Kinetics of poly(propylene fumarate) synthesis by step polymerization of diethyl fumarate and propylene glycol using zinc chloride as a catalyst

Diethyl fumarate and propylene glycol were reacted in the presence of a zinc chloride catalyst to synthesize poly(propylene fumarate) (PPF) over a period of 12 hours. The kinetics of the transesterification polymerization at 130°C, 150°C, and 200°C were determined by gel permeation chromatography (GPC) analysis. The initial rate of polymerization at each temperature was quantified by calculating the rate of change of the number average molecular weight (Mn). At 200°C, gelation of the PPF occurred after 4 h. GPC analysis of the reaction showed that PPF synthesized at 150°C had a higher final Mn of 4600 (±190) and a higher weight average molecular weight of 10 500 (±760) than at 130°C (n = 3). The chemical structure of the PPF was verified by NMR and FT-IR analysis. This study demonstrated that the maximum Mn of PPF by a transesterification reaction is limited due to gelation of PPF at high temperature.     

Photocrosslinking characteristics and mechanical properties of diethyl fumarate/poly(propylene fumarate) biomaterials

The development of tissue engineered materials for the treatment of large bone defects would provide attractive alternatives to the autografts, allografts, non-degradable polymers, ceramics, and metals that are currently used in clinical settings. To this end, poly(propylene fumarate) (PPF), a viscous polyester synthesized from diethyl fumarate (DEF), has been studied for use as an engineered bone graft. We have investigated the photocrosslinking of PPF dissolved in its precursor, DEF, using the photoinitiator bis(2,4,6-trimethylbenzoyl) phenylphosphine oxide (BAPO) and low levels of ultraviolet light exposure. A three factor, 2 x 2 x 4 factorial design was developed, studying the effects of PPF number average molecular weight, BAPO initiator content, and DEF content upon photocrosslinking characteristics and mechanical properties. Uncured DEF/PPF solution viscosity fell over three orders of magnitude as DEF content was increased from 0% to 75%. The exothermic photocrosslinking reaction released low levels of heat, with no more than 160J/g released from any formulation tested. As a result, the maximum photocrosslinking temperature remained below 47 degrees C for all samples. Both sol fraction and swelling degree generally increased with increasing DEF content. Compressive mechanical properties were within the range of trabecular bone, with the strongest samples possessing an elastic modulus of 195.3 +/- 17.5 MPa and a fracture strength of 68.8 +/- 9.4MPa. Finally, the results indicate that PPF crosslinking was facilitated at low DEF precursor concentrations, but hindered at higher precursor concentrations. These novel DEF/PPF solutions may be preferred over pure PPF as the basis for an engineered bone graft because they (1) exhibit reduced viscosity and thus are easily handled, (2) form polymer networks with compressive strength at fracture suitable for consideration for trabecular bone replacement, and (3) may be readily fabricated into solids with a wide range of structures.     

Synthesis of poly(propylene fumarate) by acylation of propylene glycol in the presence of a proton scavenger

To synthesize high molecular weight poly(propylene fumarate) (PPF), fumaryl chloride and propylene glycol were reacted in the presence of potassium carbonate, which serves as a proton scavenger. Transesterification of the resulting low molecular weight oligomer led to a polymer with greater molecular weight than those from previous reaction methods without requiring the use of a catalyst. According to two-dimensional NMR, the backbone structure of this polymer was as expected and contained no byproducts formed by acid catalyzed addition across the fumarate double bond. Kinetic studies of the transesterification showed that the molecular weight reached a final Mn of 4900 (+/-700) and Mw of 9100 (+/-1300) after 16 h, while the polydispersity index remained below 1.8 throughout the reaction. Thus the PPF synthesized by the new method is of higher molecular weight and greater purity than our previously prepared material.     

Injectable biodegradable polymer composites based on poly(propylene fumarate) crosslinked with poly(ethylene glycol)-dimethacrylate

New injectable, in situ crosslinkable biodegradable polymer composites were investigated consisting of poly(propylene fumarate) (PPF), poly(ethylene glycol)-dimethacrylate (PEG-DMA), and beta-tricalcium phosphate (beta-TCP). We examined the effects of the PEG-DMA/PPF double-bond ratio and beta-TCP content on the crosslinking characteristics of the composites including the maximum crosslinking temperature and the gel point, as well as the properties of the crosslinked composites such as the compressive strength and modulus, and the water-holding capacity. The maximum crosslinking temperature was constant averaging 39.7 degrees C for the composite formulations tested. The gel points varied from 8.0 +/- 1.0 to 12.6 +/- 2.5 min and were not affected by the relative amounts of PEG-DMA. The compressive strength at yield of PEG-DMA/PPF composites without beta-TCP increased from 5.9 +/- 1.0 to 11.2 +/- 2.2 MPa as the double-bond ratio of PEG-DMA/PPF increased from 0.38 to 1.88. An increase in compressive modulus was also observed from 30.2 +/- 3.5 to 58.4 +/- 6.2 MPa for the same range of the PEG-DMA/PPF double-bond ratio. Also, the addition of beta-TCP (33 wt%) enhanced the mechanical properties of all composites. The equilibrium water content of networks without beta-TCP increased from 21.7 +/- 0.2 to 30.6 +/- 0.2% for a double-bond ratio of PEG-DMA/PPF ranging from 0.38 to 1.88. However, the mechanical properties of the swollen composites under compression were smaller than the dry ones. These data demonstrate the feasibility of fabricating injectable biodegradable polymer composites with engineered mechanical properties for orthopedic tissue engineering.     

Bone regeneration using a microstereolithography-produced customized poly(propylene fumarate)/diethyl fumarate photopolymer 3D scaffold incorporating BMP-2 loaded PLGA microspheres

Bony defects have been three-dimensionally (3D) created in many clinical circumstances; however, many defects cannot be reconstructed because most of the current bony substitutes cannot provide the necessary exact 3D structure. Therefore, to overcome this limitation, a 3D scaffold with embedded growth factor-delivering microspheres was developed by solid free-form fabrication (SFF) technology using computer-aided design/manufacturing (CAD/CAM). In this study, BMP-2-loaded poly(DL-lactic-co-glycolic acid) (PLGA) microspheres were incorporated into a 3D scaffold that was fabricated using a microstereolithography (MSTL) system with a suspension of microspheres and a poly(propylene fumarate) (PPF)/diethyl fumarate (DEF) photopolymer. By measuring release profiles in vitro, we verified that the fabricated microsphere-containing 3D scaffold could gradually release growth factor. The effects of BMP-2 were also assessed in vitro by observing cell differentiation using MC3T3-E1 pre-osteoblasts. Finally, we confirmed that SFF scaffolds created by MSTL were superior to traditional scaffolds produced using a particulate leaching/gas foaming method. In addition, based on in vivo tests, the scaffolds that released BMP-2 promoted bone formation. Based on these results, we concluded that our 3D scaffold might be a useful tool for enhancing reconstruction quality in many complex bony defects that should be reconstructed using a customized 3D scaffold.     

In vitro degradation of polymeric networks of poly(propylene fumarate) and the crosslinking macromer poly(propylene fumarate)-diacrylate

Polymeric networks of poly(propylene fumarate) (PPF) crosslinked with poly(propylene fumarate)-diacrylate (PPF-DA) are currently being investigated as an injectable, biodegradable bone cement. This study examined the effect of crosslinking density, medium pH, and the incorporation of a beta-tricalcium phosphate (beta-TCP) filler on the in vitro degradation of PPF/PPF-DA. Cylindrical specimens were submerged in buffered saline at 37 degrees C and the change in weight, geometry, and compressive mechanical properties were monitored over a 52-week period. All formulations showed an initial increase in modulus and yield strength over the first 12 weeks, achieving maxima of 1307+/-101 and 51+/-3MPa, respectively, for the beta-TCP composite. PPF/PPF-DA networks with the lower crosslinking density demonstrated the greatest degradation with a 17% mass loss. Samples in the lower buffer pH 5.0 compared to physiological pH 7.4 did not show any differences in mass loss, but exhibited a faster decrease in the compressive strength over time. The beta-TCP composites maintained their mechanical properties at the level following their initial increase. These results show that the degradation of PPF/PPF-DA networks can be controlled by the crosslinking density, accelerated at a lower pH, and prolonged with the incorporation of the beta-TCP filler.     

In-situ preparation of poly(propylene fumarate)--hydroxyapatite composite

In-situ precipitation of hydroxyapatite (HAp) in the presence of poly(propylene fumarate) (PPF) is investigated. Amorphous calcium phosphate (ACP) precipitates in the presence of the polymer and remains in the amorphous form for a relatively long time, e.g. even after 24 h of coexistence with the mother solution. Our observations suggest that PPF interacts with the surface of the ACP particles and prevents them from transformation to crystalline hydroxyapatite. The PPF polymer seems to be more efficient in hindering the ACP to HAp transformation at higher pH conditions. From spectroscopic observations we hypothesize that the C=O bond of the PPF molecules interact with the calcium ion of the ACP particles. In case of low molecular weight PPF this interaction may lead to the incorporation of the polymer within the growing ACP particles.     

Synthesis and properties of photocross-linked poly(propylene fumarate) scaffolds

The photocross-linking of poly(propylene fumarate) (PPF) to form porous scaffolds for bone tissue engineering applications was investigated. PPF was cross-linked using the photoinitiator bis(2,4,6-trimethylbenzoyl) phenylphosphine oxide (BAPO) and exposure to 30 min of long wavelength ultraviolet (UV) light. The porous photocross-linked PPF scaffolds (6.5 mm diameter cylinders) were synthesized by including a NaCl porogen (70, 80, and 90 wt% at cross-linking) prior to photocross-linking. After UV exposure, the samples were placed in water to remove the soluble porogen, revealing the porous PPF scaffold. As porogen leaching has not been used often with cross-linked polymers, and even more rarely with photoinitiated cross-linking, a study of the efficacy of this strategy and the properties of the resulting material was required. Results show that the inclusion of a porogen does not significantly alter the photoinitiation process and the resulting scaffolds are homogeneously cross-linked throughout their diameter. It was also shown that porosity can be generally controlled by porogen content and that scaffolds synthesized with at least 80 wt% porogen possess an interconnected pore structure. Compressive mechanical testing showed scaffold strength to decrease with increasing porogen content. The strongest scaffolds with interconnected pores had an elastic modulus of 2.3+/-0.5 MPa and compressive strength at 1% yield of 0.11+/-0.02 MPa. This work has shown that a photocross-linking/porogen leaching technique is a viable method to form porous scaffolds from photoinitiated materials.     

聚丙烯延胡索酸酯的合成、交联及生物力学、体外降解检测

目的 合成新型可注射性生物降解材料聚丙烯延胡索酸酯[poly(propylene fumarate), PPF],检测其交联温度、交联时间、生物力学性能和体外降解过程。方法 合成PPF,将PPF和N-乙烯基吡咯烷酮(N-vinyl pyrrolidinone,N-VP)在过氧化苯甲酰(benzoyl peroxide,BP)催化下交联,并且加入β-磷酸三钙(β-TCP)和氯化钠(NaCl),检测交联温度、时间、生物力学性能,和PMMA骨水泥进行比较。将PPF交联后浸泡于PBS。检测体外降解时质量和力学强度的变化。结果 交联温度在41.2±2.2℃和47.5±1.7℃间,交联时间从8.1±0.8min到63.7±4.4min,PPF的压应力为2.6±0.5MPa到12.0±2.3Mpa,压缩模量为26.6±8.7MPa到252.8±57.6Mpa,体外降解后4周PPF压应力为8.4±1.6Mpa。结论 PPF有合适的交联温度、交联时间和生物力学强度,体外降解过程中力学强度可以维持4周以上,是一个有应用前景的新型可注射生物高分子聚合材料。     

Synthesis and properties of photocross-linked poly(propylene fumarate) scaffolds

The photocross-linking of poly(propylene fumarate) (PPF) to form porous scaffolds for bone tissue engineering applications was investigated. PPF was cross-linked using the photoinitiator bis(2,4,6-trimethylbenzoyl) phenylphosphine oxide (BAPO) and exposure to 30 min of long wavelength ultraviolet (UV) light. The porous photocross-linked PPF scaffolds (6.5 mm diameter cylinders) were synthesized by including a NaCl porogen (70, 80, and 90 wt% at cross-linking) prior to photocross-linking. After UV exposure, the samples were placed in water to remove the soluble porogen, revealing the porous PPF scaffold. As porogen leaching has not been used often with cross-linked polymers, and even more rarely with photoinitiated cross-linking, a study of the efficacy of this strategy and the properties of the resulting material was required. Results show that the inclusion of a porogen does not significantly alter the photoinitiation process and the resulting scaffolds are homogeneously cross-linked throughout their diameter. It was also shown that porosity can be generally controlled by porogen content and that scaffolds synthesized with at least 80 wt% porogen possess an interconnected pore structure. Compressive mechanical testing showed scaffold strength to decrease with increasing porogen content. The strongest scaffolds with interconnected pores had an elastic modulus of 2.3 ± 0.5 MPa and compressive strength at 1% yield of 0.11 ± 0.02 MPa. This work has shown that a photocross-linking/porogen leaching technique is a viable method to form porous scaffolds from photoinitiated materials.     

Synthesis and characterization of poly(propylene sulfite) from sulfur dioxide and propylene oxide using zinc derivatives as catalysts

The zinc glutarate catalyzed copolymerization of sulfur dioxide (SO₂) and propylene oxide (PO) was investigated in detail by varying temperature, time, monomer feed ratio, and PO feed per catalyst as well as by using solvents, such as PO and chloroform. An optimized copolymerization [PO]/[catalyst] = 300, and no solvent at 60°C, 40 h, [PO]/[SO₂] = 1, resulted in poly(propylene sulfite) (PPS) with high molecular weight I_n = 42 000 (I_w /I_n = 2.1) never achieved before. PPS was obtained in a yield of 66.9 g per g of catalyst (namely, 12.93 kg per mol of catalyst) and determined to consist of 90.4 mol‐% sulfite‐linkage and 9.6 mol‐% ether‐linkage. A polymer containing a large amount of ether‐linkages was additionally formed as a minor component. However, no formation of cyclic propylene sulfite as byproduct was detected. In addition, zinc hexacyanoferrate(III) was prepared and used in the copolymerization as a catalyst, but showed almost no catalytic activity.     

Enhanced bioactivity of a poly(propylene fumarate) bone graft substitute by augmentation with nano-hydroxyapatite

The bioactivity of a nano-hydroxyapatite-augmented, bioresorbable bone graft substitute made from the unsaturated polyester, poly(propylene fumarate), was analyzed by evaluating biocompatibility and osteointegration of implants placed into a rat tibial defect. Three groups of eight animals each were evaluated by grouting bone graft substitutes into 3-mm holes that were made into the anteromedial tibial metaphysis of rats. Thus, a total of 24 animals was included in this study. Two different formulations varying as to the type of hydroxyapatite were used: Group 1 - nano-hydroxyapatite, Group 2 - micron-hydroxyapatite, with a Group 3 control defect remaining unfilled. Animals of each of the three groups were sacrificed in groups of eight at postoperative week three. Histologic analysis revealed best superior biocompatibility and osteointegration of bone graft substitutes when nanohydroxyapatite was employed. At three weeks, there was more reactive new bone formation in this group when compared to the micron-hydroxyapatite group. The control group showed incomplete closure of the defect. This study suggested that nano-hydroxyapatite may improve upon the bioactivity of bone implant and repair materials. The model scaffold used in this study, poly(propylene fumarate), appeared to provide an osteoconductive pathway by which bone will grow in faster. Clinical implications of the use potential advantages of nano-hydroxyapatite on bone repair and orthopaedic implant design are discussed.     

Synthesis and water-swelling of thermo-responsive poly(ester urethane)s containing poly(epsilon-caprolactone), poly(ethylene glycol) and poly(propylene glycol)

Thermo-responsive multiblock poly(ester urethane)s comprising poly(epsilon-caprolactone) (PCL), poly(ethylene glycol) (PEG), and poly(propylene glycol) (PPG) segments were synthesized. The copolymers were characterized by GPC, NMR, FTIR, XRD, DSC and TGA. Water-swelling analysis carried out at different temperatures revealed that the bulk hydrophilicity of the copolymers could be controlled either by adjusting the composition of the copolymer or by changing the temperature of the environment. These thermo-responsive copolymer films formed highly swollen hydrogel-like materials when soaked in cold water and shrank when soaked in warm water. The changes are reversible. The mechanical properties of the copolymer films were assessed by tensile strength measurement. These copolymers were ductile when compared to PCL homopolymers. Young's modulus and the stress at break increased with increasing PCL content, whereas the strain at break increased with increasing PEG content. The results of the cytotoxicity tests based on the ISO 10993-5 protocol demonstrated that the copolymers were non-cytotoxic and could be potentially used in biomedical applications.     

Platelet adhesion on a bioresorbable poly(propylene fumarate-co-ethylene glycol) copolymer

Platelet adhesion and aggregation on poly(propylene fumarate-co-ethylene glycol), P(PF-co-EG), hydrogels was examined under both static and flow conditions. Adherent platelets were quantified under static conditions using both 111Indium oxine-labeled platelets as well as a lactate dehydrogenase, LDH, assay. The radiolabeling assay showed a significant decrease in platelet attachment on the copolymer hydrogel films relative to the poly(propylene fumarate), PPF, homopolymer. In addition, there were reductions in adhesion resulting from the increase in poly(ethylene glycol), PEG, weight percent or molecular weight. There was good agreement between both assays under static conditions for the copolymer films. Platelet surface coverage was quantified under flow conditions in a parallel plate flow chamber using the LDH assay. There was a dramatic decrease in the number of adherent platelets on the copolymers relative to glass and silicone rubber controls. All of the copolymer surfaces showed minimal aggregation with no thrombus formation or platelet spreading as assessed qualitatively using scanning electron microscopy. These results suggest that P(PF-co-EG) is a good candidate for development as a cardiovascular implant.     

Characterization of partially saturated poly(propylene fumarate) for orthopaedic application

A partially saturated linear polyester based on poly(propylene fumarate) (PPF) was synthesized for potential application in filling skeletal defects. The synthesis was carried out according to a two-step reaction scheme. Propylene glycol and fumaryl chloride were first combined to form an intermediate fumaric diester. The intermediate was then subjected to a transesterification to form the PPF-based polymer. This method allowed for production of a polymer with a number average molecular weight up to 1500 and a polydispersity index of 2.8 and below. The polymeric backbone structure was investigated through the use of FTIR and NMR. Kinetic studies of the transesterification allowed mapping of the molecular weight increase with reaction time. The final product was also characterized by thermal and solubility analysis.     

Evaluation of thermal- and photo-crosslinked biodegradable poly(propylene fumarate)-based networks

Biodegradable networks of poly(propylene fumarate) (PPF) and the crosslinking reagent poly(propylene fumarate)-diacrylate (PPF-DA) were prepared with thermal- and photo-initiator systems. Thermal-crosslinking was performed with benzoyl peroxide (BP), which is accelerated by N,N-dimethyl-p-toluidine (DMT) and enables injection and in situ polymerization. Photo-crosslinking was accomplished with bis(2,4,6-trimethylbenzoyl) phenylphosphine oxide (BAPO), which is activated by long-wavelength UV light and facilitates material processing with rapid manufacturing techniques, such as stereolithography. Networks were evaluated to assess the effects of the initiators and the PPF/PPF-DA double bond ratio on the mechanical properties. Regardless of the initiator system, the compressive properties of the PPF/PPF-DA networks increased as the double bond ratio decreased from 2 to 0.5. BAPO/UV-initiated networks were significantly stronger than those formed with BP/DMT. The compressive modulus of the photo- and thermal-crosslinked PPF/PPF-DA networks ranged from 310 +/- 25 to 1270 +/- 286 MPa and 75 +/- 8 to 332 +/- 89 MPa, respectively. The corresponding fracture strengths varied from 58 +/- 7 to 129 +/- 17 MPa and 31 +/- 13 to 105 +/- 12 MPa. The mechanical properties were not affected by the initiator concentration. Characterization of the network structures indicated that BAPO was a more efficient initiator for the crosslinking of PPF/PPF-DA, achieving a higher double bond conversion and crosslinking density than its BP counterpart. Estimated average molecular weights between crosslinks (Mc) confirmed the effects of the initiators and PPF/PPF-DA double bond ratio on the mechanical properties. This work demonstrates the capability to control the properties of PPF/PPF-DA networks as well as their versatility to be used as an injectable material or a prefabricated implant.     

Degradative properties and cytocompatibility of a mixed-mode hydrogel containing oligo[poly(ethylene glycol)fumarate] and poly(ethylene glycol)dithiol

Our laboratory is currently exploring synthetic oligo(poly(ethylene glycol)fumarate) (OPF)-based biomaterials as a means to deliver fibroblasts to promote regeneration of central/partial defects in tendons and ligaments. In order to further modulate the swelling and degradative characteristics of OPF-based hydrogels, OPF crosslinking via a radically initiated, mixed-mode reaction involving poly(ethylene glycol) (PEG)-diacrylate and PEG-dithiol was investigated. Results demonstrate that mixed-mode hydrogels containing OPF can be formed and that the presence of 20 wt.% PEG-dithiol increases swelling and decreases degradation time vs. 10 wt.% PEG-dithiol and non-thiol-containing hydrogels (20% thiol fold swelling 28.7+/-0.8; 10% thiol fold swelling 11.6+/-1.4; non-thiol 8.7+/-0.2; 20% thiol-containing hydrogels degrade within 15 days in vitro). After encapsulation, tendon/ligament fibroblasts remained largely viable over 8 days of static culture. While the presence of PEG-dithiol did not significantly affect cellularity or collagen production within the constructs over this time period, image analysis revealed that the 20% PEG-dithiol gels did appear to promote cell clustering, with greater values for aggregate area observed by day 8. These experiments suggest that mixed-mode OPF-based hydrogels may provide an interesting alternative as a cell carrier for engineering a variety of soft orthopedic tissues, particularly for applications when it is important to encourage cell-cell contact.     

Synthesis and polymerization of poly(ethylene glycol) fumarates

Fumaric esters of poly(ethylene glycol) ( 1a–d ) were prepared as macromonomers. The halfesters 1a and 1c were obtained by interaction of maleic anhydride with the monoethers of poly(ethylene glycol) ( 2a and 2b ) in the presence of 4-dimethylaminopyridine, and the diesters 1b and 1d by esterification of methyl hydrogen fumarate ( 13 ) with the monoethers of poly(ethylene glycol) ( 2a and 2b ). The macromonomers were found to homopolymerize and to copolymerize with styrene and methyl methacrylate following a radical polymerization mechanism.     

Quantitative measures of osteoinductivity of a porous poly(propylene fumarate) bone graft extender

Bioresorbable bone graft substitutes could alleviate disadvantages associated with the use of autografts, allografts, and other synthetic materials. However, little is known about the minimum autograft/extender ratio for a given material at which a sufficient osteoinductive effect is still seen. Therefore, we investigated a bioresorbable bone graft substitute made from the unsaturated polyester poly(propylene fumarate), PPF, at various mixing ratios with autograft. The bone graft extender is cross-linked in the presence of a hydroxylapatite filler and effervescent foaming agents citric acid and sodium bicarbonate. The porous bone graft extender material develops porosity in vivo by generating carbon dioxide during the effervescent reaction, resulting in foam formation and expansion with respective pore sizes of 50 to 1000 microm. In an attempt to determine how much cancellous autograft bone could be extended with the poly(propylene fumarate) material and at which ratio the autograft/extender combination remained supportive of the overall structural integrity of the repairing defect site, we studied the amount of new bone formation on implantation of the materials in 3-mm holes made in the anteromedial tibial metaphysis of Sprague-Dawley rats. The extender formulation was analyzed at high autograft/extender (75% autograft/25% extender) and low autograft/extender (25% autograft/75% extender) mixing ratios and compared with negative (extender alone) and positive (autograft alone) controls. Animals from each of the formulations were killed in groups of eight at 6 weeks postoperatively. Hence, a total of 32 animals were included in this study. Histologic analysis of the healing process revealed enhanced in vivo osteoinduction with the bone graft extender regardless of the autograft loading. Histomorphometry did not show any statistically significant difference between the high and low autograft/extender ratios. All formulations maintained implant integrity and did not provoke sustained inflammatory responses. This study suggested that the presence of even a small amount of autograft within the polymer-based bone graft extender results in significant enhancement of osteoinduction. This finding has immediate applicability to the development of bone graft extender formulations for clinical use.     

In vivo degradation of porous poly(propylene fumarate)/poly(DL-lactic-co-glycolic acid) composite scaffolds

This study investigated the in vivo degradation of poly(propylene fumarate) (PPF)/poly(DL-lactic-co-glycolic acid) (PLGA) composite scaffolds designed for controlled release of osteogenic factors. PPF/PLGA composites were implanted into 15.0mm segmental defects in the rabbit radius, harvested after 12 and 18 weeks, and analyzed using histological techniques to assess the extent of polymer degradation as well as the tissue response within the pores of the scaffolds. Polymer degradation was limited to micro-fragmentation of the scaffold at the ends and edges of the implant at both 12 and 18 weeks. The tissue within the pores of the scaffold consisted of fibrous tissue, blood vessels and some inflammatory cells. In areas where polymer breakdown was evident, an increased inflammatory response was observed. In contrast, areas of bone ingrowth into the polymer scaffold were characterized by minimal inflammatory response and polymer degradation. Our results show that minimal degradation of porous PPF occurs within 18 weeks of implantation in a rabbit model. Further, the in vivo degradation data of porous PPF/PLGA scaffolds are comparable with earlier obtained in vitro data.