Ceramic‐On‐Metal for Total Hip Replacement: Mixing and Matching Can Lead to High Wear

Ceramic‐on‐ceramic and metal‐on‐metal bearing surfaces are often employed for total hip replacement because of their resistance to wear. However, they have some limits: brittleness is a major concern for ceramic, and ion release is a drawback for metal. To reduce the effect of these limitations, a hybrid coupling of ceramic‐on‐metal has been proposed. The theoretical advantage of this new coupling might lead orthopedic surgeons to use it indiscriminately. We asked whether the wear rate of this innovative solution was comparable with that of ceramic‐on‐ceramic, which is considered to be the gold standard for wear resistance. In a hip simulator study, we tested the wear pattern of a hybrid ceramic‐on‐metal coupling supplied by the same distributor; in particular, three different configurations were tested for 5 million cycles: 36‐mm ceramic‐on‐ceramic, 32‐mm and 36‐mm ceramic‐on‐metal. These combinations were gravimetrically and geometrically evaluated. After 5 million cycles, the volumetric loss for the metal acetabular cups (Φ 36‐mm) was 20‐fold greater than that of the ceramic cups of the same size (Φ 36‐mm); a volumetric loss of 4.35 mm³ and 0.26 mm³ was observed, respectively, for ceramic‐on‐metal and ceramic‐on‐ceramic combinations. Significant statistical differences were observed between all 36‐mm different combinations (P < 0.0001). The increased diameter of the 36‐mm ceramic‐on‐metal configuration resulted in a lower volumetric loss compared with that of the 32‐mm ceramic‐on‐metal configuration. Our findings showed an increase in wear for the proposed hybrid specimens with respect to that of the ceramic‐on‐ceramic ones. This confirms that even in the case of ceramic‐on‐metal bearings, mixing and matching could not prove effective wear behavior, not even comparable with that of the ceramic‐on‐ceramic gold standard.     

A meta‐analysis of design‐ and manufacturing‐related parameters influencing the wear behavior of metal‐on‐metal hip joint replacements

This article aims to clarify the influence of design‐ and manufacturing‐related parameters on wear of metal‐on‐metal (MoM) joint bearings. A database search for publications on wear simulator studies of MoM bearings was performed. The results of published studies were normalized; groups with individual parameters were defined and analyzed statistically. Fifty‐six investigations studying a total of 200 implants were included in the analysis. Clearance, head size, carbon content, and manufacturing method were analyzed as parameters influencing MoM wear. This meta‐analysis revealed a strong influence of clearance on running‐in wear for implants of 36‐mm diameter and an increase in steady‐state wear of heat treated components. © 2009 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 27:1473–1480, 2009     

Metal ion concentrations and semen quality in patients undergoing hip arthroplasty: A prospective comparison between metal‐on‐metal and metal‐on‐polyethylene implants

Purpose: The widespread usage of metal‐on‐metal (MoM) articulations in total hip arthroplasty (THA) has been tempered by concerns of increased metal ion production. The purpose of the study is to evaluate the influence of metal ion exposure on semen quality in young male patients undergoing THA. Methods: Male patients who were scheduled for unilateral THA and aged between 20 and 45 years were prospectively enrolled. Patients were sorted into MoM and metal‐on‐polyethylene (MoP) groups with equal case number. Semen and blood metal ion levels were measured and sperm analysis was performed before, 6 months after, and 1 year after surgery. Results: Compared to preoperative baseline, patients (n = 50) in both groups had increased cobalt (Co) and chromium (Cr) concentrations in blood and seminal fluid after surgery. Between‐group comparisons at 6 months and 1 year after surgery showed that patients in the MoM group both had a greater Co concentration in blood and semen and a greater Cr concentration in blood and semen. Patients receiving MoM prosthesis had a reduced percentage of morphologically normal sperm, and decreases from the preoperative level (44.7%) were significant at 6 months (36.8%, p = 0.03) and 1 year (33.8%, p = 0.004). Conclusions: Our data shows a significantly greater concentration of metal ion in blood and semen in patients with MoM prosthesis with a reduced percentage of morphologically normal sperm. Despite small effects on sperm quality, some concerns remain. Further studies are necessary to determine sources of metal ion and to investigate effects on male fertility. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 34:544–551, 2016.     

Asymptomatic prospective and retrospective cohorts with metal‐on‐metal hip arthroplasty indicate acquired lymphocyte reactivity varies with metal ion levels on a group basis

Some tissues from metal‐on‐metal (MoM) hip arthroplasty revisions have shown evidence of adaptive‐immune reactivity (i.e., excessive peri‐implant lymphocyte infiltration/activation). We hypothesized that, prior to symptoms, some people with MoM hip arthroplasty will develop quantifiable metal‐induced lymphocyte reactivity responses related to peripheral metal ion levels. We tested three cohorts (Group 1: n = 21 prospective longitudinal MoM hip arthroplasty; Group 2: n = 17 retrospective MoM hip arthroplasty; and Group 3: n = 20 controls without implants). We compared implant position, metal‐ion release, and immuno‐reactivity. MoM cohorts had elevated (p < 0.01) amounts of serum Co and Cr compared to controls as early as 3 months post‐op (Group 1:1.2 ppb Co, 1.5 ppb Cr; Group 2: 3.4 ppb Co, 5.4 ppb Cr; Group 3: 0.01 ppb Co, 0.1 ppb Cr). However, only after 1–4 years post‐op did 56% of Group 1 develop metal‐reactivity (vs. 5% pre‐op, metal‐LTT, SI > 2), compared with 76% of Group 2, and 15% of Group 3 controls (patch testing was a poor diagnostic indicator with only 1/21 Group 1 positive). Higher cup‐abduction angles (50° vs. 40°) in Group 1 were associated with higher serum Cr (p < 0.07). However, sub‐optimal cup‐anteversion angles (9° vs. 20°) had higher serum Co (p < 0.08). Serum Cr and Co were significantly elevated in reactive versus non‐reactive Group‐1 participants (p < 0.04). CD4+CD69+ T‐helper lymphocytes (but not CD8+) and IL‐1β, IL‐12, and IL‐6 cytokines were all significantly elevated in metal‐reactive versus non‐reactive Group 1 participants. Our results showed that lymphocyte reactivity to metals can develop within the first 1–4 years after MoM arthroplasty in asymptomatic patients and lags increases in metal ion levels. This increased metal reactivity was more prevalent in those individuals with extreme cup angles and higher amounts of circulating metal. © 2012 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 31: 173–182, 2013     

Lymphocyte proliferation responses in patients with pseudotumors following metal‐on‐metal hip resurfacing arthroplasty

Locally destructive soft tissue pseudotumor has been reported in patients following metal‐on‐metal hip resurfacing arthroplasty (MoMHRA). A delayed hypersensitivity reaction type IV to nickel (Ni), chromium (Cr), or cobalt (Co) has been suggested to play a role in its aetiology. The aim of this study was to investigate the incidence and level of metal‐induced systemic hypersensitivity in patients with MoMHRA, both with and without pseudotumor by measuring lymphocyte proliferation responses to metals. A total of 92 patients were investigated: (1) MoMHRA patients with pseudotumors (nine female, one male); (2) MoMHRA patients without pseudotumors (30 female, 30 male); and (3) age‐matched control subjects without metal implants (9 female, 13 male). The venous blood samples were collected for serum Ni, Co, and Cr ion level measurements and lymphocyte transformation tests (LTT). A higher incidence and level of enhanced lymphocyte reactivity only to Ni was found in patients with MoMHRA compared to the patients without MoM implants, reflecting exposure and immune reactivity. However, lymphocyte reactivity to Co, Cr, and Ni did not significantly differ in patients with pseudotumors compared to those patients without pseudotumors. This suggests that systemic hypersensitivity type IV reactions, as measured by lymphocyte proliferation response to these metals, may not be the dominant biological reaction involved in the occurrence of the soft tissue pseudotumors. © 2009 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 28:444–450, 2010     

Strong association between smoking and the risk of revision in a cohort study of patients with metal‐on‐metal total hip arthroplasty

Thus far the ability to predict who will develop early failure following the insertion of a metal‐on‐metal (MoM) bearing has been very limited. Our objective was to assess the effect of smoking on failure rates in patients with MoM bearing, compared with patients with ceramic‐on‐polyethylene (CoP) bearing. From a prospective hospital‐based registry we included all primary THAs operated upon between 1/2001 and 12/2011 with MoM or CoP bearings of the same cup design and head size (28 mm). We compared revision rates through 10/2013 classified by smoking status and type of bearing. We included 1,964 patients (median age 71, 57% women), 663 with MoM and 1,301 with CoP bearing. Mean follow‐up was 6.9 years (range 1.8–12.8). Revisions were required for 56 THAs. In patients with MoM bearing the adjusted incidence rate of revision among ever‐smokers was four times greater than among never‐smokers (95% CI 1.4–10.9). Among those with CoP bearing, the rate ratio was only 1.3 (95% CI 0.6–2.5). We found a strong association between smoking and increased failure of MoM THAs. In contrast, the association was weak for patients with CoP bearing. Smoking might be a trigger or an effect amplifier for adverse reactions to metal debris from MoM bearings. © 2014 The Authors. Journal of Orthopaedic Research Published by Wiley Periodicals, Inc. J Orthop Res 32:762–768, 2014.     

Predicting wear and blood metal ion levels in metal‐on‐metal hip resurfacing

Suboptimal component position and design are thought to lead to edge wear and raised blood metal ion levels in metal‐on‐metal hip resurfacing (MOM‐HR). These factors are thought to influence the “contact patch to rim distance” (CPRD), and calculation of this distance may improve prediction of wear and blood metal ion levels. We measured blood cobalt and chromium ion levels and the wear rates of the bearing surfaces in 165 MOM‐HR retrieval cases. We then determined the contribution and effect sizes of cup inclination and version angles, component size and design, and CPRD (calculated from case‐specific data) on blood metal ion levels and component wear rates. Acetabular orientation explained between 16.3% and 28.5% of the variation in wear rates and metal ion levels, whereas component size and design explained between 7.3% and 21.8% of the variability. In comparison, CPRD explained up to 67.7% of the variability, significantly greater than any other variable (all p < 0.0001). CPRD is a good predictor of wear and improves our understanding of wear performance and the mechanisms leading to edge loading. © 2013 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 32:167–174, 2014.     

Wear mechanisms in metal‐on‐metal bearings: The importance of tribochemical reaction layers

Metal‐on‐metal (MoM) bearings are at the forefront in hip resurfacing arthroplasty. Because of their good wear characteristics and design flexibility, MoM bearings are gaining wider acceptance with market share reaching nearly 10% worldwide. However, concerns remain regarding potential detrimental effects of metal particulates and ion release. Growing evidence is emerging that the local cell response is related to the amount of debris generated by these bearing couples. Thus, an urgent clinical need exists to delineate the mechanisms of debris generation to further reduce wear and its adverse effects. In this study, we investigated the microstructural and chemical composition of the tribochemical reaction layers forming at the contacting surfaces of metallic bearings during sliding motion. Using X‐ray photoelectron spectroscopy and transmission electron microscopy with coupled energy dispersive X‐ray and electron energy loss spectroscopy, we found that the tribolayers are nanocrystalline in structure, and that they incorporate organic material stemming from the synovial fluid. This process, which has been termed “mechanical mixing,” changes the bearing surface of the uppermost 50 to 200 nm from pure metallic to an organic composite material. It hinders direct metal contact (thus preventing adhesion) and limits wear. This novel finding of a mechanically mixed zone of nanocrystalline metal and organic constituents provides the basis for understanding particle release and may help in identifying new strategies to reduce MoM wear. © 2009 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 28:436–443, 2010     

Comparison of synovial fluid,urine, and serum ion levels in metal‐on‐metal total hip arthroplasty at a minimum follow‐up of 18 years

Diagnosis of adverse reactions to metal debris in metal‐on‐metal hip arthroplasty is a multifactorial process. Systemic ion levels are just one factor in the evaluation and should not be relied upon solely to determine the need for revision surgery. Furthermore, the correlation between cobalt or chromium serum, urine, or synovial fluid levels and adverse local tissue reactions is still incompletely understood. The hypothesis was that elevated serum and urine metal‐ion concentrations are associated with elevated local metal‐ion concentrations in primary total hip arthroplasties (THA) and with failure of metal‐on‐metal articulations in the long‐term. In our present study, we evaluated these concentrations in 105 cementless THA with metal‐on‐metal articulating surfaces with small head diameter at a minimum of 18 years postoperatively. Spearman correlation showed a high correlation between the joint fluid aspirate concentration of cobalt and chromium with the serum cobalt (r = 0.81) and chromium level (r = 0.77) in patients with the THA as the only source of metal‐ions. In these patients serum metal‐ion analysis is a valuable method for screening. In patients with more than one source of metal or renal insufficiency additional investigations, like joint aspirations are an important tool for evaluation of wear and adverse tissue reactions in metal‐on‐metal THA. © 2014 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 32:1234–1240, 2014.     

In vitro investigation of friction under edge‐loading conditions for ceramic‐on‐ceramic total hip prosthesis

Edge‐loading generates higher wear rates in ceramic‐on‐ceramic total hip prosthesis (THP). To investigate the friction coefficient (FC) in these conditions, three alumina ceramic (Biolox Forte) 32 mm‐diameter components were tested using a hip friction simulator. The cup was positioned with a 75° abduction angle to achieve edge‐loading conditions. The motion was first applied along the edge and then across the edge of the cup. First, tests were conducted under lubricated conditions with 25% bovine serum. Next, to simulate an extremely high contact pressure, the tests were run with the addition of a third body alumina ceramic chip inserted between the edge of the cup and the head. Engineering blue was used to analyze the contact area. Reference values were determined using a 0° cup abduction angle. Edge loading was achieved. The FC increased by three‐ to sixfold when the motion was applied along the edge, and by 70% when the motion was applied across the edge. However, the FC value was still low (about 0.1), which is similar to metal‐on‐metal THP. With the third body alumina ceramic particle inserted, the FC was 26 times higher than in the ideal conditions and intermittent squeaking occurred. High cup abduction angles may generate edge‐loading and an increase in the friction coefficient for ceramic THP. © 2010 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 28:979–985, 2010     

Concomitant evolution of wear and squeaking in dual‐severity,lubricated wear testing of ceramic‐on‐ceramic hip prostheses

Ceramic‐on‐ceramic (CoC) hip bearings were tested in short‐term wear tests with a systematically varied contact force. Continuous vibration and intermittent surface roughness measurements were obtained to elucidate potential causes of in vivo hip joint squeaking. The three‐phase test comprised alternating cycles of edge loading (EL) and concentric articulation (CA), always using ample serum lubricant. A 50,000‐cycle wear trial in which the contact force during CA was distant from the head's wear patch yielded no squeaking and practically no liner roughening. In 10‐cycle trials of an edge‐worn head coupled with a pristine liner, the contact force was varied in magnitude and point of application; immediate, recurrent squeaking occurred only when the contact force exceeded a critical threshold value and was centered upon the head's wear patch. In a 27,000‐cycle wear trial with the contact force applied near the margin of the head's wear patch, recurrent squeaking emerged progressively as the liner's inner surface was roughened via its articulation with the worn portion of the head. The results reveal key conditions that yield recurrent squeaking in vitro in various scenarios without resorting to implausible dry conditions. A fundamental theory explains that hip squeaking is induced by myriad stress waves emanating from asperity collisions; yet, the root cause is edge loading. © 2012 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 30:1377–1383, 2012     

Squeaking in ceramic‐on‐ceramic hips: No evidence of contribution from the trunnion morse taper

Squeaking in ceramic‐on‐ceramic (CoC) total hip arthroplasty (THA) was investigated with an acoustic monitoring device to distinguish between squeaking emanating from the trunnion morse taper (TMT) connection versus the articular surface. 82 patients with implant problems scheduled for revision were selected and acoustic emissions (AE) with simple movements monitored. Five of these patients with CoC implants underwent surgery and their retrieved implant components were analyzed in vitro. In vivo recordings of all 82 patients found audible squeaks produce frequency content across the entire 0–50 kHz spectrum. Of the five CoC implants the in vivo peak frequency range of flexion/extension motions was 0.8 kHz and comparable to the range of in vitro testing (0.2 kHz). In vitro TMT connection motions were very large comparatively, producing a higher average peak frequency range of 22.5 kHz. All retrieved implants showed evidence of wear at the TMT connection. These findings suggest, the TMT connection does not directly cause audible squeaking. Wear occurring at this junction may contribute to debris which disrupt lubrication, increase friction, and produce noise. This observation supports current evidence suggesting that squeaking is from the bearing surface. Our findings are the first to demonstrate that in CoC THA the recordable noise of a hip squeak does not originate nor have contribution from the TMT connection. © 2016 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:1793–1798, 2017.

     

Effects of chronic cobalt and chromium exposure after metal‐on‐metal hip resurfacing: An epigenome‐wide association pilot study

Metal‐on‐metal (MOM) hip resurfacing has recently been a popular prosthesis choice for the treatment of symptomatic arthritis, but results in the release of cobalt and chromium ions into the circulation that can be associated with adverse clinical effects. The mechanism underlying these effects remains unclear. While chromosomal aneuploidy and translocations are associated with this exposure, the presence of subtle structural epigenetic modifications in patients with MOM joint replacements remains unexplored. Consequently, we analyzed whole blood DNA methylation in 34 OA patients with MOM hip resurfacing (MOM HR) compared to 34 OA patients with non‐MOM total hip replacements (non‐MOM THR), using the genome‐wide Illumina HumanMethylation 450k BeadChip. No probes showed differential methylation significant at 5% false‐discovery rate (FDR). We also tested association of probe methylation levels with blood chromium and cobalt levels directly; there were no significant associations at 5% FDR. Finally, we used the “epigenetic clock” to compare estimated to actual age at sample for all individuals. We found no significant difference between MOM HR and non‐MOM THR, and no correlation of age acceleration with blood metal levels. Our results suggest the absence of large methylation differences systemically following metal exposure, however, larger sample sizes will be required to identify potential small effects. Any DNA methylation changes that may occur in the local periprosthetic tissues remain to be elucidated. © 2017 The Authors. Orthopaedic Research Society. Published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society. J Orthop Res 35:2323–2328, 2017.

     

Whole Blood Metal Ion Concentrations in Correlation With Activity Level in Three Different Metal-On-Metal Bearings

Seventy consecutive osteoarthritis patients younger than 65 years undergoing a hip arthroplasty were included. Three different metal bearings were used (2 different resurfacing systems and one 28-mm metal bearing) and compared with a ceramic control group. Whole blood cobalt and chromium levels were analyzed preoperatively, at 3 months, 6 months, 1 year, and 2 years. Patients with steep cups (abduction >55°) were excluded. No significant differences in functional scores and activity level were found between either groups. Ion levels were significantly lower with one type of resurfacing. No correlation was found between ion and activity level. In conclusion, although the current second-generation metal bearings may show differences in ion release, more attention should be paid to the correlation between ion release and implant positioning.     

Current in vivo wear of metal-on-metal bearings assessed by exercise-related rise in plasma cobalt level.

Baseline metal ion levels are elevated in patients with metal-on-metal (MOM) hip arthroplasty. Interpretation of baseline levels is difficult as measurements are influenced by wear, corrosion, and metal ion release from stored metal in the body. Schmalzried et al. demonstrated that "wear is the function of use, not time." The specific research question we asked was: Does physiological exercise increase the wear of metal-on-metal articulation which can be measured from the plasma metal ion levels? Patients with three different well functioning MOM bearings [two types of resurfacing (BHR 46.8 mm and Cormet 48 mm) and Metasul 28 mm] were included. Blood samples were taken immediately before, immediately after, and 1 h after exercise to determine cobalt and chromium levels. A significant increase (p<0.005) in serum cobalt and chromium of 13% and 11%, respectively, was noticed after the exercise. Rise of cobalt levels in patients with a resurfacing MOM was 8.5 times (BHR group) or 6.5 times (Cormet group) larger than in those with a Metasul MOM (p=0.021 and p=0.047). Neither rise of metal levels nor baseline levels correlated with any other factor (p>0.27). Exercise-related elevations of plasma cobalt level provides information on current in vivo wear production that cannot be inferred from a baseline measurement of cobalt levels. Chromium levels cannot provide reliable information on the in vivo wear of the devices. Diameter was the important feature of the implant in determining exercise-related elevations of plasma cobalt level. Exercise-related elevations of plasma cobalt level is a potential in vivo tool to understand and improve the tribology of metal-metal bearings.     

Material loss at the taper junction of retrieved large head metal‐on‐metal total hip replacements

It has been speculated that material loss, either as corrosion or wear, at the head–stem taper junction is implicated in the high revision rates reported for metal‐on‐metal total hip replacements. We measured the volume of material loss from the taper and bearing surfaces of retrieved devices, and investigated the associations with blood metal ion levels and the diagnosis of a cystic or solid pseudotumor. The median volumes of material lost from the female and male taper surfaces were 2.0 and 0.29 mm³, respectively, while the median volumes of wear from the cup and head bearing surfaces were 1.94 and 3.44 mm³, respectively. Material loss from the female taper was similar to that from the acetabular bearing surface (p = 0.55), but significantly less than that from the femoral bearing surface (p < 0.001). Material loss from the male taper was less than that from both bearing surfaces (p < 0.001). Multivariable analysis demonstrated no significant correlations between the volume of material lost from the taper surfaces and either blood cobalt or chromium ions, or the presence of pseudotumor. While a substantial volume of material is lost at the taper junction, the clinical significance of this debris remains unclear. © 2013 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 31:1677–1685, 2013     

No Differences Found in Bearing Related Hip Survivorship at 10–12 Years Follow-Up Between Patients With Ceramic on Highly Cross-Linked Polyethylene Bearings Compared to Patients With Ceramic on Ceramic Bearings

At a minimum follow-up of ten years we compared clinical and radiographic findings and survivorship in a cohort of 412 patients (447 hips) who received alumina on alumina CoC bearings to findings from a cohort of 216 patients (228 hips) with alumina on highly cross-linked polyethylene (HXLPE) bearings. All patients were operated for osteoarthritis. With bearing-related complications as endpoint, analysis showed no significant difference in survivorship between cohorts (99.8% for the CoC vs. 99.4% for HXLPE). In addition, there were no significant differences in clinical and radiographic findings between cohorts. We concluded that alumina on HXLPE bearings are a reasonable lower cost alternative to ceramic on ceramic bearing couples.     

Edge‐loading severity as a function of cup lip radius in metal‐on‐metal total hips—A finite element analysis

While favorable tribological properties and allowance for larger femoral head sizes have made metal‐on‐metal (MoM) bearings an increasingly popular choice for total hip arthroplasty, concerns have mounted regarding adverse reactions to metal wear debris and ions. MoM cups differ from conventional polyethylene cups in terms of edge profile design and reductions from full hemisphericity, suggesting differences in loading at or near the cup edge, especially during subluxation events. Finite element analysis was used to investigate the effects of cup orientation and lip edge curvature on damage propensity for edge or near‐edge loading during subluxation. Increased cup lip radius (resulting in reduced articular arc) had a detrimental effect upon subluxation‐free hip range of motion and upon dislocation resistance. Contact stresses near the cup edge demonstrated complex relationships between edge radius and cup orientation, with peak stresses being influenced by both variables. The tendency for scraping wear at the egress site demonstrated similarly complex dependencies. These data indicate that acetabular cup design is an important determinant of edge and near‐edge loading damage propensity. © 2011 Orthopaedic Research Society Published by Wiley Periodicals, Inc. J Orthop Res 30:169–177, 2012     

Co and Cr accumulation in hair after metal-on-metal hip resurfacing arthroplasty

Background: Currently, it is unclear whether Co and Cr levels are persistently elevated in the body after hip resurfacing arthroplasty (HRA). This study aimed to evaluate Co and Cr levels in the body after HRA using hair as samples. Methods: Among 22 patients who had metal‐on‐metal HRA (m‐o‐m group) using the DePuy ASR system, scalp hair of 1.5 cm in length and 2 g in weight was collected before and at 6 and 12 months after surgery. Inductively coupled plasma‐mass spectrometry (ICP‐MS) was used to detect Co and Cr levels in the scalp hair. Another 22 patients with total hip replacements were randomly selected from a similar age range as controls (m‐o‐p group). Metal levels in hair were detected with multiple measurements and analysed by repeated measures analysis of variance. Results: Both Co and Cr levels were significantly increased in the m‐o‐m group after surgery compared with those in the m‐o‐p group (P < 0.01). Co levels at 6 months post‐operatively were 12‐fold those before surgery, and Co levels 12 months post‐operatively were lower than those at 6 months, but this difference was not significant (P= 0.0805) between the two time points in the m‐o‐m group. Cr levels were persistently elevated after surgery and were increased by 10‐fold compared with those at baseline in the m‐o‐m group. Conclusions: Co and Cr levels in scalp hair are ideal indicators for metal levels in the body after HRA. Co and Cr levels in the body were greatly increased after metal‐on‐metal HRA. Long‐term accumulation of these metals needs to be further investigated.     

Differences in ion release after ceramic-on-ceramic and metal-on-metal total hip replacement. Medium-term follow-up

Modern metal-on-metal bearings produce less wear debris and osteolysis, but have the potential adverse effect of release of ions. Improved ceramic-on-ceramic bearings have the lowest wear of all, but the corrosion process has not been analysed. Our aim was to measure the serum ion release (ng/ml) in 23 patients having stable hip prostheses with a ceramic-on-ceramic coupling (group A) and to compare it with the release in 42 patients with a metal-on-metal bearing (group B) in the medium term. Reference values were obtained from a population of 47 healthy subjects (group C). The concentrations of chromium, cobalt, aluminium and titanium were measured. There was a significant increase of cobalt, chromium and aluminium levels (p < 0.05) in group B compared with groups A and C. Group A did not differ significantly from the control group. Despite the apparent advantage of a metal-on-metal coupling, especially in younger patients with a long life expectancy, a major concern arises regarding the extent and duration of ion exposure. For this reason, the low corrosion level in a ceramic-on-ceramic coupling could be advantageous.