 3M ESPE, Germany) at the University Medical Center Regensburg. The core build-up material was highly viscous glass ionomer; the finishing line was in dentin. The study included 42 posterior, 5 anterior crowns and two onlays. Forty-seven restorations were made of precious alloys, 2 of non-precious alloys. The restorations were clinically examined every year. The clinical performance was checked for plaque (0–5; PI, Quigley-Hein), bleeding (0–4; PBI; Mühlemann) and attachment scores. The examination included pulp vitality and percussion tests.StatisticsMeans of scores, standard deviation, cumulative survival and complication rates were calculated using life tables.ResultsThe mean observation time was 3.16 ± 0.6 years (min: 2.0; max: 4.5 years). During that time no restoration was lost, no recementation became necessary. One endodontic treatment was performed in the self-adhesive composite group after 2.9 years. At study end bleeding (1.44 RelyX Unicem vs. 1.25 zinc phosphate) and plaque (1.64 RelyX Unicem vs. 1.0 zinc phosphate) scores showed no statistically significant difference.SignificanceThe self-adhesive resin cement performed clinically as well and can be used as easily as zinc phosphate cement to retain metal-based restorations over a 38-month observation period.     

Curing efficiency of four self-etching,self-adhesive resin cements

ObjectivesTo evaluate the degree of cure (%DC) of four self-etching, self-adhesive resin cements, and one conventional resin cement, in their self- and dual-curing mode.MethodsThe self-etching, self-adhesive resin cements studied were RelyX? Unicem (3M? ESPE? AG), Maxcem? (Kerr Corporation), Biscem? (Bisco, Inc.) and Multilink^® Sprint (Ivoclar Vivadent^® AG) and the classic resin cement was Multilink^® Automix (Ivoclar Vivadent^® AG). Twelve specimens of each material (1.8 mm × 4 mm × 4 mm) were prepared in room temperature (23 ± 1) °C following the manufacturers’ instructions. Six of them were treated as dual-cured, thus irradiated for 20 s with a halogen light curing unit and left undisturbed for 5 min. The other six were treated as self-cured and were not irradiated, but left in dark and dry conditions for 10 min. The assessment of the %DC was made using micro-ATR FTIR spectrometry.ResultsThe %DC in their self-curing mode was very low (10.82–24.93%), with Multilink Sprint exhibiting the highest values among the five. In the dual-curing mode the values obtained were also low (26.40–41.52%), with the exception of Multilink Automix (61.36%). Maxcem was found to have the lowest DC.SignificanceThe low %DC found raises questions as to whether these materials can be successfully used in clinical applications, where light attenuation takes place. Increased irradiation times could potentially lead to higher %DC, in applications where light is not completely blocked by the overlying restoration.     

Development and characterisation of dental composites containing anisotropic fluorapatite bundles and rods

ObjectivesTo develop dental composites incorporating fluorapatite (FA) crystals as a secondary filler and to characterise degree of conversion, key mechanical properties and fluoride release.MethodsFA rod-like crystals and bundles were hydrothermally synthesised and characterised by scanning electron microscopy/energy dispersive X-ray spectroscopy (SEM/EDS), X-ray diffraction (XRD) and ¹⁹F MAS-NMR. Composites were formulated containing BisGMA/TEGDMA/BisEMA and barium-aluminium-silicate glass (0FA). FA crystals were incorporated at 10 (10FA), 20 (20FA), 30 (30FA) and 40 wt% (40FA) maintaining a filler content of 80 wt% (63–67 vol%). Degree of conversion (DC), flexural strength (FS), flexural modulus (FM), fracture toughness (K_1C), Vickers hardness (HV) and 2-body wear were measured. Fluoride release was measured in neutral and acidic buffers.ResultsXRD and ¹⁹F MAS-NMR confirmed that only FA was formed, whilst SEM revealed the presence of single rods and bundles of nano-rods. DC ranged between 56–60% (p > 0.05). FA composites showed lower FM and lower FS (p < 0.05), but comparable wear resistance and HV (p > 0.05) to 0FA. 30FA and 40FA showed similar K_1C to 0FA (p > 0.05), with SEM showing evidence of toughening mechanisms, whereas 10FA and 20FA showed lower K_1C (p < 0.05). FA containing composites released fluoride that was proportional to the amount of FA incorporated (p < 0.05) but only under acidic conditions.SignificanceThe addition of FA to the experimental composites reduced strength and stiffness but not the DC, hardness or wear rate. 30FA and 40FA had a higher K_1C compared to other FA groups. Fluoride release occurred under an accelerated acidic regime, suggesting potential as a bioactive ‘smart’ composite.     

Adhesive class I restorations in sound molar teeth incorporating combined resin-composite and glass ionomer materials: CAD-FE modeling and analysis

ObjectivesTo investigate the influence of different resin composite and glass ionomer cement material combinations in a “bi-layer” versus a “single-layer” adhesive technique for class I cavity restorations in molars using numerical finite element analysis (FEA).Materials and MethodsThree virtual restored lower molar models with class I cavities 4 mm deep were created from a sound molar CAD model. A combination of an adhesive and flowable composite with bulk fill composite (model A), of a glass ionomer cement with bulk fill composite (model B) and of an adhesive with bulk fill composite (model C), were considered. Starting from CAD models, 3D-finite element (FE) models were created and analyzed. Solid food was modeled on the occlusal surface and slide-type contact elements were used between tooth surface and food. Polymerization shrinkage was simulated for the composite materials. Physiological masticatory loads were applied to these systems combined with shrinkage. Static linear analyses were carried out. The maximum normal stress criterion was adopted as a measure of potential damage.ResultsAll models exhibited high stresses principally located along the tooth tissues–restoration interfaces. All models showed a similar stress trend along enamel–restoration interface, where stresses up to 22 MPa and 19 MPa was recorded in the enamel and restoration, respectively. A and C models showed a similar stress trend along the dentin-restoration interface with a lower stress level in model A, where stresses up to 11.5 MPa and 7.5 MPa were recorded in the dentin and restoration, respectively, whereas stresses of 17 MPa and 9 MPa were detected for model C. In contrast to A and C models, the model B showed a reduced stress level in dentin, in the lower restoration layer and no stress on the cavity floor.SignificanceFE analysis supported the positive effect of a “bi-layer” restorative technique in a 4 mm deep class I cavities in lower molars versus “single-layer” bulk fill composite technique.     

Effect of chlorhexidine application on long-term shear bond strength of resin cements to dentin

PurposeThe purpose of this study was to investigate the effect of chlorhexidine [CH] on dentin bond strength of three resin cements after 1 year of water storage.MethodsA flat middle dentin surface was prepared on 120 extracted premolars. The teeth were randomly divided into 6 groups of 20 specimens each according to the resin cement used: Panavia F2.0, Variolink II, and RelyX Unicem, with or without CH application. After cementation of an indirect composite rod [Z250], one subgroup [n = 10] was tested after 24 h in water at 37 °C and the other subgroup [n = 10] was tested after 1 year storage in water plus thermocycling. A shear bond strength [SBS] test was performed. The data [in MPa] were analyzed with ANOVA and Tukey tests [P < 0.05].ResultsThree-way ANOVA [resin cement, CH and time] indicated that Variolink II had the highest strength [16.65 ± 3.60] and RelyX Unicem had the lowest strength [9.30 ± 4.07]. Chlorhexidine application increased SBS [13.31 ± 4.61] compared to samples without CH [12.16 ± 5.04] [P = 0.04]. Initial SBS [15.63 ± 4.37] was significantly higher than after 1 year of storage [9.85 ± 3.36] [P < 0.001]. Separate two-way ANOVA for 24-h and 1-year data showed that cement had a significant effect but CH and its interaction had no significant effect at 24 h, whereas at 1 year the two factors and their interaction differed significantly [P ≤ 0.001].ConclusionsChlorhexidine 2% can diminish the loss of bonding effectiveness over time associated to etch-and-rinse and self-etch cements, although it appears not have any effect on self-adhesive cement.     

Zirconia toughened mica glass ceramics for dental restorations: Wear,thermal, optical and cytocompatibility properties

BackgroundIn an effort to design novel zirconia reinforced mica glass ceramics for dental restorations, clinically relevant properties such as wear, coefficient of thermal expansion, optical transmittance, and cytocompatibility with human gingival fibroblast cell lines were investigated in the present study.Materials & MethodsMicrostructure analysis of two body wear of heat treated mica glass ceramic ceramics (47.2 SiO₂–16.7 Al₂O₃–9.5 K₂O–14.5 MgO–8.5 B₂O₃–6.3 F wt.%) reinforced with 20 wt.% YSZ, were evaluated against a steatite antagonist in a chewing simulator following Willytec Munich method. In addition, Coefficient of thermal expansion (CTE), total transmittance, scattering coefficient and cytocompatibility on human gingival fibroblast cell lines were performed and compared to the commercially available dental ceramic systems.ResultsThe experimental mica glass ceramic demonstrate micro-ploughing, pull out and debris formation along the cutting surface, indicating abrasive wear mechanism. Thermal expansion of mica glass ceramic composite was recorded as 5 × 10⁻⁶/°C, which is lower than the thermal expansion of commercially available core and veneering ceramics. Further, significant differences of transmittance and scattering coefficient of mica glass ceramics with 20 wt.% YSZ with commercial dental ceramics was found and extensive fibroblast cell spreading with filopodial extension, cell-to-cell bridges and proliferation with human gingival fibroblast cell lines.ConclusionWith acceptable cytocompatibility with human gingival fibroblast cells and better wear properties with respect to commercial IPS emax Press, the mica glass ceramic composites (47.2 SiO₂–16.7Al₂O₃–9.5 K₂O–14.5 MgO–8.5 B₂O₃–6.3 F wt.%) with 20 wt.% YSZ have the potential for dental restorative applications as machinable veneering ceramics.     

Water sorption and solubility of core build-up materials

ObjectivesTo investigate the variation in water sorption and solubility across a range of different core build-up materials.MethodsFive materials were tested, four of which are resin-based materials (Grandio Core, Core.X Flow, Bright Flow Core, Speedee) and one resin-modified glass ionomer (Fuji II LC). All specimens (n = 10) were immersed in 10 ml distilled water in individual glass containers and weighed at one week, 14 and 28 days. After a total immersion time of 28 days, 7 specimens were dried to a constant mass, in a desiccator for 28 days. Three samples of each material were not dried, but were left in distilled water for 1 year, to determine the long-term water sorption properties. Specimens were weighed at monthly intervals until 6 months and then at the 9th and 12th months. Each specimen was measured using a digital electronic caliper (Mitutoyo Corporation, Japan).ResultsAfter 28 days immersion, the change in water sorption and solubility of the materials ranged from 12.9 to 67.1 μg/mm³ (P < 0.001) and 0.9–6.4 μg/mm³ respectively (P < 0.001). Except for Fuji II LC, an independent T-test showed significantly higher water sorption and solubility for the other materials after 1-year total immersion in water compared to 1 month (P < 0.05). Using repeated measures ANOVA, all materials showed mass changes over time (1 month) (P < 0.001).SignificanceGrandio Core had the lowest water sorption and solubility among the tested materials. According to the ISO 4049 standards, all the tested materials showed acceptable water sorption and solubility, apart from the water sorption behavior of Fuji II LC.     

Glass ionomer cements: Effect of strontium substitution on esthetics,radiopacity and fluoride release

Objective

SrO and SrF₂ are widely used to replace CaO and CaF₂ in ionomer glasses to produce radiopaque glass ionomer cements (GIC). The purpose of this study was to evaluate the effects of this substitution on release of ions from GIC as well as its effect on esthetics (translucency) and radiopacity.

Materials and methods

Cements were produced from ionomer glasses with varying content of Sr, Ca and F. The cements were stored in dilute acetic acid (pH 4.0) for up to 7 days at 37 °C. Thereafter, the cements were removed and the solution was tested for F⁻, Sr²⁺, Ca²⁺, and Al³⁺ release. Radiopacity and translucency were measured according to BS EN ISO 9917-1:2003.

Results

Ion release was linear to t^1/2 suggesting that this is a diffusion controlled mechanism rather than dissolution. The fluoride release from the cements is enhanced where some or all calcium is replaced by strontium. Radiopacity shows a strong linear correlation with Sr content. All cements were more opaque than the C_0.70 0.55 standard but less opaque than the C_0.70 0.90 standard which is the limit for the ISO requirement for acceptance.

Significance

This study shows that the replacement of calcium by strontium in a glass ionomer glass produces the expected increase in radiopacity of the cement without adverse effects on visual properties of the cement. The fluoride release from the cements is enhanced where some or all calcium is replaced by strontium.     

Sodium fluoride effect on erosion–abrasion under hyposalivatory simulating conditions

ObjectivesTo investigate the effect of fluoride (0, 275 and 1250 ppm F; NaF) in combination with normal and low salivary flow rates on enamel surface loss and fluoride uptake using an erosion–remineralization–abrasion cycling model.DesignEnamel specimens were randomly assigned to 6 experimental groups (n = 8). Specimens were individually placed in custom made devices, creating a sealed chamber on the enamel surface, connected to a peristaltic pump. Citric acid was injected into the chamber for 2 min followed by artificial saliva at 0.5 (normal flow) or 0.05 (low flow) ml/min, for 60 min. This cycle was repeated 4×/day, for 5 days. Toothbrushing with abrasive suspensions containing fluoride was performed for 2 min (15 s of actual brushing) 2×/day. Surface loss was measured by optical profilometry. KOH-soluble fluoride and enamel fluoride uptake were determined after the cycling phase. Data were analysed by two-way ANOVA.ResultsNo significant interactions between fluoride concentration and salivary flow were observed for any tested variable. Low caused more surface loss than normal flow rate (p < 0.01). At both flow rates, surface loss for 0 was higher than for 275, which did not differ from 1250 ppm F. KOH-soluble and structurally-bound enamel fluoride uptake were significantly different between fluoride concentrations with 1250 > 275 > 0 ppm F (p < 0.01).ConclusionsSodium fluoride reduced enamel erosion/abrasion, although no additional protection was provided by the higher concentration. Higher erosion progression was observed in low salivary flow rates. Fluoride was not able to compensate for the differences in surface loss between flow rates.     

Influence of surface treatments and resin cement selection on bonding to densely-sintered zirconium-oxide ceramic

ObjectivesTo evaluate the effect of surface conditioning on the microtensile bond strength of zirconium-oxide ceramic to dual-cured resin cements.MethodsEighteen cylinder-shaped zirconium-oxide ceramic blocks (Cercon^® Zirconia, Dentsply) were treated as follows: (1) Sandblasting with 125 μm aluminum-oxide (Al₂O₃) particles; (2) tribochemical silica coating using 50 μm Al₂O₃ particles modified by silica; (3) no treatment. Each ceramic cylinder was duplicated in composite resin (Tetric Evo Ceram, Ivoclar-Vivadent) using a silicon mold. Composite cylinders were bonded to conditioned ceramics using: (1) Calibra (Densply Caulk); (2) Clearfil Esthetic Cement (Kuraray); (3) Rely × Unicem (3 M ESPE). After 24 h bonded specimens were cut into microtensile sticks that were loaded in tension until failure. Data were analyzed using two-way ANOVA and Student–Newman–Keuls test for multiple comparisons (p < 0.05). Failure mode was recorded and the interfacial morphology of debonded specimens was observed using a scanning electron microscope (SEM). Surface topography and ceramic average surface roughness were analyzed under an atomic force microscope (AFM).ResultsSignificant changes in zirconia surface roughness occurred after sandblasting (p < 0.001). Bond strength of Clearfil cement to zirconia was significantly higher than that of Rely × Unicem and Calibra, regardless of the surface treatment (p < 0.001). When using Calibra, premature failures occurred in non-treated and silica coated zirconia surfaces.SignificanceThe phosphate monomer-containing luting system (Clearfil Esthetic Cement) is recommended to bond zirconia ceramics and surface treatments are not necessary.