Automated system for release studies of salicylic acid based on a SIA method

The aim of this work was to describe a fully automated system for the in vitro release testing of semisolid dosage forms based on SIA technique. The system was tested for monitoring release profiles of different ointments containing 3% of salicylic acid (Belosalic, Diprosalic, Triamcinolone S). The native fluorescence of salicylic acid was used for fluorimetric detection. Phosphate buffer pH 7.4 was the receptor medium; samples were taken at 10 min intervals during 6 h of the release test; and each test was followed by calibration with five standard solutions. The linear calibration range was 0.05–10 μg ml⁻¹ (r = 0.9996, six standards); the maximal SIA sample throughput for this system was 120 h⁻¹, sample volume being 50 μl and flow rate 50 μl s⁻¹. The detection limit for salicylic acid was 0.01 μg ml⁻¹.     

Development and validation of a novel LC non-derivatization method for the determination of amikacin in pharmaceuticals based on evaporative light scattering detection

A novel method for the direct determination of the aminoglycoside antibiotic amikacin and its precursor component kanamycin was developed and validated, based on reversed phase LC with evaporative light scattering detector (ELSD). ELSD response to amikacin was found to be enhanced by: (a) use of ion-pairing acidic reagents of increased molecular mass, (b) increase of mobile phase volatility and (c) decrease of peak width and asymmetry (obtained by controlling the mobile phase acidity and/or ratio of organic solvent to water). Utilizing a Thermo Hypersil BetaBasic C₁₈ column, the selected optimized mobile phase was water–methanol (60:40, v/v), containing 3.0 ml l⁻¹ nonafluoropentanoic acid (18.2 mM) (isocratic elution with flow rate of 1.0 ml min⁻¹). ELSD experimental parameters were: nitrogen pressure 3.5 bar, evaporation temperature 50 °C, and gain 11. Amikacin was eluted at 8.6 min and kanamycin at 10.4 min with a resolution of 1.5. Logarithmic calibration curves were obtained from 7 to 77 μg ml⁻¹ (r > 0.9995) for amikacin and 8 to 105 μg ml⁻¹ (r > 0.998) for kanamycin, with a LOD equal to 2.2 and 2.5 μg ml⁻¹, respectively.

In amikacin sulfate pharmaceutical raw materials, the simultaneous determination of sulfate (t_R = 2.3 min, LOD = 1.8 μg ml⁻¹, range 5–40 μg ml⁻¹, %R.S.D. = 1.1, r > 0.9997), kanamycin and amikacin was feasible. No significant difference was found between the results of the developed LC–ELSD method and those of reference methods, while the mean recovery of kanamycin from spiked samples (0.5%, w/w) was 97.3% (%R.S.D. ≤ 2.0, n = 6). Further, the developed method was applied for the determination of amikacin in pharmaceutical formulations (injection solutions) without any interference from the matrix (recovery from spiked samples ranged from 95.6 to 103.8%).     

Determination of catecholamines by flow-injection analysis and high-performance liquid chromatography with chemiluminescence detection

A chemiluminescence (CL) detection of catecholamines [norepinephrine (NE), epinephrine (E), dopamine (DA) and l-dopa (LD)] is described for the flow-injection (FI) and high-performance liquid chromatographic (HPLC) determination of these compounds. The detection method is based on the inhibition effect of catecholamines (CAs) on the CL reaction of luminol with iodine in the alkaline medium. The proposed FI method allows the determination of CAs in pharmaceutical preparations for the purpose of drug quality control. The calibration curves show good linearity in the concentration range of: 1.1–20.0 μg l⁻¹ (NE), 0.5–5.0 μg l⁻¹ (E), 0.6–9.0 μg l⁻¹ (DA) and 0.6–10.0 μg l⁻¹ (LD). The limits of detection (defined as a signal-to-noise ratio of 3) are: 0.34 μg l⁻¹ (NE), 0.15 μg l⁻¹ (E) and 0.18 μg l⁻¹ (DA, LD). The HPLC procedure was successfully applied for the determination of catecholamines (NE, E, DA) in human urine after solid-phase extraction (SPE). In a simple run time CAs can be determined in 20 min. The chromatographic linear ranges are: 5.0–72.0 μg l⁻¹ (NE), 5.0–48.0 μg l⁻¹ (E) and 5.0–96.0 μg l⁻¹ (DA). The limits of detection for three urinary CAs are: 0.71 μg l⁻¹ (NE), 0.26 μg l⁻¹ (E) and 0.73 μg l⁻¹ (DA).     

Evaluation of micronucleus induction of sand dust storm fine particles (PM(2.5)) in human blood lymphocytes

Sand dust storms are common phenomena in the arid and semi-arid regions. Previous studies have demonstrated that the airborne air fine particulate matter (PM_2.5, particulates with an aerodynamic diameter ≤2.5 μm) and its extracts can induce human genetic damage of lymphocytes such as micronucleus formation, chromosomal aberration and so on. However, little is known about the health risks associated with sand dust storm PM_2.5 and its extracts. The aim of the present study is to investigate the micronucleus induction of sand dust storm PM_2.5 (include its organic and inorganic extract) from two different towns on human lymphocytes. The samples of normal PM_2.5 and sand dust storm PM_2.5 were collected in Wuwei (Gansu Province) and Baotou (Inner Mongolia), China. The cytochalasin-B cytokinesis-block test was employed and the cells were treated with 0, 33, 100, 300 μg ml⁻¹ sand dust storm PM_2.5 or normal ambient air PM_2.5 suspension (physiological saline as solvent control), or inorganic extract (0, 75, 150, 300 μg ml⁻¹, physiological saline as solvent control) or organic extract (0, 20, 40, 80 μg ml⁻¹, DMSO as solvent control) at the beginning of the cell culture. Both sand dust storm and normal PM_2.5 and their extract treatment cultures revealed an increase in the frequency of micronucleus. With the increase of treatment concentrations the frequency of micronucleus increased and the nuclear division index (NDI) values declined in a dose–response manner (P < 0.01). In the same concentrates, the frequency of micronucleus of normal ambient air PM_2.5 and its extract were significant higher than those of sand dust storm PM_2.5 (P < 0.01) except the treatment of Wuwei sample at higher doses, the treatment of inorganic extract of PM_2.5 at the highest dose (300 μg ml⁻¹) and the treatment of organic extract of PM_2.5 at the higher dose (40 and 80 μg ml⁻¹) either in Baotou or in Wuwei (P > 0.05). The toxicity of sand dust storm PM_2.5 and its extract at high dose is very potent. The frequency of micronucleus of normal PM_2.5 (include its organic extract) from Baotou were higher than those of Wuwei especially in low and middle dose (P < 0.05), but the treatment results of sand dust storm PM_2.5 (include its all extract) was not significantly different between the towns (P > 0.05).     

Flow injection spectrophotometric determination of Al in hemodialysis solutions

A flow analysis (FA) system with spectrophotometric detection for Al determination in hemodialysis solutions was developed. The method was based on the reaction of Al with eriochrome cyanine R (ECR). The complex formed associated with cetyltrimethylammonium bromide (CTAB) — a cationic surfactant, which showed enough sensitivity to execute the direct analyte determination. All interferences were eliminated with the matrix matching calibration. The system presented the following analytic parameters: sensitivity (m) of 8.10 × 10⁻⁴ L μg⁻¹, limit of detection (LOD) of 3.24 μg L⁻¹ (3σ), linear correlation coefficient of 0.9966 and linear range response from 10.8 to 650 μg L⁻¹. The accuracy of the proposed method was checked by comparison with electrothermal atomic absorption spectrometry (ET-AAS) method. There were no differences among the results obtained from both methods, at a confidence level of 95% (paired t-test). Recovery tests were also made, values obtained were from 90.4 to 109 of recovery for Al-spiked samples.     

Simultaneous separation and determination of active components in Cordyceps sinensis and Cordyceps militarris by LC/ESI-MS

A simple and rapid isocratic LC/MS coupled with electrospray ionization (ESI) method for simultaneous separation and determination of adenine, hypoxanthine, adenosine and cordycepin in Cordyceps sinensis (Cs) and its substitutes was developed. 2-Chloroadenosine was used as internal standard for this assay. The optimum separation for these analytes was achieved using the mixture of water, methanol and formic acid (85:14:1, v/v/v) as a mobile phase and a 2.0×150 mm Shimadzu VP-ODS column. Selective ion monitoring (SIM) mode ([M+H]⁺ at m/z 136, 137, 268, 252 and 302) was used for quantitative analysis of above four active components. The regression equations were liner in the range of 1.4–140.0 μg ml⁻¹ for adenine, 0.6–117.5 μg ml⁻¹ for hypoxanthine, 0.5–128.5 μg ml⁻¹ for adenosine and 0.5–131.5 μg ml⁻¹ for cordycepin. The limits of quantitation (LOQ) and detection (LOD) were, respectively 1.4 and 0.5 μg ml⁻¹ for adenine, 0.6 and 0.2 μg ml⁻¹ for hypoxanthine, 0.5 and 0.1 μg ml⁻¹ for adenosine and cordycepin. The recoveries of four constituents were from 93.5 to 107.0%. The nucleoside contents of various types of natural Cs and its substitutes were determined and compared with this developed method.     

Microcalorimetric investigation of the toxic action of ammonium ferric(III) sulfate on the metabolic activity of pure microbes

A series of calorimetric experiments were performed to investigate toxic action of ammonium ferric sulfate (AFS) on Bacillus subtilis, Pseudomonas putida and Candida humicola. The power–time curves of micro-organism metabolism were obtained, and the action of them by addition of AFS was studied. C. humicola, B. subtilis and P. putida were inhibited completely when the concentrations were up to 320.0, 160.0 and 160.0 μg mL⁻¹, respectively. The relationships between growth rate constant (k) and doses of AFS were approximately linear for three microbes, P. putida for 10.0–160.0 μg mL⁻¹ (R = −0.9746), B. subtilis for 0–160.0 μg mL⁻¹ (R = −0.9868) and C. humicola for 10.0–320.0 μg mL⁻¹ (R = −0.9955). The total heat dissipated per milliliter (Q_T) for three microbes remained balance approximately during the lower doses, P. putida and B. subtilis less than the dose of 20.0 μg mL⁻¹, 0.56 ± 0.01 and 0.26 ± 0.01 J mL⁻¹, respectively, C. humicola less than the dose of 40.0 μg mL⁻¹, 0.58 ± 0.03 J mL⁻¹. The biomass and OD₆₀₀ of three micro-organisms growth in the absence of AFS also were obtained. The power–time curve of C. humicola growth coincided with its turbidity curve. It elucidates that microcalorimetric method agreed with the routine microbiology method.     

Development and validation of a reversed-phase liquid chromatographic method for the assay of lidocaine in aqueous humour samples

A simple, fast and reliable reversed-phase liquid chromatographic method was developed for the assay of lidocaine in human aqueous humour samples. The samples were analysed without any preliminary treatment on a C8 column with UV detection at 225 nm. The mobile phase consisted of methanol/sodium dihydrogen phosphate (30 mM) containing sodium pentansulphonate (10 mM) adjusted to pH 2.5 with phosphoric acid (50:50 v/v). Validation of the method showed it to be precise, accurate and linear over the concentration range of analysis with a limit of detection of 0.2 μg ml⁻¹. The limit of quantitation was 2.5 μg ml⁻¹ with a relative standard deviation of 2.5%. Linear regression analysis in the range 2.5–60 μg ml⁻¹ gave correlation coefficients higher than 0.999. No interference from three commonly co-administered drugs was observed. The method developed was applied to the analysis of lidocaine in aqueous humour samples in order to evaluate and compare the efficacy of two different forms of administration of lidocaine for topical anaesthesia in cataract surgery.     

Ingestion of toxic Microcystis aeruginosa by dairy cattle and the implications for microcystin contamination of milk.

Microcystin (MCYST) toxins can be produced by the bloom-forming cyanobacterium Microcystis aeruginosa. They are chemically stable compounds and have both acute and chronic effects on the health of mammals, including cattle and humans. Cattle will drink water containing lethal cell concentrations of M. aeruginosa. When cattle consume sub-lethal doses of microcystins, the fate of those toxins is unknown. We provided drinking water containing 1×10⁵ cells ml⁻¹ M. aeruginosa (strain MASH01-A19) to four lactating Holstein–Friesian dairy cattle for 21 days to determine if MCYST-LR produced by the cyanobacteria, could be detected in milk produced by the cattle. Cattle consumed up to 15 mg MCYST-LR at an ingestion rate of 1.21 μg kg (live weight) d⁻¹. Analysis by HPLC and ELISA indicated that no detectable amounts of microcystin from the cyanobacteria were present in the milk obtained from the treated animals. Based on the level of quantitation of the ELISA analyses, the maximum possible concentration in the milk was less than 2 ng l⁻¹. This is more than three orders of magnitude less that the concentration that could be considered problematic for milk of 0.86 μg l⁻¹ which we calculated using the World Health Organization derived tolerable daily intake for MCYST-LR and the per capita daily consumption of milk in Australia.     

Selective kinetic determination of amikacin in serum using long-wavelength fluorimetry

A simple and rapid method for the determination of the antibiotic amikacin, involving the use of a long-wavelength fluorophor, namely indocyanine green, (ICG) is presented. The dye is oxidised by cerium(IV) in acidic medium, resulting in a sharp decrease of the fluorescence, but this fluorescence quenching is inhibited in the presence of amikacin, which can be ascribed to the formation of an ion pair between the fluorophor and the analyte. The initial rate of the system is monitored at λ_ex: 765 nm and λ_em: 812 nm as excitation and emission wavelengths, respectively, using the stopped-flow mixing technique, which makes the method applicable to automatic routine analysis. Each measurement is obtained in only 2–3 s. The method presents a detection limit of 0.02 μg m1⁻¹ in standard solutions, which corresponds to 2.5 μg ml⁻¹ in serum samples. The precision is in the range 4.8–6%. The good selectivity of the method allows amikacin to be determined in the presence of other antibiotics, including other aminoglycoside antibiotics, in serum. The recoveries obtained from the analysis of different samples were in the range 89.4–104.7%.     

Flow-injection biamperometric determination of epinephrine

A flow-injection manifold is proposed for the determination of epinephrine. The experimental procedure is based on the indirect biamperometric detection of the drug by using Fe(III)-Fe(II) as an indicating redox system and a flow-through detector with two polarized Pt wire electrodes. The calibration graph is linear over the range 0.3–20 μg ml⁻¹ of epinephrine. The relative standard deviation for the determination of 10 μg ml⁻¹ of epinephrine is 1.5% (n = 25) and the sample throughput is 153 h⁻¹. The method was applied to the determination of epinephrine in two commercially available pharmaceutical preparations.     

Pharmacokinetics of thrombin-like enzyme from venom of Agkistrodon halys ussuriensis Emelianov determined by ELISA in the rat.

A thrombin-like enzyme (TLE) was separated and purified from the venom of a northeast Chinese snake Agkistrodon halys ussuriensis Emelianov. Experiments were performed in rats to determine the pharmacokinetic parameters following an intravenous (i.v.) or a subcutaneous (s.c.) injection of the thrombin-like enzyme. The plasma levels of TLE were estimated by enzyme-linked immunosorbent assay. The method exhibited high reproducibility and accuracy in correlating optical densities with TLE concentrations (0.2–30 ng ml⁻¹, r=0.99). The plasma concentration-time course after i.v. administration of 50 μg kg⁻¹ TLE was well fitted by a two-compartment open model. The half-life of the -phase was 18.0±3.2 min, and that of the β-phase 3.9±0.7 h. The apparent volume of distribution was 1.8±0.5 l kg⁻¹, and clearance was 5.4±0.5 ml min⁻¹ kg⁻¹. When the TLE was injected s.c. at a dose of 0.75 mg kg⁻¹, the changes in plasma concentration were best described by a two-compartment model with a first-order absorption. The maximal plasma level of 51±2.7 ng ml⁻¹ was reached at 5.2±0.5 h. The absorption rate constant was 0.3±0.03 h⁻¹. The area under the plasma concentration-time curve (AUC) was 2.8±0.8 μg h⁻¹ ml⁻¹.     

Determination of bopindolol using the flow injection technique coupled with solid phase extraction

In the proposed procedure, the determination of bopindolol using a flow injection analysis (FIA) technique, with spectrophotometric detection at 635 nm, is described. The method is based on the production of a green, water-soluble complex with ferric ions in acid medium. The automated lab-made FIA system was used for the direct determination of bopindolol in tablets. Bopindolol was adsorbed onto the solid phase in a mini-column, which was integrated directly into the flow system. The positive feature of the use of solid phase extraction (SPE) was the pre-concentration of bopindolol (seven times). The sample throughput was 50 samples per hour. Using the SPE method, bopindolol was determined with a linear range from 125 to 1000 μg ml⁻¹ (Relative standard deviation (R.S.D.)=1.87%), with a detection limit (3σ) of 70 μg ml⁻¹. The method was applied to the determination of bopindolol in Sandonorm® tablets. The results obtained were compared with a conventional HPLC method, both analytical techniques were in good agreement.     

Spectrophotometric determination of oxytetracycline in pharmaceutical preparations using sodium molybdate as analytical reagent

A spectrophotometric method is proposed for the determination of oxytetracycline in pharmaceutical preparations. The method is based on the measurement of the absorbance of the molybdate—oxytetracycline complex at 404 nm (pH 5.50; μ = 0.1 M; 20°C). The composition of the complex (1:1) was determined by the application of the spectrophotometric methods of Job and Bent—French (pH 5.50; λ = 390 nm; μ = 0.1 M). The relative stability constant (K′ = 10^4.6) of the complex was obtained by the methods of Sommer and Nash (pH 5.50; λ = 390 nm; μ = 0.1 M; 20°C). The molar absorptivity of the complex was 9.5 × 10³ l mol⁻¹ cm⁻¹. Beer's law was obeyed over the concentration range 2.48–34.78 μg ml⁻¹. The relative standard deviation RSD (n = 10) was 0.27–0.39%. The method proposed can be applied to the assay of oxytetracycline in capsules. The detection limit of oxytetracycline is 2.5 μg ml⁻¹.     

Spectrophotometric determination of pefloxacin in pharmaceutical preparations

It has been established that the antibiotic pefloxacin (Abaktal) methane-sulphonate reacts with Fe(III) at pH 1.00–8.00 to form a water-soluble complex with maximum absorbance at 360 nm. The composition of the complex, determined spectrophotometrically by the application of Job's, molar-ratio and Bent—French's methods, was pefloxacin: Fe(III) = 1:1 (pH = 2.50; λ = 360 nm; μ = 0.1 M). The relative stability constant, obtained by the methods of Sommer and Asmus was 10^5.02 (pH = 2.50; λ = 360 nm; μ = 0.1 M). The molar absorptivity of the complex at 360 nm was found to be 4.8 × 10³ l mol⁻¹ cm⁻¹, Beer's law was followed for pefloxacin concentrations of 2.15–85.88 μg ml⁻¹. The lower sensitivity limit of the method was 2.15 μg ml⁻¹. The relative standard deviation (n = 10) was 0.57–1.07%. The method can be applied to the rapid and simple determination of pefloxacin in aqueous solutions and tablets.     

Lyophilized Cheliensisin A submicron emulsion for intravenous injection: characterization, in vitro and in vivo antitumor effect

Growing attentions have been focused on natural antitumor drugs. Recently, a novel and potent antitumor drug Cheliensisin A (GC-51) with broad-spectrum efficiency has been developed. However, due to its poor water solubility and chemical instability, choosing the appropriate dosage form is of great significance. This study aimed at developing a lyophilized submicron emulsion for GC-51 and further improving the therapeutic index of the drug. The resultant lyophilized GC-51 submicron emulsion was much more stable than its solution, which can be stored for years without significant change on physicochemical properties. And its solubility was increased from 6.74 ± 0.14 to 2.00 ± 0.10 mg mL⁻¹. The 50% inhibitory concentration IC₅₀ values were calculated from growth curves by MTT assay on various tumor cell lines. Compared with the IC₅₀ of GC-51 crude drug, that of lyophilized GC-51 submicron emulsion decreased from 24.04 ± 1.97 to 8.23 ± 1.84 μg mL⁻¹ on HepG2, and from 31.08 ± 2.56 to 10.85 ± 2.09 μg mL⁻¹ on CT-26, from 17.90 ± 1.83 to 7.49 ± 1.87 μg mL⁻¹ on HeLa and from 16.38 ± 2.41 to 10.13 ± 2.12 μg mL⁻¹ on A549, respectively. In the time-dependent assay of tumor cell viability, lyophilized GC-51 submicron emulsion exhibited significantly lower inhibition rate in the initial action times, but increased gradually afterwards. That means lyophilized submicron emulsion as the vector for GC-51 had some protective and delayed release effect. Further, the in vivo therapeutic efficacy was measured in pulmonary metastasis of colon cancer-bearing BALB/c mice model. An obvious enhanced antitumor activity was observed after administration of lyophilized GC-51 submicron emulsion (P < 0.05), which increased from 22.78 ± 3.5 to 41.42 ± 4.2% compared with GC-51 injection. And the life span of tumor-bearing mice in lyophilized GC-51 submicron emulsion group was significantly longer than that of the mice in GC-51 injection and normal saline groups. Compared with crude drug, the lyophilized GC-51 submicron emulsion showed a significantly higher antitumor efficiency both in vivo and in vitro, suggesting a potential application in tumor chemotherapy.     

Simultaneous analysis of methylprednisolone, methylprednisolone succinate, and endogenous corticosterone in rat plasma

A reversed-phase HPLC method is reported for simultaneous quantitation of methylprednisolone (MP), MP succinate (MPS), and endogenous corticosterone (CST) in plasma of rats. Additionally, the 11-keto metabolite of MP (methylprednisone, MPN) is resolved from the other analytes. After addition of internal standard (triamcinolone acetonide; IS) and an initial clean up step, the analytes of interest are extracted into methylene chloride. The steroids are then resolved on a reversed-phase polymer column using a mobile phase of 0.1 M acetate buffer (pH 5.7): acetonitrile (77:23) which is pumped at a flow rate of 1.5 ml min⁻¹. Sample detection was accomplished using an UV detector at a wavelength of 250 nm. All the five components (MPS, MP, MPN, CST and IS) were baseline resolved from each other and other components of plasma. Linear relationships were found between the steroids: IS peak area ratios and plasma concentrations in the range of 0.1–4 μg ml⁻¹ for MP and MPS and 0.1–1.0 μg ml⁻¹ for MPN and CST. The assay is accurate as intra- and inter-run error values were <±8% for all the components. Further, the intra- and inter-run CVs of the assay were <16% at all the concentrations and for all the components. The application of the assay was demonstrated after the injection of a single 5 mg kg⁻¹ (MP equivalent) dose of MPS or a macromolecular prodrug of MP to rats.     

A capillary GC-MS method for analysis of phenytoin and [C3]-phenytoin from plasma obtained from pulse dose pharmacokinetic studies

Stable isotope analogues of phenytoin are useful for pulse dose pharmacokinetic studies in epilepsy patients. A simultaneous assay was developed to quantitate phenytoin (5,5-diphenylhydantoin) and its stable isotope analogue [¹³C₃]-phenytoin (5,5-diphenyl-2,4,5-¹³C₃-hydantoin) from plasma. Quantitation was achieved by GC-MS analysis of liquid/liquid extracted plasma samples, with [²H₁₀]-phenytoin (5,5-di(pentadeuterophenyl)-hydantoin) as an internal standard. The total coefficients of variance (C.V._t) were <7% for phenytoin (2.5–40 μg ml⁻¹) and <10.3% for [¹³C₃]-phenytoin (0.1–6.0 μg ml⁻¹). The accuracy of the assay varied from 87.8–100.1% (phenytoin, 2.5–40 μg ml⁻¹) and 89.6–116.3% ([¹³C₃]-phenytoin, 0.02–6.0 μg ml⁻¹). The assay was tested under in vivo conditions by administration of a pulse dose of the stable isotope analogue to a single rat dosed to steady-state with fosphenytoin, a phenytoin prodrug. The results of the in vivo experiment demonstrate the usefulness of this assay for future pharmacokinetic studies in special population epilepsy patients.     

Spectrophotometric and atomic absorption spectrometric determination of certain cephalosporins

Two sensitive spectrophotometric and atomic absorption spectrometric procedures are developed for the determination of certain cephalosporins (cefotaxime sodium and cefuroxime sodium). The spectrophotometric methods are based on the charge-transfer complex formation between these drugs as n-donors and 7,7,8,8-tetracyano-quinodimethane (TCNQ) or p-chloranilic acid (p-CA) as π-acceptors to give highly coloured complex species. The coloured products are measured spectrophotometrically at 838 and 529 nm for TCNQ and p-CA, respectively. Beer’s law is obeyed in a concentration range of 7.6–15.2 and 7.1–20.0 μg ml⁻¹ with TCNQ, 95.0-427.5 and 89.0-400.5 μg ml⁻¹ with p-CA for cefotaxime sodium and cefuroxime sodium, respectively. The atomic absorption spectrometric methods are based on the reaction of the above cited drugs after their alkali-hydrolysis with silver nitrate or lead acetate in neutral aqueous medium. The formed precipitates are quantitatively determined directly or indirectly through the silver or lead content of the precipitate formed or the residual unreacted metal in the filtrate by atomic absorption spectroscopy. The optimum conditions for hydrolysis and precipitation have been carefully studied. Beer’s law is obeyed in a concentration range of 1.9–11.4 and 1.78–8.90 μg ml⁻¹ with Ag(I), 14.2–57.0 and 13.3–53.4 μg ml⁻¹ with Pb(II) for cefotaxime sodium and cefuroxime sodium, respectively (for both direct and indirect procedures). The spectrophotometric and the atomic absorption spectrometric procedures hold well their accuracy and precision when applied to the analysis of cefotaxime sodium and cefuroxime sodium dosage forms.     

LC/MS/MS analysis of vesnarinone and its principal metabolites in plasma and urine

An LC/MS/MS assay was developed and successfully used to quantitate vesnarinone and its principal metabolites (OPC-8230, OPC-18136, and OPC-18137) in human plasma and urine. Samples were pre-treated with liquid–solid extraction followed by simultaneous monitoring of primary and daughter ions which were used for the identification and quantitation of the analytes on LC/MS/MS. This assay offers advantages of specificity, speed and greater sensitivity over the previously developed HPLC-UV assay. The lower limit of quantitation is 500 ng ml⁻¹ for vesnarinone and 20 ng ml⁻¹ for OPC-8230, OPC-18137, and OPC-18136 in plasma. Methodology is similar for the estimation of these analytes in urine with the lower limit of quantitation being 500 ng ml⁻¹ for vesnarinone and 100 ng ml⁻¹ for each metabolite. Ascorbic acid was added to stabilize the analytes from degradation. This LC/MS/MS method was developed to overcome many practical problems associated with the HPLC method. The LC/MS/MS method offers the flexibility of analyzing additional metabolites and changing the linearity range to accommodate the differences in linear range (200–10 000 ng ml⁻¹ for vesnarinone and 20–1000 for metabolites) for the analytes.