Influence of Cement Replacement with Sewage Sludge Ash (SSA) on the Heat of Hydration of Cement Mortar

The amount of fly ash from the incineration of sewage sludge is increasing all over the world, and its utilization is becoming a serious environmental problem. In the study, a type of sewage sludge ash (SSA) collected directly from the municipal sewage treatment plant was used. Five levels of cement replacement (2.5%, 5%, 7.5%, 10% and 20%) and unchanged water-to-binder (w/b) ratio (0.55) were used. The purpose of the study was to evaluate the effect of sewage sludge ash (SSA) on the hydration heat process of cement mortars. The heat of the hydration of cement mortars was monitored by the isothermal calorimetric method for 7 days at 23 °C. The analysis of chemical composition and particle size distribution was performed on the tested material. The tests carried out have shown that SSA particles have irregular grain morphology and, taking into account the chemical composition consists mainly of oxides such as CaO, P₂O₅, SiO₂ and Al₂O₃. The concentration of these compounds affects the hydration process of cement mortars doped with SSA. In turn, the content of selected heavy metals in the tested ash should not pose a threat to the environment. Calorimetric studies proved that the hydration process is influenced by the presence of SSA in cement mortars. The studies showed that the rate of heat generation decreased (especially in the initial setting period) with the increasing replacement of cement by SSA, which also reduced the amount of total heat compared to the control cement mortar. With increasing mass of the replacement of cement with SSA up to 20%, the 7-day compressive strength of the mortar samples decreases.     

Performance of Cement Paste with Denitrified Fly Ash Containing NH4HSO4

The denitrification process was completed in coal-fired power plants, resulting in the fly ash containing NH₄HSO₄. When this kind of fly ash with ammonia was applied to cement and concrete, there could be phenomena such as a retarded setting time, decreased compressive strength, and volume expansion. This paper mainly investigated the influence of fly ash containing NH₄HSO₄ on the properties of fly ash cement paste, and pastes with NaHSO₄ were set as the control samples. The research on Na⁺ in cement hydration was studied. The influence of NH₄HSO₄ content in fly ash on the properties of fly ash cement paste was also investigated. It was found that NH₄⁺ could greatly affect the properties of fly ash cement paste, such as significantly reducing the fluidity, prolonging the setting time, decreasing the compressive strength, increasing the drying shrinkage, decreasing the total heat released during the hydration, and affecting the content of calcium hydroxide hydrate. Increasing the ammonia content of the denitrified fly ash would reduce fluidity, retard its setting time, increase the porosity of the cement stone, and increase the number of pores with large sizes in the fly ash cement paste. The increase of porosity and pores with large sizes in cement decreases the compressive strength and increases the drying shrinkage of the fly ash cement paste.     

Experimental Investigation on Pore Structure Characterization of Concrete Exposed to Water and Chlorides

In this paper, the pore structure characterization of concrete exposed to deionised water and 5% NaCl solution was evaluated using mercury intrusion porosity (MIP), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effects of calcium leaching, fly ash incorporation, and chloride ions on the evolution of pore structure characteristics were investigated. The results demonstrate that: (i) in ordinary concrete without any fly ash, the leaching effect of the cement products is more evident than the cement hydration effect. From the experimental data, Ca(OH)₂ is leached considerably with the increase in immersion time. The pore structure of concrete can also be affected by the formation of an oriented structure of water in concrete materials; (ii) incorporation of fly ash makes a difference for the performance of concrete submersed in solutions as the total porosity and the pore connectivity can be lower. Especially when the dosage of fly ash is up to 30%, the pores with the diameter of larger than 100 nm show significant decrease. It demonstrates that the pore properties are improved by fly ash, which enhances the resistance against the calcium leaching; (iii) chlorides have a significant impact on microstructure of concrete materials because of the chemical interactions between the chlorides and cement hydrates.     

Hydration Processes of Four-Component Binders Containing a Low Amount of Cement

Results of research on hydration of four-component binders containing very high amounts of supplementary cementitious materials were presented. The samples were composed of blended pozzolana (a mix of conventional fly ash and spent aluminosilicate catalyst), cement (about 20 wt.% in the binder) and Ca(OH)₂. Spent aluminosilicate catalyst was proposed as activating component which can improve properties of low-cement blends, while the role of Ca(OH)₂ was to enhance pozzolanic reaction. Early and later hydration periods of such blends were investigated by calorimetry, TG/DTG, FTIR and X-ray diffraction. Initial setting time as well as compressive strength were also determined. It was concluded that enhancement of reactivity and improvement of properties of fly ash–cement binders are possible by replacing a part of fly ash with more active fine-grained pozzolana and introducing additional amounts of Ca(OH)₂. The spent catalyst is mainly responsible for accelerating action during the first hours of hydration and for progress of early pozzolanic reaction. Fly ash develops its activity over time, thus synergic effect influences the later properties of composites. Samples containing blended pozzolana exhibit shorter initial setting times and higher compressive strength, as well as faster consumption of Ca(OH)₂ compared to the reference. Investigated mixtures seem to be promising as “green” binders, alternatives to cement, after optimizing their compositions or additional activating procedure.     

A New Process of Direct Zinc Oxide Production by Carbothermal Reduction of Zinc Ash

Zinc ash is a by-product of the hot-dip galvanizing process and the electrolytic zinc process, which is classified as a hazardous waste consisting predominately of zinc oxide that could be recovered as the useful main resource for ZnO preparation. In this work, in order to reduce the energy consumption of the direct reduction process and improve the resource-recovery rate. A new technology for zinc oxide production, by a carbothermal reduction of zinc ash, is proposed. This process includes two steps: high-temperature roasting of zinc ash for dechlorination and a carbothermal reduction of dechlorination ash. Zn in zinc ash is mainly presented in the form of zinc oxide (ZnO), basic zinc chloride (Zn₅(OH)₈Cl₂H₂O), and metallic zinc (Zn). Basic zinc chloride can be roasted and decomposed to reduce the chlorine content in zinc ash. The results of a chloride ion removal test show that the optimal roasting temperature is 1000 °C, with a holding time of 60 min. Under the modified conditions, the chloride content in the roasted zinc ash is reduced to 0.021 wt.%, and the dechlorination rate is more than 99.5%, which can meet the requirements of zinc oxide production. The best process conditions for zinc oxide production by carbothermic reduction are as follows: reduction temperature of 1250 °C, reduction time of 60 min, and reduction agent addition of 22 wt.%. Under the best reduction process, the purity of zinc oxide product is 99.5%, and the recovery of zinc is more than 99.25%. Needle-like zinc oxide obtained by carbothermic reduction has high purity and can replace zinc oxide produced by an indirect process.     

Circulating Fluidized Bed Fly Ash Mixed Functional Cementitious Materials: Shrinkage Compensation of f-CaO,Autoclaved Hydration Characteristics and Environmental Performance

Circulating fluidized bed (CFB) fly ash is a by-product from CFB power generation, which is hard to utilize in cement because it contains f-CaO and SO₃. This work aims to explore the mechanism of the shrinkage compensation of free-CaO (f-CaO) and the autoclaved hydration characteristics and environmental performance of CFB fly ash mixed cementitious materials (CMM). In this work, long-term volume stability of CMM is improved with the addition of CFBFA. These findings suggest that the compressive strength of sample CMM0.5 is the highest under both standard condition (67.21 MPa) and autoclaved condition (89.56 MPa). Meanwhile, the expansion rate (0.0207%) of sample CMM0.5 is the lowest, which proves the shrinkage compensation effect of f-CaO in CFBFA. The main hydration products of CMM0.5 are Ca₂SiO₄•H₂O (C-S-H) gel, CaAl₂Si₂O₇(OH)₂•H₂O (C-A-S-H) gel and Ca(OH)₂. In addition, the high polymerization degree of [Si(Al)O₄] and the densified microstructure are presented at the sample CMM0.5. The leaching results indicates that the heavy metals in CMM0.5 satisfies the WHO standards for drinking water due to physical encapsulation and charge balance. Therefore, this investigation provides a novel method of using CFB fly ash in cement.     

Strength Characteristics and Microstructure Analysis of Alkali-Activated Slag–Fly Ash Cementitious Material

Modifying the admixture of alkali-activated cementitious materials using components such as fly ash and fine sand may reduce CO₂ emissions and conserve natural resources and energy. This study adopted strength testing, scanning electron microscopy, and mercury intrusion porosimetry to investigate the influence of different admixtures on the compressive strength and flexural strength of alkali slag cementing materials and the microstructure characteristics of hardened slurry under the action of load. The flexural strength of alkali slag cement slurry and mortar was reduced by replacing slag powder with fly ash. Content of fine sand less than 20% had little effect on the strength of alkali slag cement mortar; however, when the content of fine sand exceeded 30%, the strength decreased significantly. The hydration degree at 3 d was large, and the density of slurry increased with the extension of age. Increased fly ash or fine sand content decreased the density of the slurry, and increased fly ash resulted in a large number of unhydrated fly ash particles in the cementitious materials. Addition of fine sand resulted in a large number of microcracks in the slurry, which gradually decreased with the extension of hydration age.     

Recycling of Sustainable Co-Firing Fly Ashes as an Alkali Activator for GGBS in Blended Cements

This study investigates the feasibility of co-firing fly ashes from different boilers, circulating fluidized beds (CFB) or stokers as a sustainable material in alkali activators for ground granulated blast-furnace slag (GGBS). The mixture ratio of GGBS and co-firing fly ashes is 1:1 by weight. The results indicate that only CF fly ash of CFB boilers can effectively stimulate the potential characteristics of GGBS and provide strength as an alkali activator. CF fly ash consists of CaO₃ (48.5%), SiO₂ (21.1%), Al₂O₃ (13.8%), SO₃ (10.06%), Fe₂O₃ (2.25%) and others (4.29%). SA fly ash consists of Al₂O₃ (19.7%), SiO₂ (36.3%), Fe2O3 (28.4%) and others (15.6%). SB fly ash consists of Al₂O₃ (15%), SiO₂ (25.4%), Zn (20.6%), SO₃ (10.9%), Fe₂O₃ (8.78%) and others (19.32%). The mixtures of SA fly ash and SB fly ash with GGBS, respectively, were damaged in the compressive strength test during seven days of curing. However, the built up strength of the CF fly ash and GGBS mixture can only be maintained for 7–14 days, and the compressive strength achieves 70% of that of a controlled group (cement in hardening cement paste). The strength of blended CF fly ash and GGBS started to decrease after 28 days, and the phenomenon of ettrigite was investigated due to the high levels of sulfur content. The CaO content in sustainable co-firing fly ashes must be higher than a certain percentage in reacting GGBS to ensure the strength of blended cements.     

Effect of Nano-Magnesium Oxide on the Expansion Performance and Hydration Process of Cement-Based Materials

Many scholars are concerned about the effect of nano-MgO as an expansion agent on the performance of cement-based materials at an early age, but over a long period less attention is paid to expansion stability and mechanical properties. This article examines the influence of nano-MgO on the long-term consistency, fluidity, expansion stability, hydration, and mechanical properties of 30% fly ash cement-based materials and improves research into nano-MgO as an expansion agent. Expansion performance, flexural and compressive strength, and stability after boiling and autoclave treatment were tested for specimens mixed with a 2, 4, 6, 8 and 10% cementitious material mass of nano-MgO. X-ray diffraction (XRD) and scanning electronic microscopy (SEM) were employed to study their hydration process and microstructure. The results showed that nano-MgO had an obvious effect on the consistency, fluidity and expansion performance of cement paste. After curing in water for 365 days and autoclaving thereafter, the hydration of nano-MgO was relatively complete. The volumetric expansion pressure of the magnesium hydroxide (Mg(OH)₂) crystals and the crystallization pressure generated after their continuous precipitation were the main reasons for the expansion of the slurry. Nano-MgO improved the microstructure of cement paste and significantly enhanced its long-term flexural strength and compressive strength. When the content of nano-MgO was less than 10%, the cement with 30% fly ash had good long-term stability with the potential to compensate for the shrinkage of large-volume concrete.     

Recyclability of Concrete Pavement Incorporating High Volume of Fly Ash

Recyclable concrete pavement was made from fly ash and crushed limestone sand and gravel as aggregates so that the concrete pavement could be recycled to raw materials for cement production. With the aim to use as much fly ash as possible for the sustainable development of society, while achieving adequate strength development, pavement concrete having a cement-replacement ratio of 40% by mass was experimentally investigated, focusing on the strength development at an early age. Limestone powder was added to improve the early strength; flexural strength at two days reached 3.5 MPa, the minimum strength for traffic service in Japan. The matured fly ash concrete made with a cement content of 200 kg/m³ achieved a flexural strength almost equal to that of the control concrete without fly ash. Additionally, Portland cement made from the tested fly ash concrete was tested to confirm recyclability, with the cement quality meeting the Japanese classification of ordinary Portland cement. Limestone-based recyclable fly ash concrete pavement is, thus, a preferred material in terms of sustainability.     

Hydration Characteristics of Low-Heat Cement Substituted by Fly Ash and Limestone Powder

This study proposed a new binder as an alternative to conventional cement to reduce the heat of hydration in mass concrete elements. As a main cementitious material, low-heat cement (LHC) was considered, and then fly ash (FA), modified FA (MFA) by vibrator mill, and limestone powder (LP) were used as a partial replacement of LHC. The addition of FA delayed the induction period at the hydration heat curve and the maximum heat flow value (q_max) increased compared with the LHC based binder. As the proportion and fineness of the FA increased, the induction period of the hydration heat curve was extended, and the q_max increased. The hydration production of Ca(OH)₂ was independent of the addition of FA or MFA up to an age of 7 days, beyond which the amount of Ca(OH)₂ gradually decreased owing to their pozzolanic reaction. In the case of LP being used as a supplementary cementitious material, the induction period of the hydration heat curve was reduced by comparison with the case of LHC based binder, and monocarboaluminate was observed as a hydration product. The average pore size measured at an age of 28 days was smaller for LHC with FA or MFA than for 100% LHC.     

Influence of Hydrated Lime on the Chloride-Induced Reinforcement Corrosion in Eco-Efficient Concretes Made with High-Volume Fly Ash

The main objective of this study was to analyze the influence that the addition of finely ground hydrated lime has on chloride-induced reinforcement corrosion in eco-efficient concrete made with 50% cement replacement by fly ash. Six tests were carried out: mercury intrusion porosimetry, chloride migration, accelerated chloride penetration, electrical resistivity, and corrosion rate. The results show that the addition of 10–20% of lime to fly ash concrete did not affect its resistance to chloride penetration. However, the cementitious matrix density is increased by the pozzolanic reaction between the fly ash and added lime. As a result, the porosity and the electrical resistivity improved (of the order of 10% and 40%, respectively), giving rise to a lower corrosion rate (i_CORR) of the rebars and, therefore, an increase in durability. In fact, after subjecting specimens to wetting–drying cycles in a 0.5 M sodium chloride solution for 630 days, corrosion is considered negligible in fly ash concrete with 10% or 20% lime (i_CORR less than 0.2 µA/cm²), while in fly ash concrete without lime, corrosion was low (i_CORR of the order of 0.3 µA/cm²) and in the reference concrete made with Portland cement, only the corrosion was high (i_CORR between 2 and 3 µA/cm²).     

Zinc absorption in inflammatory bowel disease

Zinc absorption was measured in 29 patients with inflammatory bowel disease and a wide spectrum of disease activity to determine its relationship to disease activity, general nutritional state, and zinc status. Patients with severe disease requiring either supplementary oral or parenteral nutrition were excluded. The mean⁶⁵ZnCl₂ absorption, in the patients, determined using a⁶⁵Zn and⁵¹Cr stool-counting test, 45±17% (SD), was significantly lower than the values, 54±16%, in 30 healthy controls,P<0.05. Low⁶⁵ZnCl₂ absorption was related to undernutrition, but not to disease activity in the absence of undernutrition or to zinc status estimated by leukocyte zinc measurements. Mean plasma zinc or leukocyte zinc concentration in patients did not differ significantly from controls, and only two patients with moderate disease had leukocyte zinc values below the 5th percentile of normal. In another group of nine patients with inflammatory bowel disease of mild-to-moderate severity and minimal nutritional impairment,⁶⁵Zn absorption from an extrinsically labeled turkey test meal was 31±10% compared to 33±7% in 17 healthy controls,P>0.1. Thus, impairment in⁶⁵ZnCl₂ absorption in the patients selected for this study was only evident in undernourished persons with moderate or severe disease activity, but biochemical evidence of zinc deficiency was uncommon, and clinical features of zinc depletion were not encountered.Supported by a grant from the Medical Research Council.     

Investigations of the Influence of Nano-Admixtures on Early Hydration and Selected Properties of Calcium Aluminate Cement Paste

In this work, the hydration of calcium aluminate cement (CAC, Al₂O₃ ≥ 70%) paste with nano admixtures (0, 0.05%, 0.1% and 0.2%) of nano-silica (NS) and carbon nano-cones (NC) when W/CAC = 0.35 was investigated. The methods of calorimetry, thermal analysis, X-ray diffraction (XRD), IR spectroscopy, and scanning electron microscopy (SEM) were used. In addition, the physical and mechanical properties of hardened cement pastes were determined after 3 days of hardening. NS was found to shorten the induction period of CAC hydration and accelerate the time of the secondary heat release effect, especially in the specimens with the highest NS content. The incorporation of NC (up to 0.2%) slows down the hydration process. After 3 days of hydration, the formation of hydration products, such as C₂AH₈, CAH₁₀, C₃AH₆ and AH₃ hydrates, was observed in CAC pastes, however, the quantitative compositions were different depending on the kind of nano admixture and its amount. SEM results obtained show differences in the effect of NS and NC on the formation of the structure of cement paste during its hardening. Significant changes in CAC paste microstructure were caused by the addition of NS and NC admixtures. Compressive strength was found to increase with the increase of NS and the optimal NS content was found to be 0.10 wt.%. The modification of the cement paste with an NS admixture results in a higher amount of hydrates, lower total porosity, and a higher amount of the smallest pores in the microstructure of the sample. NS and NC influence the hydration behaviour of CAC in different ways, which causes characteristic changes in the microstructure and properties of hardened samples.     

Research on the Working Performance and the Corresponding Mechanical Strength of Polyaluminum Sulfate Early Strength Alkali-Free Liquid Accelerator Matrix Cement

Liquid accelerating agents have the advantages of simple operation and fast construction, and have become indispensable admixtures in shotcrete. However, most liquid accelerating agents in the market at present contain alkali or fluorine, which adversely affect concrete and seriously threaten the physical and mental health of workers. Therefore, in view of the above deficiencies, it is necessary to develop a new type of alkali-free fluorine-free liquid accelerating agent. In this paper, the polyaluminum sulfate early strength alkali-free liquid accelerator is prepared using polymeric aluminum sulfate, diethanolamine, magnesium sulfate heptahydrate and nano-silica. The influence of this agent on the setting time of fresh cement paste and compressive strength of the corresponding cement mortar is determined. Thermogravimetric analysis curves, X-ray diffraction and scanning electron microscopy images are obtained to investigate the mechanism. Findings show that the initial setting time and the final setting time of cement paste are 2 min 30 s and 7 min 25 s. The compressive strengths of cement mortar cured for 1 d, 28 d and 90 d are 2.4 MPa, 52.2 MPa and 54.3 MPa respectively. Additionally, the corresponding flexural strengths are 3.4 MPa, 9.8 MPa, 11.8 MPa. When the mass rate of accelerator is 7%, the mechanical strengths of cement mortar are the highest. The additions of fly ash and blast furnace slag can affect the mechanical of cement mortar mixed with accelerator. When the mass ratio of the fly ash and blast furnace slag is 15%, the mechanical strengths of cement mortar reach the highest. Moreover, the hydration heat release rate of cement is increased by the accelerator and the corresponding time of hydration heat peak is decreased by the accelerator. The accelerator can decrease the amount of needle-like hydration products and improve the compactness. The mechanical strengths are improved by consuming a large amount of Ca(OH)₂ and forming more compact hydration products. It is recommended that the optimum dosage range of the polyaluminum sulfate early strength alkali-free liquid accelerator is 7%.     

Nano Calcium Carbonate (CaCO3) as a Reliable,Durable, and Environment-Friendly Alternative to Diminishing Fly Ash

Fly ash is widely used in the cement industry to improve the performance and durability of concrete. The future availability of fly ash, however, is a concern, as most countries are inclining towards renewable energy sources as opposed to fossil fuels. Additional concerns have been raised regarding the impact of strict environmental regulations on fly ash quality and variability. This paper, therefore, evaluates if nano calcium carbonate (nano CaCO₃) can be used as an alternative to fly ash. This paper presents comprehensive testing results (fresh, hardened, and durability) for OPC (Ordinary Portland Cement) and PLC (Portland Limestone Cement) concretes with 1% nano CaCO₃ and compares them to those for concretes with fly ash (both Class F and C). Compared to concretes with fly ash, OPC and PLC with nano CaCO₃ presented improved testing results in most cases, including later age strength, permeability, and scaling resistance. As nanotechnology in concrete is a relatively new topic, more research on the efficient use of nanotechnology, such as for proper dispersion of nano CaCO₃ in the concrete, has potential to offer increased benefits. Further, nano CaCO₃ is environmentally and economically viable, as it has the potential to be produced within the cement plant while utilizing waste CO₂ and generating economic revenue to the industry. Thus, nano CaCO₃ has the potential to serve as an alternative to fly ash in all beneficial aspects—economic, environmental, and technical.     

Durability of Mortars with Fly Ash Subject to Freezing and Thawing Cycles and Sulfate Attack

Destruction of cement composites occurs due to the alternate or simultaneous effects of aggressive media, resulting in the destruction of concrete under the influence of chemical and physical factors. This article presents the results of changes in the measurement of linear strains of samples and changes in the microstructure of cement after 30 freezing and thawing cycles and immersed in 5% sodium sulfate solution. The compressive strengths ratios were carried out at the moment when the samples were moved to the sulfate solution after 30 cycles and at the end of the study when the samples showed visual signs of damage caused by the effect of 5% Na₂SO₄. The composition of the mixtures was selected based on the Gibbs triangle covering the area up to 40% replacement of Portland cement with low and high-calcium fly ashes or their mixture. Air-entrained and non-air entrained mortars were made of OPC, in which 20%, 26.6%, and 40% of Portland cement were replaced with low and/or high-calcium fly ash. Initial, freezing and thawing cycles accelerated the destruction of non- air-entrained cement mortars immersed in 5% sodium sulfate solution. The sulfate resistance, after the preceding frost damage, decreased along with the increase in the amount of replaced fly ash in the binder. Air-entrained mortars in which 20% of cement was replaced with high-calcium fly ash showed the best resistance to the action of sodium sulfate after 30 freezing and thawing cycles.     

Experimental Investigation on Mechanical and Thermal Properties of Concrete Using Waste Materials as an Aggregate Substitution

The continuous growth of the concrete industry requires an increased quantity of cement and natural aggregates year after year, and it is responsible for a major part of the global CO₂ emissions. These aspects led to rigorous research for suitable raw materials. Taking into account that these raw materials must have a sustainable character and also a low impact on environmental pollution, the replacement of the conventional components of concrete by residual waste can lead to these targets. This paper’s aim is to analyze the density, compressive strength and the thermal conductivity of nine concrete compositions with various rates of waste: four mixes with 10%, 20%, 40% and 60% chopped PET bottles aggregates and 10% fly ash as cement partial substitution; a mix with 60% waste polystyrene of 4–8 mm and 10% fly ash; a mix with 20% waste polystyrene of 4–8 mm, 10% waste polystyrene of 0–4 mm and 10% fly ash; a mix with 50% waste polystyrene of 4–8 mm, 20% waste polystyrene of 0–4 mm and 20% fly ash two mixes with 10% fly ash and 10% and 40% waste sawdust, respectively. Using 60% PET aggregates, 60% polystyrene granules of 4–8 mm, or 20% polystyrene of 0–4 mm together with 50% polystyrene of 4–8 mm led to the obtainment of lightweight concrete, with a density lower than 2000 kg/m³. These mixes also registered the best results from a thermal conductivity point of view, after the concrete mix with 40% saw dust. Regarding compressive strength, the mix with 10% PET obtained a result very close to the reference mix, while those with 20% PET, 40% PET, 30% polystyrene, and 10% saw dust, respectively, registered values between 22 MPa and 25 MPa, values appropriate for structural uses.     

Effect of Nano-SiO2/PVA on Corrosion Behavior of Steel Rebar Embedded in High-Volume Fly Ash Mortar under Accelerated Chloride Attack

In this paper, the influence of Nano-silica (NS) and Polyvinyl alcohol (PVA) fibers on the corrosion behavior of steel rebar embedded in high-volume fly ash cement mortars under accelerated chloride attack was studied by using an impressed voltage technique. The PVA fibers used were 1.0 vol.%, and two mass fractions of cement (50 and 60 wt.%) were replaced by fly ash. Four NS mass fractions (0, 0.5, 1.0, and 1.5 wt.%) were utilized in this paper. In addition, the mono and hybrid effects of NS and PVA on the mechanical properties and water absorption of mortar were also studied. The results showed that the incorporation of PVA and nano-SiO₂ can improve the flexural and compressive strengths of high-volume fly ash mortar. Generally, the flexural and compressive strengths increased with the increase of nano-SiO₂ content. Moreover, the incorporation NS can also reduce the capillary water–absorption rate of cement mortar. The impressed voltage corrosion test indicated that the composite incorporation of nano-SiO₂ and PVA can significantly delay the deterioration process of steel bars in mortar, effectively reducing the steel rebar’s corrosion level and increasing the exposure time of the surface crack. With hybrid-incorporation 1.0 vol.% PVA and 1.0 wt.% nano-SiO₂, the steel rebar had the lowest corrosion degree, which exhibited a mass loss of 49% and increased the broken time by 71% as compared to the control mortar.     

Granite Powder vs. Fly Ash for the Sustainable Production of Air-Cured Cementitious Mortars

The partial replacement of cement in concrete with the addition of granite powder and fly ash can help to reduce the carbon dioxide (CO₂) emissions into the atmosphere associated with cement production. The aim of the article is to compare the performance of granite powder and fly ash for the sustainable production of air-cured cementitious mortars. The morphological, chemical, and granulometric properties of these additives were first compared with the properties of cement. Afterward, a series of mortars modified with the addition of granite powder and fly ash was made. The properties of the fresh mixes and the mechanical properties of the hardened composites were then tested. Finally, based on the obtained results, a cost analysis of the profitability of modifying cementitious composites with granite powder or fly ash was investigated. The obtained results allow similarities and differences between granite powder and fly ash in relation to cement to be shown. To conclude, it should be stated that both of these materials can successfully be used for the sustainable production of air-cured cementitious composites. This conclusion has a significant impact on the possibility of improving the natural environment by reducing the amount of cement production. More sustainable production of cement-based materials could enable CO₂ emissions to be decreased. The use of granite powder for the production of cementitious mortars can significantly reduce the amount of this material deposited in landfills.