Ultrafast imaging of tissue ablation by a XeCl excimer laser in saline.

To determine the temporal evolution of laser induced tissue ablation, arterial wall specimens with either hard calcified or fatty plaques and normal tissue were irradiated in a 0.9% saline solution using a XeCl excimer laser (wavelength 308 nm, energy fluence 7 J/cm2, pulse width 30 ns) through a 600 microns fused silica fiber pointing perpendicular either at a 0.5 mm distance or in direct contact to the vascular surface. Radiation of a pulsed dye laser (wavelength 580 nm) was used to illuminate the tissue surface. The ablation process and the arising bubble above the tissue surface were recorded with a CCD camera attached to a computer based image-processing system. Spherical cavitation bubbles and small tissue particles emerging from the irradiated area have been recorded. The volume of this bubble increased faster for calcified plaques than for normal tissue.     

Autofluorescence spectroscopy using a XeCl excimer laser system for simultaneous plaque ablation and fluorescence excitation

Laser–induced fluorescence may be used to guide laser ablation of atherosclerotic lesions. This study was performed to evaluate arterial autofluorescence spectroscopy in vitro using a single XeCl excimer laser (308 nm) for simultaneous tissue ablation and fluorescence excitation. The laser beam was coupled to a 600-μm silica fiber transmitting 40–50 mJ/mm² per pulse. The fluorescence radiation emanating retrogradely from the fiber was collected by a concave mirror for spectroscopic analysis over a range of 321–657 nm. The arterial media (n = 26), lipid plaques (n = 26), and calcified lesions (n = 27) of aortic specimens from ten human cadavers were investigated in air, saline, and blood. Whereas the spectrum of calcified lesions changed with the surrounding optical medium, the other spectra remained constant. In air and blood, the spectra of arterial media, lipid plaques, and calcified lesions could be differentiated qualitatively and quantitatively (P < 0.0001). In saline, there was no clearcut spectroscopic difference between lipid plaques and calcified lesions. However, normal arterial media and atherosclerotic lesions (lipid plaques plus calcified lesions) could still be discriminated. Thus spectroscopy and plaque ablation can be combined using a single XeCl excimer laser. These encouraging results should stimulate further studies to determine the potential use of this approach to guide laser angioplasty in humans. © 1994 Wiley-Liss, Inc.     

Characteristics of 308 nm excimer laser activated arterial tissue photoemission under ablative and non-ablative conditions

The present study was designed to assess the characteristics of tissue photoemission obtained from normal and atherosclerotic segments of human postmortem femoral arteries by 308 nm excimer laser irradiation of 60 ns pulsewidth. Three ablative (20, 30, and 40 mJ/pulse) and three non-ablative (2.5, 5, and 10 mJ/pulse) energy fluences were employed. Both the activating laser pulses and the induced photoemission were guided simultaneously over one and the same 1,000 micron core optical fiber that was positioned in direct tissue contact perpendicular to the vascular surface. The spectral lineshape of normal arterial and noncalcified atherosclerotic structures was characterized by a broad-continuum, double-peak emission of relevant intensity between wavelengths of 360 and 500 nm, with the most prominent emission in the range of 400-415 (407 nm peak) and 430-445 nm (437 nm peak). Fibrous and lipid atherosclerotic lesions, however, exhibited a significantly reduced intensity at 437 nm compared to normal artery layers (P less than 0.001), expressed as a 407/437 nm ratio of 1.321 +/- 0.075 for fibrous and 1.392 +/- 0.104 for lipid lesions. Normal artery components presented with approximately equal intensity at both emission peaks (407/437 nm ratio: intima, 1.054 +/- 0.033; media, 1.024 +/- 0.019; adventitia, 0.976 +/- 0.021). Comparison of spectral lineshape obtained under various energy fluences within a group of noncalcified tissues disclosed no substantial difference using the 407/437 nm ratio (P greater than 0.05). In contrast, calcified lesions revealed high-intensity multiple-line (397, 442, 461, and 528 nm) emission spectra under ablative energy fluences, whereas a low-intensity broad-continuum, single-peak spectrum resulted from irradiation beyond the ablation threshold. Thus, these findings suggest fluorescence phenomena for broad-continuum spectra, and plasma emission for multiple-line spectra as an underlying photodynamic process. Regardless of the activating energy fluence, spectral analysis of 308 nm activated photoemission provides accurate information about the laser target under standardized in vitro conditions. It is demonstrated that direct contact ablation and simultaneous spectral imaging of the target tissue via the same optical fiber is feasible.(ABSTRACT TRUNCATED AT 400 WORDS)     

Dependence of the XeCl laser cut rate of plaque on the degree of calcification, laser fluence, and optical pulse duration

A XeCl laser with an optical pulse duration of 35 ns was used to determine the cut depth per laser pulse of postmortem human aorta as a function of laser fluence for four main categories of plaque development. The data indicate that the cut depth per pulse progressively decreases as the degree of calcification increases even at very high (100 mJ/mm2) laser fluences. A comparison was made between the XeCl laser cut rate data obtained using the 35-ns duration laser pulses to data obtained using 200-ns duration pulses for each of the four plaque types. As the degree of tissue calcification increased higher XeCl laser fluences were required for the long pulse case to achieve the same cut depth per pulse as that observed using the shorter pulse duration.     

XeCl laser ablation of atherosclerotic aorta: optical properties and energy pathways.

The energetics of 308-nm excimer laser irradiation of human aorta were studied. The heat generation that occurred during laser irradiation of atherosclerotic aorta equaled the absorbed laser energy minus the fraction of energy for escaping fluorescence (0.8-1.6%) and photochemical decomposition (2%). The absorbed laser energy is equal to the total delivered light energy minus the energy lost as specular reflectance (2.4%, air/tissue) and diffuse reflectance (11.5-15.5%). Overall, about 79-83.5% of the delivered light energy was converted to heat. We conclude that the mechanism of XeCl laser ablation of soft tissue involves thermal overheating of the irradiated volume with subsequent explosive vaporization. The optical properties of normal wall of human aorta and fibrous plaque, both native and denatured were determined. The light scattering was significant and sufficient to cause a subsurface fluence (J/cm2) in native aorta that equaled 1.8 times the broad-beam radiant exposure, phi o (2.7 phi o for denatured aorta). An optical fiber must have a diameter of at least 800 microns to achieve a maximum light penetration (approximately 200 microns for phi o/e) in the aorta along the central axis of the beam.     

In vitro evaluation of ablation parameters of normal and fibrous aorta using smooth excimer laser coronary angioplasty

A modified exeimer laser energy delivery system was used to irradiate 100 segments of normal and fibrous aorta in vitro. The laser beam was scanned into 8 fiber bundles consisting of 50 fibers each resulting in a reduction of the applied pulse energy. The total repetition rate was increased to 150 Hz in order to keep the repetition rate per fiber bundle close to 20 Hz and to minimize thermal injury. The results demonstrate that effective ablation (etch rate per 8 pulses > 2.0 μm) occurred at an energy fluency of 50 mJ/mm² in both normal and fibrous aorta. Tissue damage (carbonization, tissue separation, fissures, cracks, and vacuolization) was in a range of 100 ± 28 to 152 ± 30 μm for normal aorta and in a range of 57 ± 35 to 110 ± 39 μm for fibrous aorta. We conclude that effective ablation of normal and fibrous human aorta can be achieved by the application of smooth excimer laser coronary angioplasty. This improvement of excimer laser technology may result in a reduction of shock wave- and cavitation-induced damage leading to a reduction of tissue injury. However, this awaits further in vitro and in vivo confirmation. © 1993 Wiley-Liss, Inc.     

Noncontact tissue ablation by holmium:YSGG laser pulses in blood

To assess the feasibility of intra-arterial tissue ablation by Holmium:YSGG laser pulses (2.1 microns) in a noncontact mode, the transmission of the laser pulses through saline and blood was measured. The temporal interaction between the 500 microseconds laser pulse and saline at the fiber tip was investigated with time-resolved flash photography. The penetration depth in blood, and saline depended on the fiber output energy. In blood at 37 degrees C, the penetration depth varied from 1.2 to 2.1 mm for intensities of 3.1 to 12.4 J/mm2 per pulse, respectively, whereas its theoretical value for water is 0.33 mm, which is based on the measured absorption coefficient of 3.0 +/- 0.1/mm. The large penetration depth was due to the development of a transparent vapour cavity around the fiber tip. In saline, its maximum length was 4.7 mm. Its maximum width was 2.8 mm. The lifetime of the cavity was 450 microseconds. In blood, ablation of porcine aorta was feasible at a distance of 3 mm. Large fissures observed in adjacent tissue are likely to be caused by the expansion of the vapour cavity. We conclude that, due to a "Moses effect in the microsecond region," Holmium:YSGG tissue ablation is possible through at least 2.7 mm of blood.     

Mechanism of CW Nd:YAG laser recanalization with modified fiber tips: influence of temperature and axial force on tissue penetration in vitro

Modified fiber tips are used for laser angioplasty of totally occluded peripheral arteries. It has not been established, however, to what extent the mechanism of action of various laser probes is optical, thermal, or mechanical. We examined transparant contact probes (hemispherical contact probes and ball-shaped fibers) and metal laser probes, coupled to a continuous-wave Nd-YAG laser. By using homogeneous thick porcine fatty tissue samples submerged in blood plasma, tissue penetration was measured in relation to the temperature of the probe and the axial force exerted on the tissue. By using 15 W, 1 s laser pulses, the surface of transparent contact probes had to be first contaminated by carbonized tissue particles to achieve tissue penetration. Penetration increased from 1 to 10 mm per pulse when axial force increased from 20 to 100 g. Metal probes had to be sufficiently insulated from the liquid environment by water vapour entrapped in a denatured protein layer to exceed the threshold temperature of 225 degrees C for tissue penetration. When axial force increased from 20 to 80 g at 10 W continuous exposure, the velocity of tissue penetration increased in the range from 1 to 4 mm/s. Tissue penetration by modified fiber tips is attributed to both remodeling and vaporization of tissue. With transparent contact probes, tissue is heated partly by direct light absorption and partly by a hot probe surface. Axially directed force is necessary to displace lateral non-ablated tissue and to overcome mechanical resistance. We conclude that mechanical dilation due to axial catherization force (Dotter effect) contributes substantially to tissue penetration by transparent contact probes.     

Excimer laser ablation of fibrocartilage: an in vitro and in vivo study

To date, lasers have found only limited applications in orthopedics. We employed a 308 nm XeCl excimer laser for ablation of fibrocartilage, in order to investigate the feasibility of excimer laser assisted meniscectomy. Experiments were conducted both in vitro and in vivo. For the in vitro study, human menisci, obtained during surgery and autopsy, were irradiated via a 600 microns core fiber at radiant exposures ranging between 20 mj/mm2 and 80 mj/mm2, at 20 Hz. Ablation rate measurements and histological analysis of the samples were performed. The ablation rates were found to range from 3 microns/pulse to 100 microns/pulse depending on the radiant exposure and/or the applied pressure on the fiber delivery system. Thermographic analysis was also performed during pulsed excimer as well as CW Nd:Yag and CW CO2 laser irradiation. Temperatures were lower for excimer laser (Tmax less than 65 degrees) than CW ND: Yag (Tmax less than 210 degrees) or CW CO2 (Tmax less than 202 degrees) laser. For the in vitro study, medial meniscectomy was performed in 15 rabbits with the excimer laser and a CW Nd:Yag laser in the right and left knee respectively. Excimer laser irradiation was performed at 70 mj/mm2. Nd:Yag irradiation was performed via a 600 microns core fiber at power outputs between 20 to 40 W for 10 and 20 seconds duration. The healing response to injury was investigated by histological analysis of the menisci after 1 day, 1, 2, 4, and 8 weeks following the laser procedure. Excimer laser treated menisci showed less inflammatory reaction and noticeable repair with minimal inflammatory response.(ABSTRACT TRUNCATED AT 250 WORDS)     

Effect of blood upon the selective ablation of atherosclerotic plaque with a pulsed dye laser

Laser angioplasty systems with laser energy preferentially absorbed by atherosclerotic plaque may offer a safe method of plaque removal. This study evaluated the effect of blood upon selective energy absorption using a pulsed dye laser at 480 nm. Intra-arterial laser irradiation of normal rabbit femoral arteries demonstrated a perforation threshold energy with blood perfusion of 13.1 mJ per pulse compared to 87.9 mJ with saline (P less than .0001), indicating a deleterious effect in the presence of blood. An adverse effect upon arterial healing at 3 days was noted in sheep following intra-arterial irradiation during blood but not saline perfusion. Normal and atherosclerotic human aorta ablation thresholds differed significantly (P less than .0002) under saline (plaque: 20 mJ and normal: 120 mJ) but the difference under blood (plaque: 5 mJ and normal: 20 mJ) was not significant. We conclude that absorption of laser energy by blood can reduce the effect of differential absorption by endogenous chromophores in normal and pathologic vascular tissues and, therefore, removal of blood may be a prerequisite for selective ablation of atherosclerotic plaques.     

Fluorescence guided excimer laser ablation of intervertebral discs in vitro

Laser induced fluorescence of intervertebral discs was investigated in this study for the first time in order to develop a fluorescence guided percutaneous excimer laser discectomy. For this purpose 35 human cadaveric intervetebral discs from level L1 to L5 were irradiated with a 308 nm XeCl excimer laser with a 60 nsec pulse width at 10, 20 and 30 mj/mm2. Laser light was transmitted over a 1000 microns core optical fiber. Fluorescence emitted from the irradiated tissue was transmitted back over the same fiber over a semireflective mirror to another optical fiber, coupled into a spectrograph and O-SMA optical simultaneous multichannel spectral analyzer system. The spectral lineshape of both the annulus fibrosus and the nucleus pulposus was characterized by a broadband emission between 320 nm and 616 nm with 3 peak emissions at 358, 423 and 457 nm. Relative intensities were calculated by forming two ratios of the peak intensities of the three peaks (R1 = I 423/I 358; R2 = I 423/I 457). Statistical analysis of both ratios revealed a highly significant discrimination between annulus fibrosus and nucleus pulposus (P less than 0.001). Under penetrating conditions multiple recorded spectra showed the spectral profile of subsequently ablated nucleus and annulus. The results of this study demonstrate that discrimination between annulus fibrosus and nucleus pulposus by excimer laser-induced fluorescence is feasible under laboratory conditions. Fluorescence spectroscopy could possibly be developed into a valuable guiding system for percutaneous laser discectomy.     

Effect of the ArF excimer laser on human enamel.

Human enamel surface was irradiated with ArF excimer laser and examined under light microscopy and scanning electron microscopy (SEM). Enamel surface was irradiated at three different areas with different energy fluences. It is demonstrated that the ArF excimer laser causes ablation of the calcified hard enamel tissue. Ablation curves were measured. There was no significant difference found in the etch depth between the three different areas of enamel surface. The morphology of the irradiated areas seen under the SEM was found to be dependent on energy fluence. It changed with increase in energy fluence from being etched to forming a smooth, fused, glaze-like surface and then at very high energy fluences producing a rough surface. The influence of the laser irradiation was confined to the irradiated area only, with no visible heat damage to the surroundings. These results suggest that excimer laser could be applied in a controlled and defined manner for tooth enamel treatments in dentistry.     

Recanalization of arterial occlusions with a lensed fiber and a holmium:YAG laser.

Laser recanalization of totally occluded swine iliac arteries was performed to assess the safety and efficacy of a lensed fiber laser angioplasty system with a holmium:YAG (2.1 microns) laser. Silica lenses of 1.0 mm, 1.3 mm, and 1.5 mm in diameter attached to the distal end of a 300-microns diameter silica fiber delivered fluences of 79.5 J/cm2, 31.4 J/cm2, and 25.5 J/cm2, respectively. The pulse duration of the laser was 250 microseconds and the repetition rate was 4 Hz. The mean length of the total occlusions was 5.3 +/- 2.0 cm (range 0.5 cm to 8.0 cm). Successful recanalization was obtained in 16/16 lesions without angiographic vessel perforation. Angiographically significant residual stenoses (greater than 50%) remained in every case following successful laser recanalization. Histologically there was minimal evidence of thermal or acoustic tissue injury; however, in 4 of 16 arteries there was evidence of deep arterial dissection following laser recanalization. We conclude that this lensed fiber coupled with a holmium:YAG laser is a safe and effective method for crossing total occlusions in the relatively straight iliac arteries of this animal model.     

Ultraviolet laser ablation of skin: healing studies and a thermal model

We have followed the course of healing of incisions made with the krypton-fluoride excimer laser. Incisions were made in guinea pig skin, in vivo, under identical conditions of irradiation. The progressive healing of these incisions was followed over the course of 3 weeks. We noted excellent healing with re-epithelialization, and the re-formation of collagen fibers with minimal fibrosis. We present a simple thermal model for ablation of tissue by a short pulse of strongly absorbed laser radiation.     

Partial ablation of porcine stratum corneum by argon-fluoride excimer laser to enhance transdermal drug permeability

To enhance skin permeability to medicine, the argon–fluoride excimer laser (ArF laser) was used to partially ablate the stratum corneum. Skin permeability to dextran (20 kDa) was studied in the Yucatan micropig skin in vitro. The cumulative amount of dextran permeating across the full-thickness skin was not detected for 30 h in the unirradiated skin; we obtained up to 90.5 g/cm² in laser-irradiated skin. In the case where the total laser energy was kept constant at 7.1 J/cm², permeability was mainly influenced by laser fluence rather than laser pulses. Many granular structures of about 2 m were found on the stratum corneum surface of ablated skin. Size and density of these structures were changed according to irradiation conditions. Skin permeability may be estimated by these structural changes. Our partial stratum corneum ablation by ArF laser could be suitable for transdermal drug delivery.     

Comparison of thermal tissue effects induced by contact application of fiber guided laser systems

BACKGROUND AND OBJECTIVES: Laser light of various wavelengths is being used for surgical procedures in otolaryngology. Apart from well-known fiber guided laser systems such as Nd:YAG- and Ho:YAG-lasers, newly developed diode-laser systems of different wavelengths have recently become popular in surgery. In order to compare the effects of fiber guided laser light with respect to their induced tissue effects, these laser systems have been studied and compared under reproducible test conditions. STUDY DESIGN/MATERIALS AND METHODS: The laser fibers of four common medical laser systems (Ho:YAG- (lambda = 2,080 nm), Nd:YAG- (lambda = 1,064 nm), and diode-laser (lambda = 830 and 940 nm)) were fixed to a computer controlled stepper motor. The laser light was applied in contact mode onto ex vivo muscle tissue, using identical power settings and a reproducible application procedure (application velocity, application angle) under constant conditions (temperature of tissue and volume). The size of the thermal effects on the tissue (e.g., coagulation, ablation, and carbonization zones) were measured and photographed via optical microscopy. RESULTS: Depending on the laser wavelength used, the experimental results proved different degrees of tissue responses. Nd:YAG- and diode-lasers provided for only low coagulation effects in the depth of the tissue, but produced severe carbonization at the surface. Ho:YAG-laser light revealed the highest ablation capabilities of the lasers investigated in addition to large coagulation zones which were of larger extent than those produced by Nd:YAG- and diode-laser light. CONCLUSIONS: Contact treatment by Ho:YAG-laser light might provide for a precise and effective tissue reduction in a bloodless manner because of its high ablation and coagulation capabilities, especially if large volumes are treated and structures beneath are non-critical. In comparison, Nd:YAG- and diode-laser treatment in contact application showed low thermal tissue effects (i.e., coagulation) in the depth, resulting from a high power loss caused by the development of large carbonization zones at the surface of the tissue. Therefore, the degree of blood-perfusion and the capability of vessel-closure induced by these lasers should be taken into account. The presented investigation also revealed that in contact mode, the tested laser systems produced tissue effects, which were highly different from those already described for applications in non-contact mode. Physicians who are performing laser treatments in close boundaries must be aware that changing from non-contact to contact mode in laser application greatly influences the resulting tissue effects.     

Formation of pressure waves during in vitro excimer laser irradiation in whole blood and the effect of dilution with contrast media and saline

Pressure waves during excimer laser ablation of vascular tissue may be responsible for complications of coronary excimer laser angioplasty. In this experimental study, pressure waves were measured during excimer laser irradiation in blood and contrast media using a polyvinilidenefluoride hydrophone. At a distance of 4 mm lateral to the tip of a 1.7 mm multifiber laser catheter, excimer laser irradiation in blood resulted in a linear increase of peak pressures from 1,365 ± 165 kPa at 30 mJ/mm² to 2,866 ± 404 kPa at 60 mJ/mm². In contrast media, peak pressure increased from 3,172 ± 573 kPa (30 mJ/mm²) to 5,763 ± 467 kPa (60 mJ/mm²). Contrast media and saline were added to blood. At a concentration of 60% contrast in blood, a 3.4 fold increase of peak pressures was documented as compared to pure blood. Further increase of the concentration did not result in higher pressure waves. Concentrations of saline in blood of 90% and 96% reduced the peak pressures by 16% and >50%, respectively, as compared to pure blood. © 1994 Wiley-Liss, Inc.