Fabrication of transferable micropatterned-co-cultured cell sheets with microcontact printing

The purpose of the present study is to develop a novel method for the fabrication of transferable micropatterned cell sheets for tissue engineering. To achieve this development, microcontact printing of fibronectin on commercially available temperature-responsive dishes was employed. Primary rat hepatocytes were seeded on the dish surfaces printed with fibronectin. Under serum-free conditions, hepatocytes were attached onto fibronectin domains selectively. Then, a second cell type of endothelial cells was seeded in the presence of serum. Double fluorescent staining revealed that endothelial cells successfully adhered to the intervals of hepatocyte domains. Finally, all the cells were harvested as a single contiguous micropatterned cell sheet upon temperature-reduction. With a cell sheet manipulator having a gelatin layer for the support of harvested cell sheets, harvested micropatterned cell sheets were transferred to new dish surfaces. This technique would be useful for the fabrication of thick tissue constructs having a complex microarchitecture.     

A model retinal interface based on directed neuronal growth for single cell stimulation

In this work, we use cell micropatterning technologies to direct neuronal growth to individual electrodes, and demonstrate that such an approach can achieve selective stimulation and lower stimulation thresholds than current field-effect based retinal prostheses. Rat retinal ganglion cells (RGCs) were purified through immunopanning techniques, and microcontact printing (μCP) was applied to align and pattern laminin on a microelectrode array, on which the RGCs were seeded and extended neurites along the pattern to individual electrodes. The stimulation threshold currents of RGCs micropatterned to electrodes were found to be significantly less than those of non-patterned RGCs over a wide range of electrode-soma distances, as determined with calcium imaging techniques. Moreover, the stimulation threshold for micropatterned cells was found to be independent of electrode-soma distance, and there was no significant effect of μCP on cell excitability. The effects of additional stimulation parameters, such as electrode size and pulse duration, on threshold currents were determined. The stimulation results quantitatively demonstrate the potential benefits of a retinal prosthetic interface based on directed neuronal growth.     

Engineered heart slices for electrophysiological and contractile studies

A major consideration in the design of engineered cardiac tissues for the faithful representation of physiological behavior is the recapitulation of the complex topography and biochemistry of native tissue. In this study we present engineered heart slices (EHS), which consist of neonatal rat ventricular cells (NRVCs) seeded onto thin slices of decellularized cardiac tissue that retain important aspects of native extracellular matrix (ECM). To form EHS, rat or pig ventricular tissue was sectioned into 300 μm-thick, 5 to 16 mm-diameter disks, which were subsequently decellularized using detergents, spread on coverslips, and seeded with NRVCs. The organized fiber structure of the ECM remained after decellularization and promoted cell elongation and alignment, resulting in an anisotropic, functional tissue that could be electrically paced. Contraction decreased at higher pacing rates, and optical mapping revealed electrical conduction that was anisotropic with a ratio of approximately 2.0, rate-dependent shortening of the action potential and slowing of conduction, and slowing of conduction by the sodium channel blocker lidocaine. Reentrant arrhythmias could also be pace-induced and terminated. EHS constitute an attractive in vitro cardiac tissue in which cardiac cells are cultured on thin slices of decellularized cardiac ECM that provide important biochemical, structural, and mechanical cues absent in traditional cell cultures.     

Microtopographically patterned surfaces promote the alignment of tenocytes and extracellular collagen

This paper investigates the role of microtopographical features on the cytomorphology, alignment, proliferation and gene expression of tenocytes. We made use of simple microfabrication approaches to create surfaces patterned with topographical features suitable for in vitro studies of tenocytes. These surfaces were composed of glass substrates patterned with polymeric ridges spaced from 50 to 250 μm apart. Our studies demonstrate that the microgrooves differentially impact tenocyte shape, alignment and matrix organization along the direction of grooves. Groove widths significantly influenced cellular alignment, with 50 μm grooved patterns affecting alignment most substantially. Polarized light microscopy demonstrated that mature collagen fibers were denser and more oriented within 50 μm patterns. None of the patterns had a significant effect on the expression of genes linked to proliferation or extracellular matrix synthesis, although time in culture profoundly influenced both gene groups. COMP mRNA expression was moderately increased in tenocytes seeded onto 250 μm grooves, but there was no overall beneficial phenotypic effect of aligned growth. The results of this study indicate that microtopography affects cell density and alignment of tenocytes and leads to the deposition of an aligned collagen matrix, but does not significantly impact matrix gene expression or cell phenotype. These outcomes provide insights into the biology of tendon regeneration, thus providing guidance in the design of clinical procedures for tendon repair.     

Engineering high-density endothelial cell monolayers on soft substrates

This study demonstrates that a confluent monolayer of endothelial cells (ECs) can be tissue engineered on a soft substrate with a cell density and morphology that approximates in vivo conditions. We achieved formation of a confluent EC monolayer on polydimethylsiloxane (PDMS) elastomer by microcontact printing of fibronectin (FN) in a square lattice array of 3 μm diameter circular islands at a 6 μm pitch. Uniform coatings of FN or serum proteins on PDMS or on tissue-culture-treated polystyrene failed to support the equivalent EC density and/or confluence. The ECs on the FN micropatterned PDMS achieved a density of 1,536 ± 247 cells mm^?2, close to the 3,215 ± 336 cells mm^?2 observed in vivo from porcine pulmonary artery and significantly higher (2- to 5-fold) than EC density on other materials. The probable mechanism for enhanced EC adhesion, growth and density is increased focal adhesion (FA) formation between the ECs and the substrate. After 14 days culture, the micropatterned FN surface increased the average number of FAs per cell to 35 ± 10, compared to 7 ± 6 for ECs on PDMS uniformly coated with FN. Thus, microscale patterning of FN into FA-sized, circular islands on PDMS elastomer promotes the formation of EC monolayers with in vivo-like cell density and morphology.     

表面改性及微沟槽技术对肌腱细胞生长与取向的影响

利用光刻技术制作微格式模板,微接触转印法制作微沟槽PDMS表面,微流道技术裱衬不同浓度的Ⅰ型胶原于微沟槽表面上,比较其对细胞生长形态及生长取向的影响.对照组为未裱衬胶原的微沟槽、平板PDMS及裱衬胶原的平板PDMS.种植SD大鼠肌腱细胞在材料上,于37℃孵箱中培养48 h.采用MTT比色法测定不同浓度的胶原对肌腱细胞的生长增殖的影响.通过倒置相差显微镜、扫描电镜、荧光显微镜观察细胞生长的形态,取向情况.结果显示:Ⅰ型胶原修饰的PDMS微沟槽材料比未裱衬胶原的对照组具有明显的促细胞生长的作用(P＜0.05),并且随着胶原浓度的增加作用越明显.有微沟槽表面的材料对细胞的生长形态和生长取向有明显影响.提示,Ⅰ型胶原修饰的微沟槽材料不仅能规范肌腱细胞的生长取向,而且能促进肌腱细胞的生长,从而得到理想的细胞生长形态,该结果对工程化肌腱的构建有重要的指导意义.     

Engineering multi-layered skeletal muscle tissue by using 3D microgrooved collagen scaffolds

Preparation of three-dimensional (3D) micropatterned porous scaffolds remains a great challenge for engineering of highly organized tissues such as skeletal muscle tissue and cardiac tissue. Two-dimensional (2D) micropatterned surfaces with periodic features (several nanometers to less than 100 μm) are commonly used to guide the alignment of muscle myoblasts and myotubes and lead to formation of pre-patterned cell sheets. However, cell sheets from 2D patterned surfaces have limited thickness, and harvesting the cell sheets for implantation is inconvenient and can lead to less alignment of myotubes. 3D micropatterned scaffolds can promote cell alignment and muscle tissue formation. In this study, we developed a novel type of 3D porous collagen scaffolds with concave microgrooves that mimic muscle basement membrane to engineer skeletal muscle tissue. Highly aligned and multi-layered muscle bundle tissues were engineered by controlling the size of microgrooves and cell seeding concentration. Myoblasts in the engineered muscle tissue were well-aligned and had high expression of myosin heavy chain and synthesis of muscle extracellular matrix. The microgrooved collagen scaffolds could be used to engineer organized multi-layered muscle tissue for implantation to repair/restore the function of diseased tissues or be used to investigate the cell–cell interaction in 3D microscale topography.     

Cultivating liver cells on printed arrays of hepatocyte growth factor

Growth factors are commonly present in soluble form during in vitro cell cultivation experiments in order to provide signals for cellular proliferation or differentiation. In contrast to these traditional experiments, we investigated solid-phase presentation of a hepatocyte growth factor (HGF), a protein important in liver development and regeneration, on microarrays of extracellular matrix (ECM) proteins. In our experiments, HGF was mixed in solution with ECM proteins (collagen (I), (IV) or laminin) and robotically printed onto silane-modified glass slides. Primary rat hepatocytes were seeded onto HGF/ECM protein microarrays and formed cellular clusters that corresponded in size to the dimensions of individual protein spots (500 μm diameter). Analysis of liver-specific products, albumin and α1-antitrypsin, revealed several fold higher levels of expression of these proteins in hepatocytes cultured on HGF/ECM microarrays compared to cells cultivated on ECM proteins alone. In addition, cultivation of hepatocytes on HGF/ECM protein spots led to spontaneous reorganization of cellular clusters from a monolayer into three-dimensional spheroids. We also investigated the effects of surface-tethered HGF on hepatocytes co-cultivated with stromal cells and observed a significantly higher level of albumin in co-cultures where hepatocytes were stimulated by HGF/ECM spots compared to co-cultures created on ECM protein islands without the growth factor. In summary, our study suggests that incorporation of HGF into ECM protein microarrays has a profound and long-lasting effect on the morphology and phenotype of primary hepatocytes. In the future, the number of growth factors printed on ECM microarrays will be expanded to enable multiplexed and combinatorial screening of inducers of cellular differentiation or proliferation.     

Printing patterns of biospecifically-adsorbed protein

The advancement of elastomeric patterning techniques in recent years has significantly enhanced our ability to spatially control biomaterial surface chemistry at the micrometre level. The application of this technology to the patterning of biomolecules onto solid surfaces has created many potential applications including the development of advanced biosensors, combinatorial library screening and the formation of tissue engineering templates. In this paper, we describe the direct patterning of protein by microcontact printing. An important consideration for the fabrication of protein micropatterns intended for these applications is the nature of the protein immobilization to a substrate. To date, the patterning of proteins by direct microcontact printing (μCP) has relied on the non-covalent adsorption to a substrate. Ideally, the proteins need to be firmly anchored onto a surface without adversely effecting their activity. Here, the high affinity avidin-biotin receptor-ligand interaction has been exploited to form arrays of avidin molecules onto a polymeric substrate expressing biotin moieties. This has created a generic technique by which any biotinylated species can be subsequently immobilized into defined patterns. Utilizing atomic force microscopy (AFM), the patterned surfaces have been characterized to molecular resolution. The micropatterned sample supported cell adhesion when biotin-(G)₁₁-GRGDS was bound to the avidin bearing arrays.     

A matrix micropatterning platform for cell localization and stem cell fate determination

To study the role of cell–extracellular matrix (ECM) interactions, microscale approaches provide the potential to perform high throughput assessment of the effect of the ECM microenvironment on cellular function and phenotype. Using a microscale direct writing (MDW) technique, we characterized the generation of multicomponent ECM microarrays for cellular micropatterning, localization and stem cell fate determination. ECMs and other biomolecules of various geometries and sizes were printed onto epoxide-modified glass substrates to evaluate cell attachment by human endothelial cells. The endothelial cells displayed strong preferential attachment to the ECM patterned regions and aligned their cytoskeleton along the direction of the micropatterns. We next generated ECM microarrays that contained one or more ECM components (namely gelatin, collagen IV and fibronectin) and then cultured murine embryonic stem cell (ESCs) on the microarrays. The ESCs selectively attached to the micropatterned features and expressed markers associated with a pluripotent phenotype, such as E-cadherin and alkaline phosphatase, when maintained in growth medium containing leukemia inhibitory factor. In the presence of the soluble factors retinoic acid and bone morphogenetic protein-4 the ESCs differentiated towards the ectodermal lineage on the ECM microarray with differential ECM effects. The ESCs cultured on gelatin showed significantly higher levels of pan cytokeratin expression, when compared with cells cultured on collagen IV or fibronectin, suggesting that gelatin preferentially promotes ectodermal differentiation. In summary, our results demonstrate that MDW is a versatile approach to print ECMs of diverse geometries and compositions onto surfaces, and it is amenable to the generation of multicomponent ECM microarrays for stem cell fate determination.     

Biodegradable microgrooved polymeric surfaces obtained by photolithography for skeletal muscle cell orientation and myotube development

During tissue formation, skeletal muscle precursor cells fuse together to form multinucleated myotubes. To understand this mechanism, in vitro systems promoting cell alignment need to be developed; for this purpose, micrometer-scale features obtained on substrate surfaces by photolithography can be used to control and affect cell behaviour. This work was aimed at investigating how differently microgrooved polymeric surfaces can affect myoblast alignment, fusion and myotube formation in vitro. Microgrooved polymeric films were obtained by solvent casting of a biodegradable poly-l-lactide/trimethylene carbonate copolymer (PLLA–TMC) onto microgrooved silicon wafers with different groove widths (5, 10, 25, 50, 100 μm) and depths (0.5, 1, 2.5, 5 μm), obtained by a standard photolithographic technique. The surface topography of wafers and films was evaluated by scanning electron microscopy. Cell assays were performed using C2C12 cells and myotube formation was analysed by immunofluorescence assays. Cell alignment and circularity were also evaluated using ImageJ software. The obtained results confirm the ability of microgrooved surfaces to influence myotube formation and alignment; in addition, they represent a novel further improvement to the comprehension of best features to be used. The most encouraging results were observed in the case of microstructured PLLA–TMC films with grooves of 2.5 and 1 μm depth, presenting, in particular, a groove width of 50 and 25 μm.     

Oriented astroglial cell growth on micropatterned polystyrene substrates

In an effort to develop a permissive environment for neural stem cell differentiation, directional growth of astrocytes has been achieved on polymer substrates in vitro. Manipulating a combination of physical and chemical cues, astrocyte adhesion and alignment in vitro were examined. To provide physical guidance, micropatterned polymer substrates of polystyrene (PS) were fabricated. Laminin was selectively adsorbed onto the grooves of the patterned surface. Rat type-1 astrocytes were seeded onto the micropatterned PS substrates, and the effects of substrate topography and the adsorption of laminin to the PS substrates on the behavior and morphology of the astrocytes were explored. The astrocytes were found to align parallel to the micropatterned grooves at initial seeding densities of approximately 7500, 13,000, and 20,000 cells/cm(2) due to the effects of the physical and chemical guidance mechanisms. Adsorbing laminin in the microgrooves of the micropatterned PS substrates improved cell adhesion and spreading of cytoskeletal filaments significantly. At these initial seeding densities, over 85% astrocyte alignment in the direction of the grooves was achieved on the micropatterned PS substrates with laminin adsorbed in the grooves. This combination of guidance cues has the potential to provide a permissive substrate for in vivo regeneration within the central nervous system.     

Spatially organized layers of cardiomyocytes on biodegradable polyurethane films for myocardial repair

Tissue engineering constructs should match the physical and mechanical properties of the native tissue. This implies that pliable scaffolds might be better suited for soft-tissue applications than rigid polymeric materials. In this study, we examined spatially organized cardiomyocyte cultures on biodegradable, elastomeric polyurethane films patterned by microcontact printing of laminin lanes. The resulting cardiomyocyte patterns on polyurethane displayed a similar morphology to those previously achieved for up to 7-10 days on other substrates, such as polystyrene dishes. However, the integrity of the cardiomyocyte patterns on thin, spin-cast or solvent-cast polyurethane films was retained for up to 4 weeks in culture. When additional cardiomyocytes (labeled with Cell Tracker reagents) were seeded onto the patterned cultures, secondary and tertiary cell populations aligned between and on top of the primary patterned cells to form a multilayered, organized tissue construct approximately 2-3 cell layers thick. In addition, dense, highly aligned monolayers of patterned cardiomyocytes were able to contract the thin, solvent-cast polyurethane films. These results indicate that elastomeric, biodegradable polyurethane films can serve as an appropriate scaffold material to support stably the engineering of spatially organized layers of cardiomyocytes in vitro. This approach may serve as a novel method for transplantation of organized cardiac tissue constructs to the heart for myocardial repair.     

Micropatterned dermal–epidermal regeneration matrices create functional niches that enhance epidermal morphogenesis

Although tissue engineered skin substitutes have demonstrated some clinical success for the treatment of chronic wounds such as diabetic and venous ulcers, persistent graft take and stability remain concerns. Current bilayered skin substitutes lack the characteristic microtopography of the dermal–epidermal junction that gives skin enhanced mechanical stability and creates cellular microniches that differentially promote keratinocyte function to form skin appendages and enhance wound healing. We developed a novel micropatterned dermal–epidermal regeneration matrix (μDERM) which incorporates this complex topography and substantially enhances epidermal morphology. Here, we describe the use of this three-dimensional (3-D) in vitro culture model to systematically evaluate different topographical geometries and to determine their relationship to keratinocyte function. We identified three distinct keratinocyte functional niches: the proliferative niche (narrow geometries), the basement membrane protein synthesis niche (wide geometries) and the putative keratinocyte stem cell niche (narrow geometries and corners). Specifically, epidermal thickness and keratinocyte proliferation is significantly (p < 0.05) increased in 50 and 100 μm channels while laminin-332 deposition is significantly (p < 0.05) increased in 400 μm channels compared to flat controls. Additionally, β₁^brip63⁺ keratinocytes, putative keratinocyte stem cells, preferentially cluster in channel geometries (similar to clustering observed in native skin) compared to a random distribution on flats. This study identifies specific target geometries to enhance skin regeneration and graft performance. Furthermore, these results suggest the importance of μDERM microtopography in designing the next generation of skin substitutes. Finally, we anticipate that 3-D organotypic cultures on μDERMS will provide a novel tissue engineered skin substitute for in vitro investigations of skin morphogenesis, wound healing and pathology.     

Optimizing the structure and contractility of engineered skeletal muscle thin films

An experimental system was developed to tissue engineer skeletal muscle thin films with well-defined tissue architecture and to quantify the effect on contractility. Using the C2C12 cell line, the authors tested whether tailoring the width and spacing of micropatterned fibronectin lines can be used to increase myoblast differentiation into functional myotubes and maximize uniaxial alignment within a 2-D sheet. Using a combination of image analysis and the muscular thin film contractility assay, it was demonstrated that a fibronectin line width of 100 μm and line spacing of 20 μm is able to maximize the formation of anisotropic, engineered skeletal muscle with consistent contractile properties at the millimeter length scale. The engineered skeletal muscle exhibited a positive force–frequency relationship, could achieve tetanus and produced a normalized peak twitch stress of 9.4 ± 4.6 kPa at 1 Hz stimulation. These results establish that micropatterning technologies can be used to control skeletal muscle differentiation and tissue architecture and, in combination with the muscular thin film contractility, assay can be used to probe structure–function relationships. More broadly, an experimental platform is provided with the potential to examine how a range of microenvironmental cues such as extracellular matrix protein composition, micropattern geometries and substrate mechanics affect skeletal muscle myogenesis and contractility.     

Influence of nanopatterns on endothelial cell adhesion: Enhanced cell retention under shear stress

In this study, nanopatterned crosslinked films of collagen Type I were seeded with human microvascular endothelial cells and tested for their suitability for vascular tissue engineering. Since the films will be rolled into tubes with concentric layers of collagen, nutrient transfer through the collagen films is quite crucial. Molecular diffusivity through the collagen films, cell viability, cell proliferation and cell retention following shear stress were studied. Cells were seeded onto linearly nanogrooved films (groove widths of 332.5, 500 and 650 nm), with the grooves aligned in the direction of flow. The nanopatterns did not affect cell proliferation or initial cell alignment; however, they significantly affected cell retention under fluid flow. While cell retention on unpatterned films was 35 ± 10%, it was 75 ± 4% on 332.5 nm patterned films and even higher, 91 ± 5%, on 650 nm patterned films. The films were found to have diffusion coefficients of ca. 10⁻⁶ cm² s⁻¹ for O₂ and 4-acetaminophenol, which is comparable to that observed in natural tissues. This constitutes another positive asset of these films for consideration as a scaffold material for vascular tissue engineering.     

Digital micromirror device projection printing system for meniscus tissue engineering

Meniscus degeneration due to age or injury can lead to osteoarthritis. Although promising, current cell-based approaches show limited success. Here we present three-dimensional methacrylated gelatin (GelMA) scaffolds patterned via projection stereolithography to emulate the circumferential alignment of cells in native meniscus tissue. Cultured human avascular zone meniscus cells from normal meniscus were seeded on the scaffolds. Cell viability was monitored, and new tissue formation was assessed by gene expression analysis and histology after 2 weeks in serum-free culture with transforming growth factor β1 (10 ng ml^?1). Light, confocal and scanning electron microscopy were used to observe cell–GelMA interactions. Tensile mechanical testing was performed on unseeded, fresh scaffolds and 2-week-old cell-seeded and unseeded scaffolds. 2-week-old cell–GelMA constructs were implanted into surgically created meniscus defects in an explant organ culture model. No cytotoxic effects were observed 3 weeks after implantation, and cells grew and aligned to the patterned GelMA strands. Gene expression profiles and histology indicated promotion of a fibrocartilage-like meniscus phenotype, and scaffold integration with repair tissue was observed in the explant model. We show that micropatterned GelMA scaffolds are non-toxic, produce organized cellular alignment, and promote meniscus-like tissue formation. Prefabrication of GelMA scaffolds with architectures mimicking the meniscus collagen bundle organization shows promise for meniscal repair. Furthermore, the technique presented may be scaled up to repair larger defects.     

Production of arrays of cardiac and skeletal muscle myofibers by micropatterning techniques on a soft substrate

Micropatterning and microfabrication techniques have been widely used to pattern cells on surfaces and to have a deeper insight into many processes in cell biology such as cell adhesion and interactions with the surrounding environment. The aim of this study was the development of an easy and versatile technique for the in vitro production of arrays of functional cardiac and skeletal muscle myofibers using micropatterning techniques on soft substrates. Cardiomyocytes were used for the production of oriented cardiac myofibers whereas mouse muscle satellite cells for that of differentiated parallel myotubes. We performed micro-contact printing of extracellular matrix proteins on soft polyacrylamide-based hydrogels photopolymerized onto functionalized glass slides. Our methods proved to be simple, repeatable and effective in obtaining an extremely selective adhesion of both cardiomyocytes and satellite cells onto patterned soft hydrogel surfaces. Cardiomyocytes resulted in aligned cardiac myofibers able to exhibit a synchronous contractile activity after 2 days of culture. We demonstrated for the first time that murine satellite cells, cultured on a soft hydrogel substrate, fuse and form aligned myotubes after 7 days of culture. Immunofluorescence analyses confirmed correct expression of cell phenotype, differentiation markers and sarcomeric organization. These results were obtained in myotubes derived from satellite cells from both wild type and MDX mice which are research models for the study of muscle dystrophy. These arrays of both cardiac and skeletal muscle myofibers could be used as in vitro models for pharmacological screening tests or biological studies at the single fiber level. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Retinal pigment epithelial cell function on substrates with chemically micropatterned surfaces

Model substrates with desired chemical micropatterns were fabricated using a microcontact printing technique. The substrate surfaces contained organized arrays of circular glass domains with a diameter of either 10 or 50 microm surrounded and separated by regions modified with octadecyltrichlorosilane (OTS) self-assembled monolayers (SAMs). The effects of surface patterning on in vitro cell attachment, proliferation, morphology, and cytoskeletal organization were evaluated using a human retinal pigment epithelium (RPE) cell line. Both micropatterns affected initial RPE cell attachment, limited cell spreading, and promoted the characteristic cuboidal cell morphology throughout the culture period. In contrast, RPE cells on plain glass control were elongated and appeared fibroblast-like prior to confluence. In addition, cells seeded at 30,000 cell/cm2 on the patterned surfaces maintained a normal pattern of actin and cytokeratin expression, and formed confluent monolayers within 4 days of culture. The cell density increased about 30-fold on both micropatterns by day 7. These results show that it is feasible to control RPE cell shape and expression of differentiated phenotype using micropatterned surfaces.     

Micropatterning of three-dimensional electrospun polyurethane vascular grafts

The uniform alignment of endothelial cells inside small-diameter synthetic grafts can be directed by surface topographies such as microgrooves and microfibers to recapitulate the flow-induced elongation and alignment of natural endothelium. These surface micropatterns may also promote directional migration and potentially improve anastomotic ingrowth of endothelial cells inside the synthetic grafts. In this paper, we developed electrospinning and spin casting techniques to pattern the luminal surface of small-diameter polyurethane (PU) grafts with microfibers and microgrooves, respectively, and evaluated endothelial cell orientation on these surface micropatterns. Tracks of circumferentially oriented microfibers were generated by electrospinning PU onto a mandrel rotated at high velocity, whereas longitudinal tracks of microgrooves were generated by spin casting PU over a rotating poly(dimethylsiloxane) mold. We found that both PU grafts possessed longitudinal Young’s moduli in the range of 0.43 ± 0.04 to 2.00 ± 0.40 MPa, comparable with values obtained from native artery. Endothelial cells seeded onto the grafts formed confluent monolayers with individual cells exhibiting elongated morphology parallel to the micropatterns. The cells were phenotypically similar to natural endothelium as assessed by the expression of the endothelial cell-specific marker, vascular endothelial cell cadherin. In addition, the cells were also responsive to stimulation with the pro-inflammatory cytokine tumor necrosis factor-α as assessed by the inducible expression of intercellular adhesion molecule-1. These results demonstrate that our micropatterned PU grafts possessed longitudinal Young’s moduli in the same range as native vascular tissue and were capable of promoting the formation of aligned and cytokine-responsive endothelial monolayers.