Study on the Cutting Damage Mechanism of Aramid Honeycomb Based on the Progressive Damage Model

A progressive damage model for aramid honeycomb cutting was proposed to reveal its cutting damage mechanism. It established the relationship between the mesoscale failure modes and the macroscale cutting damage types of the aramid honeycomb. The proposed model addressed the material assignment problem of impregnated honeycomb by developing a material calculation method that simulates the real manufacturing process of the aramid honeycomb. Cutting experiment of aramid honeycomb specimen was conducted concerning on the cutting forces response and cutting damages, which validated that the proposed method was effective for investigating the cutting process and mechanism for the aramid honeycomb. Predicted cutting mechanism results show that: (a) cutting process of the aramid honeycomb can be divided into three stages with four characteristic states—initial state, cut-in state, cut-out state and final state; (b) cell wall bending in the cutting direction relieves the cutting force, and strong plasticity of the aramid fiber makes it hard to break, which lead to uncut fiber and burr damages; (c) using sharp tip cutting tool to reduce cutting force and bonding both top and bottom of the honeycomb to make it stiffer are beneficial to obtain good cutting quality with less damages.     

Milling Performance of CFRP Composite and Atomised Vegetable Oil as a Function of Fiber Orientation

Carbon fiber reinforced polymers (CFRPs) have found diverse applications in the automotive, space engineering, sporting goods, medical and military sectors. CFRP parts require limited machining such as detouring, milling and drilling to produce the shapes used, or for assembly purposes. Problems encountered while machining CFRP include poor tool performance, dust emission, poor part edge quality and delamination. The use of oil-based metalworking fluid could help improve the machining performance for this composite, but the resulting humidity would deteriorate the structural integrity of the parts. In this work the performance of an oil-in-water emulsion, obtained using ultrasonic atomization but no surfactant, is examined during the milling of CFRP in terms of fiber orientation and milling feed rate. The performance of wet milling is compared with that of a dry milling process. The tool displacement-fiber orientation angles (TFOA) tested are 0°, 30°, 45°, 60°, and 90°. The output responses analyzed were cutting force, delamination, and tool wear. Using atomized vegetable oil helps in significantly reducing the cutting force, tool wear, and fiber delamination as compared to the dry milling condition. The machining performance was also strongly influenced by fiber orientation. The interactions between the fiber orientation, the machining parameters and the tested vegetable oil-based fluid could help in selecting appropriate cutting parameters and thus improve the machined part quality and productivity.     

Simulation and Experimental Study on Reverse Helical Milling with the Gradual-Removal Reverse Edge Milling Cutter under Ultrasonic-Assisted Condition

As a new machining method, ultrasonic-assisted bi-direction helical milling has obvious advantages in making holes on carbon fiber-reinforced plastics (CFRP). However, cutting edges of the flat-bottomed milling cutter are easy to wear, which may cause severe defects such as burrs and tears in the outlet of the hole. In order to improve the hole-making quality of CFRP, the gradual-removal reverse edge milling cutter was proposed and designed. The finite method models of reverse helical milling CFRP with the flat-bottomed reverse edge milling cutter and the gradual-removal reverse edge milling cutter under an ultrasonic vibration were established, and the comparative cutting experiments of the two cutters were carried out. By comparing the cutting performance of the two milling cutters under the condition of ultrasonic vibration assistance, the cutting mechanism of improving the hole wall quality by the gradual-removal reverse edge milling cutter was studied. The results showed that when the reverse cumulative cutting depth reached about 60 mm, compared with the flat-bottomed reverse edge milling cutter, the gradual-removal reverse edge milling cutter transferred part of the cutting task of the peripheral edge to the end edge, and the wear of the reverse peripheral edges which directly affects the hole quality was effectively alleviated. This mechanism made the cutting state of the peripheral edge dominated by shear failure, which led to the significant improvement of the quality at the outlet of the hole.     

Method for an Effective Selection of Tools and Cutting Conditions during Precise Turning of Non-Alloy Quality Steel C45

The paper presents a constructing methodology for a modern approach to tools selection and solving the problem of assigning optimal cutting parameters for specific production conditions. The mathematical formulation determining the extreme values of the technological process optimality criteria is obtained. A system of technical and economic quality indicators for cutting tools is proposed. This system allows principles’ implementation of decentralization and interoperability “Industry 4.0” via finite element modeling of the cutting process based on solving the problem of orthogonal free cutting modeling. The proposed methodology further usage is possible by creating a standardized database on the parameters of the tool: the adhesive component of the friction cutting coefficient for processing of a specific pair of cutting and tool materials (or tool coating material) and the impacts of the cutting-edge radius on cutting efficiency of a particular material.     

The Effect of Coatings on Cutting Force in Turning of C45 Steel

This article focuses on the development of a mathematical model of a cutting force that is applicable for coated and uncoated cutting tool inserts and aims to enable more accurate calculation of the cutting force. Two common PVD coatings, AlTiN and TiAlCrN, were used. Firstly, a mathematical model of the cutting force based on the specific cutting force and cutting area is proposed. This mathematical model considers the cutting speed and coating correction factor as well as the real cutting edge geometry, i.e., it includes both the straight and rounded parts of the cutting edge. For this proposed model, material constants for C45 steel, which was machined with uncoated inserts, were obtained. Before determining an equation for a coating correction factor and implementing it into the model, experimental cutting force data for coated and uncoated inserts were compared using a paired t-test. The result was that the difference between them was statistically significant. Their percentage difference was found to be up to 4%. The correction factor equation that was obtained and implemented into the mathematical model was applied to compare the calculated and experimental data of the coated inserts, also using a paired t-test. The result was that the difference between them was insignificant. Moreover, their percentage difference was found to be up to 0.6%.     

Optimization of Machining Parameters for Milling Zirconia Ceramics by Polycrystalline Diamond Tool

Zirconia ceramics are widely used in many fields because of their excellent physical and mechanical properties. However, there are some challenges to machine zirconia ceramics with high processing efficiency. In order to optimize parameters for milling zirconia ceramics by polycrystalline diamond tool, finite element method was used to simulate machining process based on Johnson-Cook constitutive model. The effects of spindle speed, feed rate, radial and axial cutting depth on cutting force, tool flank wear and material removal rate were investigated. The results of the simulation experiment were analyzed and optimized by the response surface method. The optimal parameter combination was obtained when the spindle speed, feed rate, radial and axial cutting depth were 8000 r/min, 90.65 mm/min, 0.10 mm and 1.37 mm, respectively. Under these conditions, the cutting force was 234.81 N, the tool flank wear was 33.40 μm when the milling length was 60 mm and the material removal rate was 44.65 mm³/min.     

A Numerical Model for Predicting the Effect of Tool Nose Radius on Machining Process Performance during Orthogonal Cutting of AISI 1045 Steel

This paper presents the development of a numerical model for predicting and studying the effects of tool nose geometries and its interactions with cutting parameters during orthogonal cutting of AISI 1045 steel. The process performance characteristics studied were cutting temperature, effective stress, cutting forces and tool wear. The cutting simulations were done using the commercial DEFORM-2D ^R V 11.3 software, based on the finite element method (FEM). The cutting tool used had a round nose with various nose radii (0.01–0.9 mm), while the machining parameters tested were the feed rate (0.1–0.3 mm/rev), the cutting speed (100–500 m/min) and the rake angle (–5° to +10°). The interactions between the tool nose radius and the cutting parameters (speed, feed) were found to affect mostly the cutting stress and, slightly, the tool wear rate. These interactions did not much influence the cutting temperature, that was found to be high when the tool nose radius and/or the cutting speed were high. The maximum temperature was found to occur at the middle of the tool-chip contact length and at the interaction of nose radius and flank face of the tool. Except for some fluctuations, there was no significant difference in tool wear rate between small and large nose radius scales.     

Finite Element Analysis and Experimental Investigation of Cut Surface Formation of Magnetic Silicon Steel in Shear Cutting

Shear cutting allows for shaping materials with any length of cutting line with high efficiency and without negative thermal effects, but it causes stresses and deformations in the cutting zone of the material. This has a negative effect on the magnetic properties of the sheet in the areas of the cut edge. The main problem on production lines is to ensure appropriate control of the process so as to obtain the appropriate technological quality of the cut edge, free of not only defects in the form of burrs and shape deviations, but also the minimum deformed zone. This task is difficult due to the large number of control variables, the influence of which on the shaping of the material and the formation of the cut edge is not fully understood. The article attempts to determine the course of the cutting process and to examine the influence of control variables on the formation of the cut edge in the shear-slitting process in which the tools perform a rotary motion. For this purpose, FEM modeling, vision techniques and experimental studies were used. A 3D model of the process was developed, which enables a detailed analysis of the states of stresses, strains, displacements and fracture mechanisms of the material. The simulation results were verified using vision techniques, which were used in the work to observe the flow and cracking mechanisms of the material. Parametric analyses were performed for the process control variables. The research showed a significant influence of the cutting velocity and the clearance between the tools on the formation of the cut edge. The most homogeneous surface of the cut edge with the minimum burr height was obtained for the following parameters: rake angle α = 15–30°, horizontal clearance h_c = 0.03 mm and slitting velocity v₂ = 15 m/min. The developed results can be useful for controlling the cutting process on production lines in terms of maximum process efficiency while maintaining the appropriate technological quality of the cut edge.     

Cutting Forces during Inconel 718 Orthogonal Turn-Milling

Inconel 718 is a material often used in the aerospace and marine industries due to its properties and ability to work in harsh environments. However, its machining is difficult, and therefore methods are sought to facilitate this process. One of such methods is turn-milling. This paper presents the forces during orthogonal turn-milling of the Inconel 718 alloy. In this machining, both the side and the end edge are involved in the material removal, which causes the tool to be more loaded. The forces during turn-milling can be up to 50% higher than in the case of milling, which causes damage to the tool. Tool wear during machining has a significant impact on the values of the cutting force proportional coefficients. In the case of the tested material, it is important to take it into account when creating cutting force models.     

Experimental and Numerical Studies of Tool Wear Processes in the Nibbling Process

The work concerns an analysis of the wear mechanisms of punches in the nibbling process. The nibbling process is the multiple punching of holes or external contours using circular punches, the diameter of which is much smaller than the size of the punched shapes. Analytical, numerical and experimental studies were carried out. In the analytical solution, formulas for determining the pressures in the contact zone were developed, thus enabling a simple estimation of the designed nibbling tools. In numerical studies, the influence of the punch rounding radius on the fatigue wear was investigated. It has been shown that the change in the punch cutting edge radius from r = 0 mm to r = 0.5 mm enables a seven-fold increase in the fatigue wear resistance. It was found that the change in the punch cutting edge rounding radius has an impact on the quality of the product (the greater the radius r, the worse the technological quality of the product). In experimental studies, the abrasive wear process was primarily investigated. For this purpose, the nibbling process was tested on S235JR + AR steel sheets with tools made of NC11LV/1.2379 steel without any coating and with an AlCrTiN layer. It was found that the special AlCrTiN layer used allowed for an increase in the resistance to abrasive wear, and thus increased the service life by approx. three times. The last element of the work is an assessment of the technological quality of the product after nibbling depending on the degree and type of stamp wear (quantitative and qualitative assessment).     

Experimental and Numerical Study of Low-Velocity Impact and Tensile after Impact for CFRP Laminates Single-Lap Joints Adhesively Bonded Structure

To investigate the mechanical behavior of the single-lap joints (SLJs) adhesively bonded structure of carbon fiber reinforced polymer (CFRP) laminates under the low-velocity impact (LVI) and tensile-after impact (TAI), tests and simulations were carried out. A finite element model (FEM) was established based on the cohesive zone model (CZM) and Hashin criterion to predict the damage evolution process of adhesive film, intra- and inter-laminar of the SLJs of CFRP laminates, and its effectiveness was verified by experiments. Moreover, three different overlap lengths (20 mm, 30 mm, and 40 mm) and four different impact energies (Intact joint, 10 J, 20 J, and 30 J) are considered in the present study. Finally, the effects of different impact energies and overlap lengths on the residual strength of SLJs after impact were discussed. The results divulged that numerical results of impact and TAI processes of SLJs were in good agreement with experiment results. During the impact process, the damage of the laminates was primarily fiber and matrix tensile damage, whereas the adhesive film was damaged cohesively; the areas of damage increased with the increase of impact energy, and the normal stress of the adhesive film expanded from the edge to the middle region with the increase of impact force. The influence of LVI on SLJs adhesively bonded structures was very significant, and it is not effective to obtain a higher impact resistance by increasing the overlap length. For the tensile process, the failure mode of TAI of the SLJs was interface failure, the surplus strength of the SLJs gradually decreased with the increase of the impact energy because of the smaller overlap length, the overlap length more than 30 mm, and the low energy impact has almost no effect on the residual strength of the SLJs.     

Prediction of the Delamination at the Steel and CFRP Interface of Hybrid Composite Part

The purpose of this study was to predict the adhesive behavior of steel and carbon-fiber-reinforced plastic (CFRP) hybrid parts based on the cohesive zone model (CZM). In this study, the steel sheet and CFRP were joined by epoxy resin in the CFRP prepreg during the curing process, which could generate delamination at their interface because of the springback of steel or the thermal contraction of the CFRP. First, double cantilever beam (DCB) and end-notched flexure (ENF) tests were performed to obtain various adhesion properties such as the critical energy release rate of mode I, mode II (G_I, G_II), and critical stress (σ_max). A finite element (FE) simulation was performed to predict delamination using CZM, which was also used to describe the interfacial behavior between the steel sheet and the CFRP. Finally, a U-shape drawing test was performed for the steel/CFRP hybrid parts, and these results were compared with analytical results.     

Predictive Analytical Modeling of Thermo-Mechanical Effects in Orthogonal Machining

Factor relationships in a machining system do not work in pairs. Varying the cutting parameters, materials machined, or volumes produced will influence many machining characteristics. For this reason, we are attempting to better understand the effect of the Johnson-Cook (J-C) law of behavior on cutting temperature prediction. Thus, the objective of the present study is to investigate, experimentally and theoretically, the tool/material interactions and their effects on dust emission during orthogonal cutting. The proposed approach is built on three steps. First, we established an experimental design to analyze, experimentally, the cutting conditions effects on the cutting temperature under dry condition. The empirical model which is based on the response surface methodology was used to generate a large amount of data depending on the machining conditions. Through this step, we were able to analyze the sensitivity of the cutting temperature to different cutting parameters. It was found that cutting speed, tool tip radius, rake angle, and the interaction between the cutting speed and the rake angle explain more than 84.66% of the cutting temperature variation. The cutting temperature will be considered as a reference to validate the analytical model. Hence, a temperature prediction model is important as a second step. The modeling of orthogonal machining using the J-C plasticity model showed a good correlation between the predicted cutting temperature and that obtained by the proposed empirical model. The calculated deviations for the different cutting conditions tested are relatively acceptable (with a less than 10% error). Finally, the established analytical model was then applied to the machining processes in order to optimize the cutting parameters and, at the same time, minimize the generated dust. The evaluation of the dust generation revealed that the dust emission is closely related to the variation of the cutting temperature. We also noticed that the dust generation can indicate different phenomena of fine and ultrafine particles generation during the cutting process, related to the heat source or temperature during orthogonal machining. Finally, the effective strategy to limit dust emissions at the source is to avoid the critical temperature zone. For this purpose, the two-sided values can be seen as combinations to limit dust emissions at the source.     

Increasing the Efficiency of Food Material Cutting during Inclined and Shear Movements of Knife

Mathematical models for predicting the resistance forces that are developed during the inclined and sliding cutting of food materials have been developed. The dependence of the actual cutting angle on the angle of inclination and sliding speed of the cutting edge at various sharpening angles have been investigated. For the inclined cutting mode, the dependence of the useful resistance force on the cutting speed has been determined at various angles of inclination of the cutting edge and designed sharpening angles. For the sliding cutting mode, the dependence of the useful resistance force on the feeding speed has been demonstrated at various sliding speed values and designed knife sharpening angles. The dependence of the transformed dimensionless sharpness of the knife on the angle of inclination of the cutting edge and the sliding speed has been established for different constructional sharpness values of the knife. The results of the study indicate that the useful resistance force is significantly reduced during the inclined and sliding cutting processes when compared with the normal cutting process, and a change in the pattern of fiber destruction, which significantly increases the cutting efficiency of cutting tools, is obtained.     

Analysis on the Mechanical Behavior of Flexible Screens

Recently, flexible organic light-emitting devices (OLEDs) have become more and more popular. However, the force distribution and deformation are very complex during the bending process, and it is difficult to analyze the stress and strain by theoretical analysis and direct experiment. In this paper, finite element analysis of the bending model for the flexible screen was performed. For common U-shaped bending, it was shown that the maximum Mises stress increases rapidly as the bending radius decreases, and the redistribution of the tensile zone and the compression zone should be the key to the layer material selection. The results were verified by an imaging experiment. Further, a water-drop-shaped bending mode was analyzed to reduce the risk of structure failure.     

Determination of the Tool–Chip Contact Length for the Cutting Processes

The thermomechanical interaction of the tool with the chip in the most loaded secondary cutting zone depends on the contact length of the tool rake face with the chip. Experimental studies of the dependency of the contact length on the cutting speed, the undeformed chip thickness, and the tool rake angle, performed by the optical method, are used for comparison with the contact length obtained by the FE modeling of the orthogonal cutting process. To determine the parameters of the constitutive Johnson–Cook equation, which serves as a material model of the FE cutting model that has a predominant influence on the contact length, a software-implemented algorithm was developed. This algorithm is based on determining the generalized parameters of the constitutive equation through finding the intersection of these parameter sets. The plurality intersection of the parameter sets of the constitutive equation is determined by means of the design of experiments and refined by subsequent multiple iterations. The comparison of the contact length values, obtained by simulating the cutting process using the generalized parameters of the constitutive equation as a material model with their experimental values, does not exceed 12% for a wide range of cutting speeds and depths of cut, as well as for the tool rake angle.     

Wear Mechanism of Multilayer Coated Carbide Cutting Tool in the Milling Process of AISI 4340 under Cryogenic Environment

Cryogenic technique is the use of a cryogenic medium as a coolant in machining operations. Commonly used cryogens are liquid nitrogen (LN2) and carbon dioxide (CO₂) because of their low cost and non-harmful environmental impact. In this study, the effects of machining conditions and parameters on the wear mechanism were analysed in the milling process of AISI 4340 steel (32 HRC) under cryogenic conditions using a multilayer coated carbide cutting tool (TiAlN/AlCrN). A field emission scanning electron microscope with energy-dispersive X-ray analysis was used to examine the wear mechanisms comprehensively. At low machining parameters, abrasion and adhesion were the major wear mechanisms which occurred on the rake face. Machining at high machining parameters caused the removal of the coating material on the rake face due to the high temperature and cutting force generated during the cutting process. In addition, it was found that continuously adhered material on the rake face would lead to crater wear. Furthermore, the phenomenon of oxidation was also observed when machining at high cutting speed, which resulted in diffusion wear and increase in the crater wear. Based on the relationship between the cutting force and cutting temperature, it can be concluded that these machining outputs are significant in affecting the progression of tool wear rate, and tool wear mechanism in the machining of AISI 4340 alloy steel.     

CFRP Origami Metamaterial with Tunable Buckling Loads: A Numerical Study

Origami has played an increasingly central role in designing a broad range of novel structures due to its simple concept and its lightweight and extraordinary mechanical properties. Nonetheless, most of the research focuses on mechanical responses by using homogeneous materials and limited studies involving buckling loads. In this study, we have designed a carbon fiber reinforced plastic (CFRP) origami metamaterial based on the classical Miura sheet and composite material. The finite element (FE) modelling process’s accuracy is first proved by utilizing a CFRP plate that has an analytical solution of the buckling load. Based on the validated FE modelling process, we then thoroughly study the buckling resistance ability of the proposed CFRP origami metamaterial numerically by varying the folding angle, layer order, and material properties, finding that the buckling loads can be tuned to as large as approximately 2.5 times for mode 5 by altering the folding angle from 10° to 130°. With the identical rate of increase, the shear modulus has a more significant influence on the buckling load than Young’s modulus. Outcomes reported reveal that tunable buckling loads can be achieved in two ways, i.e., origami technique and the CFRP material with fruitful design freedoms. This study provides an easy way of merely adjusting and controlling the buckling load of lightweight structures for practical engineering.     

Method of Designing a Friction-Based Wedge Anchorage System for High-Strength CFRP Plates

The cables of high-strength carbon fiber reinforced polymer (CFRP) plates are starting to be applied to large spatial structures. However, their main anchorage systems rely on the adhesive force, which entails risks to their integrity resulting from aging of the binding agent. In this study, a friction-based wedge anchorage system was designed for CFRP plates. The working mechanism of the proposed anchorage system was explored both theoretically and experimentally. The anti-slip mechanism and condition of CFRP plates were formulated so that the equivalent frictional angle of the contact surface between a CFRP plate and wedges must not be smaller than the sum of the dip angle of the wedge external conical surface and the frictional angle between the wedges and barrel. An analysis of the stress distribution in the anchorage zone of the CFRP plate was conducted using the Tsai-Wu failure criterion, which concluded that the compressive stresses should be reduced on the section closer to the load-bearing end of the anchorage system. Furthermore, the anchorage efficiency coefficient was proposed, which depends on stress concentration coefficients, plate thickness, length of anchorage zone, dip angle of wedge external conical surface, and its frictional angle. Then, it was determined that the minimum length of an anchorage zone for the CFRP plates with various specifications should be at least 49 times larger than the CFRP thickness. A finite element analysis and static tensile tests on six specimens were carried out. The experimental results revealed that the anchorage efficiency coefficient of the optimized anchor reached 97.9%.     

Study on Milling Force and Surface Quality during Slot Milling of Plain-Woven CFRP with PCD Tools

Carbon-fiber-reinforced polymers (CFRPs) have been widely used in many industrial fields, such as automobile, aerospace and so on, because of their excellent mechanical properties. However, due to their anisotropy and inhomogeneity, machining CFRPs is a great challenge. In this paper, the slot milling of a plain-woven CFRP with PCD tools is carried out, and the effects of cutting parameters and tool rake angle on cutting force and surface roughness are studied. The results show that the 4° rake angle PCD tool has smaller cutting force than the 0° rake angle PCD tool, but the effect of rake angle on surface roughness is not significant. The concept of equivalent cutting area is introduced to study the variation law of cutting force and surface roughness. It is found that the cutting force and surface roughness increase with the increase in equivalent cutting area, and decrease with the decrease in equivalent cutting area. The removal mechanism of surface materials under different equivalent cutting areas is different, which leads to the difference in surface roughness. Finally, the causes of delamination on the top layer after milling are explained.