首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
The properties of blended cement containing 0%, 20%, and 50% iron tailing powder (ITP) at 20 °C and 60 °C were investigated by determining the hydration heat, microstructure, and compressive strength. The addition of ITP decreases the exothermic rate and cumulative hydration heat of blended cement at 20 °C. The high temperature increases the hydration rate and leads to the hydration heat of blended cement containing 20% ITP higher than that of Portland cement. Increasing the amount of ITP decreases the non-evaporable water content and Ca(OH)2 content as well as compressive strength at both of the two studied temperatures. The addition of ITP coarsens the early-age pore structure but improves the later-age pore structure at 20 °C. The high temperature significantly improves the early-age properties of blended cement containing ITP, but it is detrimental to the later-age properties development. The reaction of ITP is limited even at high temperature. The large ITP particles bond poorly with surrounding hydration products under early high-temperature curing condition. The properties of blended cement containing a large amount of ITP are much poorer at high temperature.  相似文献   

2.
Growing concerns on global industrial greenhouse gas emissions have boosted research for developing alternative, less CO2 intensive binders for partial to complete replacement of ordinary Portland cement (OPC) clinker. Unlike slag and pozzolanic siliceous low-Ca class F fly ashes, the Ca- and S-rich class C ashes, particularly these formed in circulating fluidised bed combustion (CFBC) boilers, are typically not considered as viable cementitious materials for blending with or substituting the OPC. We studied the physical, chemical-mineralogical characteristics of the mechanically activated Ca-rich CFBC fly ash pastes and mortars with high volume OPC substitution rates to find potential alternatives for OPC in building materials and composites. Our findings indicate that compressive strength of pastes and mortars made with partial to complete replacement of the mechanically activated CFBC ash to OPC is comparable to OPC concrete, showing compared to OPC pastes reduction in compressive strength only by <10% at 50% and <20% at 75% replacement rates. Our results show that mechanically activated Ca-rich CFBC fly ash can be successfully used as an alternative CSA-cement type binder.  相似文献   

3.
Circulating fluidized bed (CFB) fly ash is a by-product from CFB power generation, which is hard to utilize in cement because it contains f-CaO and SO3. This work aims to explore the mechanism of the shrinkage compensation of free-CaO (f-CaO) and the autoclaved hydration characteristics and environmental performance of CFB fly ash mixed cementitious materials (CMM). In this work, long-term volume stability of CMM is improved with the addition of CFBFA. These findings suggest that the compressive strength of sample CMM0.5 is the highest under both standard condition (67.21 MPa) and autoclaved condition (89.56 MPa). Meanwhile, the expansion rate (0.0207%) of sample CMM0.5 is the lowest, which proves the shrinkage compensation effect of f-CaO in CFBFA. The main hydration products of CMM0.5 are Ca2SiO4•H2O (C-S-H) gel, CaAl2Si2O7(OH)2•H2O (C-A-S-H) gel and Ca(OH)2. In addition, the high polymerization degree of [Si(Al)O4] and the densified microstructure are presented at the sample CMM0.5. The leaching results indicates that the heavy metals in CMM0.5 satisfies the WHO standards for drinking water due to physical encapsulation and charge balance. Therefore, this investigation provides a novel method of using CFB fly ash in cement.  相似文献   

4.
Featured Application In this paper, blended cements are proposed as an effective means of meeting the needs of mitigating climatic change. This proposal is a two-pronged strategy, i.e., durable and sustainable. The pozzolanic reaction of four binders is assessed, which is related to an alkali–silica reaction (ASR). Thanks to the findings made here, mix-design optimization can be performed. AbstractAlkali–silica reaction (ASR) is a swelling reaction that occurs in concrete structures over time between the reactive amorphous siliceous aggregate particles and the hydroxyl ions of the hardened concrete pore solution. The aim of this paper is to assess the effect of pozzolanic Portland cements on the alkali–silica reaction (ASR) evaluated from two different points of view: (i) alkali-silica reaction (ASR) abatement and (ii) climatic change mitigation by clinker reduction, i.e., by depleting its emissions. Open porosity, SEM microscopy, compressive strength and ASR-expansion measurements were performed in mortars made with silica fume, siliceous coal fly ash, natural pozzolan and blast-furnace slag. The main contributions are as follows: (i) the higher the content of reactive silica in the pozzolanic material, the greater the ASR inhibition level; (ii) silica fume and coal fly ash are the best Portland cement constituents for ASR mitigation.  相似文献   

5.
This study proposed a new binder as an alternative to conventional cement to reduce the heat of hydration in mass concrete elements. As a main cementitious material, low-heat cement (LHC) was considered, and then fly ash (FA), modified FA (MFA) by vibrator mill, and limestone powder (LP) were used as a partial replacement of LHC. The addition of FA delayed the induction period at the hydration heat curve and the maximum heat flow value (qmax) increased compared with the LHC based binder. As the proportion and fineness of the FA increased, the induction period of the hydration heat curve was extended, and the qmax increased. The hydration production of Ca(OH)2 was independent of the addition of FA or MFA up to an age of 7 days, beyond which the amount of Ca(OH)2 gradually decreased owing to their pozzolanic reaction. In the case of LP being used as a supplementary cementitious material, the induction period of the hydration heat curve was reduced by comparison with the case of LHC based binder, and monocarboaluminate was observed as a hydration product. The average pore size measured at an age of 28 days was smaller for LHC with FA or MFA than for 100% LHC.  相似文献   

6.
The denitrification process was completed in coal-fired power plants, resulting in the fly ash containing NH4HSO4. When this kind of fly ash with ammonia was applied to cement and concrete, there could be phenomena such as a retarded setting time, decreased compressive strength, and volume expansion. This paper mainly investigated the influence of fly ash containing NH4HSO4 on the properties of fly ash cement paste, and pastes with NaHSO4 were set as the control samples. The research on Na+ in cement hydration was studied. The influence of NH4HSO4 content in fly ash on the properties of fly ash cement paste was also investigated. It was found that NH4+ could greatly affect the properties of fly ash cement paste, such as significantly reducing the fluidity, prolonging the setting time, decreasing the compressive strength, increasing the drying shrinkage, decreasing the total heat released during the hydration, and affecting the content of calcium hydroxide hydrate. Increasing the ammonia content of the denitrified fly ash would reduce fluidity, retard its setting time, increase the porosity of the cement stone, and increase the number of pores with large sizes in the fly ash cement paste. The increase of porosity and pores with large sizes in cement decreases the compressive strength and increases the drying shrinkage of the fly ash cement paste.  相似文献   

7.
Increasing utilization of secondary raw materials and alternative fuels results in increasing contents of metals in cements. Zinc is one of these elements. It comes to cement with secondary raw materials such as slag or fly ash or by the utilization of used tires as an alternative fuel. Zinc ions significantly prolong the hydration process in cement. This work deals with the influence of zinc ions in the form of very poorly soluble ZnO salt and easily soluble ZnCl2 and Zn(NO3)2 on the hydration of cement blended with fly ash. Zinc was dosed in the range of 0.05%, 0.1%, 0.5% and 1% of cement weight. The effect of zinc on hydration was monitored by isothermal and isoperibolic calorimetry. A 15% addition of fly ash to cement mainly causes further retardation of hydration reactions due to the reactions of fly ash particles with Ca2+ ions from cement. The strongest effect on the hydration retardation from all investigated compounds showed in ZnO as it dissolves very slowly. On the contrary, for the dosage of 1% of zinc in the form of ZnCl2 significant acceleration of hydration occurred. In this work, a synergistic effect on the prolongation of hydration with a combination of cement, zinc and fly ash was demonstrated. The lengths of induction periods were assessed from detected calorimetric curves and from these lengths the curves were gained by fitting with the exponential function. Final products were next analyzed using X-ray diffraction.  相似文献   

8.
Climate change has become trending news due to its serious impacts on Earth. Initiatives are being taken to lessen the impact of climate change and mitigate it. Among the different initiatives, researchers are aiming to find suitable alternatives for cement. This study is a humble effort to effectively utilize industrial- and agricultural-waste-based pozzolanic materials in concrete to make it economical and environmentally friendly. For this purpose, a ternary blend of binders (i.e., cement, fly ash, and rice husk ash) was employed in concrete. Different variables such as the quantity of different binders, fine and coarse aggregates, water, superplasticizer, and the age of the samples were considered to study their influence on the compressive strength of the ternary blended concrete using gene expression programming (GEP) and artificial neural networking (ANN). The performance of these two models was evaluated using R2, RMSE, and a comparison of regression slopes. It was observed that the GEP model with 100 chromosomes, a head size of 10, and five genes resulted in an optimum GEP model, as apparent from its high R2 value of 0.80 and 0.70 in the TR and TS phase, respectively. However, the ANN model performed better than the GEP model, as evident from its higher R2 value of 0.94 and 0.88 in the TR and TS phase, respectively. Similarly, lower values of RMSE and MAE were observed for the ANN model in comparison to the GEP model. The regression slope analysis revealed that the predicted values obtained from the ANN model were in good agreement with the experimental values, as shown by its higher R2 value (0.89) compared with that of the GEP model (R2 = 0.80). Subsequently, parametric analysis of the ANN model revealed that the addition of pozzolanic materials enhanced the compressive strength of the ternary blended concrete samples. Additionally, we observed that the compressive strength of the ternary blended concrete samples increased rapidly within the first 28 days of casting.  相似文献   

9.
This article presents the physical and mechanical properties of geopolymer concrete with lightweight artificial aggregate. A research experiment where the influence of fly ash–slag mix (FA-S), as part of a pozzolanic additive, on the properties of geopolymers was carried out and the most favorable molar concentration of sodium hydroxide solution was determined. The values of three variables of the examined properties of the geopolymer lightweight concrete (GLC) were adopted: X1—the content of the pozzolanic additives with fly ash + flay ash–slag (FA + FA-S) mix: 200, 400 and 600 kg/m3; X2—the total amount of FA-S in the pozzolanic additives: 0, 50 and 100%; X3—the molarity of the activator NaOH: (8, 10 and 12 M). In order to increase the adhesion of the lightweight artificial aggregate to the geopolymer matrix, the impregnation of the NaOH solution was used. Based on the obtained results for the GLC’s compressive strength after 28 days, water absorption, dry and saturated density and thermal conductivity index, it was found that the most favorable parameters were obtained with 400 kg/m3 of pozzolanic additives (with 50% FA-S and 50% FA) and 10 NaOH molarity. Changes in the activator’s concentration from 8 to 10 M improved the compressive strength by 54% (for a pozzolana content of 200 kg/m3) and by 26% (for a pozzolana content of 600 kg/m3). The increase in the content of pozzolanic additives from 200 to 400 kg/m3 resulted in a decrease in water absorption from 23% to 18%. The highest conductivity coefficient, equal to 0.463 W/m·K, was determined, where the largest amount of pozzolanic additives and the least lightweight aggregate were added. The structural tests used scanning electron microscopy analysis, and the beneficial effect of impregnating the artificial aggregate with NaOH solution was proved. It resulted in a compact interfacial transition zone (ITZ) between the lightweight aggregate and the geopolymer matrix because of the chemical composition (e.g., silica amount), the silica content and the alkali presoaking process.  相似文献   

10.
The influence of four naturally occurring mineral additives (zeolite, diatomite, trass and bentonite) on the hydration and properties of cement pastes and mortars was investigated. The materials change the phase composition, heat of hydration (determined by calorimetry) and mechanical properties of composites. After 28 days, the amount of Ca(OH)2 was reduced by up to 23% and up to 35% more C-S-H was formed, as proved by TG measurements. Differences were observed in the kinetics of heat release, especially for 25% of the addition. In the calorimetric curves, an additional exothermic effect is observed, related to the alteration in the hydration of C3A in cement. From the point of view of beneficial influence on mechanical properties of mortars, the additives could be ranked as follows: bentonite < diatomite, zeolite < trass after 2 days and bentonite < diatomite < trass < zeolite after 28 days of curing. The highest compressive strength (58.5 MPa) was observed for the sample with a 10% addition of zeolite. Zeolite, trass, bentonite and diatomite are all pozzolanic materials; however, their activity varies to an extent due to the differences in their specific surface area and the content of the amorphous phase, responsible for the pozzolanic reaction.  相似文献   

11.
In recent years, partial replacement of cement with bagasse ash has been given attention for construction application due to its pozzolanic characteristics. Sugarcane bagasse ash and fine bagasse particles are abundant byproducts of the sugar industries and are disposed of in landfills. Our study presents the effect of burning bagasse at different temperatures (300 °C and 600 °C) on the compressive strength and physical properties of bagasse ash-blended mortars. Experimental results have revealed that bagasse produced more amorphous silica with very low carbon contents when it was burned at 600 °C/2 h. The compressive strength of mortar was improved when 5% bagasse ash replaced ordinary portland cement (OPC) at early curing ages. The addition of 10% bagasse ash cement also increased the compressive strength of mortars at 14 and 28 days of curing. However, none of the bagasse ash-blended portland pozzolana cement (PPC) mortars have shown improvement on compressive strength with the addition of bagasse ash. Characterization of bagasse ash was done using XRD, DTA-TGA, SEM, and atomic absorption spectrometry. Moreover, durability of mortars was checked by measuring water absorption and apparent porosity for bagasse ash-blended mortars.  相似文献   

12.
Supplementary cementitious materials (SCMs) and chemical additives (CA) are incorporated to modify the properties of concrete. In this paper, SCMs such as fly ash (FA), ground granulated blast furnace slag (GGBS), silica fume (SF), rice husk ash (RHA), sugarcane bagasse ash (SBA), and tire-derived fuel ash (TDFA) admixed concretes are reviewed. FA (25–30%), GGBS (50–55%), RHA (15–20%), and SBA (15%) are safely used to replace Portland cement. FA requires activation, while GGBS has undergone in situ activation, with other alkalis present in it. The reactive silica in RHA and SBA readily reacts with free Ca(OH)2 in cement matrix, which produces the secondary C-S-H gel and gives strength to the concrete. SF addition involves both physical contribution and chemical action in concrete. TDFA contains 25–30% SiO2 and 30–35% CaO, and is considered a suitable secondary pozzolanic material. In this review, special emphasis is given to the various chemical additives and their role in protecting rebar from corrosion. Specialized concrete for novel applications, namely self-curing, self-healing, superhydrophobic, electromagnetic (EM) wave shielding and self-temperature adjusting concretes, are also discussed.  相似文献   

13.
Many scholars are concerned about the effect of nano-MgO as an expansion agent on the performance of cement-based materials at an early age, but over a long period less attention is paid to expansion stability and mechanical properties. This article examines the influence of nano-MgO on the long-term consistency, fluidity, expansion stability, hydration, and mechanical properties of 30% fly ash cement-based materials and improves research into nano-MgO as an expansion agent. Expansion performance, flexural and compressive strength, and stability after boiling and autoclave treatment were tested for specimens mixed with a 2, 4, 6, 8 and 10% cementitious material mass of nano-MgO. X-ray diffraction (XRD) and scanning electronic microscopy (SEM) were employed to study their hydration process and microstructure. The results showed that nano-MgO had an obvious effect on the consistency, fluidity and expansion performance of cement paste. After curing in water for 365 days and autoclaving thereafter, the hydration of nano-MgO was relatively complete. The volumetric expansion pressure of the magnesium hydroxide (Mg(OH)2) crystals and the crystallization pressure generated after their continuous precipitation were the main reasons for the expansion of the slurry. Nano-MgO improved the microstructure of cement paste and significantly enhanced its long-term flexural strength and compressive strength. When the content of nano-MgO was less than 10%, the cement with 30% fly ash had good long-term stability with the potential to compensate for the shrinkage of large-volume concrete.  相似文献   

14.
This study investigates the feasibility of co-firing fly ashes from different boilers, circulating fluidized beds (CFB) or stokers as a sustainable material in alkali activators for ground granulated blast-furnace slag (GGBS). The mixture ratio of GGBS and co-firing fly ashes is 1:1 by weight. The results indicate that only CF fly ash of CFB boilers can effectively stimulate the potential characteristics of GGBS and provide strength as an alkali activator. CF fly ash consists of CaO3 (48.5%), SiO2 (21.1%), Al2O3 (13.8%), SO3 (10.06%), Fe2O3 (2.25%) and others (4.29%). SA fly ash consists of Al2O3 (19.7%), SiO2 (36.3%), Fe2O3 (28.4%) and others (15.6%). SB fly ash consists of Al2O3 (15%), SiO2 (25.4%), Zn (20.6%), SO3 (10.9%), Fe2O3 (8.78%) and others (19.32%). The mixtures of SA fly ash and SB fly ash with GGBS, respectively, were damaged in the compressive strength test during seven days of curing. However, the built up strength of the CF fly ash and GGBS mixture can only be maintained for 7–14 days, and the compressive strength achieves 70% of that of a controlled group (cement in hardening cement paste). The strength of blended CF fly ash and GGBS started to decrease after 28 days, and the phenomenon of ettrigite was investigated due to the high levels of sulfur content. The CaO content in sustainable co-firing fly ashes must be higher than a certain percentage in reacting GGBS to ensure the strength of blended cements.  相似文献   

15.
In this paper, the pore structure characterization of concrete exposed to deionised water and 5% NaCl solution was evaluated using mercury intrusion porosity (MIP), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The effects of calcium leaching, fly ash incorporation, and chloride ions on the evolution of pore structure characteristics were investigated. The results demonstrate that: (i) in ordinary concrete without any fly ash, the leaching effect of the cement products is more evident than the cement hydration effect. From the experimental data, Ca(OH)2 is leached considerably with the increase in immersion time. The pore structure of concrete can also be affected by the formation of an oriented structure of water in concrete materials; (ii) incorporation of fly ash makes a difference for the performance of concrete submersed in solutions as the total porosity and the pore connectivity can be lower. Especially when the dosage of fly ash is up to 30%, the pores with the diameter of larger than 100 nm show significant decrease. It demonstrates that the pore properties are improved by fly ash, which enhances the resistance against the calcium leaching; (iii) chlorides have a significant impact on microstructure of concrete materials because of the chemical interactions between the chlorides and cement hydrates.  相似文献   

16.
This paper investigates the effect of curing regimes (standard and steam curing) on the mechanical strength, hydration, and microstructure of ecological ultrahigh-performance concrete (EUHPC). The flowability, compressive strength, flexural strength, hydration, porosity, pore size distribution, and microstructure of UHPC with different contents of supplementary materials (silica fume, fly ash, and ground granulated blast furnace slag) were assessed. The test results showed that the compressive strength of EUHPC under steam curing was increased considerably compared to that under standard curing, while the flexural strength was mildly decreased. The steam curing could decrease the porosity of EUHPC, which ranged between 7% and 9% for standard curing, and between 3.5% and 5% for steam curing. The aperture of EUHPC was below 20 nm, mainly located in the range of 10 nm to 20 nm under standard curing, while it was less than 10 nm for steam curing. C–S–H gel was produced under steam curing, while unhydrated fly ash, mineral powder, and Ca(OH)2 crystal were observed in the amorphous C–S–H gel. The microstructure of EUHPC under steam curing was denser than that under standard curing, and the interfacial transition zones under both curing regimes were compact.  相似文献   

17.
The application of granulated copper slag (GCS) to partially replace cement is limited due to its low pozzolanic activity. In this paper, reconstituted granulated copper slag (RGCS) was obtained by adding alumina oxide (Al2O3) to liquid copper slag. Blended cement pastes were formulated by a partial substitute for ordinary Portland cement (OPC) with the RGCS (30 wt%). The pozzolanic activity, mechanical development, and the microstructure were characterized. The results show that 5–10 wt% Al2O3 contributes to the increase in magnetite precipitation in RGCS. The addition of Al2O3 alleviates the inhibition of C3S by RGCS and accelerates the dissociation of RGCS active molecules, thus increasing the exothermic rate and cumulative heat release of the blended cement pastes, which are the highest in the CSA10 paste with the highest Al2O3 content (10 wt%) in RGCS. The unconfined compressive strength (UCS) values of blended cement mortar with 10 wt% Al2O3 added to RGCS reach 27.3, 47.4, and 51.3 MPa after curing for 7, 28 and 90 d, respectively, which are the highest than other blended cement mortars, and even exceed that of OPC mortar at 90 d of curing. The pozzolanic activity of RGCS is enhanced with the increase in Al2O3 addition, as evidenced by more portlandite being consumed in the CSA10 paste, forming more C-S-H (II) gel with a higher Ca/Si ratio, and a more compact microstructure with fewer pores than other pastes. This work provided a novel, feasible, and clean way to enhance the pozzolanic activity of GCS when it was used as a supplementary cementitious material.  相似文献   

18.
At present, reducing carbon emissions is an urgent problem that needs to be solved in the cement industry. This study used three mineral admixtures materials: limestone powder (0–10%), metakaolin (0–15%), and fly ash (0–30%). Binary, ternary, and quaternary pastes were prepared, and the specimens’ workability, compressive strength, ultrasonic pulse speed, surface resistivity, and the heat of hydration were studied; X-ray diffraction and attenuated total reflection Fourier transform infrared tests were conducted. In addition, the influence of supplementary cementitious materials on the compressive strength and durability of the blended paste and the sustainable development of the quaternary-blended paste was analyzed. The experimental results are summarized as follows: (1) metakaolin can reduce the workability of cement paste; (2) the addition of alternative materials can promote cement hydration and help improve long-term compressive strength; (3) surface resistivity tests show that adding alternative materials can increase the value of surface resistivity; (4) the quaternary-blended paste can greatly reduce the accumulated heat of hydration; (5) increasing the amount of supplementary cementitious materials can effectively reduce carbon emissions compared with pure cement paste. In summary, the quaternary-blended paste has great advantages in terms of durability and sustainability and has good development prospects.  相似文献   

19.
Liquid accelerating agents have the advantages of simple operation and fast construction, and have become indispensable admixtures in shotcrete. However, most liquid accelerating agents in the market at present contain alkali or fluorine, which adversely affect concrete and seriously threaten the physical and mental health of workers. Therefore, in view of the above deficiencies, it is necessary to develop a new type of alkali-free fluorine-free liquid accelerating agent. In this paper, the polyaluminum sulfate early strength alkali-free liquid accelerator is prepared using polymeric aluminum sulfate, diethanolamine, magnesium sulfate heptahydrate and nano-silica. The influence of this agent on the setting time of fresh cement paste and compressive strength of the corresponding cement mortar is determined. Thermogravimetric analysis curves, X-ray diffraction and scanning electron microscopy images are obtained to investigate the mechanism. Findings show that the initial setting time and the final setting time of cement paste are 2 min 30 s and 7 min 25 s. The compressive strengths of cement mortar cured for 1 d, 28 d and 90 d are 2.4 MPa, 52.2 MPa and 54.3 MPa respectively. Additionally, the corresponding flexural strengths are 3.4 MPa, 9.8 MPa, 11.8 MPa. When the mass rate of accelerator is 7%, the mechanical strengths of cement mortar are the highest. The additions of fly ash and blast furnace slag can affect the mechanical of cement mortar mixed with accelerator. When the mass ratio of the fly ash and blast furnace slag is 15%, the mechanical strengths of cement mortar reach the highest. Moreover, the hydration heat release rate of cement is increased by the accelerator and the corresponding time of hydration heat peak is decreased by the accelerator. The accelerator can decrease the amount of needle-like hydration products and improve the compactness. The mechanical strengths are improved by consuming a large amount of Ca(OH)2 and forming more compact hydration products. It is recommended that the optimum dosage range of the polyaluminum sulfate early strength alkali-free liquid accelerator is 7%.  相似文献   

20.
The use of nanomaterials to enhance the physical and mechanical properties and durability of cement materials in their hardened state has been studied for a long time in many investigations. In comparison, fewer studies focus on nanomaterials’ influence on the fresh state when the cement reaction starts. In addition, if we consider ternary blended cement (as those used for applications in marine environments), this has been rarely studied. Severe stresses in the marine environment require high durability, which is achieved by using pozzolanic additions, to the detriment of a rapid achievement of the properties. The addition of nanomaterials could contribute to increasing the durability and also accelerating the setting of the concrete. In this work, we performed a systematic and comparative study on the influence of adding graphene oxide (GO), nanosilica (NS), and microfibrillated cellulose (MFC) during the setting mechanisms of cement (CEM V/A suitable for concrete subjected to external attacks in marine environments) blended with fly ash and slag. Cement hardening was examined through setting time and rheology within mini-slump tests. The effect of nanoadditives on the cement hydration was analysed by heat flow calorimetry to evaluate the acceleration potential. Exploring the three nanoadditives on the same formulation, we could establish that the retention of mixing water significantly decreased workability for MFC. In contrast, NS increases the hydration of cement particles, acting as nucleation nodes and promoting supplementary cement hydrates (pozzolanic reactions) and accelerating setting time. Finally, GO showed a reduction in workability. We also investigated the dosage effects on mechanical behaviour at an early age and discovered an improvement even at low GO (0.006%) and NS (3%) dosages. We have also analysed the dosage effects on mechanical behaviour at an early age.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号