Comparison of photopolymerizable thiol-ene PEG and acrylate-based PEG hydrogels for cartilage development

When designing hydrogels for tissue regeneration, differences in polymerization mechanism and network structure have the potential to impact cellular behavior. Poly(ethylene glycol) hydrogels were formed by free-radical photopolymerization of acrylates (chain-growth) or thiol-norbornenes (step-growth) to investigate the impact of hydrogel system (polymerization mechanism and network structure) on the development of engineered tissue. Bovine chondrocytes were encapsulated in hydrogels and cultured under free swelling or dynamic compressive loading. In the acrylate system immediately after encapsulation chondrocytes exhibited high levels of intracellular ROS concomitant with a reduction in hydrogel compressive modulus and higher variability in cell deformation upon compressive strain; findings that were not observed in the thiol-norbornene system. Long-term the quantity of sulfated glycosaminoglycans and total collagen was greater in the acrylate system, but the quality resembled that of hypertrophic cartilage with positive staining for aggrecan, collagens I, II, and X and collagen catabolism. The thiol-norbornene system led to hyaline-like cartilage production especially under mechanical loading with positive staining for aggrecan and collagen II and minimal staining for collagens I and X and collagen catabolism. Findings from this study confirm that the polymerization mechanism and network structure have long-term effects on the quality of engineered cartilage, especially under mechanical loading.     

A biomimetic extracellular matrix for cartilage tissue engineering centered on photocurable gelatin,hyaluronic acid and chondroitin sulfate

The development of hydrogels tailored for cartilage tissue engineering has been a research and clinical goal for over a decade. Directing cells towards a chondrogenic phenotype and promoting new matrix formation are significant challenges that must be overcome for the successful application of hydrogels in cartilage tissue therapies. Gelatin–methacrylamide (Gel-MA) hydrogels have shown promise for the repair of some tissues, but have not been extensively investigated for cartilage tissue engineering. We encapsulated human chondrocytes in Gel-MA-based hydrogels, and show that with the incorporation of small quantities of photocrosslinkable hyaluronic acid methacrylate (HA-MA), and to a lesser extent chondroitin sulfate methacrylate (CS-MA), chondrogenesis and mechanical properties can be enhanced. The addition of HA-MA to Gel-MA constructs resulted in more rounded cell morphologies, enhanced chondrogenesis as assessed by gene expression and immunofluorescence, and increased quantity and distribution of the newly synthesized extracellular matrix (ECM) throughout the construct. Consequently, while the compressive moduli of control Gel-MA constructs increased by 26 kPa after 8 weeks culture, constructs with HA-MA and CS-MA increased by 114 kPa. The enhanced chondrogenic differentiation, distribution of ECM, and improved mechanical properties make these materials potential candidates for cartilage tissue engineering applications.     

Injectable glycopolypeptide hydrogels as biomimetic scaffolds for cartilage tissue engineering

Glycopolypeptides are an emerging class of bioinspired polymers that mimic naturally occurring glycopeptides or glycoproteins, and therefore are expected to exhibit great potential for biomedical applications. In this study, a glycopolypeptide was synthesized by conjugation of poly(γ-propargyl-l-glutamate) (PPLG) with azido-modified mannose and 3-(4-hydroxyphenyl) propanamide (HPPA), via click chemistry. Injectable hydrogels based on the glycopolypeptide were developed through enzymatic crosslinking reaction in the presence of horseradish peroxidase (HRP) and hydrogen peroxide (H₂O₂). The physicochemical properties of the hydrogels, such as gelation time, storage modulus, swelling and degradation time, could be controlled by varying the concentrations of HRP and H₂O₂. The glycopolypetide copolymer as well as the extracts of the glycopolypetide hydrogels displayed good cytocompatibility in vitro. After subcutaneous injection into rats, the glycopolypeptide hydrogels were rapidly formed in situ, and exhibited acceptable biocompatibility accompanying the degradation of the hydrogels in vivo. The rabbit chondrocytes inside the glycopolypeptide hydrogels showed spherical morphology with high viability during the incubation period of 3 weeks in vitro, and exhibited a higher proliferation rate than within the hydrogel counterparts of PPLG grafted with 2-(2-(2-methoxyethoxy)ethoxy)ethane (MEO₃) and HPPA. Biochemical analysis demonstrated that the production of glycosaminoglycans (GAG) and type II collagen were significantly enhanced after incubation for 2 and 3 weeks in vitro. Moreover, the chondrocyte-containing glycopolypeptide hydrogels in subcutaneous model of nude mice maintained chondrocyte phenotype and produced the cartilaginous specific matrix. These results indicated that the biomimetic glycopolypeptide-based hydrogels hold potential as three-dimensional scaffolds for cartilage tissue engineering.     

Characterization of sequential collagen-poly(ethylene glycol) diacrylate interpenetrating networks and initial assessment of their potential for vascular tissue engineering

Collagen hydrogels have been widely investigated as scaffolds for vascular tissue engineering due in part to the capacity of collagen to promote robust cell adhesion and elongation. However, collagen hydrogels display relatively low stiffness and strength, are thrombogenic, and are highly susceptible to cell-mediated contraction. In the current work, we develop and characterize a sequentially-formed interpenetrating network (IPN) that retains the benefits of collagen, but which displays enhanced mechanical stiffness and strength, improved thromboresistance, high physical stability and resistance to contraction. In this strategy, we first form a collagen hydrogel, infuse this hydrogel with poly(ethylene glycol) diacrylate (PEGDA), and subsequently crosslink the PEGDA by exposure to longwave UV light. These collagen-PEGDA IPNs allow for cell encapsulation during the fabrication process with greater than 90% cell viability via inclusion of cells within the collagen hydrogel precursor solution. Furthermore, the degree of cell spreading within the IPNs can be tuned from rounded to fully elongated by varying the time delay between the formation of the cell-laden collagen hydrogel and the formation of the PEGDA network. We also demonstrate that these collagen-PEGDA IPNs are able to support the initial stages of smooth muscle cell lineage progression by elongated human mesenchymal stems cells.     

胶原水凝胶在软骨与骨组织工程中的研究进展

胶原水凝胶因其具有优良的生物相容性、生物力学性能，在软骨与骨组织工程、生物填充材料、创伤修复、药物缓释和细胞培养等医学领域获得广泛的关注和应用。本文重点介绍了胶原水凝胶在软骨与骨组织工程方面的研究进展，详细阐述了胶原水凝胶的性能、交联方法和类型，并对胶原水凝胶在软骨与骨组织工程中的研究现状进行了讨论，对其应用前景进行了展望。     

Differential effect of hypoxia on human mesenchymal stem cell chondrogenesis and hypertrophy in hyaluronic acid hydrogels

Photocrosslinked hyaluronic acid (HA) hydrogels provide a conducive 3-D environment that supports the chondrogenesis of human mesenchymal stem cells (hMSCs). The HA macromer concentration in the hydrogels has a significant impact on the chondrogenesis of the encapsulated MSCs due to changes in the physical properties of the hydrogels. Meanwhile, hypoxia has been shown to promote MSC chondrogenesis and suppress subsequent hypertrophy. This study investigates the combinatorial effect of tuning HA macromer concentration (1.5–5% w/v) and hypoxia on MSC chondrogenesis and hypertrophy. To decouple the effect of HA concentration from that of crosslinking density, the HA hydrogel crosslinking density was adjusted by varying the extent of the reaction through the light exposure time while keeping the HA concentration constant (5% w/v at 5 or 15 min). It was found that hypoxia had no significant effect on the chondrogenesis and cartilaginous matrix synthesis of hMSCs under all hydrogel conditions. In contrast, the hypoxia-mediated positive or negative regulation of hMSC hypertrophy in HA hydrogels is dependent on the HA concentration but independent of the crosslinking density. Specifically, hypoxia significantly suppressed hMSC hypertrophy and neocartilage calcification in low HA concentration hydrogels, whereas hypoxia substantially enhanced hMSC hypertrophy, leading to elevated tissue calcification in high HA concentration hydrogels irrespective of their crosslinking density. In addition, at a constant high HA concentration, increasing hydrogel crosslinking density promoted hMSC hypertrophy and matrix calcification. To conclude, the findings from this study demonstrate that the effect of hypoxia on hMSC chondrogenesis and hypertrophy is differentially influenced by the encapsulating HA hydrogel properties.     

Interpenetrating networks based on gelatin methacrylamide and PEG formed using concurrent thiol click chemistries for hydrogel tissue engineering scaffolds

The integration of biological extracellular matrix (ECM) components and synthetic materials is a promising pathway to fabricate the next generation of hydrogel-based tissue scaffolds that more accurately emulate the microscale heterogeneity of natural ECM. We report the development of a bio/synthetic interpenetrating network (BioSIN_x), containing gelatin methacrylamide (GelMA) polymerized within a poly(ethylene glycol) (PEG) framework to form a mechanically robust network capable of supporting both internal cell encapsulation and surface cell adherence. The covalently crosslinked PEG network was formed by thiol-yne coupling, while the bioactive GelMA was integrated using a concurrent thiol-ene coupling reaction. The physical properties (i.e. swelling, modulus) of BioSIN_x were compared to both PEG networks with physically-incorporated gelatin (BioSIN_P) and homogenous hydrogels. BioSIN_x displayed superior physical properties and significantly lower gelatin dissolution. These benefits led to enhanced cytocompatibility for both cell adhesion and encapsulation; furthermore, the increased physical strength provided for the generation of a micro-engineered tissue scaffold. Endothelial cells showed extensive cytoplasmic spreading and the formation of cellular adhesion sites when cultured onto BioSIN_x; moreover, both encapsulated and adherent cells showed sustained viability and proliferation.     

Nanostructuring biosynthetic hydrogels for tissue engineering: a cellular and structural analysis

The nanostructuring of hydrogel scaffolds used in tissue engineering provides the ability to control cellular fate and tissue morphogenesis through cell-matrix interactions. Here we describe a method to provide nanostructure to a biosynthetic hydrogel scaffold made from crosslinked poly(ethylene glycol)-fibrinogen conjugates (PEG-fibrinogen), by modifying them with the block-copolymer Pluronic® F127. The copolymeric additive self-assembled into micelles at certain concentrations and temperatures, thereby creating nanostructures within the crosslinked hydrogel. Small-angle X-ray scattering (SAXS) and transmission electron microscopy at cryogenic temperature were used to detect Pluronic® F127 micelles embedded within the crosslinked PEG-fibrinogen hydrogels. The density and order of the micelles within the hydrogel matrix increased as the relative Pluronic® F127 concentration was raised. The transient stability of the micelles within the hydrogel network was analyzed using time-dependent swelling and Pluronic® F127 release measurements. These characterizations revealed that most of the Pluronic® F127 molecules diffuse out of the hydrogels after 4 days in aqueous buffer and SAXS analysis confirmed a significant change in the structure and interactions of the micelles during this time. Cell culture experiments evaluating the three-dimensional fibroblast morphology within the matrix indicated a strong correlation between cell spreading and the hydrogel’s characteristic mesh size. The present research thereby provides a more quantitative understanding of how structural features in an encapsulating hydrogel environment can affect cell morphogenesis towards tissue regeneration.     

Non-viral DNA delivery from porous hyaluronic acid hydrogels in mice

The lack of vascularization within tissue-engineered constructs remains the primary cause of construct failure following implantation. Porous constructs have been successful in allowing for vessel infiltration without requiring extensive matrix degradation. We hypothesized that the rate and maturity of infiltrating vessels could be enhanced by complementing the open pore structure with the added delivery of DNA encoding for angiogenic growth factors. Both 100 and 60 μm porous and non-porous hyaluronic acid hydrogels loaded with pro-angiogenic (pVEGF) or reporter (pGFPluc) plasmid nanoparticles were used to study the effects of pore size and DNA delivery on angiogenesis in a mouse subcutaneous implant model. GFP-expressing transfected cells were found inside all control hydrogels over the course of the study, although transfection levels peaked by week 3 for 100 and 60 μm porous hydrogels. Transfection in non-porous hydrogels continued to increase over time corresponding with continued surface degradation. pVEGF transfection levels were not high enough to enhance angiogenesis by increasing vessel density, maturity, or size, although by 6 weeks for all pore size hydrogels more hydrogel implants were positive for vascularization when pVEGF polyplexes were incorporated compared to control hydrogels. Pore size was found to be the dominant factor in determining the angiogenic response with 60 μm porous hydrogels having more vessels/area present than 100 μm porous hydrogels at the initial onset of angiogenesis at 3 weeks. The results of this study show promise for the use of polyplex loaded porous hydrogels to transfect infiltrating cells in vivo and guide tissue regeneration and repair.     

Maximizing cartilage formation and integration via a trajectory-based tissue engineering approach

Given the limitations of current surgical approaches to treat articular cartilage injuries, tissue engineering (TE) approaches have been aggressively pursued. Despite reproduction of key mechanical attributes of native tissue, the ability of TE cartilage constructs to integrate with native tissue must also be optimized for clinical success. In this paper, we propose a “trajectory-based” tissue engineering (TB-TE) approach, based on the hypothesis that time-dependent increases in construct maturation in-vitro prior to implantation (i.e. positive rates) may provide a reliable predictor of in-vivo success. As an example TE system, we utilized hyaluronic acid hydrogels laden with mesenchymal stem cells. We first modeled the maturation of these constructs in-vitro to capture time-dependent changes. We then performed a sensitivity analysis of the model to optimize the timing and amount of data collection. Finally, we showed that integration to cartilage in-vitro is not correlated to the maturation state of TE constructs, but rather their maturation rate, providing a proof-of-concept for the use of TB-TE to enhance treatment outcomes following cartilage injury. This new approach challenges the traditional TE paradigm of matching only native state parameters of maturity and emphasizes the importance of also establishing an in-vitro trajectory in constructs in order to improve the chance of in-vivo success.     

Preparation and characterization of gelatin/hyaluronic acid cryogels for adipose tissue engineering: In vitro and in vivo studies

Macroporous elastic scaffolds containing gelatin (4% or 10%) and 0.25% hyaluronic acid (HA) were fabricated by cryogelation for application in adipose tissue engineering. These cryogels have interconnected pores (～200 μm), high porosity (>90%) and a high degree of cross-linking (>99%). The higher gelatin concentration reduced the pore size, porosity and swelling ratio of the cryogel but improved its swelling kinetics. Compressive mechanical testing of cryogel samples demonstrated non-linear stress–strain behavior and hysteresis loops during loading–unloading cycles, but total recovery from large strains. The presence of more gelatin increased the elastic modulus, toughness and storage modulus and yielded a cryogel that was highly elastic, with a loss tangent equal to 0.03. Porcine adipose-derived stem cells (ADSCs) were seeded in the cryogel scaffolds to assess their proliferation and differentiation. In vitro studies demonstrated a good proliferation rate and the adipogenic differentiation of the ADSCs in the cryogel scaffolds, as shown by their morphological change from a fibroblast-like shape to a spherical shape, decreased actin cytoskeleton content, growth arrest, secretion of the adipogenesis marker protein leptin, Oil Red O staining for triglycerides and expression of early (LPL and PPARγ) and late (aP2 and leptin) adipogenic marker genes. In vivo studies of ADSCs/cryogel constructs implanted in nude mice and pigs demonstrated adipose tissue and new capillary formation, the expression of PPARγ, leptin and CD31 in immunostained explants, and the continued expression of adipocyte-specific genes. Both the in vitro and in vivo studies indicated that the gelatin/HA cryogel provided a structural and chemical environment that enabled cell attachment and proliferation and supported the biological functions and adipogenesis of the ADSCs.     

Controlling the spatial distribution of ECM components in degradable PEG hydrogels for tissue engineering cartilage

In developing a scaffold to support new tissue growth, the degradation rate and mass loss profiles of the scaffold are important design parameters. In this study, hydrogels were prepared by copolymerizing a degradable macromer, poly(lactic acid)-b-poly(ethylene glycol)-b-poly(lactic acid) endcapped with acrylate groups (PEG-LA-DA) with a nondegradable macromer, poly(ethylene glycol) dimethacrylate (PEGDM). The resulting hydrogels exhibited a range of degradation behavior and mass loss profiles. Chondrocytes were photoencapsulated in gels formulated with 50:50, 25:75, and 15:85 (mol % PEGDM: mol % PEG-LA-DA) and cultured for 6 weeks in vitro. The neocartilaginous tissue formed was examined biochemically and histologically. After 6 weeks, the DNA content in gels with 75 and 85% degradable crosslinks was nearly twice that of the DNA content in the 50% gels. The total collagen content was significantly higher in the 85% gel [2.4 +/- 0.8% wet weight (ww)] compared to the 50% gel (0.22 +/- 0.29% ww). In examining the neocartilaginous tissue with immunohistochemistry, type II collagen was localized in the pericellular region in the 50% gel; however, when increased degradation was incorporated into the gel, type II collagen was found throughout the neotissue. In summary, the important role of hydrogel degradation in controlling and influencing the deposition and distribution of extracellular matrix molecules was demonstrated and quantified.     

Injectable in situ dual-crosslinking hyaluronic acid and sodium alginate based hydrogels for drug release

A series of injectable in situ dual-crosslinking hydrogels (HA/ALG) based on oxidized sodium alginate (oxi-ALG) and hyaluronic acid modified with thiol and hydrazide (HA-SH/CDH) were prepared via hydrazone bonds and disulfide bonds. The chemical structures, morphologies, rheological properties, gelling time, swelling ratio, degradation rate and drug release behavior of hydrogels were investigated. HA/ALG hydrogels exhibited tunable gelling time, rheological properties, swelling ratio and degradation rate with varying precursor concentrations. The gelling time of HA/ALG hydrogels ranged from 157?s to 955?s, the values of yield stress of HA2/ALG2, HA3/ALG3 and HA4/ALG4 hydrogels were 1724, 4349 and 5306?Pa, and the degradation percentage of HA2/ALG2, HA3/ALG3 and HA4/ALG4 hydrogels were about 64%, 51% and 42% after incubating 35?days, respectively. Bovine serum albumin (BSA) was used as a model drug to investigate the drug controlled release properties, and the in vitro cumulative release percentage of BSA from HA2/ALG2, HA3/ALG3 and HA4/ALG4 drug-loaded hydrogels were about 79%, 72% and 69% after 20?days. The series of injectable in situ dual-crosslinking HA/ALG hydrogels could be an attractive candidate for drug delivery system, tissue engineering and regenerative medicine.     

Thermosensitive injectable hyaluronic acid hydrogel for adipose tissue engineering

A series of thermosensitive copolymer hydrogels, aminated hyaluronic acid-g-poly(N-isopropylacrylamide) (AHA-g-PNIPAAm), were synthesized by coupling carboxylic end-capped PNIPAAm (PNIPAAm-COOH) to AHA through amide bond linkages. AHA was prepared by grafting adipic dihydrazide to the HA backbone and PNIPAAm-COOH copolymer was synthesized via a facile thermo-radical polymerization technique by polymerization of NIPAAm using 4,4′-azobis(4-cyanovaleric acid) as an initiator, respectively. The structure of AHA and AHA-g-PNIPAAm copolymer was determined by ¹H NMR. Two AHA-g-PNIPAAm copolymers with different weight ratios of PNIPAAm on the applicability of injectable hydrogels were characterized. The lower critical solution temperature (LCST) of AHA-g-PNIPAAm copolymers in PBS were measured as 30 °C by rheological analysis, regardless of the grafting degrees. Enzymatic resistance of AHA-g-PNIPAAm hydrogels with 28% and 53% of PNIPAAm in 100 U/mL hyaluronidase/PBS at 37 °C was 12.3% and 37.6% over 28 days, respectively. Equilibrium swelling ratios of AHA-g-PNIPAAm hydrogels with 28% of PNIPAAm were 21.5, and significantly decreased to 13.3 with 53% of PNIPAAm in PBS at 37 °C. Results from SEM observations confirm a porous 3D AHA-g-PNIPAAm hydrogel structure with interconnected pores after freeze-drying and the pore diameter depends on the weight ratios of PNIPAAm. Encapsulation of human adipose-derived stem cells (ASCs) within hydrogels showed the AHA-g-PNIPAAm copolymers were noncytotoxic and preserved the viability of the entrapped cells. A preliminary in vivo study demonstrated the usefulness of the AHA-g-PNIPAAm copolymer as an injectable hydrogel for adipose tissue engineering. This newly described thermoresponsive AHA-g-PNIPAAm copolymer demonstrated attractive properties to serve as cell or pharmaceutical delivery vehicles for a variety of tissue engineering applications.     

透明质酸在骨组织工程研究中的应用现状

背景：用组织工程学方法促进骨组织再生,是近年来骨缺损修复的研究热点。支架材料是骨组织工程研究的重要内容。 目的：分析透明质酸作为骨组织工程支架材料的应用进展。 方法：对CNKI、PubMed数据库进行文献检索,以“透明质酸,骨”为中文检索词、“hyaluronic acid, bone“为英文检索词。提取文献进行透明质酸作为骨组织工程支架材料的应用研究的分析。分析了透明质酸的物理特性,透明质酸在骨组织工程中的应用,以及相关文献的发表情况。 结果与结论：透明质酸是一种重要的细胞外基质,透明质酸及其衍生物有优良的特性,是构建组织工程支架的优良材料,且可作为生长因子及细胞的输送载体。国家自然科学基金是资助透明质酸作为骨组织工程支架材料的应用的相关文献最多的基金,湖北中医学院、解放军总医院、广州中医药大学、华南理工大学发表相关文献较多。近年透明质酸在骨组织工程上的应用研究引起了越来越多的关注,但其临床研究较少。     

Single and dual crosslinked oxidized methacrylated alginate/PEG hydrogels for bioadhesive applications

A degradable, cytocompatible bioadhesive can facilitate surgical procedures and minimize patient pain and post-surgical complications. In this study a bioadhesive hydrogel system based on oxidized methacrylated alginate/8-arm poly(ethylene glycol) amine (OMA/PEG) has been developed, and the bioadhesive characteristics of the crosslinked OMA/PEG hydrogels evaluated. Here we demonstrate that the swelling behavior, degradation profiles, and storage moduli of crosslinked OMA/PEG hydrogels are tunable by varying the degree of alginate oxidation. The crosslinked OMA/PEG hydrogels exhibit cytocompatibility when cultured with human bone marrow-derived mesenchymal stem cells. In addition, the adhesion strength of these hydrogels, controllable by varying the alginate oxidation level and measured using a porcine skin model, is superior to commercially available fibrin glue. This OMA/PEG hydrogel system with controllable biodegradation and mechanical properties and adhesion strength may be a promising bioadhesive for clinical use in biomedical applications, such as drug delivery, wound closure and healing, biomedical device implantation, and tissue engineering.     

Four-arm PEG cross-linked hyaluronic acid hydrogels containing PEGylated apoptotic TRAIL protein for treating pancreatic cancer

Four-arm polyethylene glycol (PEG) cross-linked hyaluronic acid (HA) hydrogels containing PEGylated tumor necrosis factor-related apoptosis-inducing ligand (PEG-TRAIL) were fabricated, and their antitumor effects were evaluated in pancreatic cell (Mia Paca-2)-xenografted mice. HA was conjugated with 4-arm PEG_10k-amine (a cross-linker) at ratios of 100:1 and 100:2 using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide hydrochloride as a cross-linker, and TRAIL or PEG-TRAIL was incorporated into these HA hydrogels. HA hydrogels at a 100:1 ratio were prepared in good yields (>88%), were moderately stiff, and gradually released PEG-TRAIL over ∼14 days in vitro and over ∼7 days in vivo (as determined by high-pressure liquid chromatography and infrared imaging). The released PEG-TRAIL was found to have obvious apoptotic activity in Mia Paca-2 cells. PEG-TRAIL HA hydrogels displayed remarkably more antitumor efficacy than TRAIL HA hydrogels in Mia Paca-2 cell-xenografted mice in terms of tumor volumes (size) and weights (453.2 mm³ and 1.03 g vs. 867.5 mm³ and 1.86 g). Furthermore, this improved antitumor efficacy was found to be due to the apoptotic activity of PEG-TRAIL in vivo (determined by a TUNEL assay) despite its substantially lower cytotoxicity than native TRAIL (IC₅₀ values: 71.8 and 202.5 ng ml⁻¹, respectively). This overall enhanced antitumor effect of PEG-TRAIL HA hydrogels appeared to be due to the increased stability of PEGylated TRAIL in HA hydrogels. These findings indicate that this HA hydrogel system combined with PEG-TRAIL should be considered a potential candidate for the treatment of pancreatic cancer.     

Injectable in situ cross-linking hyaluronic acid/carboxymethyl cellulose based hydrogels for drug release

A series of injectable in situ cross-linking hyaluronic acid/carboxymethyl cellulose based hydrogels (HA/CMC) was prepared via disulfide bonds by the oxidation of dissolved oxygen. The results showed that HA/CMC hydrogels exhibited tunable gelling time, appropriate rheology properties, high swelling ratio, good stability, and sustained drug release ability. The gelling time of HA/CMC hydrogels ranged from 1.4 to 7.0 min, and the values of the storage modulus, complex shear modulus, dynamic viscosity, and yield stress of HA3/CMC3 hydrogel were about 5869 Pa, 5870 Pa, 587 Pa·s, and 1969 Pa, respectively. The degradation percentage of HA1/CMC1, HA2/CMC2, and HA3/CMC3 hydrogels were about 60, 49, and 41% after incubating 42 days, and the in vitro cumulative release percentage of BSA from HA1/CMC1, HA2/CMC2, and HA3/CMC3 drug-loaded hydrogels were about 99, 91, and 82% after 30 days. The series of injectable in situ cross-linking HA/CMC hydrogels exhibited good comprehensive performance, signifying that these hydrogels could be potentially used in the fields of short- and medium-term controlled drug release, cell encapsulation, regenerative medicine, and tissue engineering.     

Dermis isolated adult stem cells for cartilage tissue engineering

Adult stem cells from the dermal layer of skin are an attractive alternative to primary cells for meniscus engineering, as they may be easily obtained and used autologously. Recently, chondroinducible dermis cells from caprine skin have shown promising characteristics for cartilage tissue engineering. In this study, their multilineage differentiation capacity is determined, and methods of expanding and tissue engineering these cells are investigated. It was found that these cells could differentiate along adipogenic, osteogenic, and chondrogenic lineages, allowing them to be termed dermis isolated adult stem cells (DIAS cells). Focusing on cartilage tissue engineering, it was found that passaging these cells in chondrogenic medium and forming them into self-assembled tissue engineered constructs caused upregulation of collagen type II and COMP gene expression. Further investigation showed that applying transforming growth factor β1 (TGF-β1) or bone morphogenetic protein 2 (BMP-2) to DIAS constructs caused increased sulfated glycosaminoglycan content. Additionally, TGF-β1 treatment caused significant increases in compressive properties and construct contraction. In contrast, BMP-2 treatment resulted in the largest constructs, but did not increase compressive properties. These results show that DIAS cells can be easily manipulated for cartilage tissue engineering strategies, and may also be a useful cell source for other mesenchymal tissues.     

牙髓牙本质组织工程生物支架材料的研究进展

背景：组织工程方法中选择合适的支架是关键性的步骤。 目的：回顾分析牙髓牙本质组织工程中支架材料的应用研究。 方法：由第一作者检索1993至2012年 PubMed数据及万方数据库有关牙髓牙本质组织工程中支架材料应用研究等方面的文献。 结果与结论：在牙髓牙本质组织工程中有包括天然生物、人工合成材料和复合材料在内的大量生物材料可供选择,每一种材料都有各自的生物学特点。其中胶原、聚酯、羟基磷灰石等是研究较多的支架材料。自组装多肽水凝胶是由氨基酸制成的新型支架材料,满足理想牙髓牙本质组织工程支架材料的大部分要求,是一种前景广阔的牙髓牙本质组织工程支架材料。