Retracted Article: Facile preparation of bithiazole-based material for inkjet printed light-emitting electrochemical cell

Light-emitting electrochemical cell of bithiazole-based material was fabricated by solution processing rendered high external quantum efficiency over 12.8% and luminance of 1.8 10⁴ cd m⁻².

Light-emitting electrochemical cell of bithiazole-based material was fabricated by solution processing rendered high external quantum efficiency over 12.8% and luminance of 1.8 10⁴ cd m^−2.

It is well known that inkjet printing works as precise and versatile patterning method for printed electronics.^1,2 As for its advantages, it is already being exploited widespread for printing electronics.^3,4 Those merits are easily processed from solutions and conveniently used for air-stable electrodes.^5,6Light-emitting electrochemical cells (LECs) have emerged as an active layer,^7,8 arousing tremendous attention over the years.^9–11 Nevertheless, LECs are simpler than organic light-emitting diodes (OLEDs).^12,13 Due to its single layer architecture, low fabrication price and operating voltages, LECs are considered as a promising, next-generation, emissive thin-film technology.^14–16The most efficient device used to date for LECs are biscyclometalated iridium(iii) (Ir) complexes, because they have highly efficient and stable devices spanning the whole visible range.^17–19 However, avoiding the use of Ir is strongly desired because of its high cost and limited supply.^20–22 Till now, thiazole has worked as active component in a LECs system with a long-lived charge-separation molecule, without additional ions in its active layer.^23–26 As for its advantages, it can reduce recombination of charge carriers and facilitate carrier transfer.^27–29 More and more importance has been attached to thiazole compounds, especially bithiazole-based ones.^30–33 Therefore, these have aroused interest in the syntheses of bithiazoles.^34–36Based on our previous research,^37–41 the use of bithiazole ligands already explored by our group for photocatalytic technology has the advantage of an easy transformation of neutral complexes into charged ones by substitution on the N-atom of the thiazole moiety.^42,43 Furthermore, we demonstrate the fabrication of LEC devices by a combination of inkjet printing and spin coating, on A4 paper substrates for low cost, disposable and flexible conductive pattern.^44,45 Their corresponding material characteristics were closely investigated, a detailed report of the material properties of the resulting coatings, and an envisaged proof of concept application are disclosed in this paper. These fully printed devices demonstrate the potential upscaling of the fabrication of optoelectronic devices.Herein we report the design for a range of bithiazole derivatives 1a–1c (Fig. 1, their synthesis is shown in Scheme S1^†), and explore their properties. First of all, the UV-visible diffuse-reflectance (UV-vis DRS) spectra of those specimens at room temperature are displayed in Fig. 2 and the data are collected in Table S1.^† This enhancement was ascribed to the increase of aromatic rings, which has an intense absorption in the visible-light region. And their bandgap energies (E_g) are between 2.97–3.01 eV (Table S1^†), and are estimated from these absorption spectra according to the Kubelka–Munk method. Expanding the conjugated system and electron density with these donor groups, it can lead to a larger bathochromic shift of the absorption maximum.^46,47Open in a separate windowFig. 1Chemical structures of compounds 1a–1c described in this work.Open in a separate windowFig. 2UV-vis DRS spectra of 1a–1c.All of the three compounds are photoluminescent at room temperature, the relevant fluorescence peak maximum ranges from 360 to 398 nm (Fig. 3). They emit blue light when they are being excited. In agreement with Fig. 3, the presence of electron-releasing groups would shift the emission maximum. Among them, the most electron-donating carbazole unit would give the most red-shifted peak at 398 nm for 1c (Table S1^†). The PL quantum yield (ϕ_PL) studies show that both 1a and 1b are as high as 62 and 78%, while another one is 85% (Table S1^†). The data for their fluorescent quantum yields largely depends on interaction effect with molecules 1a–1c in the crystal packing. In this context, π–π intermolecular interactions can inhibit the fluorescence.⁴⁸Open in a separate windowFig. 3Typical PL spectra of 1a–1c.It may indicate that enlarging the conjugation length and electron density with these donor groups plays an important role in increasing the ϕ_PL.⁴⁹ Moreover, those with high ϕ_PL may be suitable for application as efficient light-emitting material in LECs.⁵⁰In addition, time-resolved measurements of the donor lifetime (τ) in 1a–1c were carried out, and their corresponding values are given in Table S1.^† The bithiazole derivatives 1a–1c showed long-lived singlet fluorescence lifetimes (τ_F), ranging between 1.04 and 9.54 ns (Table S1^†). This was on average more than double the fluorescence lifetime of the bithiazole starting material.⁵¹ These three samples possess relatively high decay time, as a result of their inhomogeneity.⁵² Compound 1c exhibited the longest fluorescence lifetime decay τ_F = 9.54 ns. The sensitivity of the emission to the polarity of the solvent is beneficial for an intramolecular charge transfer (ICT)-like emission.⁵³ This difference probably accounts for the high concentration of donor units in the bithiazole backbone, low rates of intersystem crossing to reactive triplet states.^48,54Consequently, the composite 1c was the best performing LEC and chosen for the below test. The EL spectra obtained for both devices were almost identical, with a main peak at 498 nm and other peak at 504 nm wavelength as illustrated in Fig. 4a. It may account for trapping, cavity, and self-absorption effects from within the LEC device 1c multilayer-structure. The spin-coated emission is quantified by the commission Internationale de L’Eclairage (CIE) coordinates of (0.28, 0.42), and a colour rendering index (CRI) of 65 (Table S2^†). While inkjet-printed light emission with CIE coordinates of (0.34, 0.43) and a CRI value of 83 was achieved for device 1c (Table S2^†). It exhibits good colour rendering indices (CRI > 70), this device exhibited a warm-white appearance, and the colour rendering is considered sufficient for indoor lighting applications.Open in a separate windowFig. 4Comparison of device characteristics with spin-cast and inkjet printer emitting layer for 1c: (a) electroluminescent spectra, (b) luminance vs. voltage, (c) current density vs. voltage, (d) efficiency vs. luminance behaviour.The time-dependent brightness and current density under constant biases of 2.9–3.3 V for device 1c are shown in Fig. 4b and c. Interestingly, the device with the inkjet-printed emitting layer (EML) produced a light output of around 3600 cd m⁻², whereas 4600 cd m⁻² was achieved with the spin-coated EML. In other words, the device with the inkjet printed EML obtained about 78.3% of brightness compared with the reference device. The differences between the two devices regarding current efficiency (J) and power efficiency (PE) were rather closed, as listed in the Table S2.^† A luminous efficiency much larger than 10 cd A⁻¹ was achieved for the inkjet-printed EML, which tended to be 73.9%, and is similar to the spin-coated emitting layer.The performance gap between the devices (Fig. 4d) can be attributed to differences in the height and surface roughness of the emitting layer.⁵⁵ Lateral sizing histograms (Fig. S11^†) show that the spin-coated EML possessed a thickness of 35 nm and a very smooth surface. The inferior performance of the inkjet-printed EML is caused by a less homogeneous surface morphology and an overall fatter layer.⁵⁶ The depth of the inkjet-printed EML ranged from 25 nm (pixel centre) to 35 nm (pixel edges). As a consequence, it is an inkjet deposition process and the related evaporation dynamics reduces the light output and efficiency, but also postpones the stability of the device in the system.^10,57We then shifted our attention to the turn-on kinetics, efficiency and long-term stability of the LEC device for 1c; the typical evolution of current density and light emission is presented in Fig. 5a and b, showing a slow turn-on followed by a progressive decay over time.Open in a separate windowFig. 5(a) Current density (closed symbols) and brightness (open symbols) versus time at 3 V for a device with the representative sample 1c; (b) EQE versus time at an applied voltage of 3 V.The build-up of the light output is synchronous with that of the current density. This time-delayed response is one of the striking features of the operation of an electrochemical cell and reflects the mechanism of device operation.²² The champion device in this set exhibited a peak power efficiency (PE) of 17.4 lm W⁻¹ at a luminance of 18 000 cd m⁻². Meanwhile, the current density began to decrease, possibly due to the electrochemical oxidation or electro corrosion that occurred on component 1c through accumulated electroinduced holes, and then it kept up a durative datum.⁵⁸ Apparently it exhibited outstanding long-term operation stability beyond 40 h (Fig. 5b).The time-dependent external quantum efficiency (EQE) of LEC for the representative substrate 1c are shown in Fig. 5b. It also exhibited similar temporal tendency in device efficiency. When a bias was applied on the LECs, the EQE quickly increased since balanced carrier injection was achieved by the formation of the doped layers.⁵⁹ After attaining the crest value, the device current was still rising while the EQE reduced little by little. It implied that both growing the doped layers and weakening of the EQE was resulting from exciton quenching near the bithiazlole core in persistently extended doped layers.⁶⁰ Doping-induced self-absorption was rather adaptable to the temporal roll-off in device efficiency. This configuration shows the best performance (EQE = 12.8%) compared to those devices prepared with the single compounds, which is given in Table S3.^† The reason may be that the steady-state recombination zone in 1c device was close to the central active layer.⁶¹ Besides it contains fluorenes on its side chains, constructing plane structure, benefiting from good electron injection abilities, leading to enhancing the EQE itself.⁶²The fabrication of inkjet-printed bithiazole interdigitated electrode (IDE) is illustrated in Fig. 6. All the prepared varieties of bithiazole-based ink have been found to be highly stable with nil or miniscule precipitation in over 180 days being stored on the shelf (Fig. 6a). After HCl treatment of the paper substrate, the prepared inks have filled within ink cartridges of a low-cost desktop printer Canon iP1188 (Fig. 6b). Fig. 6c shows the photograph of inkjet-printed conductive patterns.Open in a separate windowFig. 6(a) The representative ink based on sample 1c was stable for 180 days; (b) electrode printing using Canon iP1188 printer; (c) scale showing size of printed electrodes; (d) interdigitated electrode (inset shows small size printed pattern).In addition, the most attractive prospect of the bilayer device structure at this stage is the possibility for patterned emission for the creation of a static display. Fig. 7 presents a photograph of a small portion of a larger static display, with a resolution of 170 PPI, which repeatedly exhibits a message in the form of the word “LEC”. As shown in Fig. 7, the pixel array produced are fairly luminous. The EL spectra were collected from each pixel on the substrate, the emission peak wavelength was about 510 nm and the full width at half maximum was about 170 nm. The low variation in emission intensity in the different pixels implies a small variation in thickness of the solution-coated layers. More specifically, if we assume a minimum diameter of 20 μm for an inkjetted electrolyte droplet, and a smallest inter-droplet distance of 10 μm, we attain a pitch of 30 μm, which corresponds to a high display resolution of 850 PPI. Finally, we draw attention to the herein presented static-display LEC that comprises solely air-stabile materials, and that we routinely fabricate the bilayer stack under ambient atmosphere.Open in a separate windowFig. 7(a) The patterned light emission from a bilayer LEC, with the emission pattern defined by the selected positions of the ink jetted electrolyte droplets. (b) The droplet diameter and pitch were 50 and 150 μm, respectively, and the device was driven at V = 3 V. The scale bar measures 300 μm.     

Colour-tunable ultralong organic phosphorescence upon temperature stimulus

A new class of single-component molecular crystal with colour-tunable ultralong organic phosphorescence (UOP) was designed and synthesized through alkyl chain engineering. Forming a more rigid environment at 77 K, the colour-tunable UOP from yellow-white to blue-green is achieved through dual-emission of crystal and amorphous states.

A new class of single-component molecular crystal with colour-tunable ultralong organic phosphorescence (UOP) was designed and synthesized through alkyl chain engineering.

Ultralong phosphorescence, a kind of phosphorescence that can be observed by the naked eye after removing the excitation source, has received great attention in the fields of sensing,¹ displays,² imaging,³ anti-counterfeiting⁴ and so on during the past years. Unfortunately, it is limited to inorganic materials because of the weak spin–orbit coupling (SOC) and strong non-radiative transition of pure organic materials.⁵ Compared with inorganic materials, however, organic materials have some excellent merits, such as inexpensive cost, relative safety to the environment, and soft preparation conditions.⁶ The realization of UOP becomes very significant. As mentioned above, UOP can be achieved by promoting intersystem crossing (ISC) through enhancing SOC and suppressing non-radiative transitions. In view of these factors, various strategies such as polymerization,⁷ H-aggregation,⁸ crystallization,⁹ host–guest doping,¹⁰ and freezing conditions¹¹ have been explored to achieve UOP with the unremitting efforts of scientific researchers.Intelligent-response organic luminescent materials can change their luminescent properties such as colour, lifetime, intensity, etc. after being stimulated by the external factor, such as mechanical forces, temperature, pH, light, solvent, etc., which have caught great attraction. The sensitivity of luminescent molecule to excitation wavelength, temperature or oxygen can be applied in sensors, optical recording and so on.^12–14However, the luminescence of these materials with intelligent-response are mostly limited to fluorescence or room temperature phosphorescence (RTP) with relatively short lifetimes.^15–18 Few samples display persistent luminescent feature.¹⁹ Most organic compounds can only tune their afterglow properties by changing molecular side groups or multi-component doping.^20–23 Therefore, the development of single component UOP materials with intelligent response remains a challenge. Inspired by the alkyl-chain engineering²⁴ and freezing conditions, herein we speculate that temperature response UOP might be induced by controlling the activity of the alkyl chain to regulate non-radiative transition rate. By means of reducing the temperature to restrict the molecular motions at amorphous state, colour-tunable UOP with temperature-response can be realized by dual-emission of molecules at both amorphous and crystalline states.In our previous study, MCzT crystals showed yellow UOP at RT.²⁵ The crystals showed the same UOP at 77 K with that at RT (Fig. 1a). Here, 9-(2-((4,6-dimethoxy-1,3,5-triazin-2-yl)oxy)ethyl)-9H-carbazole (MTOD) was designed and via alkyl chain attaching carbazole with a triazine core. The target molecule was characterized by ¹H NMR and ¹³C NMR (Fig. S1–S3^†). Its melting point reaches 130 °C. (Fig. S4^†) MTOD achieved a lifetime of up to 860 ms under ambient conditions. Surprisingly, the UOP changed from yellow-white to blue-green after the removal of the UV-lamp for several seconds at 77 K (Fig. 1b), demonstrating colour-tunable property of UOP with a low temperature stimulus.Open in a separate windowFig. 1Molecular structures and UOP photographs of MCzT (a) and MTOD (b).In order to explore the reasons for the colour-tunable UOP of MTOD at low temperature. The photophysical properties of MTOD in the crystal state were first investigated under ambient conditions. As shown in Fig. 2a, the photoluminescence (PL) spectrum of MTOD shows two main emission peaks at 375 and 413 nm and a shoulder at 435 nm. From the lifetime decay profiles (Fig. S5a^†), it was confirmed that they were all assigned to the fluorescence. Notably, the crystals of MTOD presented yellow afterglow after turning off the UV lamp. From the delayed phosphorescence spectrum, the main emission of MTOD was located at 414, 556 and 600 nm with lifetimes of 681.91, 860.56 and 860.59 ms, respectively (Fig. 2b and S5b^†). Among these, the emission around 414 nm is assigned to triplet–triplet annihilation (TTA) fluorescence originating larger π–π overlaps of carbazole groups from the crystal data (Fig. S6^†).²⁶ Remaining two emission peaks are attributed to UOP emission. From the phosphorescence excitation-emission spectra of MTOD, UOP can be efficiently excited from 260 to 380 nm, with the optimal excitation at 360 nm (Fig. S7^†).Open in a separate windowFig. 2Photophysical properties of MTOD at room temperature and at 77 K. (a) Steady-state photoluminescence (PL, blue dashed line) and phosphorescence (red solid line) spectra at RT and 77 K. Inset: photographs taken after removing excitation. (b) Time-resolved phosphorescence decay of the emission bands at 556 and 600 nm at room temperature, respectively. (c) Time-resolved phosphorescence decay of the emission bands at 478, 564 and 612 nm at 77 K, respectively. (d) PL (blue dashed line) and phosphorescence (red solid line) spectra at molten state.Subsequently, we measured the PL and phosphorescence spectra of MTOD at 77 K (Fig. 2a). The steady-state PL spectrum showed four peaks at 361, 376, 410 and 436 nm, with little change compared with its corresponding spectrum at RT. However, a new phosphorescence peak appears at about 480 nm with an intense emission than others, which displays an ultralong lifetime of 2.5 s. Obviously, the new emission peak plays an indispensable role in the colour-changed UOP at 77 K. The yellowish-white UOP observed by naked eyes at 77 K is generated by the combination of three phosphorescence peaks. However, as time goes by, only the blue-green afterglow at about 480 nm due to the shorter lifetime of long-wavelength phosphorescence can be observed.To find out the origin of this new peak at 480 nm, the PL and phosphorescence spectra of MTOD at molten state were measured as amorphous emission. As shown in Fig. 2d, the PL peak is located at 380 nm and the phosphorescence spectrum shows a broad band with a main peak at 484 nm. It is suggested that the new phosphorescence emission peak at 77 K may be attributed to amorphous state. Taken together, we deduce that the colour-tunable property of the crystal is possibly due to the presence of an amorphous state at low temperature.The X-ray single crystal diffraction of MTOD crystal was taken to explore the mechanism of UOP at room temperature. Abundant intermolecular and intramolecular interactions (Fig. 3a, S6, S8 and S9a^†) in the crystals strongly restrict the torsional molecular configuration. The dihedral angle between the triazine and carbazole groups is about 75° (Fig. S10^†). In the crystal of MTOD, the single molecule is limited by multiple intermolecular interactions, including C–H⋯N (2.681 Å), π-H⋯π (2.791, 2.876 Å), π-H⋯N (2.703, 2.711 Å) (Table S3^†). The rich intermolecular interactions are beneficial to limit molecular motions to suppress non-radiative transitions of excited molecules, leading to UOP. However, the amorphous molecules around the crystals with weak restriction displayed negligible phosphorescence at room temperature due to the strong motions of alkyl chains.Open in a separate windowFig. 3Intermolecular interactions (a) at room temperature and (b) at 100 K.Comparatively, the single crystal of MTOD molecule at 100 K was measured in order to explore the colour-changing mechanism of UOP at low temperature (Fig. 3b and S9b^†). By comparison, MTOD crystals exhibit more intermolecular interactions at 100 K and the distance become shorter. Molecular conformation of MTOD changed slightly, the dihedral angle between triazine and carbazole changed from 74.95° to 75.32° (Fig. S10^†). These increased interactions can constrain the molecules more effectively and the stronger restriction of alkyl chain and carbazole will further suppress non-radiative transitions, resulting in the much longer phosphorescence lifetime of over 1.0 s at low temperature. Compared with the molecules in the crystalline state, freezing condition can provide a more rigid environment to minimize the movement of the alkyl chain, greatly reducing the non-radiative transition rate at amorphous state, resulting in the lifetime of short wavelength phosphorescence at 478 nm up to 2.5 s.According to the above results, the photophysical process of colour-tunable phosphorescence can be described by Jablonski diagram as shown in Fig. 4. Upon photoexcitation, both electrons in amorphous and crystalline molecules transforms to lowest singlet states (S₁). Then, the electrons in S₁ would further transform to the lowest triplet (T₁) through ISC. At room temperature, amorphous molecules show strong molecular motions to facilitate the non-radiative transitions. However, crystalline molecules due to closely arrangement can exhibit phosphorescence through radiative decay. At 77 K, both excitons in amorphous and crystal states are dominated by radiative transitions, leading to colour-tunable UOP.Open in a separate windowFig. 4(a) Jablonski diagram of the relevant photophysical processes illustrating amorphous and crystalline UOP process at room temperature (top) and 77 K (bottom). (b) Phosphorescence spectra of MTOD at different temperature and (c) corresponding coordinates in CIE.In view of the interesting luminescent phenomenon, we have investigated a series of phosphorescent spectra of MTOD crystals at different temperatures ranged from 183 to 273 K. As shown in Fig. 4b, as the temperature increases, the phosphorescence intensity of the amorphous molecules gradually decreases. The colour variations of the MTOD crystals in response to the environmental temperatures are shown in the Commission International de l’Eclairage (CIE) coordinate diagram (Fig. 4c). As the temperature was gradually changed from 183 to 273 K, the UOP changed from green to yellow with good linearity of the CIE coordinates. This demonstrated that MTOD crystals may have potential in low temperature sensing.In conclusion, we synthesized a colour-tunable single-component UOP compound through alkyl chain engineering. Combined the spectral and single crystal analyses, it is indicated that colour-tunable UOP comes from dual-emission of molecules at amorphous and crystalline states. Low temperature provides better rigid effect on UOP of amorphous molecules than crystals, resulting in the UOP colour changed from yellow-white to blue-green. More interestingly, red-shifted UOP of MTOD crystals with the increase of temperature can be achieved, demonstrating its potential for temperature sensing. This study will provide a platform for the design of single-component UOP molecules with tunable colour emission and broadens its application field.     

Insight into trifluoromethylation – experimental electron density for Togni reagent I

3,3-Dimethyl-1-(trifluoromethyl)-1,3-dihydro-1-λ3,2-benziodoxole represents a popular reagent for trifluoromethylation. The σ hole on the hypervalent iodine atom in this “Togni reagent” is crucial for adduct formation between the reagent and a nucleophilic substrate. The electronic situation may be probed by high resolution X-ray diffraction: the experimental charge density thus derived shows that the short intermolecular contact of 3.0 Å between the iodine and a neighbouring oxygen atom is associated with a local charge depletion on the heavy halogen in the direction of the nucleophile and visible polarization of the O valence shell towards the iodine atom. In agreement with the expectation for λ3-iodanes, the intermolecular O⋯I–C_aryl halogen bond deviates significantly from linearity.

The experimentally observed electron density for the “Togni reagent” explains the interaction of the hypervalent iodine atom with a nucleophile.

A “halogen bond” denotes a short contact between a nucleophile acting as electron density donor and a (mostly heavy) halogen atom as electrophile;^1,2 halogen bonds are a special of σ hole interactions.^3–5 Such interactions do not only play an important role in crystal engineering;^6–11 rather, the concept of a nucleophile approaching the σ hole of a neighbouring atom may also prove helpful for understanding chemical reactivity.The title compound provides an example for such a σ hole based reactivity: 3,3-dimethyl-1-(trifluoromethyl)-1,3-dihydro-1-λ3,2-benziodoxole, 1, (Scheme 1) commonly known as “Togni reagent I”, is used for the electrophilic transfer of a trifluoromethyl group by reductive elimination. The original articles in which the application of 1¹² and other closely related “Togni reagents”¹³ were communicated have been and still are highly cited. Trifluoromethylation is not the only application for hypervalent iodine compounds; they have also been used as alkynylating¹⁴ or azide transfer reagents.^15,16 The syntheses of hypervalent iodanes and their application in organofluorine chemistry have been reviewed,¹⁷ and a special issues of the Journal of Organic Chemistry has been dedicated to Hypervalent Iodine Catalysis and Reagents.¹⁸ Recently, Pietrasiak and Togni have expanded the concept of hypervalent reagents to tellurium.¹⁹Open in a separate windowScheme 1Lewis structure of the Togni reagent, 1.Results from theory link σ hole interactions and chemical properties and indicate that the electron density distribution associated with the hypervalent iodine atom in 1 is essential for the reactivity of the molecule in trifluoromethylation.²⁰ Lüthi and coworkers have studied solvent effects and shown that activation entropy and volume play relevant roles for assigning the correct reaction mechanism to trifluoromethylation via1. These authors have confirmed the dominant role of reductive elimination and hence the relevance of the σ hole interaction for the reactivity of 1 in solution by ab initio molecular dynamics (AIMD) simulations.^21,22 An experimental approach to the electron density may complement theoretical calculations: low temperature X-ray diffraction data of sufficient resolution allow to obtain the experimental charge density and associate it with intra- and inter-molecular interactions.^23–25 Such advanced structure models based on aspherical scattering factors have also been applied in the study of halogen bonds.^26–30 In this contribution, we provide direct experimental information for the electronic situation in Togni reagent I, 1; in particular, we analyze the charge distribution around the hypervalent iodine atom.Excellent single crystals of the title compound were grown by sublimation.^§ The so-called independent atom model (IAM), i.e. the structure model based on conventional spherical scattering factors for neutral atoms, confirms the solid state structure reported by the original authors,¹² albeit with increased accuracy. As depicted in Fig. 1, two molecules of 1 interact via a crystallographic center of inversion. The pair of short intermolecular O⋯I contacts thus generated can be perceived as red areas on the interaction-sensitive Hirshfeld surface.³¹Open in a separate windowFig. 1Two neighbouring molecules of 1, related by a crystallographic center of inversion. The short intermolecular I⋯O contacts show up in red on the Hirshfeld surface³² enclosing the left molecule. (90% probability ellipsoids, H atoms omitted, symmetry operator 1 − x, 1 − y, 1 − z).The high resolution of our diffraction data ^¶ for 1 allowed an atom-centered multipole refinement^33,34 and thus an improved model for the experimental electron density which takes features of chemical bonding and lone pairs into account. Fig. 2 shows the deformation density, i.e. the difference electron density between this advanced multipole model and the IAM in the same orientation as Fig. 1.^|| The orientation of an oxygen lone pair (blue arrow) pointing towards the σ hole of the heavy halogen in the inversion-related molecule and the region of positive charge at this iodine atom (red arrow) are clearly visible. Single-bonded terminal halides are associated with one σ hole opposite to the only σ bond, thus resulting in a linear arrangement about the halogen atom. Different geometries and potentially more than a single σ hole are to be expected for λ3-iodanes such as our target molecule, and as a tendency, the resulting halogen bonds are expected to be weaker than those subtended by single-bonded iodine atoms.³⁵ In agreement with these theoretical considerations, the closest I⋯O contacts in 1 amount to 2.9822(9) Å. This distance is significantly shorter than the sum of the van-der-Waals radii (I, 1.98 Å; O, 1.52 Å (ref. 36)) but cannot compete with the shortest halogen bonds between iodine and oxygen^37,38 or iodine and nitrogen.^39–41Fig. 1 and ​and22 show that the C_aryl–I⋯O contacts are not linear; they subtend an angle C10–I1⋯O1′ of 141.23(3)° at the iodine atom. On the basis of theoretical calculations, Kirshenboim and Kozuch³⁵ have suggested that the split σ holes should be situated in the plane of the three substituents of the hypervalent atom and that halogen and covalent bonds should be coplanar. Fig. 3 shows that the C_aryl–I⋯O interaction in 1 closely matches this expectation, with the next oxygen neighbour O1′ only 0.47 Å out of the least-squares plane through the heavy halogen I1 and its three covalently bonded partners C1, O1 and C10.Open in a separate windowFig. 2Deformation density for the pair of neighbouring molecules in 1; the dashed blue and red arrows indicate regions of opposite charge. (Contour interval 0.10e Å⁻³; blue lines positive, red lines negative, green lines zero contours, symmetry operator 1 − x, 1 − y, 1 − z).Open in a separate windowFig. 3A molecule of 1, shown [platon] along O1⋯C1, and its halogen-bonded neighbour O1ⁱ. Symmetry operator 1 − x, 1 − y, 1 − z.The Laplacian, the scalar derivative of the gradient vector field of the electron density, emphasizes local charge accumulations and depletions and it allows to assess the character of intra- and inter-molecular interactions. A detailed analysis of all bonds in 1 according to Bader''s Atoms In Molecules theory⁴² is provided in the ESI.^‡ We here only mention that the electron density in the bond critical point (bcp) of the short intermolecular I⋯O contact amounts to 0.102(5)e Å⁻³; we are not aware of charge density studies on λ3-iodanes, but both the electron density and its small positive Laplacian match values experimentally observed for halogen bonds involving O and terminal I in the same distance range.⁴³The crystal structure of 1 necessarily implies additional contacts beyond the short halogen bond shown in Fig. 1 and ​and2.2. The shortest among these secondary interactions is depicted in Fig. 4: it involved a non-classical C–H⋯F contact with a H⋯F distance of 2.55 Å.Open in a separate windowFig. 4C–H⋯F contact in 1; additional information has been compiled in the ESI.^‡ Symmetry operators i = 1 − x, 1 − y, 1 − z; ii = 1 − x, 1 − y, −z.The topological analysis of the experimental charge density reveals that this non-classical C–H⋯F hydrogen bond and all other secondary contacts are only associated with very small electron densities in the bcps. Table S8 in the ESI^‡ provides a summary of this analysis and confirms that the I⋯O halogen bond discussed in Fig. 1 and ​and22 represents by far the most relevant intermolecular interaction.The relevance of this halogen bond extends beyond the crystal structure of 1: Insight into the spatial disposition of electrophilic and nucleophilic regions and hence into the expected reactivity of a molecule may be gained from another electron-density derived property, the electrostatic potential (ESP). The ESP for the pair of interacting molecules in 1 is depicted in Fig. 5.Open in a separate windowFig. 5Electrostatic potential for a pair of molecules in 1 mapped on an electron density isosurface (ρ = 0.5e Å⁻³; program MoleCoolQt^44,45). Fig. 5 underlines the complementary electrostatic interactions between the positively charged iodine and the negatively charged oxygen atoms. One can easily imagine to “replace” the inversion-related partner molecule in crystalline 1 by an incoming nucleophile.The ESP tentatively obtained for a single molecule in the structure of 1 did not differ significantly from that derived for the inversion-related pair (Fig. 5), and even the results from theoretical calculations in the gas phase for an isolated molecule²⁰ are in good qualitative agreement with our ESP derived from the crystal structure. In the absence of very short contacts, polarization by neighbouring molecules only has a minor influence on the ESP. The experimentally observed electron density matches the proven reactivity for the title compound, and we consider it rewarding to extend our charge density studies on related hypervalent reagents.     

Photoswitchable probe with distinctive characteristics for selective fluorescence imaging and long-term tracing

A photo-switchable and high-contrast bio-imaging indicator 4,4′-(1E,1′E)-(4,4′-(cyclopentene-1,2-diyl)bis(5-methylthiophene-4,2-diyl))bis(methan-1-yl-1-ylidene)bis(azan-1-yl-1-ylidene)bis(2-(benzo[d]thiazol-2-yl)phenol) (BMBT) has been demonstrated, by integrating photochromophore with excited-state intramolecular proton transfer (ESIPT) moiety. The ability of reversible emission switching enables arbitrarily selective labeling or concealing of cells simply by controlling light irradiation. Besides, when the emission was switched on, BMBT is demonstrated to exhibit unique characteristics of aggregation induced emission (AIE), providing a high on–off ratio for favorable bio-imaging. Thus, the non-labeling and easily-controlled selective imaging, as well as good biocompatibility indicates BMBT to be a favorable cell probe with great potentials for functional bio-imaging fluorophore.

In this work, a photoswitchable probe was synthesized by integrating a photochromophore with an excited-state intramolecular proton transfer (ESIPT) moiety. It was explored to be a favorable fluorophore for selective fluorescence imaging and long-term tracing.

Although there are many conventional fluorescent probes used for fluorescent imaging in the past few years,^1–5 such as rhodamine,⁶ cyanine dye,⁷ quantum dots,^8,9 and lanthanide probes,¹⁰ these fluorescent probes can only respond irreversibly to one event.^11,12 In comparison, photochromophores,¹³ which can reversibly response with UV and visible light,¹⁴ are more valuable fluorescent probes for regional optical marking of interested cells.^15,16 Because of their favourable characteristics, such as excellent thermal stability, good fatigue resistance and fast response time, diarylethenes derivatives have drawn wide spread concern of researchers.^17–20 Furthermore, the special optical properties of diarylethenes enable them to be suitable for long time and real time monitoring in bioimaging.The significance of targeted imaging of fluorescence probe for bio-samples in vitro or in vivo is well-known for their high sensitivity, non-invasiveness, real-time detection and especially selectivity.^21–24 However, the synthesis of these targeting materials is usually complicated. Moreover, for the same type of cells, no selectivity is demonstrated by these complex targeting agents.^21–24 Therefore, easy-prepared and easy-controlled non-labeling fluorescence imaging agents have always been pursued by both the industry and scientific communities. Among the above-mentioned photochromophores, diarylethenes are expected to be promising photochromic imaging candidates due to their favorable characteristics described in preceding paragraph. Prospectively, they can be used for selective long-term tracing if the photostability can be ensured.In our previous work, a series of AIE-active excited-state intramolecular proton transfer (ESIPT) complexes have been demonstrated to be good bio-imaging candidate with many advantages such as simple preparation, good biocompatibility, high quantum yields, fast cell staining as well as long-term anti-photobleaching.^25–27 Sometimes, ESIPT compounds exhibit dual emission, originated from keto and enol state, respectively. This caused extremely fast four-level photophysical cycle (E–E*–K*–K–E), mediated by intramolecular H-bonds immediately after photoexcitation, enables two emissions.^28,29 Herein, we have demonstrated a new type of multifunctional bio-imaging materials based on facile synthesis design concept, by introducing a photochromic diarylethene moiety to enable regional emission turn-on, and introducing an ESIPT moiety to allow good photo stability for long-term tracing. To the best of our knowledge, this is the first example with integrating abilities of non-labeling selectively long-term regional tracing.The new diarylethene derivative (BMBT, see the molecular structure in Scheme 1) has been synthesized (Fig. S1^†) via condensation reaction of 5-amino-2-(benzo[d]thiazol-2-yl)phenol with 4,4-(cyclopentene-1,2-yl)-bis(5-methyl-thiophene-2-formaldehyde), according to a previous reported procedure.^30,31 The molecular structures and purities were confirmed by ¹H NMR spectroscopy and mass spectroscopy (Fig. S6 and S7,^† see the synthesis details and full molecular characterizations in the ESI^†).Open in a separate windowScheme 1Structure and photochromic process of BMBT.The photoirradiation-induced changes in absorption and fluorescence spectra at room temperature are investigated in THF/DMEM mixture (1.0 × 10⁻⁵ mol L⁻¹). The open-ring isomer mainly exhibits two absorption peaked at 304 and 380 nm, respectively (Fig. S2^†). This is ascribed to the internal charge transfer and π–π transition of 2-(2′-hydroxy-phenyl)benzothiazole (HBT),^10,30 coupled with the CT inside the HBT unit from the hydroxyphenyl ring to the benzothiazole ring (Scheme 1). BMBT exhibits two emissions; one blue emission peak around 458 nm and a red emission peak around 600 nm, corresponding to the enol and keto emission, respectively (Fig. 1). Upon irradiation with ultraviolet light at 365 nm, the absorption band at longer wavelength region centered at 595 nm increased obviously with irradiation time (Fig. S2^†). This is caused by the formation of the closed-ring isomer (see the photochromic reaction in Scheme 1). Correspondingly, due to spectroscopic overlap between this longer-wavelength absorbance with the red emission ranged from 560–700 nm, the relative intensity of the red emission substantially decreases with the UV irradiation (Fig. 1), because of efficient energy transfer. Upon further visible light (λ = 520 nm) irradiation, the closed-ring isomer transfers back to the initial open-ring isomer, and thus the longer-wavelength absorption decreases and the red emission restores. This indicates good reversibility of the photochromic reaction.Open in a separate windowFig. 1Fluorescence emission changes of BMBT in THF/DMEM (1 : 200, vol : vol) mixture upon irradiation with 365 nm light (λ_ex = 385 nm) and visible light (λ_ex = 520 nm).Excitingly, BMBT exhibit prominent characteristics of Aggregation-Induced Emission (AIE).^31–33 The fluorescence intensity of BMBT in THF solution was relatively weak, while the powder or nanoparticles of the material dispersed in DMEM buffer exhibited a significantly enhanced emission (Fig. 2). When the DMEM buffer fraction was increased gradually from 0% to 20%, the fluorescence intensity only slightly enhanced. When the DMEM fraction was further increased to 40%, the emission exhibits a significant enhancement. The total intensity at the blue enol emission increased more than 10 times at 100% DMEM fraction as compared with that in THF solution. This AIE property enables high signal-to-noise ratios for favorable bioimaging (Fig. S3^†).Open in a separate windowFig. 2Fluorescence spectra of 1 × 10⁻⁵ M BMBT in the THF/DMEM mixture at different water fractions (λ_ex = 385 nm).Based on the good reversibility of light response and AIE characteristics, the practical application of the BMBT as bioprobe was further investigated. The biological imaging of BMBT was observed by using confocal laser scanning microscopy (CLSM). Blue luminescence in the cytoplasm of HeLa cells was observed after incubation with a THF/DMEM (1 : 200, vol : vol) solution of BMBT (20 μM) for 30 min at 37 °C (Fig. 2 inset). The overlay of luminescent images and bright-field images confirmed that BMBT was located mainly in the cytoplasm of cells rather than the membrane and nucleus (Fig. S3^†). Intense intracellular luminescence with a high signal-to-noise ratio (I₁/I₂ > 7) was detected between the cytoplasm (regions 3 and 1) and nucleus (region 2), also implying weak even few nuclear uptake of BMBT (Fig. S4^†). Besides, BMBT has a low cytotoxicity with the cellular viabilities estimated to be greater than 85% after 24 h incubation with the highest cultural concentration of 50 μM BMBT (Fig. S5^†).The luminescence switching of BMBT can also be achieved while alternating UV and visible light illumination in fixed HeLa cells. Cells (shown in red circle, Fig. 3a) were irradiated with 488 nm light (0.5 mW) for 3 min, the blue fluorescence of the irradiated cells was lamped off while the surrounding cells remained almost unchanged. Such fluorescence quenching is likely ascribed to the intramolecular fluorescence resonance energy transfer of BMBT, due to the intensified short-wavelength absorption band (270–450 nm) of the closed-open form of BMBT with the blue emission band (420–560 nm).³⁴ Upon irradiation with 405 nm light (1.25 mW) the fluorescence of all the selected cell was rapidly recovered within 1 min, caused by decrease of the relative intensity of the 270–450 nm absorption. The fluorescence can be repeatedly erased and recovered many rounds without significant fluorescence quenching, which was hardly achieved by conventional fluorophores (Fig. 3b).^35,36Open in a separate windowFig. 3(a) CLSM image (above) and the overlay image (bottom) of fixed HeLa cells incubated with 20 μM BMBT for 30 min at 37 °C (1) and (5) in original state; (2) and (6) irradiated by 488 nm light (0.5 mW) for a single cell; (3) and (7) all cells, and; (4) and (8) recovered by 405 nm light (1.25 mW). (b) Fluorescence switching of fixed HeLa cells by alternating UV (405 nm, 1.25 mW, 10 s/time) and visible (488 nm, 0.5 mW, 3 min/time) light illumination (λ_ex = 405 nm).This characteristic of selectively opto-marking or de-marking of cells may be used for non-invasive and dynamic tracing of the interested objects in vitro. That is, BMBT can arbitrarily opto-label or de-label interested cells without affecting cell proliferation. As shown in Fig. 4, the cell marked in the red circle was treated with visible light illumination (488 nm, 0.5 mW, 3 min), and its fluorescence was effectively quenched. Cells division of the remaining “bright” cells was observed under the microscope field of vision for a long-term tracing with time up to 36 h. Multiple new cells were produced, as indicated by upper white arrow. Even, as indicated by bottom white arrow, the tacked cells were observed to be doubled. The high brightness of the fluorescence in the proliferated cells indicated the good photo stability of BMBT. This indicated that BMBT can be used as a cell marker for arbitrarily selective erasing the fluorescence of the designated cell. It can also be used for selective lighting their emission by making them as the remaining bright cells after selective photo-erasing or selective photo-recovering after full erasing. This long-term tracking with non-labeling and selective optically marking or de-marking is seldom reported by other photochromophore-based bioimaging agents.³⁷ Herein, the excellent anti-photo bleaching characteristic in the long-term tracing is attributed to high photo stability of the HBT moiety.^26,27Open in a separate windowFig. 4Cells was treated with visible (488 nm, 0.5 mW, 3 min) light illumination for erasing the fluorescence. The remaining bright cells were incubated for another 36 hours, which were observed to be amplified normally (λ_ex = 405 nm).     

Electrochemical preparation system for unique mesoporous hemisphere gold nanoparticles using block copolymer micelles

Gold nanoparticles (AuNPs) are widely used in various applications, such as biological delivery, catalysis, and others. In this report, we present a novel synthetic method to prepare mesoporous hemisphere gold nanoparticles (MHAuNPs) via electrochemical reduction reaction with the aid of polymeric micelle assembly as a pore-directing agent.

Mesoporous hemisphere Au nanoparticles using self-assembled micelles, for the first time, are demonstrated by using electrochemical reduction on a Ti substrate.

Gold (Au) is one of the most stable and versatile elements utilized in various fields, including catalysis, optics, and industrial purposes. Consequently, various shapes and sizes of AuNPs have been intensively studied to improve the performance of Au in different applications.^1–6 Previously, nanoporous or dendritic metal nanostructures, including Au nanostructures, have been synthesized by employing different reagents and conditions such as SH-terminated amphiphilic surfactant,⁷ pH controlling,⁸ and hard-templates.^9,10 The reported porous and dendritic Au nanostructures possess high surface areas and rich active sites, which in turn lead to highly enhanced catalytic activities.Recently, a soft-template method using self-assembled micelles or lyotropic liquid crystals as pore-directing agents has allowed the successful synthesis of mesoporous nanoparticles^11–13 and films^14–17 with different metal compositions. The metals with mesoporous structures demonstrate superior catalytic activity per weight or surface area over their nonporous bulk forms. Previously, our group reported a several-fold increase in the catalytic activity of mesoporous metals in reactions such as the methanol oxidation reaction (MOR),^14,15 ethanol oxidation reaction (EOR),^13,15–17 and nitric oxide reduction¹² as compared to their bulk nanoparticles and films. Such improvement in the catalytic activity of mesoporous structures is mainly attributed to their significantly larger surface areas, more exposed catalytically active sites, and increased durability against aggregation.Interestingly, nanoporous or mesoporous Au structures had been successfully synthesized by using a dealloying method¹⁸ and a hard templating method.⁹ Such methods, however, are a little complicated, and pore-directing templates often remain within the pores, thus leading to severe contamination. Using a thiol group is an alternative way to synthesize mesoporous Au nanospheres.⁷ A significant drawback of using a thiol group, however, is its strong chemical bonding with Au, thus becoming unable to be removed. The synthesis of mesoporous structures using self-assembled polymeric micelles as soft-templates, on the other hand, is a more facile method with fewer synthetic steps, and it is also known to be free of contaminations within the pores. Although a soft-templating method using polymeric micelles has been utilized for the preparation of mesoporous Au and Au-based alloy films towards surface-enhanced Raman scattering (SERS) signals,¹⁹ glucose sensing,^20,21 and MOR,²² the obtained morphologies have been limited to only films.Despite such apparent benefits arising from mesoporous structures and their synthesis using soft-templates, the synthesis of mesoporous AuNPs using soft-templates has not been achieved yet. It is mainly due to the physical and chemical properties of Au which make it extremely hard to form mesoporous structures. Herein, we adopt an electrochemical approach and the soft-template method to synthesize MHAuNPs successfully. As discussed above, we expect MHAuNPs to be highly efficient in various applications in medical diagnosis,²³ optical sensing,²⁴etc.In this report, MHAuNPs with different shapes and sizes are for the first time reported by changing various electrochemical deposition conditions such as applied potentials between electrodes and deposition times. Scheme 1 shows the schematic illustrations of the entire process of precursor preparation (Scheme 1a) and the MHAuNPs fabrication process (Scheme 1b), including the deposition and the detachment of the nanoparticles. The characterization methods implemented in this paper are mentioned in ESI.^†Open in a separate windowScheme 1(a) The process of Au precursor solution preparation and (b) fabricating MHAuNPs by electrochemical reduction.In a typical experiment, a p-doped silicon (Si) wafer was cleaned by using acetone, isopropyl alcohol, and deionized water (DIW) with sonication for 5 minutes, followed by nitrogen (N₂) gas blowing to dry the Si wafer. After the wet cleaning process, the Si surface was treated by oxygen (O₂) plasma for 5 minutes (Oxford Instruments PlasmaPro 80 Reactive Ion Etcher) to remove residual organic impurities. Then, 10 nm of titanium (Ti) layer and 100 nm of Au layer were deposited sequentially by electron beam evaporation (Temescal FC-2000 e-beam evaporator) at 10⁻⁶ torr. Commercially available Au etchant (Sigma-Aldrich) was used to etch the Au film to expose the Ti area (the left image in Scheme 1b). During etching, about 20 percent of Au area was left to be connected to the electrochemical work station, as drawn in Scheme 1b. In preparation of the Au precursor solution, 5 mg of poly(styrene)-block-poly(ethylene oxide) (PS-b-PEO, the number of average molecular weight (M_w) for each block is 18 000 for PS and 7500 for PEO, respectively) was mixed in 1.5 ml of tetrahydrofuran (THF) followed by stirring at 300 rpm for 8 hours. Then, 0.75 ml of ethanol, 0.5 ml of HAuCl₄ aqueous solution (40 mM), and 1.25 ml of DIW were added sequentially. The solution was stirred for another 30 minutes at 200 rpm. The existing block copolymer micelles can be confirmed by TEM observation, and the average diameter is 25 nm, as shown in Fig. S1.^† For the electrochemical deposition, an electrochemical workstation (CH Instruments Inc. 660e) with three electrode system was used to deposit MHAuNPs on the Ti/Si substrate. After the deposition, the particles were carefully washed by chloroform, followed by a rinse using DIW to remove the residual micelles completely. To detach and collect MHAuNPs from the Ti/Si substrate, the substrate was soaked in ethanol and strongly sonicated for a few minutes (Scheme 1b).Fig. S2^† shows the details of the growth mechanism of MHAuNPs by different deposition times. At the initial stage (Fig. S2a^†), small nanoparticles are generated by reducing Au ions in the precursor solution throughout the substrate. Then, the seed starts growing and forming MHAuNPs as the deposition time increases (Fig. S2b–e^†). This similar growth mechanism is the same as the previous report.¹⁹ The high-angle annular detector dark-field scanning transmission electron microscopy (HAADF-STEM) image (Fig. S2f^†) shows the mesopores inside the MHAuNPs are homogeneously generated. As-obtained MHAuNPs consist of a pure Au element without any impurities, as shown in Fig. S3.^† Fig. 1 and S4^† show scanning electron microscope (SEM) images of MHAuNPs deposited at different voltages from −0.2 V to −0.9 V vs. Ag/AgCl at high magnification and low magnification, respectively. Different deposition voltages lead to significant changes in the particle sizes but slight differences in the particle shapes. The size distributions of MHAuNPs and the plots of the average diameters of MHAuNPs by different deposition voltages are described in Fig. 2. The distribution graphs show the large sizes of particles, such as more than 1 μm in diameter, when the high voltage (−0.2 V vs. Ag/AgCl) is applied (Fig. 2a). The distribution becomes narrower upon the lower applied voltage. The average diameter-applied voltage plots in Fig. 2b show that the average particle size decreases from around 1.1 μm at −0.2 V to about 300 nm at −0.9 V. Thus when the lower deposition voltages are applied (i.e., the deposition rate is higher) (Fig. 1g–h), the smaller particles with a higher degree of size uniformity are obtained. The opposite trend is observed at higher deposition voltages (i.e., the deposition rate is lower) (Fig. 1a and b), at which the particles become larger and their size uniformity decreases. This trend is because the higher voltage allows only a limited number of seed particles to be deposited on the Ti/Si substrate, and each seed individually grows with no additional seed formation. Whereas the lower voltage can allow a higher number of seeds, leading to a uniform supply of electrons from the working Ti/Si electrode (Fig. S5^†). In addition, the lower deposition voltages make the particle shape more hemispherical in Fig. 1f–h.Open in a separate windowFig. 1The SEM images of MHAuNPs electrochemically deposited at (a) −0.2 V, (b) −0.3 V, (c) −0.4 V, (d) −0.5 V, (e) −0.6 V, (f) −0.7 V, (g) −0.8 V, and (h) −0.9 V for 500 s. The scale bars indicate 200 nm.Open in a separate windowFig. 2(a) Size distributions of MHAuNPs generated by different voltages and (b) the average diameter–the applied voltage plots. Fig. 3 shows the SEM images of MHAuNPs deposited at −0.2 V and for different deposition times from 250 s to 1000 s. Although longer deposition time does not change the number of MHAuNPs, it leads to the growth of MHAuNPs in lateral and vertical directions. Although the MHAuNPs grow more than about two or three times larger at long deposition time, the mesoporous formation does not seem to be changed, as shown in insets in Fig. 3. This point indicates that the deposition time is not the main factor affecting the formation of mesoporous structures as well as the number of particles (seeds), but it affects the sizes of particles.Open in a separate windowFig. 3The SEM images of MHAuNPs deposited at −0.2 V (vs. Ag/AgCl) for (a) 250 s, (b) 500 s, and (c) 1000 s. The scale bars indicate 10 μm. The insets in each figure are magnified SEM images of each condition (The scale bars in insets indicate 500 nm).In this report, 10 nm Ti layer on Si wafer plays an important key role in the formation of MHAuNPs, as previously mentioned in the experimental procedure. The use of the Ti substrate with low conductivity (ca. 2.38 × 10⁶ S m⁻¹), which is about only 5.8% in comparison with that of Au (ca. 4.10 × 10⁷ S m⁻¹), is not common in the electrochemical plating research field.^25–30 Most of the papers on mesoporous metal structures synthesized by electrochemical deposition have utilized Au or Pt substrates due to its chemical stability and high electrical conductivity.^14–17 Fig. S6^† shows the amperometry (i–t) curves during the deposition of MHAuNPs (black dots) on a Ti/Si substrate and mesoporous gold films (red dots) on an Au substrate at the same deposition condition. As shown in Fig. S6,^† around 1/7 times less current flows on the Ti/Si substrate throughout the deposition time. This low current density on the Ti/Si substrate is one of the factors for fabricating MHAuNPs. Low current density causes the formation of a few particles (i.e., seeds) at the initial stage of the deposition and leads to seed growth in a few places, as explained in Fig. S2.^† Furthermore, the use of Ti/Si substrates affects the bottom parts of MHAuNPs to become an arch shape. Only edges of MHAuNPs attach onto the Ti/Si substrates, as shown in Fig. 4. This attachment is because the interaction between the deposited MHAuNPs and the Ti substrate surface (probably, the Ti surface can be partially oxidized, forming TiO_x) is very weak. Therefore, the deposited MHAuNPs can be easily detached from the Ti/Si substrates by sonicating the substrates in solvents (Scheme 1b). The collected MHAuNPs in a solvent are obtained as colloidal particles as shown in Fig. S7.^† Such interesting hemispherical mesoporous nanoparticles have advantages to electrocatalytic activities in comparison to spherical mesoporous metals.³¹ The method using a Ti/Si substrate as a working electrode can be repeatedly implemented with one substrate and without change of the precursor solution, thus it can be effective for mass production in the future.Open in a separate windowFig. 4The SEM image of MHAuNPs deposited at −0.6 V. The arrow shows that the bottom of the MHAuNPs is an arch.Finally, surface-enhanced Raman scattering (SERS) effects on MHAuNPs were investigated by using an adsorbate called rhodamine 6G (R6G), as shown in Fig. S8.^† The resulting MHAuNPs at all conditions (−0.3 V, −0.6 V, and −0.9 V) show substantially strong SERS intensity (Fig. S8a^†), while Ti/Si and Si substrates without MHAuNPs show noise level of intensity. To further investigate enhancement factor (EF) and limit of detection (LoD), various concentrations of R6G with MHAuNPs fabricated at −0.9 V were used for the SERS studies (Fig. S8b^†). The main peak of SERS is 1363 cm⁻¹, and it disappears from less than 10⁻⁶ M concentration, while the 1183 cm⁻¹ peak still exists at 10⁻⁸ M (Fig. S8c^†). The maximum EFs at 1363 cm⁻¹ (10⁻⁶ M) and 1183 cm⁻¹ (10⁻⁸ M) are 1.5 × 10⁴ and 3.1 × 10⁶, respectively (Fig. S8d^†). Transmission electron microscope (TEM) images in Fig. S9^† show the detailed particle structures and the electron diffraction (ED) pattern confirmed the crystal structure is the face-center cubic (FCC) structure. The sharp surface structures and the pores on MHAuNPs provide abundant hot spots that have been reported as the origin that enhances SERS intensity owing to the plasmon resonances.^19,32 Besides, the high density of small-sized MHAuNPs (Fig. S5 and S10^†) boosted higher SERS intensity.In conclusion, we have synthesized MHAuNPs by using 10 nm Ti-coated Si substrates as a working electrode on a Si wafer and electrochemical deposition using self-assembled polymeric micelles as pore-directing agents. The low current generates Au seeds at only a few places, and it acts as the points that MHAuNPs start growing. The particle shapes and sizes can be controlled by changed applied voltages and deposition times. The lower voltages make small particles and the great hemispherical AuNPs with mesoporous architecture. The long-time deposition does not affect any mesoporous formation, but the particle shape and size. Besides, the low affinity between Au and Ti (probably, oxidized layer) results in the arch on the bottom of MHAuNPs, which helps the particles detached from the substrates easily. These results indicate that different thicknesses and compositions of working electrodes can provide different metal deposition phenomena, which can bring out unique shaped particles with mesoporous architectures in the future.     

Photocatalytic degradation of organic pollutants through conjugated poly(azomethine) networks based on terthiophene–naphthalimide assemblies

A conjugated poly(azomethine) network based on ambipolar terthiophene–naphthalimide assemblies has been synthesized and its electrochemical and UV-vis absorption properties have been investigated. The network has been found to be a promising candidate for the photocatalytic degradation of organic pollutants in aqueous media.

A conjugated two-dimensional poly(azomethine) network based on ambipolar terthiophene–naphthalimide assemblies has been synthesized and its electrochemical and UV-vis absorption properties have been investigated.

Due to the rapid growth of urbanization and intensive industrialization, pollution has evolved into a serious concern that produces a great negative impact on human health and the environment.^1,2 Therefore, many efforts are currently devoted to addressing environmental remediation through the degradation and removal of hazardous contaminants.^3–5 In this regard, photocatalysis has been identified as a suitable approach for environmental remediation given that it is an energy efficient technique that does not require chemical input and does not produce sludge residue.⁶ In recent years, organic semiconducting polymers have evolved into a new type of metal-free and heterogeneous photocatalyst suitable for solar-energy utilization.⁷ The modularity of organic polymers allows the efficient tunning of their electronic and optical properties by bottom-up organic synthesis through the choice of suitable monomeric building blocks.^8–10 Within this context, there is a growing demand for new organic polymeric semiconductors carefully designed to have suitable energy levels of the frontier orbitals, an appropriate bandgap and good intrinsic charge mobility.¹¹For the design of suitable polymeric semiconductors for photocatalysis, it is not only important that the photocatalysts absorb light in the visible light range but also an efficient dissociation of the photogenerated charge carriers is required. The combination of electron-poor acceptor (A) and electron-rich donor (D) moieties in the polymer structure may prevent a fast recombination process following photoexcitation.¹² In addition, it has been found that polymers networks bearing conjugated moieties may exhibit π-stacked columns that can facilitate charge transport.¹³In this respect, molecular and polymeric materials based on the combination of oligothiophene^14,15 and naphthalimide moieties^16,17 connected through conjugated linkers have shown to be very effective in order to efficiently tune their frontier orbital levels and produce tunable organic semiconductors with good charge transport properties.^18–24 As an example, in Fig. 1 is depicted the structure of NIP-3T, an ambipolar organic semiconductor, for which the one-electron HOMO–LUMO excitation consists of the displacement of the electron density from the HOMO, primarily localized on the oligothiophene fragment, to the LUMO, localized on the naphthalimide unit.²⁵Open in a separate windowFig. 1(a) Monomer containing an electron donor terthiophene system directly conjugated with an electron acceptor naphthalimide moiety through a conjugated pyrazine linker (NIP-3T). (b) HOMO and (c) LUMO computed orbital topologies for NIP-3T.²⁵Among conjugated polymers, poly(azomethine)s have found application as organic semiconductors in heterogeneous photocatalysis because of their π-conjugated system and suitable band levels matching the redox window of water.²⁶ The incorporation of D–A monomeric assemblies into poly(azomethine) networks represents an efficient strategy to obtain ambipolar polymeric networks with tunable frontier orbital levels for photocatalytic applications. Thus, in this communication we report the synthesis of a novel donor–acceptor poly(azomethine) network (NIP3T-ANW, Scheme 1) based on NIP-3T monomers. The potential of this system as photodegrading agent for the elimination of contaminant organic dyes in aqueous media is also explored.Open in a separate windowScheme 1Schematic representation of the synthesis of NIP3T-ANW.The synthesis of the macromolecular poly(azomethine) network NIP3T-ANW is acomplished through Schiff-base reactions between trigonal monomers endowed with amine functionalities (TAPB,²⁷Scheme 1) and linear naphthalimide–thiophene-based monomers endowed with complementary aldehyde functional groups (NIP3T2CHO,²⁴Scheme 1). Typically, both monomers were dissolved in an o-dichlorobenzene/n-butanol/acetic acid (1 : 1 : 0.1) mixture, which was then heated at 120 °C under solvothermal reaction conditions for 72 h. A black solid was obtained which was insoluble in common solvents such as water, acetone, THF, toluene or chlorinated solvents like dichloromethane or chloroform. The obtained solid was washed several times with THF to remove the starting materials and low-molecular weight by-products. After drying under vacuum, a black solid was obtained. The yield, as determined by weight, was 98%.To investigate the chemical nature of the material, as well as to determine the conversion of the functional groups after the reaction, we have employed attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy (Fig. 2). The bands arising from the NH₂ stretching (3000–3400 cm⁻¹) and NH₂ deformation (1650 cm⁻¹) vibrations of the primary amine group of TAPB and the signals from the aldehyde groups of NIP3T2CHO around 2870 (C–H stretching) and 1663 cm⁻¹ (C O stretching) are virtually absent in the NIP3T-ANW spectrum. In addition, a prominent new band is found at 1573 cm⁻¹, which can be assigned to the C N stretching vibration of the imine linkages within the newly formed poly(azomethine) network.^28–30Open in a separate windowFig. 2(a) IR spectra of NIP3T2CHO (blue), TAPB (red) and NIP3T-ANW (black). (b) Solid-state ¹³C CP-MAS NMR spectrum of NIP3T-ANW.Solid-state ¹³C cross-polarization magic angle spinning NMR (¹³C CP-MAS NMR) spectrum (Fig. 2) reveals the characteristic imide signals of the 1,8-naphthalimide moiety at 164.4 ppm, as well as the signal corresponding to the imine carbon at 154 ppm and a signal at 148 ppm which can be assigned to the aromatic carbon neighbouring the nitrogen of the C N group. The absence of the sp² carbons from the NIP3T2CHO ²⁴ aldehyde functionalities above 180 ppm satisfactorily confirms the condensation between the aldehyde and the amine derivatives.Due to the rigidity and geometry of the building blocks, the imine linkers could be ideally generated in such a way that result in a canonical layered hexagonal structure³¹ as predicted by theoretical calculations (Fig. S1 and S2^†). However, in the actual framework, X-ray diffraction (XRD) measurements indicate that the material is mainly amorphous with only some ordered regions, as indicated by the good agreement between the weak and broad diffraction peaks observed at 2θ values larger than 3 and those predicted by calculations for the ideal canonical layered hexagonal structure (Fig. S3^†). In this regard, NIP3T-ANW was submitted to an exfoliation process following a previously described protocol³² for the exfoliation of two-dimensional polymers (see ESI^† for details). The exfoliated material was analysed by dynamic light scattering (DLS) showing a monomodal size distribution of ca. 400 nm (Fig. S4^†) and transmission electron microscopy (TEM) reveals a sheet-like structural aspect (Fig. S5^†).Thermogravimetric analysis of the poly(azomethine) network NIP3T-ANW shows that the degradation starts at around 450 °C and only 40% weight loss is observed at 700 °C (Fig. S6^†). This thermal stability is significantly higher than that observed for NIP3T (Fig. 1), the analogous molecular system based on terthiophene connected with naphthalimide through pyrazine for which the degradation starts at 200 °C (Fig. S6^†).^22,25In photocatalysis mediated by semiconductors, electron–hole pairs (excitons) are generated after light absorption and afterwards dissociate into free charge carriers that can be utilized for redox reactions^33,34 such as CO₂ fixation,³⁵ water splitting³⁶ or organic mineralization.³⁷ Some of the crucial factors that make the photocatalytic process favourable are the levels of conduction and valence as well as the width of the band gap.^38–40 Thus, in order to characterize these parameters, the electrochemical and optical properties of NIP3T-ANW have been analysed.The electrochemical properties of NIP3T and NIP3T-ANW were studied by cyclic voltammetry (Fig. 3). Both materials show ambipolar redox behaviour in which the reversible reduction processes are characteristic of the naphthalimide unit, while the oxidation processes can be ascribed to the conjugated oligothiophene moiety.^19–22,24 For NIP3T-ANW, the first reversible reduction wave (−1.29 V) is shifted to less negative values in comparison with NIP-3T (−1.41 V). On the other hand, the first oxidation half wave potential for NIP3T is observed at +0.41 V and for NIP3T-ANW at +0.44 V. These shifts agree with the electron acceptor ability of the imine linker.Open in a separate windowFig. 3(a) The UV-vis DRS spectra of NIP3T and NIP3T-ANW. (b) Cyclic voltammetry of the NIP3T monomer and the corresponding polymer.The absorption spectrum of NIP3T-ANW as determined by UV-vis diffuse reflectance spectroscopy (UV-vis DRS, Fig. 3) shows a strong absorption in all the UV-vis range, extending even to the near infrared. This broad absorption is red-shifted in comparison with the one observed for NIP3T (Fig. 3), which reflects the formation of the new polymer network with an extended conjugation through the alpha positions of the terthiophenes.Using the corresponding cut-off wavelengths, the optical band gaps E_g found for NIP3T and NIP3T-ANW are 1.59 and 1.42 eV respectively. This optical result suggests that the incorporation of the NIP3T core into an extended conjugated system efficiently harvests photons from the visible range, even extending into the near IR region.To shed some light into the degree of crystallinity of the synthesized NIP3T-ANW network, we have carried out a battery of density functional theory (DFT)-based calculations with the QUANTUM ESPRESSO plane-wave DFT simulation code⁴¹ (see details in ESI^†). We have considered periodic boundary conditions to obtain a fully-relaxed ground-state crystal structure. Optimization of the cell-shape and size, simultaneously to the relaxation of the structure, reveals a hexagonal 2D lattice with an optimized parameter of 48.46 Å. Different interlayer stacking fashions have been tested, with only one yielding a good agreement with the experimental diffractogram from 2θ values >3°. The most favourable stacking predicted by theory consists in an intermediate configuration between the perfectly eclipsed and staggered configurations, with an interlayer distance of 3.42 Å, and permits an adequate accommodation of the layers profiting adjacent pores. Details on the structure can be found in the ESI.^†Additionally, we have computed the electronic band diagram of the obtained crystal structure along the high-symmetry k-path Γ → K → M → Γ, revealing a wide-gap (1.91 eV) semiconducting character, with rather dispersive valence and conduction bands, mainly resembling the molecular HOMO and LUMO of the molecular building blocks (see Fig. S7^†). Besides, computed time-dependent DFT (TDDFT) UV-vis spectrum manifests an excellent agreement with the experimental UV-vis spectra (Fig. S8^†). A broad and pronounced peak-feature is obtained between 600 and 800 nm, centred at around 720 nm (1.7 eV), which agrees with the optical gap of 1.6 eV found for NIP3T from Fig. 3a. This feature corresponds to electronic transitions between the valence and conduction bands, with an energy difference of around 0.2 eV between the optical and the electronic gap, which indicates that charge relaxation in excited states is not much significative. The good agreement between theoretical predictions on the canonically periodic computed system and the experimental evidences seems to justify the presence of some high-crystallinity regions from the synthesis.The band gap of a semiconductor material and the reduction and oxidation potentials are key parameters which determine its light-harvesting properties and types of reaction that can be conducted and therefore the overall photo-catalytic activity. A shift in the adsorption edge of a semiconductor towards longer wavelengths implies a narrower band gap and the efficient harvesting of a wider photons range.⁴²NIP3T-ANW seems to be an appealing material to be utilized as photocatalyst given (i) the optimal light harvesting properties as shown by the optical characterization, (ii) the efficient generation of electron–hole pairs owing to the insertion of terthiophene moieties, and (iii) the right energy band positions for the material.⁷ We therefore evaluated the photocatalytic activity of NIP3T-ANW under white light for the degradation of a model organic pollutant (Rhodamine B dye, RhB) in aqueous solution.⁴³ In the absence of catalyst, RhB remains stable in solution under illumination (Fig. 4a and S9^†). However, in presence of NIP3T-ANW nearly 90% of RhB in an aqueous solution is degraded after 120 min, showing the enhanced catalytic activity of the material (Fig. 4a and S10^†). Furthermore, a good stability is shown upon 4 straight catalytic cycles (Fig. 4b, S11 and S12^†). In contrast, in the presence of the NIP3T moiety, only a 55% degradation of RhB is observed in the same timeframe (Fig. 4a and S11^†).Open in a separate windowFig. 4RhB degradation curves. (a) Comparison between the degradation effect of NIP3T, NIP3T-ANW and without catalyst. (b) NIP3T-ANW stability after four recycling cycles.In the photocatalytic degradation of organic pollutants, they are typically broken down through the attack of superoxide and hydroxyl species, formed when atmospheric oxygen reacts with photogenerated electrons or when water or OH ions are oxidized by holes, respectively.⁴⁴ Additionally, electron–hole pairs (or excitons) can directly reduce or oxidize organic pollutants in aqueous environments. Consequently, the evaluation of the photodegradation mechanism of organic pollutants, despite challenging, can provide meaningful insights about the nature of a semiconductor photocatalyst.⁴⁵ With the aim of evaluating the photodegradation mechanism we performed the measurements in the presence of different scavengers, namely an aqueous solution of AgNO₃ (100 mg L⁻¹), which captures photogenerated electrons, or triethanolamine (TEOA), which traps photogenerated holes (Fig. S13^†).^46,47 In the presence of Ag⁺ we could observe that the photocatalytic efficiency is enhanced, while the addition of TEOA quenched the performance, therefore suggesting that holes are the active specie in the photodegradation mechanism (Fig. S14^†).In summary, we have presented an approach towards the incorporation of D–A π-conjugated monomeric assemblies into poly(azomethine) networks to yield a purely organic semiconductor for the photocatalytic degradation of organic pollutants in aqueous media. The poly(azomethine) network benefits from a straightforward poly(condensation) approach which favourably competes with the elaborate high-temperature protocols applied for the preparation of inorganic materials. This work enriches the family of donor–acceptor organic semiconductor networks and, given its modular nature, paves the way for the development of a promising family of materials for photocatalytic applications.     

Highly dispersed Pt nanoclusters supported on zeolite-templated carbon for the oxygen reduction reaction

The formation of highly dispersed Pt nanoclusters supported on zeolite-templated carbon (PtNC/ZTC) by a facile electrochemical method as an electrocatalyst for the oxygen reduction reaction (ORR) is reported. The uniform micropores of ZTC serve as nanocages to stabilize the PtNCs with a sharp size distribution of 0.8–1.5 nm. The resultant PtNC/ZTC exhibits excellent catalytic activity for the ORR due to the small size of the Pt clusters and high accessibility of the active sites through the abundant micropores in ZTC.

Electrochemically synthesized highly dispersed Pt nanoclusters (PtNCs) stabilized by the nanocages of zeolite-templated carbon (ZTC) exhibit excellent electrocatalytic performance toward the oxygen reduction reaction.

Platinum (Pt) is currently considered one of the best electrocatalysts for the oxygen reduction reaction (ORR), which occurs at the cathode of a fuel cell and is the key process determining the overall performance.^1–5 However, the high cost and scarcity of Pt limit its wide commercialization in this field. According to the US Department of Energy, the total Pt loading is required to be below 0.125 mg cm⁻², in contrast to a presently used Pt loading of 0.4 mg cm⁻² or more for fuel cell application.⁴ Therefore, reducing the Pt loading without loss or with an improvement of the cathode performance has received significant interest in electrocatalytic research for fuel cell systems.^6–10 In this regard, reducing the size of Pt particles to a nanocluster scale (size < 2 nm) and maximizing the Pt dispersion may offer an efficient way to achieve maximum utilization of the Pt electrocatalyst with appropriate consumption.^4,11–15The size of nanomaterials generally plays a critical role in controlling the physical and chemical properties for catalytic applications.^16–20 With a decrease in the particle size to the nanoscale, quantum size effects are induced, which alter the surface energy of the material due to unsaturated coordination and change in the energy level of the d orbital of metal atoms, leading to spatial localization of the electrons.^17–20 This size-induced effect on the electronic structures at the active sites modifies the capability of binding the reactant molecules in catalytic reactions, thereby altering the activity of the nanocatalyst.²⁰ When the particle contains a few to several dozens of atoms with sizes, ranging from sub-nanometer to 2 nm often termed as nanocluster that bridges nanoparticle and a single atom.²¹ However, the Pt single atom is not an appropriate electrocatalyst for the ORR in a fuel cell system as the fast four-electron (4e⁻) pathway for the reduction of O₂ to H₂O requires at least two neighboring Pt atoms.^22,23 Anderson''s group demonstrated that the ratio between the production of H₂O (product of 4e⁻ process) and H₂O₂ (2e⁻) in the ORR strongly depends on the number of atoms in the Pt cluster. Typically, it requires more than 14 atoms in a Pt cluster to produce H₂O efficiently through the 4e⁻ pathway of the ORR.²⁴ Therefore, Pt nanoclusters having more than a dozen atoms have proven to be highly efficient ORR electrocatalysts for fuel cell systems.^13–15 Upon decreasing the size of the nanoparticles to a nanocluster, the electronic state and structure are known to be changed, leading to an increase of the catalytic activity in the ORR. Therefore, it is highly desirable to synthesize a Pt nanocluster-based material as an ORR electrocatalyst with high catalytic performance. To date, several synthesis strategies, such as wet-chemical, atomic-layer deposition, and photochemical methods, have been applied for the preparation of well-dispersed Pt nanoclusters on different types of support, such as dendrimer, metal oxide, and carbon materials.^{13–15,25–31}An alternative approach to synthesize Pt nanocluster (PtNC) is the encapsulation of the cluster within nanosized pores, for example, by utilizing microporous (diameters less than 2 nm) carbon materials.³² Among the microporous carbons, zeolite-templated carbon (ZTC) has been attractive for supporting Pt clusters due to its ordered microporous structure.^33–37 ZTC is a potentially promising material as catalyst support as it offers the advantages of extremely large surface area and high electrical conductivity of graphene-like carbon frameworks constituting a three-dimensional (3D) interconnected pore structure.³⁶ Moreover, the micropores of ZTC can serve as nanocages for stabilization of the Pt nanoclusters. Coker et al. used Pt²⁺ ion-exchanged zeolite as a carbon template to synthesize Pt nanoparticles in ZTC with size in a range of 1.3 to 2.0 nm.³³ Recently, atomically dispersed Pt ionic species was synthesized via a simple wet-impregnation method on ZTC containing a large amount of sulfur (17 wt%).²³ Itoi et al. synthesized PtNC consisting of 4–5 atoms and a single Pt atom in ZTC using the organoplatinum complex.³⁷ Although these methods produced Pt nanoclusters with narrow size distribution and atomic dispersion, they required multi-step processes and/or high-temperature treatment (>300 °C). High-temperature treatment often induces the sintering of nanoclusters to aggregated clusters. Therefore, it is highly desirable to develop a simple and low-cost method for the preparation of PtNC supported on ZTC (PtNC/ZTC) for use as an efficient ORR electrocatalyst. The electrochemical reduction approach offers an alternate and efficient route for the synthesis of PtNC in the micropores of ZTC. The electrochemical method is one of the popular ways to prepare electrocatalysts because it is a simple single-step procedure and ensures electrical contact between the nanoparticles and the support.^38,39Herein, we report a facile electrochemical method for the formation of PtNC with a narrow size range of 0.8–1.5 nm supported on ZTC. The resultant PtNC/ZTC shows higher electrocatalytic activities towards ORR compared to that of commercial Pt/C. Here, ZTC plays two important roles: (i) it provides nanocages to stabilize the PtNC and (ii) it accelerates the ORR activity by enhancing the accessibility of active sites through its abundant micropores. Fig. 1a shows a schematic representation of the typical electrochemical synthesis of PtNC/ZTC. In the first step, ZTC was impregnated with a Pt-precursor dissolved in a water–ethanol mixture. As ZTC possess ordered micropores (Fig. S1a^†) with high Brunauer–Emmett–Teller (BET) surface area of 3400 m² g⁻¹ (vide infra), the uniform adsorption and anchorage of PtCl₆²⁻ ions into the micropores of ZTC was favored. After impregnating and drying, the resultant ZTC–PtCl₆²⁻ was mixed with water–ethanol and Nafion to make the ink for the preparation of the electrode. Using the prepared electrode, a potential of 0.77 V vs. reversible hydrogen electrode (RHE) (Fig. 1b) was applied followed by potential cycling between 1.12 to −0.02 V vs. RHE until the cyclic voltammogram was stabilized. The Pt content of PtNC/ZTC was determined to be ∼10 wt% (Fig. S2^†) by thermogravimetric analysis (TGA). The obtained PtNC/ZTC was electrochemically characterized by cyclic voltammetry and electrochemical impedance spectroscopy. The cyclic voltammogram (Fig. 1c) after potential cycling in fresh KOH electrolyte shows the characteristic Pt peaks corresponding to hydrogen adsorption and desorption. The Nyquist plots (Fig. 1d) demonstrate that PtNC/ZTC has lower electrolyte resistance (42 Ω) than that of ZTC (70 Ω), implying an improvement in the conductivity of ZTC by the presence of PtNC. Due to the increase in the conductivity, PtNC/ZTC could facilitate the electron transfer more effectively than ZTC, enhancing its electrocatalytic activity.Open in a separate windowFig. 1(a) Illustration for the formation of PtNC/ZTC:Pt-precursor was impregnated into ZTC micropores, and then a potential (0.77 V vs. RHE) was exerted on the ZTC–PtCl₆²⁻ composite in a 0.1 M KOH solution to form PtNC/ZTC (b) Chronoamperometric response of ZTC–PtCl₆²⁻ at a constant potential of 0.77 V (vs. RHE) in 0.1 M KOH electrolyte. (c) Cyclic voltammogram of PtNC/ZTC in a fresh 0.1 M KOH at a scan rate of 20 mV s⁻¹. (d) Nyquist plots of ZTC and PtNC/ZTC in 0.1 M KOH. Fig. 2a and b show images from aberration-corrected scanning transmission electron microscope (STEM) with high-angle annular dark-field (HAADF). The HAADF-STEM images exhibit the typical morphology of the final product (PtNC/ZTC) after electrochemical reduction. As shown in Fig. 2a, it is very clear that isolated PtNCs are uniformly dispersed in ZTC. These PtNCs have a homogeneous distribution with a narrow size range (0.8–1.5 nm, Fig. 2b). On further magnification, the STEM image shows a cluster-like structure of Pt (Fig. 2c). The STEM image of selected PtNC (Fig. 2d) reveals that it consists of ∼20 atoms. The number of atom content in PtNC was further determined by matrix-assisted laser-desorption-ionization time-of-flight (MALDI-TOF) mass spectrometry using trans-2-[3-(4-test-butylphenyl)-2-methyl-2-propenylidene]malononitrile as the matrix.^40,41 As shown in Fig. S3,^† MALDI-TOF measurement produces a mass spectra with a predominant peak centered at ∼3700 Da corresponding to the Pt₁₉ cluster. The TEM image (Fig. S4 a and b^†) validates the formation of PtNC with an average size of 0.9 nm. In addition, the energy dispersive X-ray spectrometer (EDS) mapping images clearly shows the uniform dispersion of Pt nanocluster in ZTC (Fig. S4c^†). The X-ray powder diffraction (XRD) pattern (Fig. 2e) of PtNC/ZTC showed three broad peaks associated with small size metallic Pt corresponds to (111), (200), and (311) planes (Fig. 2e, inset), along with peaks of ZTC at 2θ = 7.8° and 14.9° corresponding to the ordered microporous structure. Along with the structural analysis, the porous texture of PtNC/ZTC was examined by Ar adsorption (Fig. 2f). PtNC/ZTC had a high BET surface area of 2360 m² g_ZTC⁻¹, which is 1.4 times lower than that of pristine ZTC (3400 m² g_ZTC⁻¹). The decrease in Ar adsorption capacity after the formation of PtNC in ZTC is interpreted as a result of the filling of ZTC micropores by PtNC. This micropore filling was confirmed in the pore size distributions of the pristine ZTC and the metal-loaded carbon (inset of Fig. 2f). The X-ray photoelectron spectroscopy (XPS) results reveal the signature of Pt in ZTC (Fig. S5^†). The elemental survey (Fig. S5a^†) shows the signature of C 1s, O 1s, F 1s (Nafion), and Pt 4f. The chemical nature of Pt in PtNC/ZTC was inspected by a detailed Pt 4f XPS analysis. The deconvoluted Pt 4f XPS spectra (Fig. S5b^†) reveals the presence of both metallic and ionic Pt species. The peaks observed at 71.0 (4f_7/2) and 74.2 (4f_5/2) eV correspond to metallic Pt whereas the other peaks positioned at 72.6 (4f_7/2) and 76.0 (4f_5/2) are attributed to Pt²⁺ and the peaks at 74.9 (4f_7/2) and 77.8 (4f_5/2) eV are attributed to Pt⁴⁺ originating from the surface oxidation of metallic Pt.⁴²Open in a separate windowFig. 2(a–d) Representative spherical aberration-corrected HAADF-STEM images of PtNC/ZTC at various magnifications. (e) XRD pattern of PtNC/ZTC and (f) Ar adsorption–desorption isotherms of ZTC and PtNC/ZTC. Inset in (e) shows a 30 times magnified high-angle region of XRD of PtNC/ZTC. Inset in (f) shows the pore size distributions of the ZTC and PtNC/ZTC.The formation of narrow sized PtNC by the electrochemical method can be ascribed to the stabilization of PtNC in the ZTC micropores, which serve as cages to impose a spatial limitation on the size of the Pt clusters. For comparison, Pt supported on ZTC was also prepared by the conventional incipient wetness impregnation and subsequent H₂-reduction at high temperature (300 °C). The Pt obtained by this incipient wetness impregnation method shows the formation of Pt nanoparticles on the exterior surface of ZTC (PtNP/ZTC) (Fig. S6^†). The formation of larger Pt nanoparticles is due to the sintering at high temperature, showing that even ZTC micropores could not prevent the aggregation of PtNCs at high temperatures. Fig. 3 shows the electrochemical ORR activity of PtNC/ZTC using linear sweep voltammetry (LSV) technique on a rotating disc electrode (RDE) in a 0.1 M KOH solution saturated with O₂ at a scan rate of 5 mV s⁻¹. The ORR activity of ZTC (without PtNC) was measured for comparison as well. As shown in Fig. 3a, PtNC/ZTC exhibited higher diffusion limiting current density and higher positive onset and half-wave potential compared to ZTC alone, indicating that PtNC is the active center for the ORR. To investigate the effect of the Pt loading amount on the ORR activity, PtNC/ZTC with various Pt loadings, 2–20 wt%, was used for the measurement of LSV at 1600 rpm. With an increase in Pt content, both the onset and half-wave potential shifted towards more positive potential up to 10 wt% loading of Pt (Fig. 3a and S7^†). Upon further increase of loading of Pt on ZTC to 20 wt%, both the onset and half-wave potential of PtNC/ZTC shifted towards less positive potential along with a slight decrease in the diffusion limiting current density (Fig. 3a). The decrease in the ORR activity of PtNC/ZTC at high loading of Pt (20 wt%) was attributed to the decrease in the electrochemically active surface area (Fig. S8^†) and decrease in the specific surface area (Fig. S9^†). The STEM image clearly shows that the aggregated Pt clusters were formed on the exterior surface of ZTC at 20 wt% loading of Pt (Fig. S10c^†), blocking the accessibility of active sites. Therefore, PtNC/ZTC with the optimum loading of 10 wt% of Pt leads to superior ORR activity with a high positive onset potential of 0.99 V, which is similar to commercial Tanaka Pt/C (Pt/C-TKK) (Fig. 3b), and a half-wave potential of 0.87 V, which is ∼10 mV more positive than that of commercial Pt/C-TKK (0.86 V) (Fig. 3b). Compared to the case of PtNC/ZTC, both the onset and half-wave potential of PtNP/ZTC prepared by the conventional incipient wetness impregnation and subsequent H₂-reduction with the same loading of Pt exhibited a less positive value (Fig. S11^†). The poorer activity of PtNP/ZTC is due to the blockage of active sites by larger PtNPs formed on the exterior surface of ZTC (Fig. S6^†).Open in a separate windowFig. 3(a) RDE ORR polarization curves of PtNC/ZTC with different mass loading of Pt. (b) Comparison of PtNC/ZTC (PtNC_10%/ZTC) with commercial Pt/C-TKK at the same loading of 40 μg_Pt cm⁻². (c) RDE ORR polarization curves of PtNC/ZTC at different rotation speeds. Inset in (c) shows the corresponding K–L plots at different potentials. (d) Represents the kinetic current density values of Pt/C-TKK and PtNC/ZTC at the potential of 0.8 V vs. RHE.To investigate the kinetics of the ORR activity of PtNC/ZTC, LSV measurements were performed with RDE at different rotating rates (Fig. 3c), and the kinetics was analyzed using a Koutecký–Levich (K–L) plot (Fig. 3c, inset). From Fig. 3c, it was observed that the current density increases with the increasing speed of rotation of the electrode, which is characteristic of a diffusion-controlled reaction. The corresponding linear K–L plots (Fig. 3c, inset) with a similar slope at different potentials reveal that the number of transferred electrons was ∼4, indicating that O₂ is directly reduced to OH⁻ and the ORR is dominated by the H₂O₂-free 4e⁻ pathway. To estimate the amount of produced peroxide ion, rotating ring-disc electrode (RRDE) measurement was performed and the produce peroxide ion calculated from RRDE curve was < 4% (Fig. S12^†). The kinetic current density (J_k) obtained from K–L plot at the potential of 0.8 V (Fig. 3d) for PtNC/ZTC (J_k = 50 mA cm⁻²) is 2.2 times higher than that of commercial Pt/C-TKK (J_k = 22 mA cm⁻²).As Pt-based electrocatalysts are known to be highly active in an acidic medium, the ORR activity of PtNC/ZTC in O₂-saturated 0.1 M HClO₄ was also evaluated by comparing it with that of commercial Pt/C-TKK with the same loading of Pt on the electrode surface using RDE at a scan rate of 5 mV s⁻¹. The PtNC/ZTC-based electrode exhibited ORR activity with an onset potential of 0.96 V (Fig. 4), which is close to that of Pt/C-TKK (0.98 V), and half-wave potentials of 0.84 V, which is 20 mV more positive than that of Pt/C-TKK (0.82 V). PtNC/ZTC showed a slightly higher diffusion-limiting current density of ∼5.9 mA cm⁻² (0.4–0.7 V) compared with that of the Pt/C-TKK catalyst (∼5.6 mA cm⁻²). The kinetics of the ORR in an acidic medium was further analyzed using RDE at different rotation rates (Fig. S13^†) and it was observed that the current density increases with the increasing speed of rotation of the electrode, as in the case of the alkaline medium. The number of electron involved and the amount of produced H₂O₂ estimated by RRDE measurement were ∼4 and < 5%, respectively (Fig. S14^†). The mass activity of PtNC/ZTC obtained using the mass transport corrected kinetic current at 0.8 V is 0.15 A mg⁻¹, which is 3.2 times higher than that of Pt/C-TKK (0.046 A mg⁻¹).Open in a separate windowFig. 4(a) RDE ORR polarization curves at 1600 rpm and (b) mass activity at 0.8 V of PtNC/ZTC and Pt/C-TKK in 0.1 M HClO₄.Furthermore, the methanol tolerance of PtNC/ZTC was assessed by intentionally adding methanol to the oxygen saturated electrolyte solution (both in alkaline and acidic media). The commercial Pt/C-TKK was used for comparison as well. The peak current densities for methanol oxidation with PtNC/ZTC were ∼2.8 and ∼3 times lower than that of Pt/C-TKK in alkaline (Fig. 5a) and acidic (Fig. 5b) media, respectively. These results indicate that PtNC/ZTC has much higher tolerance towards methanol than Pt/C-TKK does. This higher methanol tolerance of PtNC/ZTC can be attributed to the small size of the Pt cluster, which may not be sufficient to catalyze the oxidation of methanol efficiently, as the oxidation of methanol requires Pt ensemble sites.⁴³Open in a separate windowFig. 5ORR polarization curves of PtNC/ZTC and Pt/C-TKK in the absence (solid line) and presence (dotted line) of 0.1 M of CH₃OH at a rotation rate of 1600 rpm in (a) alkaline and (b) acid media.The durability of PtNC/ZTC was also investigated by the amperometric technique. The test was performed at a constant voltage of the half-wave potential in an O₂-saturated alkaline medium and at 0.7 V in an O₂-saturated acidic medium at a rotation rate of 1600 rpm (Fig. S15a and b^†). The durability of the PtNC/ZTC catalyst in the alkaline medium was higher than that of Pt/C-TKK, exhibiting a 30% decrease compared to a 40% decrease of Pt/C-TKK in 5.5 h of ORR operation (Fig. S15a^†). The higher durability of PtNC/ZTC compared to Pt/C-TKK in the alkaline medium may be due to the stabilization of PtNC by pore entrapment. In the acidic medium, however, PtNC/ZTC exhibited a 54% decrease in the initial current after 5.5 h of operation while a 33% decrease was observed in the case of Pt/C-TKK (Fig. S15b^†). The decrease in ORR activity in the acidic medium may be due to the leaching out of tiny Pt nanoclusters in acid electrolyte from the ZTC micropores. To understand the decrease in the ORR durability with time, STEM measurements of PtNC/ZTC after 5.5 h of ORR operation were performed. In the alkaline medium, the STEM image of post-ORR PtNC/ZTC shows a slight change in the size of PtNC (Fig. S15c^†) while the STEM image of PtNC/ZTC after ORR in the acidic medium exhibited sintering of PtNC into large particles with an average size of 30 nm (Fig. S15d^†), resulting in a decrease of the ORR activity. In the alkaline medium, the decrease in ORR activity with time may be due to the oxidation of the ZTC support in KOH.⁴⁴We attributed the excellent ORR activity of PtNC/ZTC to the interplay between the following: (1) the structure of the Pt cluster possessing a high ratio of surface atoms that benefits the surface reactions,^45–47 (2) the microporous 3D graphene-like structure of the ZTC support that enables easy access of O₂ and electrolyte molecules to the active sites,⁴⁸ and (3) the high conductivity and large accessible surface area of ZTC that facilitates the electron transfer.^49–51     

Mesoporous-silica-coated palladium-nanocubes as recyclable nanocatalyst in C–C-coupling reaction – a green approach

We report the straightforward design of a recyclable palladium-core–silica-shell nanocatalyst showing an excellent balance between sufficient stability and permeability. The overall process – design, catalysis and purification – is characterized by its sustainability and simplicity accompanied by a great recycling potential and ultra high yields in C–C-coupling reactions.

A green approach: in a single-step coating process a mesoporous silica shell was tailored onto palladium-nanocubes. Along with a PEG-matrix this core–shell-nanocatalyst could be recovered after C–C-coupling reactions and reused without any significant decrease in product yield.

In contrast to bulk materials, metal-nanocyrstals (NC) possess unique physical and chemical properties. Both, nano-scale and geometry can dictate their optical, electronic and catalytic behavior.^1–3 Consequently, nanomaterials have been implemented already in various fields like medicine,⁴ sensing,⁵ nano-electronics⁶ and organic synthesis.⁷ Smart strategies for a sustainable usage of limited resources such as precious metals and hydrocarbons are inevitable due to the consistently growing population and economy.^8–10 Generally, catalysis gives rise to novel and energy-saving synthetic routes. However, homogeneous catalysis is not widely used in industrial processes, due to the need of mostly toxic ligands and the costly purification along with a restricted reusability potential.^11–13 Heterogeneous catalysis based on the utilization of metal nanocrystals overcomes most of these limitations. Caused by its high surface-to-volume ratio, catalytic activities are drastically increased in comparison to bulk materials. However, the most common disadvantage in NC-based catalysis lies in the occurrence of aggregates during the reaction, which leads to a decrease of the catalytic active surface. Several studies were already presented in literature to delay that phenomenon using micelle-like- or core–shell-nanostructures as potential nanocatalytic systems.^14–20 However, these surfactants or shells are either potentially harmful for the environment or very step-inefficient to produce. Other approaches used the deposition of small NCs in a mesoporous support which offers a large active surface area.^21–24 In this context, it is crucial to find an adequate balance between permeability for small organic molecules and the overall stability of the nanocatalyst. Overcoming these obstacles can contribute to a sustainable supply of drugs and other organic substances.In the present work palladium-nanocubes (Pd-NCubes) were fabricated in aqueous solution using cetyltrimethyl-ammoniumbromide (CTAB) as surfactant. The procedure is adapted from a previously published study.^25,26 The respective transmission electron microscopy (TEM) image and the selected area electron diffraction (SAED) pattern of the as-obtained Pd-NCubes are depicted in Fig. S1.^† The SAED confirms the single-crystallinity of Pd-NCubes bound by {100}-facets. TE micrographs of Pd-NCubes revealed an average edge-length of (18 ± 2) nm (for histogram see Fig. S2^†). The formation of polyhedra and nanorods was found to be less than 1%.To the best of our knowledge, there is no procedure reported that showed the direct fabrication of a mesoporous silica (mSi) shell tailored on Pd-NCs. However, Matsuura et al. demonstrated a single-step coating approach of CTAB-capped gold-nanorods and CdSe/ZnS quantum dots obtaining a mesoporous silica shell.²⁷ The pores were determined to be 4 nm in width with 2 nm thick walls. Since the Pd-NCubes are covered by CTAB, already no surfactant exchange is necessary. Consequently, this procedure could be directly transferred to the as-obtained Pd-NCubes (∼10¹⁵ particles per L) of this study using tetraethyl orthosilicate (TEOS) as silica precursor in an alkaline solution. Here, CTAB serves as organic template for the formation of the mesoporous silica shell.TE micrographs of individual Pd-mSi-nanohybrids are depicted in Fig. 1 showing a spherical silica coating with a thickness of (17 ± 2) nm (for histogram see Fig. S3^†). The porosity is essential to ensure that vacant coordination sites on the palladium-core are present and accessible for catalysis. In contrast to other multistep approaches, pores are formed in situ with no additional etching step necessary.^28,29 This avoids the usage of harmful etching agents such as fluorides or ammonia.³⁰ The silica shell then served as platform for further surface modification using two different PEG-silanes (M_n = 5000 g mol⁻¹ and M_n = 20 000 g mol⁻¹). TE microscopy did not reveal any changes in the structure of the PEG functionalized Pd-mSi-nanohybrids opposed to the unfunctionalized nanocatalyst, since the contrast of polymer is too low (see Fig. S4^†). However, dynamic light scattering (DLS) measurements in diluted aqueous solutions proved an increased hydrodynamic radius with increasing molecular weight of the PEG-chain grafted onto the silica shell (see Fig. 2). These results provide evidence that only individual nanostructures are formed while no larger aggregates are present.Open in a separate windowFig. 1Exemplary TE micrographs of Pd-mSi-nanohybrids.Open in a separate windowFig. 2DLS results along the different stages of the hierarchal fabrication process of the nanocatalyst.The successful functionalization of the Pd-mSi-nanohybrid with PEG provides the dispersibility for the overall nanocatalyst in a PEG matrix. Due to its lack of toxicity and its simple recovery, caused by its melting point at ∼50 °C, PEG is considered as a “green” reaction medium.³¹ It has already been shown that PEG can act as suitable solvent for both homogeneous and heterogeneous catalysis.^32–34 Consequently, further experiments were performed using only the Pd-mSi-nanohybrid functionalized with PEG-silane having an average molecular weight of M_n = 5000 g mol⁻¹ (PEG-5k). For catalytic reactions, Pd-mSi-PEG-5k was dispersed in a PEG matrix (PEG-2000, M_n = 2000 g mol⁻¹) and charged into a Teflon centrifuge tube. Using only one tube for the reaction and the product separation avoids an additional transfer step and prevents any loss of the nanocatalyst between reaction cycles (see recycling Scheme 1). Here, the C–C-coupling between ethyl acrylate and p-iodoanisole served as model Heck-reaction to prove the catalytic activity of the designed catalyst (4.4 mol% overall Pd conc. equal to ca. 0.3 mol% surface-available Pd; conc. is determined by ICP-MS measurements, see Table S1^†). Sodium phosphate was used as base providing the largest product yield when compared to other bases, such as Na₂CO₃, K₂CO₃ and K₃PO₄. Once the catalysis was performed and the PEG-2000 was cooled down, diethyl ether was added to extract the product and separated from the reaction medium via centrifugation.Open in a separate windowScheme 1Recycling process of the Pd-mSi-PEG-5k-nanocatalyst and PEG-2000 as solvent after the Heck-reaction between ethyl acrylate and p-iodoanisole to form ethyl p-methoxycinnamate.To exclude any suspended compounds from the desired product, the mixture was passed through a PTFE-filter. Et₂O was removed in vacuo without the need of column chromatography. Comparing the ¹H-NMR spectra of the as-obtained product with the educts indicate a yield of 98% with only small amounts of PEG-2000 present (identified by the signal at ∼3.6 ppm, < 1 weight-%). The results show that both educts and the base Na₃PO₄ are able to diffuse through the mesoporous silica shell to the palladium core (see Fig. 3). A detailed ¹H-NMR signal assignment of the product is given in Fig. S5.^†Open in a separate windowFig. 3 ¹H-NMR spectra of the educts ethyl acrylate (top) and p-iodoanisole (center) and the product ethyl p-methoxycinnamate (bottom).After recovering the reaction mixture containing Pd-mSi-PEG-5k and PEG-2000, seven further Heck-reaction-cycles were conducted under the same conditions. Results obtained from ¹H-NMR and gravimetry indicate no significant decrease in catalytic activity (see ¹H-NMR spectra in Fig. 4). Along the eight Heck-reactions, product yields were determined between 94% and 99%. Only small traces of p-iodoanisole (identified by the signal at ∼6.75 ppm) were still present while ethyl acrylate could be fully removed in vacuo. The yields obtained after each cycle are displayed in Fig. 5. ICP-MS measurements of the catalysis product were performed to determine the palladium leaching out of the catalytic system. The results are displayed in Table S1^† indicating that leaching is strongly suppressed since the overall Pd-content in the product ranges from 0.3–5.7 ng, only. This corresponds to 0.002–0.044 ppm palladium with respect to the product mass. The data are in good agreement with the high product yields along the eight Heck-reactions. To trace the evolution of the nanocatalyst along the cycles, TE micrographs were taken after the 1^st and the 8^th Heck-cycle (see Fig. 6). It can be seen that the cubical structure of the palladium vanishes during the first reaction (left TEM image). Inside the silica shell spherical palladium particles were formed. An explanation for this rearrangement lies in the suggested Heck-mechanism.³⁵ Here, a Pd²⁺-species forms after the oxidative addition of the p-iodoanisole which can desorb from the Pd-NCube. Once the reductive elimination of the product occurs the Pd⁰-species is generated again that can re-deposit on the palladium-core.²¹ Since the spherical geometry possesses the lowest free surface energy, globules were eventually formed.³ The mesoporous silica shell is not affected significantly by the catalysis and the rearrangement of the palladium. The porosity appears to stay intact, enabling the penetration of further small organic molecules. Control experiments were performed to validate whether these observations are based on either a thermally or a chemically induced rearrangement process of the palladium core. Therefore, only the nanocatalyst was dispersed in PEG-2000 and heated at 110 °C for 24 h without any conducted catalysis reaction. TEM results showed no changes in the structure of neither the palladium core nor the silica shell (see Fig. S6^†). After the 8^th reaction, no core–shell-nanostructures could be detected anymore via TEM. Only small randomly shaped Pd-nanoparticles (≤20 nm) were found indicating a slow leaching of the palladium out of the silica shell. However, no larger aggregates were formed (see right TE micrograph in Fig. 6) which explains the continuously high catalytic activity.Open in a separate windowFig. 4 ¹H-NMR spectra of the product ethyl p-methoxycinnamate after the 1^st Heck-reaction (bottom) up to the 8^th reaction (top).Open in a separate windowFig. 5Conversions of ethyl p-methoxycinnamate obtained via NMR and gravimetry after each respective Heck-reaction (1–8).Open in a separate windowFig. 6TE micrographs of the Pd-mSi-PEG-5k-nanocatalyst taken after the 1^st (left) and the 8^th Heck-reaction (right).     

Size effect studies in catalysis: a simple surfactant-free synthesis of sub 3 nm Pd nanocatalysts supported on carbon

Supported Pd nanoparticles are prepared under ambient conditions via a surfactant-free synthesis. Pd(NO₃)₂ is reduced in the presence of a carbon support in alkaline methanol to obtain sub 3 nm nanoparticles. The preparation method is relevant to the study of size effects in catalytic reactions like ethanol electro-oxidation.

A simple surfactant-free synthesis of sub 3 nm carbon-supported Pd nanocatalysts is introduced to study size effects in catalysis.

A key achievement in the design of catalytic materials is to optimise the use of resources. This can be done by designing nanomaterials with high surface area due to their nanometre scale. A second achievement is to control and improve catalytic activity, stability and selectivity. These properties are also strongly influenced by size.^1–3 To investigate ‘size effects’ it is then important to develop synthesis routes that ensure well-defined particle size distribution, especially towards smaller sizes (1–10 nm).Metal nanoparticles are widely studied catalysts. In several wet chemical syntheses, NP size can be controlled using surfactants. These additives are, however, undesirable for many applications^4,5 since they can block active sites and impair the catalytic activity. They need to be removed in ‘activation’ steps which can negatively alter the physical and catalytic properties of the as-produced NPs. Surfactant-free syntheses are well suited to design catalysts with optimal catalytic activity⁶ but their widespread use is limited by a challenging size control.³Palladium (Pd) NPs are important catalysts for a range of chemical transformations like selective hydrogenation reactions and energy applications.^7–9 It is however challenging to obtain sub 3 nm Pd NPs, in particular without using surfactants.² Surfactant-free syntheses are nevertheless attracting a growing interest due to the need for catalysts with higher performances.^10–14Promising surfactant-free syntheses of Pd NPs were recently reported.^8,15 The NPs obtained in these approaches are in the size range of 1–2 nm and show enhanced activity for acetylene hydrogenation⁸ and dehydrogenation of formic acid.¹⁵ Enhanced properties are attributed to the absence of capping agents leading to readily active Pd NPs. The reported syntheses consist in mixing palladium acetate, Pd(OAc)₂, in methanol and the reduction of the metal complex to NPs occurs at room temperature. The synthesis is better controlled in anhydrous conditions to achieve a fast reaction in ca. 1 hour. Another drawback is that the synthesis must be stopped to avoid overgrowth of the particles. Therefore, a support material needs to be added after the synthesis has been initiated and no simple control over the NP size is achieved.^8,15In this communication a more straightforward surfactant-free synthesis leading to sub 3 nm carbon-supported Pd NPs in alkaline methanol at ambient conditions is presented. A solution of Pd(OAc)₂ in methanol undergoes a colour change from orange to dark, indicative of a reduction to metallic Pd, after ca. a day. However, only ca. 1 hour is needed with Pd(NO₃)₂, Fig. 1 and UV-vis data in Fig. S1.^† The fast reduction of the Pd(NO₃)₂ complex in non-anhydrous conditions is a first benefit of the synthesis presented as compared to previous approaches.Open in a separate windowFig. 1Pictures of 4 mM Pd metal complexes in methanol without or with a base (as indicated).For particle suspensions prepared with Pd(OAc)₂ or Pd(NO₃)₂ the NPs agglomerate and quickly sediment leading to large ‘flake-like’ materials. When the reduction of Pd(NO₃)₂ in methanol is performed in presence of a carbon support and after reduction the solution is centrifuged and washed in methanol, a clear supernatant is observed indicating that no significant amount of NPs are left in methanol. Transmission electron microscope (TEM) analysis confirms that NPs are formed and well-dispersed on the carbon support surface and no unsupported NPs are observed, Fig. 2a. Likely, the reduction of the NPs proceeds directly on the carbon support. However, the size of the NPs is in the range 5–25 nm, which is still a relatively large particle size and broad size distribution.Open in a separate windowFig. 2TEM micrographs of Pd NPs obtained by stirring 4 mM Pd(NO₃)₂ in methanol and a carbon support for 3 hours, (a) without NaOH and (b) with 20 mM NaOH. Size distribution histograms are reported in Fig. S4.^† The same samples after electrochemical treatments are characterised in (c) and (d) respectively. Size distribution histograms are reported in Fig. S7.^†Assuming a ‘nucleation and growth’ mechanism, the NPs should become larger over time.¹⁶ But the reaction is so fast that by stopping the reaction before completion, size control is not achieved and unreacted precious metal is observed, Fig. S2.^† To achieve a finer size control and more efficient use of the Pd resources, a base was added to the reaction mixture, e.g. NaOH.³ In alkaline media, the formation of Pd NPs is slower; it takes ca. 60 minutes to observe a dark colour for a 5 mM Pd(NO₃)₂ solution with a base/Pd molar ratio of 10 in absence of a support, Fig. 1.Also in alkaline methanol, the NPs agglomerate over time in absence of a support material. However, if the alkaline solution of Pd(NO₃)₂ is left to stir in presence of a carbon support the desired result is achieved, i.e. Pd NPs with a significantly smaller size and size distribution of ca. 2.5 ± 1.0 nm, Fig. 2b. The NPs homogeneously cover the carbon support and no unsupported NPs are observed by TEM suggesting that the NPs nucleate directly on the carbon surface. Furthermore, the supernatant after centrifugation is clear, indicating an efficient conversion of the Pd(NO₃)₂ complex to NPs, Fig. S3.^† Furthermore, there is no need for an extra reducing agent as in other approaches, for instance in alkaline aqueous solutions.⁹The benefits of surfactant-free syntheses of Pd NPs for achieving improved catalytic activity have been demonstrated for heterogeneous catalysis.^8,15 Surfactant-free syntheses are also well suited for electrochemical applications where fully accessible surfaces are required for fast and efficient electron transfer. Several reactions for energy conversion benefit from Pd NPs. An example is the electro-oxidation of alcohols,⁷ in particular ethanol¹⁷ (see also Table S1^†).Previous studies optimised the activity of Pd electrocatalysts by alloying,^18–20 by using different supports^17,21–23 or crystal structures.^24,25 Investigating NPs with a diameter less than 3 nm was challenging.^2,26,27 The surfactant-free synthesis method presented here allows to further study the size effect on Pd NPs supported on carbon (Pd/C) for electrocatalytic reactions.In Fig. 3, results for ethanol electro-oxidation in 1 M ethanol solution mixed with 1 M KOH aqueous electrolyte are reported based on cyclic voltammetry (CV) and chronoamperometry (CA) with Pd/C catalysts exhibiting 2 significantly different size distributions. The electrode preparation, the measurement procedure and the sequence of electrochemical treatments are detailed in the ESI.^† In order to highlight size effects, we compare geometric and Pd mass normalized currents (Fig. 3a and c) as well as the oxidation currents normalized to the Pd surface area (Fig. 3b).Open in a separate windowFig. 3Electrochemical characterisation of carbon supported Pd NPs with 5–25 nm (grey) and 2.5 nm (dark) size in 1 M KOH + 1 M ethanol aqueous electrolyte. (a) 2^nd CV before chronoamperometry (CA), (b) current normalised by the electrochemically active surface area of Pd, (c) CA recorded at 0.71 V vs. RHE after 50 cycles between 0.27 and 1.27 V.It is clearly seen that based on the geometric current density, the smaller Pd NPs exhibit significantly higher currents for ethanol oxidation than the larger NPs. To differentiate if this observation is a sole consequence of the different surface area, the electrochemically active surface area (ECSA) has been estimated based on “blank” CVs (without ethanol) recorded between 0.27 and 1.27 V vs. RHE in pure 1 M KOH aqueous electrolyte and integrating the area of the reduction peak at ca. 0.68 V, Fig. S5.^† As conversion factor, 424 μC cm⁻² was used.²⁸Using this method, the smaller NPs with a size around 2.5 nm exhibit an ECSA of 92 m² g⁻¹ whereas the larger NPs with a size in the range 5–25 nm exhibit an ECSA of 47 m² g⁻¹, consistent with a larger size. Normalising the ethanol electro-oxidation to these ECSA values instead of the geometric surface area, Fig. 3b, still indicates a size effect. It is clearly seen that the smaller Pd NPs exhibit higher surface specific ethanol oxidation currents, in particular at low electrode potentials. Furthermore, a clear difference in the peak ratios in the CVs is observed. The ratio in current density of the forward anodic peak (j_f, around 0.9 V) and the backward cathodic peak (j_b, around 0.7 V vs. SCE) is around one for the smaller NPs, whereas it is about 0.5 for the larger NPs. The forward scan corresponds to the oxidation of chemisorbed species from ethanol adsorption. The backward scan is related to the removal of carbonaceous species not fully oxidised in the forward scan. The higher j_f/j_b ratio therefore confirms that the smaller NPs are more active for ethanol electro-oxidation and less prone to poisoning, e.g. by formation of carbonaceous species that accumulate on the catalyst surface.^29,30 This observation is further supported by a chronoamperometry (CA) experiment, Fig. 3c, at 0.71 V performed after continuous cycling (50 cycles between 0.27 and 1.27 V at a scan rate of 50 mV s⁻¹). In the CA testing of the thus aged catalysts at 0.71 V, the ethanol oxidation current on the two catalysts starts at around the same values, however, its decay rate is significantly different. The Pd mass related oxidation currents for the smaller NPs are after 30 minutes almost twice as high (ca. 200 A g_Pd⁻¹) as for the larger ones (ca. 130 A g_Pd⁻¹), confirming that the small Pd NPs are less prone to poisoning. In particular a factor up to 4 in the Pd mass related ethanol oxidation currents after 1800 s of continuous operation is achieved compared to a recently characterised commercial Pd catalyst on carbon,²⁰ Table S1.^† Despite different testing procedure reported in the literature, it can be concluded from these investigations that the surfactant-free synthesis presented shows promising properties for electrocatalytic ethanol oxidation even after extended cycling.The extended cycling, however, has different consequences for the two catalysts. For the small (2.5 nm) NPs of the Pd/C catalyst, a massive particle loss, but only moderate particle growth is observed as highlighted in Fig. 2 (see also Fig. S6^†). TEM micrographs of the two Pd/C samples recorded before and after the complete testing (CVs and CAs, for details see Fig. S7^†) show that the catalyst with small Pd NPs exhibits a pronounced particle loss as well as a particle growth to ca. 6 nm probably due to sintering. By comparison, for the Pd/C catalyst with the large Pd NPs, no significant influence of the testing on particle size or particle density is apparent.     

Complement activation by gold nanoparticles passivated with polyelectrolyte ligands

Gold nanoparticles passivated by polyelectrolyte ligands are widely used to confer stability and biofunctionality. While nanoparticles and polyelectrolytes have been reported as activators, their ability to activate the complement system as hybrid polyelectrolyte-coated nanoparticles is poorly characterized. Here, we found that gold nanoparticles passivated by common polyelectrolytes activated the system differently. The surface area of AuNPs appeared to be a major determinant of complement activation level as it determined the amount of adsorbed polyelectrolytes. Although a moderate negative correlation between AuNP surface hydrophilicity and their activation level was observed, the surface charge and functional group of polyelectrolyte ligands also influenced the final complement activation level.

We reported that the surface area and hydrophilicity of polyelectrolyte-coated gold nanoparticles influence their complement activation, a biological response not well understood to date.

Nanomaterials may elicit various biological responses upon contact with blood, of which activation of the complement system in innate immunity is one of the earliest.^1–3 The complement system is a collection of over 40 soluble and membrane-bound proteins, which acts in any of three distinct enzymatic cascades: classical, lectin, and alternative leading to the formation of a C3 convertase complex, and its accompanying range of biological responses, including inflammation, opsonization and cytolysis.^2,4While these responses could lead to undesirable physiological responses from over-activation and rapid clearance of nanomaterials from circulation, the intricate link between complement activation and adaptive immunity^5–7 also presents opportunities for exploitation in immune-related applications such as vaccines development. Therefore, complement activation by nanomaterials in biomedical applications has attracted great attention recently.^3,8–10We previously reported complement activation by gold nanoparticles (AuNPs) of different shapes in their as-synthesized citrate and CTAB coatings.¹¹ Polyelectrolyte ligands are also widely used in the preparation of AuNPs not only to stabilize AuNPs against aggregation, but to also enhance their solubility and confer additional surface functionalities.^12–14 These polyelectrolytes with different functional groups have been reported as complement activators in both their particulate and planar surface-immobilized forms.^15–21 However, the ability of polymer-passivated AuNPs to activate the complement system and the underlying mechanism remain poorly understood, although our previous study demonstrated that passivating the surface of AuNPs by poly(ethylene glycol) (PEG) modulated the activation level.¹¹Herein, we stabilized different shapes of AuNPs with different polyelectrolytes and examined their levels of complement activation and underlying mechanism. This would provide rational guidelines on the use of polyelectrolytes to modulate complement activation. All polyelectrolytes used in this study are hydrophilic and widely used as delivery platforms^5,22 and surface passivating ligands of nanomaterials²³ (Scheme 1).Open in a separate windowScheme 1Schematic illustration of gold nanoparticles (AuNPs) core, polyelectrolytes and methods used in this study. AuNPs with spherical shape of 20 nm (Au20) and 40 nm (Au40) as well as rod-shape (AuNR) were used as AuNP cores. These AuNPs were passivated with various polyelectrolyte ligands, examined for their hydrophilicities and levels of complement activation.Spherical AuNPs of two diameters, 20 nm (Au20) and 40 nm (Au40), were synthesized by well-known citrate reduction method.²⁴ AuNPs of rod-like shape (AuNR) were synthesized by hexadecyltrimethylammonium bromide (CTAB)-mediated method²⁵ with the CTAB ligands subsequently replaced by citrate using previously established protocol.²⁶ All AuNPs were then passivated by different polyelectrolytes following previously established layer-by-layer protocols (see Experimental section, ESI^†). With this library of AuNPs, we sought to examine the effects of size and shape of AuNP core as well as polyelectrolyte shell on the level of complement activation.The TEM images showed that Au20 and Au40 were spherical and homogenous while AuNR was rod-shaped with dimensions of approximately 40 × 10 nm (Fig. 1a–c). Hydrodynamic diameters, D_h, (Fig. 1d) were consistent with sizes of 20.2, 41.8, and 10.6 × 40.2 nm obtained from TEM images for Au20, Au40, and AuNR respectively (Fig. S1b–e, ESI^†). The UV-Vis absorption spectra showed surface plasmon resonance (SPR) peaks of 523 nm and 530 nm for Au20 and Au40, respectively while AuNR had transverse peak of 509 nm and longitudinal peak of 800 nm (Fig. S1a, ESI^†).^27,28 All citrate-capped Au20, Au40 and AuNRs had similar zeta potentials of −30 mV, which became nearly neutral after passivated with poly(vinyl alcohol) (ζ_AuNP-PVA ≈ −5 mV) and polyamidoamine (ζ_AuNP-PAMAM ≈ −10 mV) (Fig. 1e). In contrast, surface passivation with poly(acrylic acid) (AuNP-PAA), poly(styrenesulfonate) (AuNP-PSS), and heparin (AuNP-Heparin) conferred AuNPs a more negative zeta potential of ≈−40 mV (Fig. 1e), while coating with poly(ethyleneimine) (AuNP-PEI) conferred AuNPs a positive surface charge of ≈+40 mV. The presence of polyelectrolytes on AuNPs was further confirmed by the increase in D_h of polyelectrolyte-passivated AuNPs (Fig. 1d).Open in a separate windowFig. 1Physical properties of library of AuNPs. TEM images of (a) citrate-capped Au20, (b) Au40, and (c) AuNR. (d) Hydrodynamic diameter, D_h, and (e) zeta potential, ζ, of citrate-capped AuNPs and polyelectrolyte-passivated AuNPs. Each data point represents mean ± standard deviation (SD) of triplicate experiments. Scale bar in the TEM images represents 50 nm.When these polyelectrolyte-passivated AuNPs were incubated in normal human serum, the generation of SC5b-9 as an endpoint biomarker showed complement activation regardless of the activation pathway.^3,4,8 Here, elevated levels of SC5b-9 were detected in all AuNPs-treated sera (Fig. 2), indicating activation of the complement system. Prior to surface passivation by polyelectrolytes, we observed an expected complement activation by AuNP-citrate, although the level was significantly lower than our positive control zymosan (a well-known complement activator derived from the wall of yeast cell). Also, Au40-citrate induced more SC5b-9 than Au20-citrate and AuNR-citrate (Fig. 2).Open in a separate windowFig. 2Detection of endpoint product of complement activation, SC5b-9, using ELISA kit. 1× PBS and zymosan (10 mg ml⁻¹) were used as negative (−) and positive (+) controls, respectively. Each data point represents the mean ± standard deviation of triplicate experiments.The level of complement activation was dependent on both the AuNP core and polyelectrolyte ligand. Amongst the polyelectrolytes, we observed the highest level of complement activation from PEI, comparable or even higher than zymosan (Fig. 2). This agreed with previously published results where positively charged polymers carrying primary amino groups were shown to interact strongly with complement proteins to activate the complement system.^18,21Between the three AuNP cores, Au40-PEI had the highest level of complement activation ([SC5b-9] = 1.80 μg ml⁻¹), followed by Au20-PEI ([SC5b-9] = 1.29 μg ml⁻¹) and AuNR-PEI ([SC5b-9] = 1.16 μg ml⁻¹), which had comparable levels of complement activation (Fig. 2). The same trend was true not only for AuNPs-PEI but also other polyelectrolyte-passivated AuNPs. While complement activation by nanomaterials have been shown to depend on their sizes and shapes,^8,29 the differences observed here were more likely attributed to the amount of PEI adsorbed on the surface of AuNPs, which was in turn dictated by their surface area, since PEI by itself has been shown to activate the complement system in concentration-dependent manner.¹⁸ Here, Au20 and AuNR had comparable surface areas (1256 and 1413 nm², respectively) and hence similar levels of complement activation, while Au40 had the largest surface area (5024 nm²), thus accounting for the highest level of complement activation (Fig. 2).Unlike PEI, AuNPs passivated by both PVA and PAA induced the lowest levels of SC5b-9 (Fig. 2). While PVA is widely known as a biocompatible ligand on AuNRs,²³ its complement activation was not totally avoided probably due to its nucleophilic hydroxyl groups,^16,17 similar to PEI with nucleophilic amine groups. However, its complement activation level was much lower, and was likely due to its near neutral surface charge which did not promote interaction with many negatively charged complement proteins unlike the positively charged PEI.Similarly, the highly negative charge AuNP-PAA due to high density of carboxyl groups did not promote their interaction with negatively charged complement proteins, thus inducing an equally low level of complement activation as AuNP-PVA. Therefore, PAA is one of the most widely used water-soluble polyelectrolyte, superabsorbent polymer as well as food additive. Nonetheless, PAA conjugated to IgG has been found to specifically interact with positively charged C1q complement protein to activate the classical pathway.^30,31 Hence, AuNP-PAA has been found to promote inflammation via activation with fibrinogen.³² In this study, the AuNP-PAA could have activated the complement system via the classical pathway due to their interactions with C1q complement protein as reported.^30,31Owing to its nature as an anticoagulant, heparin has been reported to minimize complement activation.^33–35 However, we found that AuNP-heparin still activated the complement system although their level of complement activation was comparable to PVA and PAA, and much lower than PEI, PSS and PAMAM.Interestingly, despite the presence of nucleophilic amine groups on PAMAM similar to PEI, AuNP-PAMAM activated the complement system at much lower levels compared to AuNP-PEI. PAMAM dendrimers were known to be generation-dependent complement activators with stronger complement activation observed in higher generations.¹⁵ Here, we used PAMAM of generation 2.0 with aminoethanol surface and reasoned that coupling of amine with hydroxyl group helped to reduce activation level of AuNP-PAMAM. In fact, the activation level of AuNP-PAMAM was between that of AuNP-PVA with hydroxyl groups, and AuNP-PEI with amine groups. Furthermore, since primary amine groups adsorbed more C3b, a major component of complement proteins in serum, than secondary or tertiary amino groups,²⁰ the lack of primary amine group in PAMAM also explained its weaker complement activation than PEI which possesses a mixture of primary, secondary, and tertiary amine groups.The amount of SC5b-9 induced by AuNP-PSS was comparable to that of AuNP-PAMAM (Fig. 2). PSS is a widely used polyelectrolyte building block in layer-by-layer assembly,³⁶ and we used it as an intermediate ligand to prepare AuNR-citrate (Fig. S2, ESI^†). PSS by itself interacted with complement proteins of the classical pathway to activate the complement system.¹⁹ Our results not only confirmed complement activation by PSS passivation but also highlight the potential side effects of block-copolymer containing PSS commonly used as drug delivery platform in activating the complement system.Since the hydrophilicity of nanoparticles has been shown to modulate non-specific protein adsorption³⁷ and dictate immune response,³⁸ we further examined for possible correlation between the hydrophilicity of polyelectrolyte-passivated AuNPs and their level of complement activation. We measured relative hydrophilicity of polyelectrolyte-passivated AuNPs by dye absorption using a hydrophilic dye Nile Blue which interacted with a hydrophilic moiety (see Experimental section, ESI). On mixing the dye with AuNPs passivated with different polyelectrolyte ligands, we determined the partitioning quotient (PQ) as the ratio of dye bound on nanoparticles surface to the amount of free dye. In a plot of PQ versus surface area of nanoparticles, the slope of this linear regression line represented relative surface hydrophilicity.³⁹We observed different levels of hydrophilic dye adsorption on all polyelectrolyte-passivated AuNPs after 3 h incubation, indicating differences in their hydrophilicities (Fig. S8–10, ESI^†). AuNPs-PEI was the least hydrophilic (Fig. 3) as determined from the smallest slope of the linear regression line (Table S1, ESI^†), while AuNPs passivated with PVA, PAA, and heparin are amongst the most hydrophilic as given by the larger slope of the PQ vs. nanoparticle surface area plot (Fig. 3 and Table S1, ESI^†).Open in a separate windowFig. 3Negative correlation between surface hydrophilicity and complement activation by polyelectrolyte-passivated (a) Au20, (b) Au40 and (c) AuNR. X scale bar was plotted as ln of the value of relative hydrophilicity.We also observed a negative correlation between surface hydrophilicity and complement activation level across all AuNPs regardless of shape or size (Fig. 3). However, this correlation was only moderate with Pearson correlation coefficient, r = −0.2730, −0.4101, and −0.5489 for Au20, Au40 and AuNR, respectively (Fig. 3). Since Moyano et al. reported a positive correlation between nanoparticle surface hydrophobicity and their immune response previously,³⁸ the similarity in our observations suggested that the complement system could be a potential mediator between surface hydrophilicity/hydrophobicity and downstream immune response. Nonetheless, our results also demonstrated the complexity of complement activation by engineered nanomaterials, as it was not dependent solely on any one physical property such as shape, size, surface charge, surface functional group or surface hydrophilicity, but the interplay of these properties to influence the complement proteins adsorption.In summary, AuNPs passivated with different polyelectrolyte ligands activated the complement system at different levels, as characterized by the presence of endpoint product of complement activation, SC5b-9. The surface area of AuNPs appeared as a major determinant of complement activation level as it determined the amount of adsorbed polyelectrolytes. Although a moderate negative correlation between AuNPs surface hydrophilicity and their activation level was observed, the surface charge and functional group of polyelectrolyte ligands also influenced the final complement activation level. These findings provide new insights to rational selection and design guidelines for the use of polyelectrolytes to either suppress complement activation and downstream immune response for nanoparticulate drug delivery systems or to enhance complement activation and immune response for vaccine development.     

Coumarin-based fluorescent probe for the rapid detection of peroxynitrite ‘AND’ biological thiols

A coumarin-based novel ‘AND’ logic fluorescent probe ROS-AHC has been developed for the simultaneous detection of ONOO⁻ and biological thiols. ROS-AHC was shown to exhibit only a very small fluorescence response upon addition of a single GSH or ONOO⁻ analyte. Exposure to both analytes, however, resulted in a significant fluorescence enhancement.

A coumarin-based novel ‘AND’ logic fluorescent probe ROS-AHC has been developed for the simultaneous detection of ONOO⁻ and biological thiols.

Peroxynitrite (ONOO⁻) is a short-lived reactive oxygen and reactive nitrogen species (ROS and RNS) produced intracellularly by the diffusion-controlled reaction of nitric oxide (NO˙) with superoxide (O₂˙⁻).^1–3 Despite playing a key role as a physiological regulator,⁴ it is commonly known for its high reactivity towards most types of biomolecules, causing deleterious effects and irreversible damage to proteins, nucleic acids, and cell membranes.^5,6 ONOO⁻ is therefore a central biological pathogenic factor in a variety of health conditions such as strokes, reperfusion injuries or inflammatory and neurodegenerative diseases (Parkinson''s disease, Alzheimer''s disease).^7–9 Conversely, biothiols such as glutathione and cysteine are endogenous reducing agents, playing a central role in the intracellular antioxidant defence systems.^10–12 Glutathione (GSH), in particular, is the most abundant biothiol in mammalian cells, and exists as both its reduced GSH form, and as the oxidised disulphide form GSSG.^13–15 Peroxynitrite and biothiols such as GSH are intimately linked, as abnormal levels of highly oxidising ONOO⁻ can perturb the delicate GSH/GSSG balance, causing irreversible damage to key processes such as mitochondrial respiration.¹⁶ Thus, abnormal levels of GSH are common in cells undergoing oxidative stress, in which the regulation of and interplay between ONOO⁻ and GSH is closely associated with physiological and pathological processes.^17,18 One such example is drug-induced liver injury (DILI), in which upregulation of ONOO⁻ occurs in hepatotoxicity. Treatment with GSH could be used to remediate this type of cell injury by depletion of ONOO⁻.^19–22One of our core research interests lies in the development of dual analyte chemosensors capable of detecting two distinct analytes such as biological reactive oxygen species and biothiols.^23–26 Although a wide range of single-analyte probes exist for the detection of ROS and thiols separately,^27–30 ‘AND’ logic sensors for their simultaneous detection are still rare.^31–33 We are therefore interested in developing such probes, containing two distinct sensing units, one for each analyte, working simultaneously or in tandem to elicit a fluorescence response.³⁴ This approach allows the monitoring of multiple biomolecular events and factors involved in specific disease pathologies, in order to achieve optimal predictive accuracy for diagnosis and prognostication.³⁵Using these principles, our group has recently focused on developing a range of ‘AND’ logic based sensors exploiting a variety of sensing units and mechanisms of fluorescence. Two such probes are shown below: GSH-ABAH (Fig. 1a), an ESIPT probe with a 4-amino-2-(benzo[d]thiazol-2-yl)phenol (ABAH) core, employing a maleic anhydride thiol-acceptor group;³¹ and JEG-CAB (Fig. 1b), a coumarin-based probe, this time with a salicylaldehyde homocysteine-reactive unit.²⁴ Both of these sensors employ a benzyl boronate ester as their peroxynitrite-reactive unit.Open in a separate windowFig. 1(a) GSH-ABAH, previously reported probe for simultaneous detection of ONOO⁻ and GSH. (b) JEG-CAB, previously reported probe for simultaneous detection of ONOO⁻ and GSH. (c) AHC – a core fluorescent unit that enables the synthesis of ‘AND’ based fluorescent probe for the detection of ONOO⁻ and GSH (d) ROS-AHC, a novel probe detailed in this work for simultaneous detection of ONOO⁻ and GSH.Herein, we set out to develop an ‘AND’ logic gate based fluorescence probe for simultaneous detection of ONOO⁻ and GSH. 3-Amino-7-hydroxy-2H-chromen-2-one (AHC) was chosen as a suitable coumarin fluorophore core for the development of an ‘AND’ logic based sensor, as its free phenol and amine functional groups provided a good opportunity for independent derivatization (Fig. 1).^36–39Previous literature reports show that protection of AHC with a maleic anhydride group results in quenching of the coumarin''s fluorescence intensity due to photoinduced electron transfer (PeT) processes. This fluorescence is rapidly restored in the presence of biological thiols, however, due to their fast addition to this functional group.⁴⁰ Therefore, we suggested that functionalization of the free phenol of this sensor using a benzyl boronic ester should further block the fluorescence, whilst serving as reporter unit for ONOO⁻. The greatly increased reactivity of peroxynitrite over other ROS towards boronate esters^41–43 should allow this functionality to act as a peroxynitrite-selective reporter, leading to an ‘AND’ logic based probe for the detection of ONOO⁻ and biological thiols (Fig. 1, Scheme 1). ROS-AHC was synthesized in 5 steps, starting with a 4-step synthesis of compound 1 adapted from literature procedures,^40,44 followed by the addition of the benzyl boronic pinacol ester (see Scheme S1 ESI^†).Open in a separate windowScheme 1Fluorescence ‘turn on’ mechanism of ROS-AHC in the presence of ONOO⁻ and GSH.The UV-Vis behaviour of ROS-AHC before and after exposure to both GSH and ONOO⁻ was evaluated in pH 7.40 buffer solution, showing a maximum absorption peak at 340 nm for both the unreacted probe and the probe following exposure to GSH, shifting to 350 nm with the addition of ONOO⁻ to the probe and 365 nm after sequential additions of GSH and ONOO⁻ to the probe (Fig. S1 ESI^†). Fluorescence experiments were then carried out. As expected, ROS-AHC was initially non-fluorescent, with a small fluorescence increase upon addition of ONOO⁻ (6 µM) (Fig. 2 and S2 ESI^†). Incremental additions of GSH (0–4.5 µM) resulted in a much larger increase in fluorescence intensity (>69-fold, see Fig. 2 and S3 ESI^†), demonstrating the need for both GSH and ONOO⁻ in order to achieve a significant ‘turn on’ fluorescence response.Open in a separate windowFig. 2Fluorescence spectra of ROS-AHC (5 µM) with addition of ONOO⁻ (6 µM), wait 5 min then incremental addition of GSH (0–4.5 µM), 5 min incubation before measurements in PBS buffer solution (10 mM, pH = 7.40). Fluorescence intensities were measured with λ_ex = 400 nm (bandwidth 8 nm). The green line represents the highest intensity after addition of GSH (4 µM).Similar fluorescence experiments were then carried out in reverse order, with the addition of GSH (6 µM) to ROS-AHC resulting in only a small increase in fluorescence intensity (Fig. 3 and S4 ESI^†). As before, incremental addition of the second analyte, in this case ONOO⁻ (0–5.5 µM), resulted in a large increase in fluorescence intensity (>46-fold, Fig. 3 and S5 ESI^†), confirming that ROS-AHC requires both GSH and ONOO⁻ for a full fluorescence ‘turn on’ response.Open in a separate windowFig. 3Fluorescence spectra of ROS-AHC (5 µM) with addition of GSH (6 µM), wait 5 min then incremental addition of ONOO⁻ (0–5.5 µM) with 5 min incubation before measurements in PBS buffer solution (10 mM, pH = 7.40). Fluorescence intensities were measured with λ_ex = 400 nm (bandwidth 8 nm). The orange line shows the highest intensity after addition of ONOO⁻ (5 µM).Subsequently, the selectivity of this probe towards both analytes was evaluated. A range of amino acids were evaluated (Fig. S6 ESI^†), with only thiol-containing analytes (glutathione, cysteine and homocysteine) eliciting significant fluorescence response, whilst non-thiol amino acids led to no changes in fluorescence intensity. A broad screen of ROS analytes was also carried out, demonstrating excellent selectivity for ONOO⁻, even over H₂O₂ (Fig. S7 ESI^†).The time-dependent response of ROS-AHC with both ONOO⁻ and GSH was also examined (Fig. S8 and S9 ESI^†). After initial addition of GSH or ONOO⁻ to the probe, subsequent addition of the second analyte triggered a rapid and significant increase in fluorescence, achieving maximum fluorescence intensity within 78 s in both cases. Furthermore, LC-MS experiments confirmed the formation of the suggested non-fluorescent intermediates, as well as the final fluorescent species shown in Scheme 1 (Fig S10, S11 and S12^†).In summary, we have developed a coumarin-based dual-analyte ‘AND’ logic fluorescent sensor, ROS-AHC, for the simultaneous detection of ONOO⁻ and biological thiols. ROS-AHC has shown high sensitivity and selectivity towards both ONOO⁻ and biological thiols.     

Green synthesis of crystalline bismuth nanoparticles using lemon juice

Lemon juice effectively served as a reducing and capping agent for an easy, cost-effective, and green synthesis of crystalline bismuth nanoparticles (BiNPs) in basic aqueous media. Spherical BiNPs with a rhombohedral crystalline structure are capped by phytochemicals and stably dispersible in aqueous media. The BiNPs effectively catalyze the reduction of 4-nitrophenol to 4-aminophenol by NaBH₄.

Lemon juice effectively served as a reducing and capping agent for an easy, cost-effective, and green synthesis of crystalline bismuth nanoparticles (BiNPs) in basic aqueous media.

Nanostructures of bismuth, the heaviest element among the ‘safe ones’ earning the status of a ‘green element’,¹ are particularly interesting due to their large magnetoresistance and excellent thermoelectric properties.^2–4 Bismuth nanoparticles (BiNPs) are the most extensively used nanostructures of bismuth. For example, BiNPs are utilized as contrast agents for computed tomography, photoacoustic imaging and infrared thermal imaging,^5,6 catalysts for the reduction of nitroaromatic compounds,^7,8 and removal of NO from air.⁹ Furthermore, BiNPs can act as intermediates for the synthesis of other nanostructures of bismuth, such as thermoelectric Bi₂Te₃ (ref. 10) and seeds for the solution–liquid–solid growth of nanowires.^11,12 Techniques for the synthesis of pure BiNPs could be categorized into (i) thermal decomposition,¹² (ii) mechanochemical processing,¹³ (iii) photochemical reduction,¹⁴ and (iv) solution-phase chemical reduction methods.^6,15–19 The thermal decomposition method requires harsh preparation conditions, expensive organometallic precursors, high temperature, and long reaction time, while producing high-quality monodispersed BiNPs. The mechanochemical processing technique is advantageous in terms of using inexpensive and nontoxic bulk bismuth pellets as precursors. However, the energy consumption and costly instrumentations are the limitations. The photochemical reactions typically require long time for sufficient conversion to bismuth nanoparticles, while they can also produce highly monodispersed BiNPs. The solution-phase chemical reduction methods are most popular due to the facile procedures and accessible reagents. However, stabilizers and toxic reducing agents often used are the limitations. To resolve the above-mentioned limitations, simple and green alternative methods are highly demanded.The use of abundant plant sources, which has been applied for synthesis of various metal nanoparticles such as Ag and Au, is a promising solution.^20,21 Plant sources contain a wide variety of biomolecules potentially serving as reducing and capping agents. Edible plant sources are obviously safest. To the best of our knowledge, there is no report on the synthesis of crystalline BiNPs using plant sources, while P. Poltronieri et al. reported synthesis of amorphous BiNPs using hydroalcoholic extract of Moringa oleifera.²² We focused on lemon, a very common fruit containing abundant antioxidants such as polyphenols, limonoids, citric acid, ascorbic acid, and vitamins potentially reduce ions with high oxidation states. Some of the phytochemicals, namely carbohydrates and proteins bearing ionic moieties, can be capping agents. Accordingly, lemon juice was successfully applied for the formation and in situ stabilization of silver and gold nanoparticles in aqueous media.^23,24 We presumed that a similar mechanism also works for BiNPs.In this communication, we introduce a greener strategy for the synthesis of crystalline BiNPs using lemon juice as a reducing and capping agent. For example, the synthesis was carried out using Bi(NO₃)₃·5H₂O (0.25 mmol) and freshly prepared lemon juice (25 mL) at 80 °C for 2 h under an aerobic basic condition. The X-ray diffraction (XRD) pattern (Fig. 1) of the obtained product was indexed to the pure rhombohedral phase of elemental bismuth (JCPDS no. 44-1246), indicating that the obtained product is BiNPs without detectable oxide phases. The average crystallite size was calculated to be 20 nm applying the Scherrer''s equation on the peaks of the (012), (104) and (110) plane. This result indicates that the phytochemicals present in lemon juice have ability to reduce bismuth salts to form BiNPs. The plausible phytochemicals for reduction are ascorbic acid, citric acid, and sugars. The reduction of Bi³⁺ with glucose⁸ and ascorbic acid¹⁷ was reported, and we accordingly performed the control experiment using possible reducing agents contained in lemon juice, namely ascorbic acid, glucose, and starch without any stabilizing agents. All of them could form elemental bismuth in highly aggregated forms as confirmed by the XRD patterns (ESI, Fig. S9^†) and SEM images (ESI, Fig. S10^†).Open in a separate windowFig. 1XRD pattern of obtained BiNPs synthesized using lemon juice with that of authentic Bi (JCPDS no. 44-1246).Electron microscopy was employed to confirm the size and the morphology of synthesized BiNPs. The scanning electron micrography (SEM) image (Fig. 2a) shows spherical objects having the size in the range of 50 to 100 nm agglomerated and covered with amorphous substances presumably originating from lemon juice. This agglomeration occurred during drying as confirmed by the stable water dispersibility of BiNPs with an average hydrodynamic diameter (D_h) of 255 nm investigated by dynamic light scattering (DLS) (ESI, Fig. S1a^†). The high colloidal dispersibility of the BiNPs and the coating layer observed in the SEM image suggest that phytochemicals present in lemon juice act also as capping agents. The larger D_h measured by DLS than the size observed by SEM can be attributed to the surrounding hydration layer and swelled phytochemicals attached to the surface of the BiNPs. We then performed transmission electron microscopy (TEM) analysis to get the actual size of the Bi cores. The TEM images of the BiNPs (Fig. 2b and c) indicated the presence of heavy elements in the matrix of light elements. The particles are spherical, and the diameter ranges from 8 to 30 nm. The high-resolution TEM image (Fig. 2d) shows the lattice fringes of 0.298 nm, 0.253 nm, and 0.224 nm of the typical crystallite agreeing well with the distance of the (012), (104) and (110) plane, respectively, of the rhombohedral Bi(0).Open in a separate windowFig. 2(a) SEM and (b–d) TEM images of BiNPs synthesized using lemon juice.The EDX spectrum (ESI, Fig. S2^†) reveals that obtained BiNPs comprise bismuth (Bi), carbon (C), and oxygen (O). The strongest signal of bismuth testifies the successful synthesis of BiNPs, whereas the C and O signals demonstrate the presence of the capping layer on the BiNPs.The FT-IR spectrum of the synthesized BiNPs was analyzed to presume the possible components on the BiNPs surface with the comparison with the solid content of lemon juice (Fig. 3). The FT-IR spectrum of the BiNPs shows the following major absorption bands. The broad absorption band at 3050–3500 cm⁻¹ is assignable to the O–H stretching of alcohol moieties. The absorption band around 2840–2940 cm⁻¹ is assignable to the C–H stretching of alkane, and the absence of the sharp absorption around 2950–3050 cm⁻¹ suggests the absence of trace contents of unsaturated C–H groups. The absence of the adsorptions originating from COO–H around 2400–3100 cm⁻¹ and C O around 1700–1730 cm⁻¹ indicates that citric acid^25,26 and other carboxylic acids contained sufficiently in lemon juice are not the major components on the BiNPs, while the presence of the strong absorption around 1600 cm⁻¹ is assignable to carboxylate moieties. The absorption bands around 930–1130 cm⁻¹ assignable to C–C and C–O stretching and around 1200–1420 cm⁻¹ assignable to O–C–H, C–C–H and C–O–H bending suggest the presence of sugars on BiNPs.^25,26 The content of the organic moieties was estimated approximately 14% by thermogravimetric analysis from weight loss that occurred at the temperature range from 130 to 450 °C (ESI, Fig. S3^†), at which the negligible C and O signals were observed in the EDX spectrum of the residue after TGA (ESI, Fig. S2^†).Open in a separate windowFig. 3FT-IR spectra of solid content of lemon juice and obtained BiNPs synthesized using lemon juice.The ¹H and ¹³C NMR and FTIR spectroscopic analysis (ESI, Fig. S4–S8^†) of the ethanol and chloroform extracts of the BiNPs suggests that the major capping phytochemicals are polysaccharides and fatty acid derivatives. Other minor possible components may include amino acids, terpenes and phenolic compounds contained in lemon juice.The successful formation of BiNPs made us enthusiastic to investigate their catalytic performance in the reduction of nitroaromatic compounds, problematic pollutants arising from explosives, analgesic, and antipyretic drugs and dyes.²⁷ Herein, the catalytic performance of our BiNPs was investigated by selecting the reduction of 4-nitrophenol (4-NP) to 4-aminophenol (4-AP) by NaBH₄ at room temperature as a model reaction.^7,8,28 The progress of the reduction was monitored by UV-vis absorption spectroscopy. The colour of the 4-NP aqueous solution changed from light yellow to deep yellow upon the addition of NaBH₄ to produce 4-nitrophenolate ion and an intense absorption peak at 403 nm appeared instead of the original absorption peak of 4-NP at 316 nm in the UV-vis spectrum.⁷ In the absence of BiNPs, the colour of the solution and the intensity of the peak were retained even after 12 h. In the presence of BiNPs, the deep yellow mixture became almost colourless within 180 min (Fig. 4a). The intensity of the absorption peak at 403 nm decreased overtime, and simultaneously a new absorption peak appeared and grew at 299 nm, indicating the formation of 4-AP (Fig. 4a).^8,27,29 The reaction rate almost follows pseudo-first-order kinetics agreeing with the Langmuir–Hinshelwood mechanism; in which two reactants react after adsorption on the solid surface, and then the product desorbs. The rate constant (k) was determined from the plot of ln(A/A₀) vs. time (Fig. 4b) according to the previous reports.^7,8,28,29 The k value of 0.0134 min⁻¹ (activity factor = 0.1 s⁻¹ g⁻¹) is lower than previously reported PVP-coated bismuth nanodots (6.033 s⁻¹ g⁻¹)⁸ and starch coated BiNPs (0.02751 s⁻¹).⁷ The lower catalytic rate of our BiNPs can be attributed to the electrostatic repulsion of 4-nitrophenolate ions with negatively charged BiNPs (zeta potential value = −31.7 mV) in the reaction mixture. The initial rate is slower than the rate after 50 min. Possible factors are (i) the inductive period for the surface activation of the nanoparticles at the initial stage as reported for bismuth nanodots by Liang et al.⁸ and (ii) partial and gradual release of phytochemicals under the basic conditions. After the catalytic reaction, the D_h value measured by DLS (195 nm) became smaller than the original one maintaining the good water dispersibility, suggesting unravelling of primary particles fused by the capping layer (ESI, Fig. S1b^†). In addition, the weight loss in the TGA curve became lower (ESI, Fig. S3^†), and the SEM image implies the partial loss of the coating (ESI, Fig. S11^†). This decrease of the organic moieties is attributable to the partial removal of coating substances such as fatty acids during the catalytic reaction under the basic and reductive conditions, supported by the disappearance of the absorption band around 1600 cm⁻¹ assignable to carboxylate moieties in the FTIR spectrum of BiNPs after the catalytic reaction (ESI, Fig. S12^†). Carboxylic acids and their esters are reported to be reduced to alcohol by NaBH₄ in the presence of electrophiles.^30–33 The initial presence of the amphiphilic and anionic layer plausibly delays the catalytic reaction.Open in a separate windowFig. 4(a) Optical images and absorption spectra of catalytic reduction of 4-NP ([4-NP] = 15 ppm) by NaBH₄ (4.28 × 10⁻⁴ M) in presence of BiNPs (142 mg L⁻¹); (b) pseudo-first order kinetic plot of catalytic reduction.In conclusion, we have demonstrated a green, cost-effective, and successful approach for synthesis of crystalline BiNPs using lemon juice as a reducing as well as capping agent. The obtained BiNPs effectively catalysed the reduction of 4-NP to 4-AP by NaBH₄. The importance of this method lies in the simple synthetic procedure, uses of safe and low-cost lemon, and good dispersibility over conventional chemical approaches.     

Effect of nanostructured silicon on surface enhanced Raman scattering

Non-metallic materials are often employed in SERS systems by forming composite structures with SERS-active metal materials. However, the role of the non-metallic structures in these composites and the effect of them on the SERS enhancement are still unclear. Herein, we studied the effect of silicon morphology on SERS enhancement on silver nanoparticles-coated different structured silicon surfaces. Our finding will help to further understand the SERS mechanism and pave the way for making more efficient SERS systems.

The surface morphology of non-metallic silicon has a big effect on the SERS enhancement of silver nanoparticle-coated silicon surfaces.

In past decades, increasing attention has been attracted to surface enhanced Raman scattering (SERS) due to the dramatically enhanced detection sensitivity of Raman scattering (down to single-molecule sensitivity). The Raman intensity of the molecules located in the vicinity of SERS nanostructures can be enhanced up to 10¹⁰ to 10¹¹ times,^1,2 largely extending the application of SERS in the fields of physics, chemistry and biology, etc.^3–9 Metal materials are mainly employed in fabricating SERS structures, especially gold or silver ones for visible spectrum excitation.^10,11 To date, many nanostructures have been reported that can enhance Raman scattering enormously, leading to so called Raman hot spots,^12–15 including nanogaps,^16,17 nanostars,¹⁸ nanotriangles and nanorods,¹⁹ mainly due to the introduction of a localized electromagnetic field under illumination. This kind of enhancement is referred to as the electromagnetic mechanism, which dominates the SERS enhancement in most cases.Non-metallic structures can also contribute to Raman enhancement, although the enhancement factor is usually very low. It has been reported that Cu₂O,²⁰ TiO₂ ²¹ and ZnS²² nanoparticles can enhance the Raman intensity of adsorbed molecules. Graphene has also been proved to be an efficient platform for Raman enhancement.²³ Although non-metallic materials can be used directly for SERS applications, they are usually used by forming a composite with SERS-active metal material, where they act as supporting materials or borrow the SERS activity from the metallic Raman hot spots. It has been reported that SERS activity can be borrowed from SERS-active materials through ultrathin SERS-inactive transition metals (e.g., Pt, Ni, Co and Pd)²⁴ or dielectric (e.g., SiO₂, Al₂O₃)²⁵ layer. Tian et al. reported the shell-isolated nanoparticle-enhanced Raman spectroscopy (SHINERS) by using the gold nanoparticles coated with ultra-thin silica or aluminum oxide shell.^26,27 Raman enhancement can be achieved at the silica shell surface by borrowing the SERS activity from the gold core. However, the role of non-metallic structures in enhancing Raman scattering and the interactions between these two kinds of materials are still fuzzy.Silicon nanostructures fabricated by catalytic etching method can be easily metalized with silver or gold by electroless deposition for SERS applications.^28–32 However, up to now, only limited types of silicon nanostructures have been reported for SERS applications.^17,30,31 In addition, the role of the nanostructured silicon surface in Raman enhancement is still unclear.In this report, we fabricated SERS structures on two types of silicon surfaces, flat silicon and nanoporous silicon, by metallizing the silicon structure with silver nanoparticles (AgNPs). Compared to the fabricated SERS structure on flat silicon surface, the one fabricated on nanoporous silicon surface showed obvious enhancement on the Raman spectrum of adsorbed probe molecules. The effect of pore size and depth of nanoporous silicon on Raman enhancement was investigated in detail.To investigate the role of silicon nanostructures in Raman enhancement, we compared the Raman spectra of probe molecules adsorbed on AgNPs-coated flat silicon and nanoporous silicon surfaces, respectively. The nanoporous silicon was fabricated by following a modified reported procedure (see details described in Experimental section and scheme shown in Fig. S1 in (ESI^†)).²⁸ Vertical nanopores were produced on silicon surface, and the pore size and pore depth can be easily tuned by varying the reaction parameters. Then a flat silicon and a nanoporous silicon substrates were both metallized with silver by immersing them into a mixed aqueous solution of AgNO₃ and HF,^29,33 forming AgNPs with size of 60 ± 30 nm. The as-prepared AgNPs-coated silicon surfaces (see scanning electron microscopy (SEM) images shown in Fig. S2 in ESI^†) served as SERS-active substrates. After p-aminothiophenol (PATP) molecules (Raman probe) were adsorbed on the AgNPs-coated silicon structures, both AgNPs-coated substrates showed uniform and strong Raman enhancements (Fig. 1). On AgNPs-coated nanoporous silicon surface, the Raman bands of PATP molecules at 1076 and 1142 cm⁻¹ are 4.2 and 7.4 times stronger compared to those on AgNPs-coated flat silicon surface (Fig. 1), respectively, demonstrating the vital role of silicon morphology in the obtained Raman enhancement. There are two widely accepted mechanism for SERS enhancement, electromagnetic mechanism and charge transfer mechanism.¹ Both flat silicon and nanoporous silicon substrates are composed of same material and the only difference between them is the silicon morphology. Thus the charge transfer mechanism should contribute similar effect in both conditions. Moreover, both flat and nanoporous silicon surfaces were covered with a thin layer of silicon dioxide,^28,34 which limit the charge transfer between AgNPs and silicon surface. This is also confirmed by the XPS measurement on the nanoporous silicon surface (Fig. S3 in ESI^†). Therefore, the observed different enhancement may attribute to the electromagnetic mechanism, which will be discussed latter. In addition, the Raman enhancement is uniform over the whole substrate. This is probably due to the uniform coating of AgNPs on high-density silicon nanopore structures. The enhancement factor (EF) can be calculated by using the following equation, EF = (I_SERS/I_bulk)(N_bulk/N_SERS),³⁵ where I_SERS and I_bulk represent the Raman intensities in SERS and bulk Raman measurements, respectively; N_SERS and N_bulk represent the number of probe molecules located in the excitation volume under these two conditions. For Raman band at 1076 cm⁻¹ (represents a₁ vibration mode of PATP,¹¹ which sits at 1089 cm⁻¹ for bulk,³⁶ Fig. S4 in ESI^†), the average EFs over the whole surface were calculated as 6.7 × 10⁵ and 2.8 × 10⁶ for SERS structures on flat silicon and nanoporous silicon, respectively. The strong Raman band at 1142 cm⁻¹ indicates a chemical conversion from PATP to 4,4′-dimercaptoazobenzene (DMAB) upon light irradiation.¹¹Open in a separate windowFig. 1Raman spectra of PATP molecules adsorbed on the AgNPs-coated (a) flat silicon and (b) nanoporous silicon. A nanoporous silicon with pore depth of 220 nm was used here. The schemes at the bottom right and top right show the structures of the AgNPs-coated flat silicon surface and AgNPs-coated nanoporous silicon surface, respectively. The size of AgNPs was not drawn to scale.As discussed, electromagnetic mechanism dominates the observed SERS enhancement. To confirm the role of silicon morphology, we did numerical simulation using the finite-difference time-domain (FDTD) method to investigate the localized electromagnetic field distributions on AgNPs-coated flat and nanoporous silicon surfaces. Note that, for the AgNPs-coated nanoporous silicon surface, many AgNPs sit on the edge of silicon nanopores (Fig. S2D in ESI^†). In this case, the electromagnetic field around the AgNPs is more localized. Compared with the AgNPs-coated flat silicon, the electromagnetic field is five times more localized on the AgNPs-coated nanoporous silicon surface (Fig. 2), which in principal could introduce 25 times stronger Raman enhancement.³⁷ However, in real case, only a proportional of the AgNPs locates on the edge of silicon nanopores and the shapes of the coated AgNPs are not exactly same with the ones we used in simulation, which explains the smaller SERS enhancement we observed on nanoporous silicon surface.Open in a separate windowFig. 2Schemes (side views) and FDTD simulations on the AgNPs-coated flat silicon (A and B) and nanoporous silicon (C and D). Dashed circles in (D) indicate the positions of silicon pores. The schemes in (A) and (C) were not drawn to scale.As discussed above, the morphology of nanoporous silicon contributes to the enhanced Raman signal. By varying the pore size and pore depth of the nanoporous silicon, different Raman enhancement should be observed.First, we studied the effect of pore depth of nanoporous silicon on Raman enhancement. The depth of silicon nanopores can be easily tuned by varying the period of catalytic etching of silicon. The Raman intensity of the probe molecules increased continuously with increased silicon nanopore depth (from 40 to 220 nm, Fig. 3). When PTAP molecules were adsorbed on the AgNPs-coated nanoporous silicon surface, the Raman intensity measured on silicon with 220 nm pore depth was increased about 2 times compared to that on silicon with 40 nm pore depth. Further increasing the pore depth to 900 nm, the Raman intensity dropped instead (Fig. 3). These results indicate the important role of the pore depth in Raman enhancement. FDTD simulations were carried out to investigate the mechanism behind (Fig. S5 in ESI^†). As the pore depth increases, the electromagnetic field becomes more localized, which is consistent with the experimental data. However, the Raman intensity decreased on surface with very deep silicon nanopores (900 nm), which can be explained by the enhanced light trapping.^38,39 In this case, part of the Raman scattering light cannot escape from the nanopores (confirmed by the dark black color of the sample, Fig. S6 in ESI^†), leading to a weaker Raman signal. This can also be double confirmed by studying the Raman scattering from nanoporous silicon samples with AgNPs located at the bottom of the nanopores (discussed in ESI and Fig. S7^†).Open in a separate windowFig. 3Raman intensity variation (peak at 1076 cm⁻¹) on the AgNPs-coated nanoporous silicon (pore size of ∼40 nm was used) surface with four different depths. The scheme on top was not drawn to scale.Second, the size of silicon nanopores also plays a role in the Raman enhancement. The pore size on silicon surface can be tuned by controlling the size of catalysts (AgNPs) deposited on silicon wafer (Fig. S1B in ESI^†), whose size was replicated by the nanopores in subsequent catalytic etching process (Fig. S1C^†). By varying the deposition time, nanoporous silicon samples with four different pores sizes, 31 ± 10, 41 ± 11, 80 ± 24 and 160 ± 50 (Fig. 4A–D), were fabricated, respectively. For the AgNPs-coated nanoporous silicon samples, the Raman intensity of probe molecules slightly changed while increasing the pore size (Fig. 4E), indicating a weak effect of pore size on Raman enhancement. As aforementioned discussion, the Raman enhancement is mainly contributed by the AgNPs that locate on the nanopore edges. Therefore, the Raman enhancement is strongly dependent on the perimeter of all the nanopores and the number of AgNPs that locate on the edge of silicon nanopores. While increasing the pore size, the perimeter of single pore increases. However, many pores are fused together, compensating the increase of the perimeter of single pore. Thus, the total perimeter of all nanopores does not change much when increasing the pore size. In this case, the amount of the AgNPs locating on the edge of silicon nanopores may not change too much, which may explain the less dependency of the pore size on SERS enhancement. To investigate the structure of the AgNPs-coated nanoporous silicon, we deposited gold nanoparticles (AuNPs) onto it. In this case, however, a stronger Raman scattering was observed due to the formation of AgNP–AuNP nanogaps and the enhancement varied on different sized silicon nanopores. When increasing the pore size from 31 ± 10 to 80 ± 24 nm, the Raman scattering became stronger. Further increasing the pore size to 160 ± 50 nm, the Raman intensity decreased. As known, two particles formed nanogap shows a more localized electromagnetic field when the polarization of incident light is parallel to the center to center axis of the two particles.^16,40 Therefore, horizontal positioned two-particle nanogaps will give much stronger Raman enhancement. If the size of the silicon nanopores is too small, it is difficult for the AuNPs (13 nm in diameter) to enter the pore, limiting the number of AgNP–AuNP nanogaps that are horizontally positioned, and in turn limiting the Raman enhancement. While increasing the nanopore size, we have a better chance to form the ideally positioned AgNP–AuNP nanogaps to improve the Raman enhancement (Fig. S8 in ESI^†). However, when the pore size is too big, only a small part of the nanostructures locates inside the excitation volume during Raman measurement, leading to a weaker Raman signal.Open in a separate windowFig. 4(A–D) Nanoporous silicon with different pore sizes obtained by varying the silver deposition time described in Fig. 1A and B. Scale bars = 200 nm. The pore depth here was set as 220 nm. (E) Raman intensity variation (peak at 1076 cm⁻¹) on the AgNPs-coated nanoporous (four different pore sizes shown in A–D) silicon surface without (magenta bars) and with (cyan bars) the adsorption of AuNPs.The Raman enhancement can also be affected by the size of the AgNPs coated on nanoporous silicon. The AgNP size can be tuned by varying the AgNP deposition time shown in Fig. S1E.^† It has been reported that AgNPs with several tens of nanometers showed optimized plasmon resonance with excitation wavelength of 632.8 nm.⁴¹ In this work, the 40–75 nm AgNPs coated on nanoporous silicon show higher Raman enhancement than those with smaller or bigger AgNPs (Fig. S9^†), since the size of these AgNPs fall into the optimized range for Raman enhancement, which is consistent with the reported work.     

A novel fluorescent probe for imaging the process of HOCl oxidation and Cys/Hcy reduction in living cells

A new on-off-on fluorescent probe, CMOS, based on coumarin was developed to detect the process of hypochlorous acid (HOCl) oxidative stress and cysteine/homocysteine (Cys/Hcy) reduction. The probe exhibited a fast response, good sensitivity and selectivity. Moreover, it was applied for monitoring the redox process in living cells.

A new on–off–on fluorescent probe, CMOS, was designed and applied to detect the process of HOCl oxidation and Cys/Hcy reduction.

Reactive oxygen species (ROS) are indispensable products and are closely connected to various physiological processes and diseases.¹ For instance, endogenous hypochlorous acid (HOCl) as one of the most important ROS, which is mainly produced from the reaction of hydrogen peroxide with chloride catalyzed by myeloperoxidase (MPO), is a potent weapon against invading pathogens of the immune system.^2,3 However, excess production of HOCl may also give rise to oxidative damage via oxidizing or chlorinating the biomolecules.⁴ The imbalance of cellular homostasis will cause a serious pathogenic mechanism in numerous diseases, including neurodegenerative disorders,⁵ renal diseases,⁶ cardiovascular disease,⁷ and even cancer.⁸ Fortunately, cells possess an elaborate antioxidant defense system to cope with the oxidative stress.⁹ Therefore, it is necessary and urgent to study the redox process between ROS and antioxidants biosystems.Fluorescence imaging has been regarded as a powerful visual methodology for researching various biological components as its advantages of high sensitivity, good selectivity, little invasiveness and real-time detection.^10,11 To date, amounts of small molecular fluorescent probes have been reported for detection and visualization of HOCl in vivo and in vitro.^12–22,29 The designed strategies of HOCl sensitive probes are based on various HOCl-reactive functional groups, such as p-methoxyphenol,¹³p-alkoxyaniline,¹⁴ dibenzoyl-hydrazine,¹⁵ selenide,¹⁶ thioether,¹⁷ oxime,¹⁸ hydrazide,¹⁹ hydrazone.²⁰ But, many of these probes display a delayed response time and low sensitivity. And, only few fluorescent probes can be applied for investigating the changes of intracellular redox status.²¹ Besides, it''s worth noting that most of the redox fluorescent probes rely on the organoselenium compounds.²² Even though these probes are well applied for detection of cellular redox changes, excessive organic selenium is harmful to organisms and the synthesis of organoselenium compounds is high requirement and costly. Additionally, almost all the reports have only investigated the reduction effects of glutathione (GSH) as an antioxidant in the redox events. While, there are the other two important biothiols, cysteine (Cys) and homocysteine (Hcy), which not only present vital antioxidants, but also are tightly related to a wide variety of pathological effects in biosystem, such as slowed growth, liver damage, skin lesions,²³ cardiovascular,²⁴ and Alzheimer''s diseases.²⁵ However, the fluorescent probes for specially studying internal redox changes between HOCl and Cys/Hcy are rarely reported. In this respect, a novel redox-responsive fluorescent probe, CMOS, was designed and synthesized in this work, and we hope that it can be a potential tool for studying their biological relevance in living cells.Based on literature research, the aldehyde group has excellent selectivity in identification of Cys/Hcy, and the thiol atom in methionine can be easily oxidized to sulfoxide and sulfone by HOCl.^26,27 Considering these two points, we utilized 2-mercaptoethanol to protect the 3-aldehyde of 7-diethylamino-coumarin as the recognition part of HOCl, meaning that two kinds of potential recognition moieties are merged into one site. Fluorescent probe CMOS can be easily synthesized by the acetal reaction in one step (Scheme S1^†). A control molecule CMOS-2 was also prepared by 3-acetyl-7-diethylaminocoumarin (CMAC) similarly. The structure of all these compounds have been convinced by ¹H NMR, ¹³C NMR, and HR-MS (see ESI^†).As shown in Scheme 1a, we estimated that both CMOS and CMOS-2 can be rapidly oxidized in the appearance of HOCl. The oxidation product CMCHO of CMOS, which has the aldehyde moiety, can further react with Cys/Hcy to obtain the final product CMCys and CMHcy, respectively. In contrast, the oxidation product CMAC of CMOS-2 cannot combine with Cys/Hcy or other biothiols anymore (Scheme 1b).Open in a separate windowScheme 1Proposed reaction mechanism of CMOS and CMOS-2 to HOCl and Cys/Hcy.In order to confirm our design concept, the basic photo-physical characteristics of CMOS, CMCHO, CMOS-2 and CMAC were tested (Table S1, Fig. S1^†). Under the excitation wavelength 405 nm, CMOS and CMOS-2 exhibited strong fluorescence centred at 480 nm in PBS buffer solution, while the fluorescence of CMCHO and CMAC was weak around this band. The emission properties of CMOS and CMCHO were also investigated at the excitation wavelength 448 nm under the same experimental conditions as well (Fig. S2^†). After careful consideration, we chose 405 nm as the excitation wavelength in the follow-up experiments in vitro and in vivo.Next, the sensitivity of CMOS and CMOS-2 to HOCl and Cys/Hcy were investigated. As we expected, both the CMOS and CMOS-2 exhibited good response to HOCl. The fluorescence intensity of CMOS and CMOS-2 decreased gradually with addition of NaOCl (Fig. 1a, S3a^†), indicating that the fluorescence was switched off obviously in the presence of HOCl. The variation of intensity displayed good linearity with concentration of HOCl in the range of 0–20 μM (R² = 0.993, Fig. S4^†), and the detection limit of CMOS to HOCl was calculated to be 21 nM (S/N = 3). Subsequently, when Cys/Hcy was added to the final solution in Fig. 1a, the fluorescence intensity increased gradually within 180 min (Fig. 1b, S5^†). However, the fluorescence cannot be recovered by addition thiols to the CMOS-2 solution with excess HOCl (Fig. S3b^†). These results indicate that the probe CMOS can response to HOCl and Cys/Hcy in a fluorescence on-off-on manner, and can be used for monitoring the redox process with high sensitivity.Open in a separate windowFig. 1(a) Fluorescence responses of CMOS (2 μM) to different concentrations of NaOCl (0–200 μM). (b) Fluorescence responses of the CMOS solution (2 μM) with HOCl (200 μM) to Cys/Hcy (5 mM). (20 mM PBS buffer/CH₃CN, 7 : 3, v/v, pH = 7.4, λ_ex = 405 nm).To further identify the recognizing mechanism of probe CMOS, high performance liquid chromatography (HPLC) and mass spectral (MS) analysis were used to detect the redox process. Initially, probe CMOS displayed a single peak with a retention time at 3.7 min (Fig. 2a, S6^†) while reference compound CMCHO produced a single peak with a retention time at 2.5 min (Fig. 2b, S7^†). Upon the addition of HOCl to the solution of CMOS, the peak at 3.7 min weakened while 2.5 min and 2.2 min appeared (Fig. 2c). According to corresponding mass spectra, the new main peak at 2.5 min is related to compound CMCHO (Fig. S8^†). The other new peak of 2.2 min corresponds to the compound C3, which can be predicted as an intermediate in the oxidation process (Fig. S8^†).²⁸ The addition of Cys to the solution of CMCHO also caused a new peak with a retention time at 2.1 min, which has been confirmed to be the thioacetal product CMCys (Fig. S9^†). The possible sensing mechanism is depicted in Fig. S10.^†Open in a separate windowFig. 2The reversed-phase HPLC with absorption (400 nm) detection. (a) 10 μM CMOS. (b) 10 μM CMCHO. (c) 10 μM CMOS in the presence of 50 μM HOCl for 30 s. (d) 10 μM CMCHO in the presence of 1 mM Cys for 30 min. (Eluent: CH₃CN containing 0.5% CH₃COOH; 100% CH₃CN (0–7 min), 0.5 ml min⁻¹, 25 °C; injection volume, 5.0 μL).To study the selectivity of CMOS towards HOCl, we performed fluorescence response to different reactive oxygen species (ROS), reactive nitrogen species (RNS) and reactive sulfur species (RSS). As shown in Fig. 3a, CMOS exhibited significant change of fluorescence intensity only in the presence of HOCl, while other ROS and RNS, such as singlet oxygen (¹O₂), hydrogen peroxide (H₂O₂), hydroxyl radical (HO·), superoxide anion (O₂⁻), nitric oxide (NO), tert-butylhydroperoxide (t-BuOOH) and tert-butoxy radical (t-BuOO·) had no obvious fluorescence emission changes. Additionally, RSS which are abundant in biological samples, showed no influence in this process under the identical condition. The detection of reducing process was also investigated. As displayed in Fig. 3b, only cysteine and homocysteine induced excellent fluorescence recovery towards other reducing materials, such as RSS and various amino acids. Furthermore, the selectivity of CMOS-2 was also studied in the same condition. As expected, CMOS-2 could selectively detect HOCl, and not alter fluorescence intensity under various kinds of biothiols (Fig. S11^†). Therefore, our design strategy for the on–off–on probe is confirmed by results obtained above, with which CMOS can be utilized for detecting the redox process between HOCl and Cys/Hcy with high selectivity.Open in a separate windowFig. 3(a) Fluorescence response of CMOS (2 μM) to different ROS, RNS and RSS (200 μM). Bars represent emission intensity ratios before (F₀) and after (F₁) addition of each analytes. (a) HOCl; (b) KO₂; (c) H₂O₂; (d) ¹O₂; (e) HO·; (f) t-BuOOH; (g) t-BuOO·; (h) NO₂⁻; (i) NO₃⁻; (j) NO; (k) GSH; (l) Cys; (m) Hcy; (n) Na₂S; (o) Na₂S₂O₃; (p) Na₂S₂O₈; (q) NaSCN; (r) DTT; (s) Na₂SO₃. (b) Fluorescence response of the solution added HOCl in (a) to different RSS and amino acids. Bars represent emission intensity ratios before (F₂) and after (F₃) addition of each analytes (5 mM). (a) Cys; (b) Hcy; (c) Na₂S; (d) Na₂S₂O₃; (e) Na₂S₂O₈; (f) NaSCN; (g) DTT; (h) Na₂SO₃; (i) Ala; (j) Glu; (k) Gly; (l) His; (m) Ile; (n) Leu; (o) Met; (p) Phe; (q) Pro; (r) Ser; (s) Trp; (t) Vc; (u) GSH. (20 mM PBS buffer/CH₃CN, 7 : 3, v/v, pH = 7.4, λ_ex/λ_em = 405/480 nm).Subsequently, the influence of pH on probe CMOS was measured. The fluorescence intensity of CMOS and CMCHO perform no significant variances in wide pH ranges (pH = 4–11, Fig. S12a^†). Fluorescence intensity changes could be observed immediately when HOCl was added into the solution of probe CMOS, especially in alkaline condition (Fig. 4a). Considering the pK_a of HOCl is 7.6,²⁹CMOS is responsive to both HOCl and OCl⁻. Alkaline condition was also benefit for the fluorescence recovery of CMOS from Cys/Hcy (Fig. S12b^†). It is reasonable to consider that thiol atom displays higher nucleophilicity in alkaline condition. From the stop-flow test, the UV-visible absorbance of probe CMOS sharply decreased at the wavelength of 400 nm (Fig. 4b). The response time was within 10 s and the kinetic of the reaction was fitted to a single exponential function (k_obs = 0.67 s⁻¹). The ability of instantaneous response is extremely necessary to intracellular HOCl detection.Open in a separate windowFig. 4(a) Fluorescence responses of CMOS to HOCl under different pH values. Squares represent emission intensity ratios after (F₁) and before (F₀) addition of 200 μM HOCl (λ_ex/λ_em = 405/480 nm). (b) Time-dependent changes in the absorption intensity of CMOS (1 μM) before and after addition of HOCl. (20 mM PBS buffer/CH₃CN, 7 : 3, v/v, pH = 7.4, λ_abs = 400 nm).With these data in hand, we next applied CMOS for fluorescence imaging of the redox changes with HOCl and Cys/Hcy in living cells. After incubation with 5 μM CMOS at 37 °C for 30 min, intense fluorescence was observed of the SKVO-3 cells in the optical window 425–525 nm (Fig. 5a and d), indicating the probe can easily penetrate into cells. Treating the cells with 100 μM NaOCl led to remarkable fluorescence quenching as the probe sensed the HOCl-induced oxidative stress (Fig. 5b and e). After 3 min, the cells were washed with PBS buffer three times, and added 5 mM Cys/Hcy for 1 h, respectively. Then the fluorescence was recovered obviously (Fig. 5c and f). Experimental results clearly declare that the probe CMOS was successfully used to detect the process of HOCl oxidative stress and Cys/Hcy reducing repair in living cells.Open in a separate windowFig. 5Fluorescence imaging of the process of HOCl oxidative stress and thiols repair in CMOS-labeled SKVO-3 cells. Fluorescence images of SKVO-3 cells loaded with 5 μM CMOS at 37 °C for 30 min (a and d). Dye-loaded cells treated with 100 μM NaOCl at 25 °C for 3 min (b and e). Dye-loaded, NaOCl-treated cell incubated with 5 mM Cys (c), 5 mM Hcy (f) for 1 h. Emission intensities were collected in an optical window 425–525 nm, λ_ex = 405 nm, intensity bar: 0–3900.     

Thermally induced fragmentation of nanoscale calcite

Calcite nanorods ∼50 nm wide are thermally separated into nanoblocks. The fragmentation is ascribed to the ion diffusion on metastable crystal surfaces at temperatures (∼400 °C) much lower than the melting point. The presence of water molecules enhances the surface diffusion and induces deformation of the nanorods even at ∼60 °C.

Calcite nanorods ∼50 nm wide are thermally separated into nanoblocks.

Calcium carbonate is a common industrial material that is used as a micrometric filler for papers, rubbers, plastics, and inks. The shape and size of micrometric grains are important parameters that affect the physical and chemical properties of composite materials.^1–5 In recent years, nanometric particles of calcium carbonate have attracted much attention as basal building blocks of biogenic minerals^6–10 and functional materials with high biocompatibility and low environmental load.^11–14 Since various properties are influenced by the miniaturization of crystal grains below 100 nm, characterization of the carbonate particles is necessary for application in practical fields. However, their properties, including the thermal characteristics of nanometric calcium carbonate in the nanometric region, have not been sufficiently clarified because calcium carbonate is easily decomposed above 550 °C.^15,16 In the present work, we studied thermally induced deformation on nanometric calcite at temperatures lower than the melting point (1597 °C at 3 GPa)¹⁷ of the bulky crystal.Since the melting temperature of metals decreases when their size is decreased below ∼50 nm,^18,19 metallic nanowires fragment into nanospheres at temperatures much below the melting point of bulk metal.^20–22 The fragmentation is ascribed to the Rayleigh instability that is known for liquid. These results suggest that the surface diffusion of ions and atoms occurs easily on the nanometric particles when the surface instability is increased. The cleavage of solid nanowires has been observed only for metallic phases. In the current work, we found the morphological transformation of ion crystal nanorods into faceted nanograins through the surface diffusion at relatively low temperatures.The preparation of bulky calcium carbonate consisting of nanocrystals is required for reinforcing materials^23–25 and as a precursor of biomedical materials.^26,27 In general, however, fabricating large, bulky bodies through conventional sintering techniques is difficult because calcium carbonate is thermally decomposed into calcium oxide and carbon dioxide. Several methods, such as sintering with a flux^16,28 or in a carbon dioxide atmosphere²⁹ and hot-pressing under hydrothermal conditions^30,31 were developed to prepare bulky calcium carbonate materials. On the other hand, the thermal behaviors of pure calcium carbonate have not been sufficiently studied at temperatures below the decomposition and melting points.In nature, bulky calcium carbonate crystals are commonly produced as biominerals, such as shells, eggshells, sea urchins, and foraminiferal skeletons, under mild conditions.^{3,9,10,32–34} The bulky biogenic bodies are composed of nanometric grains 10–100 nm in size that are arranged in the same crystallographic direction.³ The formation of bridged architectures through oriented attachment is generally related to the ion diffusion on specific surfaces at relatively low temperatures. A detailed study on the stability of nanometric surfaces at relatively low temperatures is needed to understand the morphological change of calcium carbonate crystals.In the present report, we discuss the morphological change of calcite nanocrystals below the decomposition and melting temperatures by observing metastable crystal surfaces in the nanometer-scale range. Calcite nanorods elongated in the c direction were utilized as a typical nanometric shape covered with metastable surfaces. Here, thermally induced fragmentation was studied with and without water vapor. The surface diffusion was found to occur on the metastable surface at around 400 °C under a dry condition and at around 60 °C with water vapor. Our findings are important for clarification of the surface property of nanometric calcium carbonate and for the fabrication of bulky bodies through the attachment of nanocrystals.Single-crystal calcite nanorods elongated in the c direction were utilized in the present study (Fig. 1 and S1^†). Calcite nanorods up to ∼500 nm were formed through the combination of the carbonation of calcium hydroxide and the subsequent oriented attachment of resultant calcite nanoblocks ∼50 nm in diameter by stirring. The detailed mechanism was described in our previous study.³⁵ As shown in Fig. S1,^† the calcite nanorods were covered with metastable surfaces having a curvature. Moreover, we observed depressed parts originating from the oriented attachment of the original calcite grains. As shown in the Fig. S2,^† the XRD peaks of the nanorods were found to shift to higher angles than those of standard X-ray diffraction data (ICDD 00-005-0586). Thus, the crystal lattice of the nanorods was suggested to be stressed with the coverage of irregular surfaces.Open in a separate windowFig. 1SEM (a) and TEM (b and c₁), HRTEM (c₂) images, and the FFT pattern (c₃) of the lattice in (c₂) of calcite nanorods in aqueous dispersions at pH 12 and at 25 °C with stirring. (c) Reprinted from ref. 35 published by The Royal Society of Chemistry.As shown in Fig. 2, the calcite nanorods were deposited on a silicon substrate for clear observation of the morphological change. We redispersed the calcite nanorods in ethanol and evaporated the dispersion medium to deposit them on the substrate at 25 °C (Fig. 2a and S3a^†).³⁶ The nanorods were arranged on the solid surface through evaporation-driven self-assembly. Specifically, monolayers of the calcite nanorods were obtained by adding poly(acrylic acid) (PAA, MW: 5000 gmol⁻¹) to the ethanol dispersion. The dispersibility of the nanorods in ethanol was improved by the modifying agent. The organic components of the PAA-modified nanorods were removed through oxidation in air at around 300 °C (Fig. S4^†).Open in a separate windowFig. 2SEM images and schematic illustrations of calcite nanorods deposited on a silicon substrate before treatment (a) and heated at 400 °C for 1 (b) and 2 h (c). The PAA-modified calcite nanorods were used to obtain the monolayers (b and c). We used bare nanorods for take the images of original nanorods because the definite surfaces were not observed due to the presence of PAA (a).The calcite nanorods were deposited on the solid surface to study the morphological change when heated in air. Obvious changes were not found in the shape of the nanorods upon heating to a temperature below 350 °C in air for 24 h (Fig. S2^†). On the other hand, we observed significant deformation upon heating to 400 °C (Fig. 2). The depressed parts on the side surfaces enlarged in 1 h. The fragmentation of the nanorods was finally induced after treatment for 2 h. Calcite grains were formed by the thermally induced cleavage (Fig. 2c). The average size of the cleaved grains was ∼100 nm, which was larger than the average width of the nanorods, ∼50 nm. As shown in Fig. 3, we observed the definite surfaces covering nanograins. Most of the definite facets were assigned to the (104) of calcite by FFT analysis of the lattice fringes of nanograins in the HRTEM images. Some (012) planes were found in the nanograins. On the other hand, the surfaces of the deformed nanorods during fragmentation were curved and irregular. According to XRD patterns, the crystal phase was not changed with the fragmentation (Fig. S2^†). The diffraction peaks were shifted to the standard values and sharpened with the treatments. This suggests that the formation of the stable faces with the fragmentation is associated with the lattice relaxation.Open in a separate windowFig. 3TEM (a), HRTEM (b), and FFT images of nanocrystals before and after heating at 500 °C.We observed the stability of rhombohedral grains that were covered with the stable {104} planes. As shown in Fig. 4, the deformation of the rhombohedral grains was not observed at 400 °C in air for 6 h. These results indicate that the ion diffusion is not induced drastically on the stable surfaces at a temperature lower than the decomposition temperature.Open in a separate windowFig. 4SEM (a_1,2 and b_1,2), TEM (a₃), and SAED (a₄) images of calcite nanoblocks before treatment (a) and heated to 400 °C for 6 h (b). (a₃) A schematic illustration of a calcite rhombohedron covered with {104} faces.The fragmentation of the calcite nanorods was enhanced in the presence of water vapor. As shown in Fig. 5a, we found cleavage of the nanorods even at 60 °C in a closed vessel containing water. The formation of unifaceted rhombohedral nanoblocks with {104} faces was clearly observed at 100 °C for 24 h (Fig. 5b–d). Since the morphological change was similar to that under a dry condition, the ion diffusion on the surface is deduced to be assisted by adsorbed water molecules. The X-ray diffraction signals shifted to the standard values with the fragmentation (Fig. S2^†). Thus, the stable faces were formed with the lattice relaxation with the exposure to water vapor.Open in a separate windowFig. 5SEM (a and b), TEM (c), and SAED (d) images of calcite nanorods deposited on a silicon substrate subjected to high humidity at 60 °C (a) and 100 °C (b) for 24 h. (c) A schematic illustration of a calcite rhombohedron covered with {104} faces.The ion diffusion at a relatively low temperature, below the decomposition temperature, has not been reported for calcium carbonate. In the present work, however, we found the fragmentation of calcite nanorods at around 400 °C under a dry condition and at around 60 °C with water molecules. These results suggest that the ion diffusion occurs on the nanoscale calcite crystals. On the other hand, rhombohedral calcite grains covered with the stable {104} planes were not deformed at those temperatures. Thus, the diffusion at low temperatures is induced only on metastable surfaces that are exhibited on the nanoscale calcite. Moreover, the presence of water molecules enhances the ion diffusion on the metastable surfaces.The fragmentation of the calcite nanorods can be explained by Rayleigh instability. The cleavage by Rayleigh instability is ascribed to the enlargement of tiny perturbations on cylindrical liquids,³⁷ polymers, and metals. In general, the cylindrical bodies evolve into several spheres to decrease the total surface energy. Recently, Rayleigh instability was applied to the thermally induced fragmentation of metal^20–22 and organic³⁸ nanowires. The breakup phenomena were attributed to surface oscillations due to the high surface energy induced by increased surface-to-volume ratios.³⁹ Thus, metal nanowires are cleaved and form isotropic nanoblocks at temperatures well below the melting point. In the present work, we found fragmentation of the calcite nanorods at relatively low temperatures. The ion diffusion is induced on the metastable surfaces that are exhibited on nanoscale crystals. The depressed parts exist as perturbations on the side faces of the original nanorods. The cleavage occurs through enlargement of the depressed parts and formation of the stable faces to reduce the surface energy and relax the lattice strain.Polyhedral grains covered with flat planes were formed instead of spherical particles by the fragmentation of calcite nanorods. Formation of the stable {104} plane is achieved to reduce the surface energy. The {012} plane of calcite is not stable under the ambient temperature. However, the surface energy of {012} decreases with increasing temperature.⁴⁰ Thus, the facets are deduced to also be formed at temperatures around 400 °C.     

Separating graphene quantum dots by lateral size through gel column chromatography

Graphene quantum dots (GQDs) prepared through photo-Fenton reaction of graphene oxide are separated via gel column chromatography. The as-separated GQDs were selectively introduced into the active layer of organic solar cells and achieved an enhancement of power conversion efficiency (PCE).

GQDs prepared through a photo-Fenton reaction were separated into eight groups with different sizes and fluorescent colors via gel column chromatography.

Graphene quantum dots (GQDs) show potential applications in photovoltaic devices, bio-probers, sensors, and catalysts.^1–6 As the properties of GQDs can be affected severely by their lateral sizes and size distributions,^7,8 to acquire GQDs with controlled size and narrow distribution is prerequisite. However, GQDs prepared directly by the methods developed so far usually assume wide size distribution which limits somehow the practical applications of GQDs.^2,9–12Recently, several protocols have been developed for post separation of GQDs, such as dialysis,¹³ ultrafiltration,¹⁴ gel electrophoresis,⁸ reverse micelle methods,¹⁵ column chromatography on silica¹⁶ or Sephadex G-25 gel,¹⁷ chromatographic separation,¹⁸ and size-selective precipitation,^19,20 but can''t satisfy the bulk production. For examples, Kim et al. successfully obtained GQDs with different sizes using dialysis bags with different interception molecular weights and a 20 nm nanoporous membrane, but with an unacceptable yield.¹³ Fuyuno et al. obtained the GQDs with different fluorescence by the size-exclusion high performance liquid chromatography (HPLC).¹⁸ Jiang et al. separated the single atomic layered GQDs from reaction mixture containing double multilayer allotropes successfully through a Sephadex G-25 gel.¹⁷ In our previous work, the GQDs generated through the photo-Fenton reaction of graphene oxide (GO) have been sorted into three categories with different fluorescence by gel electrophoresis.^2,8,20 Nevertheless, it is still challenging to obtain high quality GQDs with controlled size and size distribution which can satisfy the practical applications.Herein, we describe an efficient GQDs separation procedure via Sephadex G25 gel column. The GQDs prepared through photo-Fenton reaction of GO with wide size distribution are separated into eight groups of GQDs with different size and fluorescent colours.² The size and morphology of as-obtained GQDs were characterized by atomic force microscopy (AFM) and transmission electron microscopes (TEM) measurements. The optoelectronic properties of the GQDs were studied by photoluminescence (PL) and UV-vis absorption spectroscopy techniques. The results showed that this separating technique is very beneficial for obtaining high quality GQDs with a variety of specific sizes and properties. Finally, the as-separated GQDs were introduced into the inverted hybrid solar cells based on the poly(3-hexylthiophene) (P3HT) and poly(3-hexylthiophene)/(6,6)-phenyl-C61 butyric acid methylester (PCBM), and it is found that the solar cell containing the separated GQDs showed a higher performance than that with the raw GQDs, which verified the importance of the size separation for GQDs.The raw GQDs used in the work are first characterized using atomic force microscopy imaging. As shown in Fig. S1a and b,^† their sizes are ranged from 2 to 40 nm with obviously large size distribution, that is further confirmed by PL spectrum and image (Fig. S1c,^† and the inset). Sephadex G25 gel column, one of common size exclusion column, is widely used to purify or separate protein or peptide.²¹ Here, GQDs are separated through Sephadex G25 gel column by size and the as-separated GQDs are named as GQDs 1–8 according to the collection order. The yield of GQDs is close to 80% with this separating technique. Actually, unlike other separating methods such as multiple dialysis¹³ and ultrafiltration,¹⁴ there is almost no significant loss of GQDs in our separation process. Taking the well dispersibility of as-prepared GQDs in water into consideration, we selected water as developing solvent in this work. Their morphologies, size and size distributions are revealed by AFM imaging and the results are shown in Fig. 1. The average size of GQDs 1–8 (calibrated with the parameters of AFM tip deconvolution⁸) are of 27.5, 23.5, 15.5, 12.0, 8.5, 6.3, 5.2 and 3.0 nm, respectively, with narrow size distributions (see the as-inset histograms in Fig. 1). As shown in Fig. S2,^† the sizes of GQDs 1–8 are also measured by TEM imaging, which are in agreement with the AFM images.Open in a separate windowFig. 1Tapping mode AFM images (height) of the separated GQDs samples along the collecting order (a) GQDs 1, (b) GQDs 2, (c) GQDs 3, (d) GQDs 4, (e) GQDs 5, (f) GQDs 6, (g) GQDs 7, (h) GQDs 8. The insets are the histograms of the size.The PL and UV-vis spectra of the GQDs can reflect the size difference, too.^7,8,13,18 The top row of Fig. 2a shows the optical images of the GQDs 1–8 acquired under a daylight lamp, and they were all transparent. The bottom row of Fig. 2a shows the optical images of the corresponding GQDs 1–8 observed under a UV irradiation (302 nm), illustrating that the GQDs 1–8 have fluorescence properties, which are red, orange, yellow, green, cyan, light blue, blue, and purple, respectively. In contrast to the raw GQDs, the result indicates that the GQDs are successfully separated by size through Sephadex G-25 gel column. This should be beneficial for further exploring the relationship between the size and properties of GQDs. As shown in Fig. 2b, the PL spectra of GQDs 1–8 match well with the fluorescence photos. The peak wavelengths of their PL are 587, 565, 554, 483, 462, 452, 385, 384 nm, correspondingly.Open in a separate windowFig. 2(a) The top row is the optical images aqueous suspensions of GQDs 1–8 obtained under daylight lamp; the bottom row is the optical images of the aqueous suspensions GQDs 1–8 acquired under UV irradiation (302 nm). (GQDs-1/red, GQDs-2/orange, GQDs-3/yellow, GQDs-4/green, GQDs-5/cyan, GQDs-6/light blue, GQDs-7/blue, GQDs-8/purple). (b) PL spectra of GQDs 1–8 (the excitation wavelength is 340 nm). (c) UV-vis absorption spectra of GQDs 1–8 (the spectra were normalized at 200 nm for comparison).As shown in Fig. 2c, with the size decreasing, the absorption onset of the GQDs blue-shifted gradually. The absorption around 225 nm corresponding to the π → π* transition of sp² domains in GQDs, and the absorption in the range of 275–325 nm from the n → π* transition of C O groups at the edge of GQDs are also observed clearly, which is similar to the literature.⁸ More specifically, the absorption peak in the range of 275–325 nm becomes more and more obvious with the GQDs size decreasing, indicating the density of carboxylic groups at the edge of GQDs increases from GQDs-1/red to GQDs-8/purple. The reason is that the number of GQD carboxylic groups is directly proportional to its lateral size and the area of GQDs is proportional to the square of its size, as a result the small sized GQDs have higher density of carboxylic groups than the large sized GQDs and present the obvious peak around 275–325 nm.⁸The PL spectra of the as-separated GQDs are shown in Fig. 3 and Fig. S3.^† Comparably, the PL intensities of GQDs 3, GQDs 4, GQDs 5, GQDs 6 (Fig. 3) are stronger than those of others (Fig. S3^†). The PL emission peaks of the GQDs 3 and GQDs 4 shift more obviously than that of GQDs 5 and GQDs 6 with the increase of the excitation wavelength, implying the size distributions of GQDs 3 and GQDs 4 are worse than those of GQDs 5 and GQDs 6. For GQDs 3, as shown in Fig. 3a, there are two peaks in the emission spectra with the excitation wavelength of 360, 380, 400 nm. The left peak is attributed to the π* → n transition of carbonyl or carboxylic and the right peak is attributed to the sp² domains in carbon skeleton. For GQDs 4, as displayed in Fig. 3b, with the excitation wavelength increasing from 300 to 400 nm, the main contribution for the PL is still the sp² domains in carbon skeleton. With the excitation wavelength of 380, 400 nm, two slight shoulders occur in the emission spectra, the left is attributed to the π* → n transition of carbonyl or carboxylic, too. With the decreasing of GQDs size, the PL intensity from the sp² domains gets weak, but the one of π* → n transition increases. The emission peaks of GQDs 5 and GQDs 6 shift slightly (Fig. 3c and d), which is mainly attributed to the π* → n transition of carbonyl or carboxylic, but partly from the sp² domains in carbon skeleton.^8,22Open in a separate windowFig. 3The fluorescence emission spectra of GQDs-3/yellow samples with excitation wavelengths from 360 nm to 520 nm (a), GQDs-4/green with excitation wavelengths from 300 nm to 400 nm (b), GQDs-5/cyan with excitation wavelengths from 280 nm to 380 nm (c), and GQDs-6/light blue samples with excitation wavelengths from 280 nm to 360 nm (d).The PL quantum yields (QYs) of raw and separated GQDs are measured using quinine sulfate as a reference (QY = 57.7%),^3,23 and are summarized in Table S1.^† The QYs of the raw GQDs and GQDs 1–8 are 0.99, 0.611, 0.758, 2.592, 5.905, 1.816, 0.486, 0.259, and 0.199%, respectively. Obviously, the QYs of GQDs 3, GQDs 4, and GQDs 5 are much higher than those of others, but the QYs of GQDs 1, GQDs 2, GQDs 6, GQDs 7, and GQDs 8 are much lower than that of the raw GQDs. This may be resulted from the comprehensive factors from the quantum confinement effect, and the functional groups on the edge of GQDs.In fact, the size and surface functionality of the raw GQDs are the key factors dominating Sephadex G25 gel column separation efficiency. By simply varying the photo-Fenton reaction time, different raw GQDs are prepared. Accordingly, as shown in Fig. S4,^† GQDs assuming different fluorescent colours can be obtained. When the photo-Fenton reaction time was 90 minutes, big sized GQDs with yellow and orange fluorescence can be rarely obtained. Only blue and cyan fluorescence GQDs could be separated using G25 gel chromatography (Fig. S5^†). It can be concluded that the separating extent is seriously depended on the size and surface functionality of GQDs as-obtained via photo-Fenton reaction. Similarly, only the GQDs with blue fluorescence could be separated from the raw material of GQDs prepared by hydrothermal method⁴ using G25 gel chromatography. Recently, various GQDs prepared by reported methods are mono-fluorescence such as blue or green and they are not suitable for the suggested separating technique.^24–26 Thus, the suggested separating technique is not universal for GQDs obtained via different preparing methods.In order to explore the advantages of the as-separated GQDs, raw GQDs and GQDs 4 with the highest QY are used as additivity for the electron acceptor material PCBM, and inverted structure organic ternary hybrid solar cells (Ag/MoO₃/P3HT:PCBM:GQDs/ZnO/ITO) were assembled. The photovoltaic performances of as-fabricated solar cells were characterized, and the results are depicted in Fig. 4 and Table S2.^† The power conversion efficiencies (PCEs) of the solar cells containing raw GQDs and GQDs 4 are of 3.46% and 3.91%, respectively, which are higher than that of the control group (3.07%). Further, the performance of the solar cell with GQDs 4 is even better than that with raw GQDs, which means that the size and size distribution are crucial to the optoelectronic performances. However, the detailed mechanism of the photovoltaic performances of the as-assembled inverted structure organic ternary hybrid solar cells are not clear for us at moment, and will be further addressed in our coming work.Open in a separate windowFig. 4 J–V characteristics of the solar cells based on P3HT:PCBM:GQDs active layers with different GQDs.     

Transition metals enhance prebiotic depsipeptide oligomerization reactions involving histidine

Biochemistry exhibits an intense dependence on metals. Here we show that during dry-down reactions, zinc and a few other transition metals increase the yield of long histidine-containing depsipeptides, which contain both ester and amide linkages. Our results suggest that interactions of proto-peptides with metal ions influenced early chemical evolution.

Transition metals enhance prebiotic proto-peptide oligomerization reactions through direct association with histidine.

Around half of all known proteins associate with metal ions or organometallic cofactors.^1–4 Metals stabilize protein structure (e.g., zinc fingers) and mediate catalysis (nitrogenases), electron transfer (cytochromes), ligand transport (hemoglobin), and signalling (calmodulin). Metals stabilize nucleic acids; around 500 divalent metal cations associate with a single ribosome.⁵ The dependence of biochemistry on metals appears ancient and rooted in chemical evolution, preceding emergence of life on Earth.^6,7 Long-standing questions about the origins of life might be answered by understanding how metals interact with ancestral biopolymers. For example, metals could have affected oligomerization reactions of early proto-polymers, and could have conferred stability and function, in analogy with their roles in extant biochemistry.Depsipeptides, containing mixtures of ester and amide linkages, are plausible ancestors of polypeptides.^8–14 During drying of hydroxy acids and amino acids at mild temperatures (i.e., 65 °C) ester bonds form first and are converted to peptide bonds by ester–amide exchange. Hydroxy acids and amino acids are thought to have been abundant on the prebiotic earth.^15–19Here we tested the hypothesis that interaction with Zn²⁺ or other metal ions with the amino acid histidine (His) might affect rates and extents of depsipeptide formation in dry-down reactions. We observed that Zn²⁺ and other selected transition metals increase yields of long His-containing depsipeptides. The increase in yield is specific for imidazole-containing amino and hydroxy acids and metals that interact directly with them.We previously showed that His is readily incorporated into depsipeptides during dry-down reactions under mildly acidic conditions (pH ∼3) at 85 °C.¹² These conditions are known generally to promote oligomerization in mixtures of hydroxy acids and amino acids into depsipeptides.^8–11 Here, mixtures of glycolic acid (glc) and l-His were reacted under these known reaction conditions in the presence or absence of various metals.Addition of Zn²⁺ led to an increase in the average lengths of His-containing depsipeptides. Depsipeptide oligomers are readily detected by high-performance liquid chromatography (HPLC) using a C18 column (Fig. 1a). Longer oligomers exhibit longer retention times²⁰ allowing us to compare various dry-down reactions. The yield of products with a higher retention times on HPLC is increased following addition of Zn²⁺ to the reaction mixture (Fig. 1a). ¹H NMR analysis confirmed that the distribution of oligomeric species changes with addition of Zn²⁺ to the dry-down reaction (Fig. 1b–d). MS analysis verified the increased abundance of longer His-containing depsipeptides following dry-down with Zn²⁺ (Fig. S1^†). On the other hand, Zn²⁺ decreases the extent of conversion of His into oligomers. While 42% of His monomer converted into oligomers in the absence of Zn²⁺, only 22% of His monomer converted into oligomers in its presence (Fig. 1b–d). Oligomerization is indicated by shifts in the β-proton resonance envelope centered at ∼3.37 ppm and in the imidazole proton envelopes at ∼7.40 ppm and ∼8.68 ppm (Fig. 1b–d). Extent of conversion to oligomers was calculated based on the integrals of residual nonreacted imidazole proton resonances (Fig. 1b–d).Open in a separate windowFig. 1Zinc increases the yield of long His-containing depsipeptides in dry-down reactions. (a) His monomer was dried with glycolic acid (glc) at a 1 : 1 molar ratio at 85 °C for seven days in the presence or absence of Zn²⁺, at a 1 : 1 molar ratio (His : Zn²⁺). Analysis of samples via C18-HPLC showed a dramatic increase in the yield of longer oligomers in the presence of Zn²⁺. (b and d) ¹H NMR spectrum of a mixture of glc and His in D₂O before (b) and after (c and d) dry-down at 85 °C for seven days in the absence (c) or presence (d) of 1 eq. of Zn²⁺. (e) A possible coordination complex between Zn²⁺ and two His monomers.The observed increase in depsipeptide length upon addition of Zn²⁺ might result from direct association between Zn²⁺ and His monomers (Fig. 1e)²¹ because the effect is Zn²⁺ dose-dependent and is maximal at a 1 : 1 molar ratio of Zn²⁺ to His (Fig. S2^†). Specific interaction of Zn²⁺ with His monomer has been reported previously.²² The increased production of long His-containing depsipeptides with increasing Zn²⁺ is reversed when the number of Zn²⁺ equivalents exceeds that of His. Three equivalents of Zn²⁺ completely inhibited oligomerization reactions (Fig. S3^†). The effect of Zn²⁺ on reactivity of His during the dry-down conditions might arise from either a locked chelate conformation or increased electrophilicity of the carbonyl. Importantly, Zn²⁺ did not cause polymerization of His in the absence of glycolic acid (Fig. S4^†).The effect of Zn²⁺ on depsipeptide formation is not a generic effect and is specific to His. We dried-down mixtures of glc with either alanine (Ala) or lysine (Lys). The addition of Zn²⁺ to a 1 : 1 molar ratio with these amino acids does not increase the yield of products in any length range. In fact, Zn²⁺ inhibited depsipeptide formation for both Ala and Lys (Fig. 2).Open in a separate windowFig. 2Zinc does not increase extent of polymerization or length of oligomers of Ala- or Lys-containing depsipeptides in dry-down reactions. Alanine (a) or lysine (b) were dried with glc at a 1 : 1 molar ratio, for one week at 85 °C under unbuffered conditions, in the presence or absence of Zn²⁺, at a 1 : 1 molar ratio of amino acid to Zn²⁺. The addition of Zn²⁺ hindered depsipeptide formation for both amino acids tested, as opposed to the reverse trend observed with His.In addition to Zn²⁺, we investigated the effects of Na⁺, K⁺, Ca²⁺, Mg²⁺, Cu²⁺, and Co²⁺ on the oligomerization of His in depsipeptides. We dried-down mixtures of glc and His in the presence or absence of various metals (1 : 1 molar ratio of M⁺ or M²⁺ to amino acid). Analysis by HPLC showed that Zn²⁺, Cu²⁺, and Co²⁺, but not Na⁺, K⁺, or Mg²⁺, increased the production of longer His-containing depsipeptides (Fig. S5 and S6^†). Ca²⁺ decreased the production of His-containing depsipeptides (Fig. S5^†).Circular dichroism spectroscopy (CD) supported our hypothesis that enhancement of oligomerization of His in the presence of Zn²⁺ results from direct association between monomeric His and Zn²⁺. We added various concentrations of Zn²⁺ to monomeric glc plus His. The CD spectrum inverts at equal molar ratio of Zn²⁺ and His (Fig. 3a). We attribute the inversion to formation of His–Zn²⁺ complex in concert with a change in the conformation of His. An example of a possible complex is shown in Fig. 1e.Open in a separate windowFig. 3Circular dichroism analysis confirms that zinc and several other transition metals interact with His monomer. Glycolic acid (glc) and His were mixed, at a 5 : 1 molar ratio, in 50 mM Tris buffer (pH 7.2). Circular dichroism (CD) spectra were collected for the mixture in the absence or presence of 1 eq. (referring to the amount of His monomer) of (a) Zn²⁺ or (b) various other metals. CD spectra showed a clear shift in the signal of His following addition of Zn²⁺, Ni²⁺, Cu²⁺, and Co²⁺, but not for the other metals tested.CD spectra of glc plus His only report conformational changes of His because glc is achiral. The conformational change upon Zn²⁺ binding is dose dependent; the change in the CD spectra increases with increasing concentrations of Zn²⁺ (Fig. S7^†). Addition of Zn²⁺ to the dry-down product mixture of His-containing depsipeptides resulted in far more subtle changes in the CD spectra, which appears to arise from binding of Zn²⁺ to small amounts of remnant His monomer that was not converted into polymers during the dry-down reaction (Fig. S8^†).¹² In accordance with the observed species-specific impact of metals on dry-down reactions (Fig. S5^†), the inversion of the CD signal of His monomer was also observed for Co²⁺, Cu²⁺, and Ni²⁺, but not for Na⁺, K⁺, Li⁺, Mg²⁺, or Ca²⁺. Thus, it appears that low-lying d-orbitals of metals are important for interaction with His. The differences in the electron configuration between the different metals affect their metal coordination properties. Transition metals are more electronegative and have more oxidation states than alkaline and alkaline-Earth metals, and their valence electrons in the d-shell tend to promote stable coordination complexes. By contrast, Zn²⁺ inhibited oligomerization of Ala or Lys in dry-down reactions. This inhibition is consistent with recent thermodynamic calculations²³ that examined effects of metals on the monomer–oligomer equilibria of glycine. Metals shift the equilibria toward the monomer, particularly at neutral and alkaline pH.²³To determine if oligomerization of imidazole-containing monomers other than His is promoted by Zn²⁺, we dried l-β-imidazole lactic acid (the hydroxy acid analog of His, herein termed his) with glc for one week at 85 °C. The reaction produced polyesters, co-polymers of his and glc (Fig. S9^†). Addition of Zn²⁺ to his and glc dry-down reaction mixtures increased the yield of longer polyester oligomers (Fig. 4a). ¹H NMR analysis of these polyesters indicate that Zn²⁺ did not change the extent of conversion of his monomer into oligomers: 39% of his converted into oligomers in the absence of Zn²⁺ and 38% of his converted into oligomers in its presence (Fig. S10^†). Therefore, Zn²⁺ does not increase the overall oligomeric yield but rather the distribution of product oligomers, increasing the yield of longer oligomers (Fig. 4a and Fig. S10^†). These results imply that a terminal alcohol can support a chelation complex with Zn²⁺, in analogy with the suggested chelation complex of Zn²⁺ by His (compare Fig. 4b to Fig. 1e).Open in a separate windowFig. 4Zinc increases lengths of his-containing polyesters in dry-down reactions. (a) l-β-Imidazole lactic acid (His) was dried with glycolic acid (glc) at a 1 : 1 molar ratio at 85 °C for seven days in the presence or absence of Zn²⁺, at a 1 : 1 molar ratio of his to Zn²⁺. Analysis of samples via C18-HPLC showed a dramatic increase in the yield of longer oligomers in the presence of Zn²⁺. (b) Possible coordination complex between Zn²⁺ and his monomers.Several distinct non-exclusive mechanisms can explain why Zn²⁺ promotes formation of longer His-containing depsipeptides. Dry-down reactions are conducted under mildly acidic conditions (pH ∼ 3), in which the imidazole side chain (pK_a of ∼6) and the α-amino group (pK_a of ∼9) of monomeric His are protonated and the carboxylic acid (pK_a of ∼2) is deprotonated. Deprotonation of α-amino group would be promoted by His coordination of Zn²⁺ (Fig. 1), favoring an intermediate in formation of depsipeptides through ester–amide exchange. Zn²⁺ coordination by His might also lock His in a specific reactive conformation and/or increase the electrophilicity of the His carbonyl group. Zn²⁺ is expected to pull electron density from His and expose the carbonyl to nucleophilic attack (Fig. 1e). Dehydration would promote His coordination with Zn²⁺ by depleting competing water molecules.^21,24 In principle, it is possible that a complex is formed in which glc and His simultaneously chelate Zn²⁺, or in which His and glc-based oligomers chelate Zn²⁺ such that a favored configuration for a nucleophilic attack is reached.The effects of metals on oligomerization of amino acids by methods other than dry-down reactions has been investigated previously.^23,25–30 Concentrated sodium chloride (>3 M) promotes oligomerization in the presence of Cu²⁺, to increase the yield of glycine (Gly)- and Ala-based peptides.²⁵ Various metals can affect oligomerization of chemically activated amino acids (N-carboxyanhydrides).^31,32 Chemical activation studies focused on Gly, the simplest and most reactive amino acid, but resulted in only low yields of very short peptides.^{23,25–28,33–39} It has been proposed that minerals might catalyze dry-down oligomerization of amino acids.^33–39 McKee et al. observed that silica hinders the amidation of Gly in the presence of lactic acid, the hydroxy acid analog of Ala.⁴⁰ However, silica did lead to an enrichment of amide bonds over ester bonds.⁴⁰His may not be a prebiotic amino acid. It has been proposed that the prebiotic chemical ancestor of His might be imidazole-4-acetaldehyde,^41–44 which is produced by Strecker synthesis.^45,46 The His-containing depsipeptides produced here do not appear to bind to Zn²⁺ (Fig. S8^†). This absence of chelation is consistent with the low number and density of His side chains, and the absence of backbone amines at ester linkages. Longer depsipeptides with greater number and density of His residues may bind Zn²⁺ and might lead to emergence of small metalloenzymes.The importance of small proto-metalloproteins on the prebiotic Earth is supported by the cooperative interactions of metals and proteins in extant biology. Mulkidjanian proposed the zinc world theory, according to which the first metabolism was driven by zinc sulfide minerals that catalyzed photochemical reactions.^47–49 Primordial cooperation may have existed between metals and proto-peptides prior to the emergence of coded protein synthesis.^50–53 For instance, amyloidogenic heptapeptides can function as Zn²⁺-dependent esterases.⁵¹ Zn²⁺ promotes fibril formation by His-containing peptides, acting as a catalytic cofactor. Short peptides with acidic residues, such as aspartic acid and glutamic acid,^52,53 could have protected short RNA molecules against Mg²⁺-induced degradation.^54,55 Coordination of metal ions induces peptide conformational changes and supramolecular assembly.^56–60 In addition to effects on peptide self-assembly and function, metal–peptide interactions are utilized for fabrication of nanofiber materials for various applications, including three-dimensional cell culture and tissue engineering.^56,61,62It is generally accepted that Zn²⁺ concentration has remained fairly constant in seawater through time, whereas the concentrations of Co²⁺ and Ni²⁺ were higher in earlier stages of Earth history than in modern seawater.^63–72 If accumulation of metals occurred at shallow lakes or similar environments that were subjected to dry-wet cycling, they might have affected distribution of polymers that formed within these environments in a specific manner. Our results suggest that the close relationship between metals and biopolymers has roots in prebiotic chemistry and shaped their co-evolution.     

Assembly and functionalization of supramolecular polymers from DNA-conjugated squaraine oligomers

DNA conjugated oligomers of organic molecules are candidates for applications in the materials and medical sciences, in diagnostics, in optical devices, for delivery or for the design of complex molecular architectures. Herein, we describe the synthesis and properties of DNA-conjugated squaraine (Sq) oligomers. The oligomers self-assemble into supramolecular polymers that are amenable to further functionalization via DNA hybridization, as shown by the attachment of gold nanoparticles (AuNPs).

The assembly of supramolecular polymers of DNA-linked squaraine oligomers and their subsequent derivatization is described.

While synthetic supramolecular polymers (SPs) were primarily designed to assemble in organic solvents, similar behaviour was later also demonstrated in an aqueous environment.^1,2 The change of solvent polarity offers possibilities to design and develop additional types of supramolecular systems and materials with diverse properties.^3,4 The tuning of such properties, however, remains challenging due to difficulties in the predictability of the self-assembly behaviour of new types of building blocks. These non-covalent interactions, however, are responsible for the dynamic nature of the supramolecular assemblies and, thus, for their structural homogeneity and integrity.^5,6 Growing structural and functional complexity is of particular importance once applications beyond a simple assembly–disassembly process are becoming a focus of interest.⁷ This affects areas like the development of responsive materials,⁸ drug delivery,⁹ molecular sensors¹⁰ and signalling cascades.¹¹ Ultimately, the design of building blocks should aim at predictability of the supramolecular interactions¹² and, at the same time, enable further functionalization of the formed SPs. One very robust way of addressing these prerequisites relies on the use of DNA as the addressable molecular building block.^13,14 Materials based on DNA base-pairing and strand hybridization show great promise for the assembly of defined nanostructures and elaborated molecular systems.^15–17 Increasing efforts are put into the synthesis and construction of hybrid materials, e.g. DNA-functionalized polymers that exhibit diverse properties in hydrogels,¹⁸ responsive drug delivery systems¹⁹ or optoelectronic devices.²⁰Recently, we reported on DNA-grafted supramolecular polymers²¹ by combining oligoarenotides²² and oligonucleotides. These hybrid building blocks allow the formation of supramolecular ribbons,^21,23 nanosheets²⁴ and vesicular constructs.^25,26 Typically, these systems show a high level of reversibility by either thermal denaturation or strand displacement reactions and they respond to external factors (e.g. temperature changes). In addition, the aforementioned supramolecular polymers are amenable to further modification, e.g. for the assembly of light-harvesting photonic wires.²⁷ Both, the ability to control the precise arrangement of functional building blocks and the process of supramolecular assembly of the oligomers, demonstrate the potential of DNA-functionalized materials, as neither pure synthetic supramolecular polymers nor DNA-only based systems can easily attain similar properties.^28,29Long-wavelength, water-compatible supramolecular assemblies are especially attractive for possible applications in the medical sciences and as optoelectronic devices.^30–32 Squaraine-based systems therefore represent ideal candidates for the creation of such “long-wavelength” supramolecular materials.^33–35 Squaraine dyes exhibit molar absorptivities of up to 260 000 M⁻¹ cm⁻¹,³⁶ they absorb and emit light in the long-wavelength region of the visible spectrum and possess the well-documented property of forming aggregates in aqueous solutions.^37,38 Squaraine assemblies designed for biomedical applications are primarily based on copolymer systems. For example, hydrophobic phospholipid bilayers of liposomes (nanovesicles) with embedded squaraine dyes are promising structures for near-infrared fluorescence and photoacoustic tomography imaging.³⁹ Here, we report the preparation of squaraine–DNA block co-oligomers, their assembly into SPs and their further derivatization with AuNPs. †).^36,40 The conjugates contain a varying number of squaraine units. As described below, this number determines whether defined SPs are formed. Formation of the SPs was followed by atomic force microscopy (AFM) and/or transmission electron microscopy (TEM). After supramolecular polymerization, complementary DNA strands modified with gold nanoparticles (AuNPs) were hybridized onto the DNA-modified SPs, as illustrated in Scheme 1. Since AuNPs are easily monitored by TEM imaging, they provide a straightforward tool to visualize the specific functionalization of the SPs via hybridization.⁴¹Sequences of squaraine–DNA oligomers and AuNP-modified DNA strands. The molecular structure of the squaraine derivative (Sq) is shown in Scheme 1

Micro-supercapacitors based on oriented coordination polymer thin films for AC line-filtering

Reported herein is a facile solution-processed substrate-independent approach for preparation of oriented coordination polymer (Co-BTA) thin-film electrodes for on-chip micro-supercapacitors (MSCs). The Co-BTA-MSCs exhibited excellent AC line-filtering performance with an extremely short resistance–capacitance constant, making it capable of replacing aluminum electrolytic capacitors for AC line-filtering applications.

Micro-supercapacitors exhibiting excellent AC line-filtering with oriented coordination polymer thin-film electrodes are fabricated based on a substrate-independent electrode fabrication strategy.

Micro-supercapacitors (MSCs), as important Si-compatible on-chip electrochemical energy storage devices, have attracted rapidly growing attention due to their rapid energy-harvesting features and burst-mode power delivery.^1,2 In the past few years, a variety of materials including carbon nanotubes,³ graphene,⁴ graphene oxide and mesoporous conducting polymers,^5,6 have already been explored to fabricate the electrodes of MSCs for improving their electrochemical performance. Unfortunately, fabrication procedures of most of these active materials suffer from high cost, harsh and complicated processing conditions, as well as easy cracking and delamination of active films,^1,4 extremely limiting their commercial applications. Moreover, their performances are unsatisfactory for alternating current (AC) line-filtering, which is a key parameter to implement high-frequency operation in most line-powered devices.^7–9For AC line-filtering, capacitors need to respond harmonically at 120 Hz to attenuate the leftover AC ripples on direct current voltage busses.¹⁰ Notably, the development of more compact and miniaturized capacitors to replace traditional aluminum electrolytic capacitors (AECs) for AC line-filtering has become one of the major tasks for future electronics.¹¹ However, typical supercapacitors are incapable for AC line-filtering at this frequency due to their limited ion diffusion and charge transfer efficiency, corresponding to the unsuitable architectures and low conductivity of electrode materials.^10–12 Therefore, the design and fabrication of highly conductive electrodes with optimized architectures for facial electron/ion transportation is crucial for improving the performance of MSCs in AC line-filtering.^12,13 It is worth mentioning that great advancements have been achieved by utilizing vertically oriented graphene sheets as well as 3-dimensional graphene/carbon nanotube carpets prepared by chemical vapor deposition (CVD),^7,8 yielding efficient filtering of 120 Hz AC with short resistance–capacitance (RC) time constants of less than 0.2 ms, which is competitive with those of porous carbon-based supercapacitors (RC time constant = 1 s) as well as AECs (RC time constant = 8.3 ms).⁸ However, the CVD method necessitated in the fabrication of graphene/carbon nanotube electrodes suffers from high cost and complicate procedures.Coordination polymers with an unrivalled degree of structural and property tunability which could be realized by facial procedures, are promising candidates for energy storage.^14,15 Recently, a remarkable achievement which demonstrated a facile and low-cost solution-processed method towards on-chip MSCs based on an azulene-bridged coordination polymer framework (PiCBA) on a Si wafer-supported Au surface was reported.¹⁴ Nevertheless, the reported preparation of coordination polymer film exhibited strong dependence on the surface chemistry (functionality) of the substrate and further improvement of their electrochemical stability was needed. Therefore, the development of substrate-independent fabrication strategies of large-scale and uniform coordination polymer films is in great need not only for fundamental studies, but also for technological applications especially in electronics.Herein, we demonstrate a facial solution-based substrate-independent approach to fabricate oriented coordination polymer (Co-BTA) thin-film electrodes. Remarkably, rigid and flexible Co-BTA-based MSCs with excellent electrochemical stability and AC line-filtering performance were realized, indicating great application potential in micro-supercapacitors.As demonstrated in Fig. 1a–c, a large scale and continuous Co-BTA coordination polymer film composed of one dimensional (1D) molecules ([Co(1,2,4,5-bta)]_n) was prepared at the air–liquid interface through a coordination reaction between 1,2,4,5-benzenetetramine tetrahydrochloride (BTA) and cobalt acetate tetrahydrate (Co(CH₃COO)₂·4H₂O). Notably, the preparation of Co-BTA film is basing on mild conditions and independent of any substrates. The resulting film can be transferred onto any supports including rigid silicon (Si) wafer, glass, as well as flexible PET substrate, indicating great substrate-independence and making it practically applicable for various applications. Besides of a brown film formed at the air–liquid interface, a powder product is also obtained at the bottom of the reaction bottle.Open in a separate windowFig. 1(a) Synthesis of Co-BTA through the coordination reaction between BTA and cobalt ions. (b) Illustration of the gas–liquid interface growth of Co-BTA film. (c) Photographs of the reaction system before and after the coordination reaction.To study the morphology of the resulting Co-BTA film, the brown film was transferred onto a SiO₂/Si wafer by immersing the wafer down to the reaction mixture and subsequently lifting the film up. The scanning electron microscopy (SEM) image reveals a highly uniform and large-scale distribution of the obtained film without cracks or wrinkles (Fig. 2a), which is superior to other reported coordination polymer films obtained via a similar method.¹⁶ An average thickness of approximately 60 nm of the Co-BTA film is observed from the cross-sectional SEM image as shown in Fig. 2b. Interestingly, thickness of the obtained coordination polymer film could be well controlled and Co-BTA films with thicknesses up to several hundred nanometers could be well prepared by adjusting the ratio of raw materials (Fig. 2c and d).Open in a separate windowFig. 2(a) Planar SEM image of Co-BTA film. Cross-sectional SEM images of Co-BTA films with a thickness of (b) 60 nm, (c) 160 nm and (d) 260 nm.To investigate the structure information of the resulting Co-BTA and further explore the coordination reaction, characterizations including powder X-ray diffraction measurements (PXRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) were carried out. The PXRD pattern of Co-BTA powder shown in Fig. S1a^† is in great agreement with that simulated from the crystal structure of Ni(dhbq)·nH₂O (Fig. S1b^†), suggesting that Co-BTA and Ni(dhbq)·nH₂O is isostructural and forms 1D structures with straight infinite chain extends.¹⁷ More interestingly, PXRD measurements employing two different scattering geometries (Fig. S2^†) on the Co-BTA thin-film demonstrate two quite different diffraction patterns. As observed in Fig. 3a, the diffraction pattern observed for the out-of-plane scattering geometry exhibits three characteristic peaks of the Co-BTA film at ∼12°, 24° and 36°, which are corresponding to (001), (002) and (003), respectively. In contrast, the in-plane PXRD profile employing grazing-incidence XRD (GIXRD) technique at an incident angle (α) of 0.2° demonstrates a main peak at ∼18°, which is assigned to the (110) diffraction peak. Different diffraction peaks observed through these two XRD scattering geometries indicate an orientation nature of the as-prepared Co-BTA film,¹⁸ which exhibits better crystallinity compared with the powder Co-BTA product. In addition, the N 1s core level spectrum for Co-BTA film exhibit one typical peak at 399.1 eV, which is corresponding to the amido coordinated with Co^II, indicating the strong coordination between Co^II and BTA (Fig. 3b). The weak peak at ∼401 eV is assigned to N–O due to the oxidation of ligand BTA in ambient environment before reaction. The atomic ratio of N : Co is calculated to be 3.53 : 1 for Co-BTA film and 3.71 : 1 for Co-BTA powder respectively (Fig. S3 and Table S1^†), which is close to the theoretical stoichiometric ratio (4 : 1) for Co-BTA structure, suggesting a high degree of coordination in the resulting product through one Co cation and two benzenetetramine groups. Moreover, the disappearance of two characteristic N–H stretching modes from –NH₂ after the coordination reaction whereas the phenyl-related vibration still exists, further confirms the existence of –NH– in the product through the loss of one H per –NH₂ (Fig. S4^†).¹⁹Open in a separate windowFig. 3(a) PXRD profiles of out-of-plane XRD, in-plane XRD and simulated PXRD pattern of Ni(dhbq)·nH₂O,¹⁷ respectively. *SiO₂/Si substrate. (b) N 1s core level spectra of the Co-BTA film.On the basis of facial fabrication, substrate independence, highly orientation nature, low band gap (1.68 eV, calculated from Fig. S5^†) and excellent stability in acid environment (Fig. S6^†), the resulting Co-BTA film is considered as a promising candidate for MSCs application. Fig. 4a schematically depicts the stepwise fabrication of a planar Co-BTA film based MSC on a SiO₂/Si wafer and its electrochemical performance is first examined by cyclic voltammetry (CV) with scan rates ranging from 50 mV s⁻¹ to 1000 V s⁻¹ (Fig. 4b and c). At a low scan rate of 50 mV s⁻¹, the 60 nm-thick Co-BTA film based MSC exhibited a pronounced pseudocapacitive effect, implying the occurance of faradaic reaction.²⁰ With the increase of scan rate, a gradual transition of the CV curves from the pseudocapacitive to the typical electrical double-layer capacitive behavior with a nearly rectangular CV shape was observed. Remarkably, the device exhibited a maximum volumetric capacitance of 23.1 F cm⁻³ at 50 mV s⁻¹, which is comparable with those of reported carbon- or graphene-based MSCs (Table S2^†), e.g., onion-like carbon,²¹ vertically oriented graphene,⁸ and carbon nanotubes/graphene.⁷ Even though a trend that C_V decreased gradually with increasing scan rate was observed, the Co-BTA-based electrode still delivered a C_V of 2.7 F cm⁻³ even at a high scan rate of 1000 V s⁻¹, suggesting an excellent capacitive performance of this Co-BTA-based MSC device.⁷Open in a separate windowFig. 4(a) Schematic illustration of the fabrication of MSC device with the Co-BTA film electrode. (b) CV curves of Co-BTA-based MSCs in the H₂SO₄–PVA gel electrolyte at different scan rates. (c) C_V evolution of the MSCs at different scan rates.Electrochemical impedance spectroscopy (EIS) measurements were performed to evaluate the charge transport properties within the Co-BTA-based MSCs. The Nyquist plot shown in Fig. S7^† indicated the kinetic features of electron transfer/ion diffusion at the electrode, from which an almost straight line especially in the low frequency region is observed. Notably, the plot shows a closed 90° slope without a charge transport semicircle at high frequency which is corresponding to an almost ideal capacitive ion diffusion mechanism, due to the excellent charge transfer property of the oriented Co-BTA electrode film. Moreover, this microdevice exhibited a low equivalent series resistance of 13.48 Ω (Fig. S7^† (inset)), further suggesting the ultrafast ion diffusion characteristic in such a Co-BTA-based-MSC.²² It''s suggested that the unique kinetic feature of fast ion diffusion and charge transfer benefits from the intrinsic characteristics of the oriented polymer film composed of 1D molecules, which can not only facilitate rapid ionic diffusion but also facilitate the interfacial charge transfer and faradaic redox reaction between the electrode material and electrolyte.What''s more, the dependence of the phase angle on frequency shown in Fig. 5a delivered a high characteristic frequency f₀ of 6812 Hz at the phase angle of −45° (the resistance and reactance of the device have equal magnitudes),¹⁰ which is much higher than that of an active carbon supercapacitor (5 Hz),²³ sulfur-doped graphene MSCs (3836 Hz),²² or an azulene-bridged coordination polymer framework based MSCs (PiCBA-MSCs) (3620 Hz) and so on,¹⁴ as summarized in Table S2.^† Moreover, a max phase angle of −80° at a frequency of 18 Hz is observed, indicating the performance of this Co-BTA based MSCs is 89% of that of an ideal capacitor. Importantly, a large impedance phase angle of −78.6° was obtained at a frequency of 120 Hz, which is the largest reported value for coordination polymer based MSCs (Table S2^†), suggesting an excellent AC line-filtering performance of our microdevice.⁷ To further conform the ultrahigh fast ion diffusion in Co-BTA-based-MSCs, the relaxation time constant τ₀ (τ₀ = 1/f₀, the minimum time needed to discharge all the energy from the device with an efficiency of greater than 50% of its max. value) was calculated to be only 0.15 ms (6812 Hz), which is orders of magnitude higher than that of conventional electrical double-layer capacitors (1 s),⁸ activated or onion-like carbon MSCs (<200 ms, <10 ms),^21,23 and much shorter than those of MSCs based on carbon nanotubes/reduced graphene oxide (4.8 ms) as well as azulene-bridged PiCBA coordination polymer framework film (0.27 ms).^14,24 Moreover, a short RC time constant (τ_RC) of 0.32 ms was obtained (Fig. 5b) through a series-RC circuit model, making it capable of replacing AECs for AC line-filtering application. To the best of our knowledge, this is the first report of coordination polymer-based MSCs exhibiting such a small relaxation time constant and RC time constant.Open in a separate windowFig. 5(a) Impedance phase angle on the frequency for the Co-BTA-based microdevices. (b) Plot of capacitance (C_V′ = volumetric real capacitance and C_V′′ = imaginary capacitance) versus the frequency of Co-BTA-based microdevices. (c) Cycling stability of Co-BTA film with 10 000 cycles at the scan rate of 50 V s⁻¹. Inset displays the CV curves at the first, five thousandth and ten thousandth cycle, respectively. (d) Ragone plots for Co-BTA film, compared with commercially applied Li-thin-film batteries,²¹ electrolytic capacitors,² CNT-graphene carpets,²⁴ PiCBA coordination polymer and MXene-reduced graphene oxide.^14,25Impressively, this oriented electrode structure exhibits excellent long-term electrochemical stability with ∼96.3% capacitance retention even after 10 000 cycles of charging/discharging at a scan rate of 50 V s⁻¹ (Fig. 5c), which has also been confirmed by comparing the CV curves before and after testing for 10 000 cycles (inset of Fig. 5c). It''s worth pointing out that the as-made Co-BTA-based MSCs exhibit the best electrochemical stability among reported MSCs with coordination polymer electrodes.¹⁴ On the basis of the above discussion, it is reasonable to conclude that the ultrahigh fast ion diffusion/charge transfer in Co-BTA-based-MSCs attributed to the oriented architecture of Co-BTA thin-film electrodes, the excellent AC line-filtering performance, as well as remarkable electrochemical stability contributes to the excellent performances of Co-BTA-based-MSCs. Moreover, the power density and energy density of the as-made device is calculated and compared with that of MSCs based on other electrode materials to evaluate the energy storage performance of the Co-BTA based MSCs. The Ragone plot in Fig. 5d reveals a high power density of 1056 W cm⁻³ for our device, which is at least five orders of magnitude higher than that of commercial thin-film lithium batteries. What''s more, our device exhibits an energy density of up to 1.6 mW h cm⁻³ at 50 mV s⁻¹, which is at least one order of magnitude higher than that obtained for MSCs based on CNTs-graphene carpet and high-power electrolytic capacitors.^2,24To further demonstrate the substrate independence of this fabrication strategy, flexible Co-BTA-based-MSC device was fabricated and investigated basing on a flexible polyethylene terephthalate (PET) substrate instead of rigid Si substrate in the same way (Fig. S8–S10^†). The as-fabricated device exhibited a maximum volumetric capacitance of 22.0 F cm⁻³ at 50 mV s⁻¹, a short relaxation time constant τ₀ of 0.15 ms and a RC time constant (τ_RC) of 0.42 ms, which are close to the properties of devices with a Si substrate, confirming the substrate independence of this fabrication scheme. As a proof-of-concept application, bending tests were carried out and the bended device (radius = 1 cm) exhibited a small relaxation time constant τ₀ of 0.21 ms and RC time constant (τ_RC) of 0.42 ms, suggesting that the Co-BTA-based MSC with PET substrate in a bended state still delivers a good ion diffusion and AC line-filtering performance.In conclusion, we have demonstrated a facile method that can be used to construct large scale and highly oriented uniform Co-BTA coordination polymer thin films using a very convenient and fast process. With this method, Co-BTA-based MSCs are fabricated without any dependence of the substrate. The as-fabricated MSCs on Si substrate exhibit high specific capacitance, energy density as well as excellent electrochemical stability. Particularly, the fabricated Co-BTA based MSCs deliver excellent AC line-filtering performance with an extremely short RC time of 0.32 ms, attributed to the facilitated ion diffusion beneficial from the oriented architecture of Co-BTA thin film. The high-performance electrochemical properties of Co-BTA-MSCs makes Co-BTA films promising materials to provide more compact AC filtering units for future electronic devices.     

Coumarin-based fluorescent ‘AND’ logic gate probes for the detection of homocysteine and a chosen biological analyte

With this research we set out to develop a number of coumarin-based ‘AND’ logic fluorescence probes that were capable of detecting a chosen analyte in the presence of HCys. Probe JEG-CAB was constructed by attaching the ONOO⁻ reactive unit, benzyl boronate ester, to a HCys/Cys reactive fluorescent probe, CAH. Similarly, the core unit CAH was functionalised with the nitroreductase (NTR) reactive p-nitrobenzyl unit to produce probe JEG-CAN. Both, JEG-CAB and JEG-CAN exhibited a significant fluorescence increase when exposed to either HCys and ONOO⁻ (JEG-CAB) or HCys and NTR (JEG-CAN) thus demonstrating their effectiveness to function as AND logic gates for HCys and a chosen analyte.

With this research we set out to develop of a number of coumarin-based ‘AND’ logic fluorescence probes that were capable of detecting a chosen analyte in the presence of HCys.

Homocysteine (HCys) is a non-proteinogenic amino acid, formed from the de-methylation of methionine,¹ which is then converted into cysteine (Cys) via a vitamin B₆ cofactor. Typical physiological concentrations of HCys range between 5–15 μmol L⁻¹.² However, elevated levels of HCys (>15 μmol L⁻¹), which is known as hyperhomocysteinemia (hHCys),³ have been associated with pregnancy disorders, Alzheimer''s disease, cardiovascular disease and neurodegenerative diseases (NDs).^4–6 It is believed that the main cause of HCys induced toxicity is through the non-enzymatic modification of proteins. This is achieved through irreversible covalent attachment of the predominant metabolite of HCys, homocysteine thiolactone (HTL), to lysine residues; a phenomenon known as ‘protein N-homocysteinylation’ that results in the loss of a proteins structural integrity leading to loss of enzymatic function and aggregation.⁷A number of fluorescent sensors have been developed for the detection of HCys to help improve our understanding of its role in biological systems.^8–11 However, these fluorescent probes have focused on the detection of a single biomarker (HCys), however, processes associated with HCys induced toxicity often involve more than one biochemical species. For example, it has been reported that peroxynitrite (ONOO⁻) and nitric oxide (NO˙) play a significant role in HCys-mediated apoptosis in trigeminal sensory neurons¹² and HCys has been reported to induce cardiomyocytes cell death through the generation of ONOO⁻.¹³ The production of ONOO⁻ is believed to be the result of an increased production of superoxide (O₂˙⁻) by HCys activating the enzyme NADPH oxidase.^14–16 This increased production of O₂˙⁻ leads to a reduction in the bioavailability of NO˙ by increasing the formation of ONOO⁻ (NO˙ + O₂˙⁻ → ONOO⁻).¹⁷ The reported ONOO⁻ concentrations in vivo are believed to be approximately 50 μM but, higher concentrations of 500 μM have been found in macrophages.^18,19 Furthermore, hypoxia has been reported to facilitate HCys production in vitamin-deficient diets²⁰ where hypoxia leads to an upregulation of nitroreductase (NTR) – a reductive enzyme upregulated in cells under hypoxic stress.^21,22 Therefore, the development of tools that enable an understanding of the relationship of HCys with these biologically important species would be highly desirable.To achieve this, a number of fluorescent probes have been developed that are capable of detecting two or more analytes.²³ These include AND logic gate based-fluorescence probes, which require both analytes to work in tandem to produce a measurable optical output.^24–28 In our group, we have developed several ‘AND’ reaction-based probes for the detection of ROS/RNS and a second analyte.^29–32 These ‘AND’ logic scaffolds have been used to detect two analytes within the same biological system.^24,33Owing to the pathological role of HCys, we set out to develop the first example of a fluorescent probe for the detection of HCys and biological related analyte. Aiming towards that target, we became interested in a previously reported coumarin-based fluorescent probe developed by Hong et al.CAH, with a salicylaldehyde (Fig. 1).³⁴ Salicylaldehyde is a known reactive unit towards HCys/Cys, therefore we believed CAH could be used as a scaffold for the development of ‘AND’-based systems for the detection of HCys/Cys and a second analyte.³⁴ In the presence of HCys, CAH exhibited a ‘turn-on’ fluorescence response which is attributed to the nucleophilic nature of the nitrogen and sulfur atoms resulting in thiazine ring formation (Scheme S1, Fig. S1 and S2^†).^34–36Open in a separate windowFig. 1(a) CAH – a core fluorescent unit that enables the synthesis of ‘AND’ based fluorescent probe for the detection of HCys/Cys and a second analyte. (b) JEG-CAB enables the detection of HCys/Cys and (ROS/RNS) while (c) JEG-CAN enables the detection of HCys/Cys and NTR.We believed that CAH was a useful core unit that can be used to introduce the chosen reactive chemical trigger on the phenol for the detection of the corresponding analyte with HCys/Cys. Owing to the relationship between HCys and ONOO⁻/NTR, we set out on the development of a HCys AND ONOO⁻ probe and a HCys AND NTR probe.Therefore, we set out to prepare JEG-CAB and JEG-CAN, which are able to detect HCys/Cys and peroxynitrite (ONOO⁻) or nitroreductase (NTR), respectively (Scheme 1). For JEG-CAB, a benzyl boronate ester was introduced as a ONOO⁻ reactive unit.³⁷ For JEG-CAN, a p-nitrobenzyl group was installed as it is known to be an effective substrate for NTR.^38–40Open in a separate windowScheme 1Synthesis of target probe JEG-CAB and JEG-CAN.To afford CAH, compound 2 was synthesized by refluxing umbelliferone and acetic anhydride at 140 °C. Compound 2 was then dissolved in trifluoroacetic acid at 0 °C followed by the addition of hexamethylenetetramine (HMTA). The mixture was heated to reflux overnight and the solvent was then removed. The intermediate was then hydrolyzed in H₂O for 30 min at 60 °C. Upon isolating CAH, it was then alkylated using 4-bromomethylphenylboronic acid pinacol ester and K₂CO₃ in DMF at r.t. to afford JEG-CAB in 51% yield. JEG-CAN was produced by alkylating CAH using 4-nitrobenzyl bromide and K₂CO₃ in DMF at r.t. to give 49% yield (Scheme 1).We then evaluated the ability of JEG-CAB to detect ONOO⁻ ‘AND’ HCys in PBS buffer solution (10 mM, pH 7.40). The maximum absorption of JEG-CAB at 336 nm shifted to 323 nm with the addition of HCys and then slightly shifted to 328 nm following the addition of ONOO⁻ (Fig. S3^†). As shown in Fig. 2, JEG-CAB was initially non-fluorescent, but the addition of HCys (1 mM) led to a small increase in fluorescence intensity, the subsequent additions of ONOO⁻ (0–24 μM) led to a significant increase in fluorescence intensity (>17-fold, see Fig. S5^†). These results demonstrated the requirement for both ONOO⁻ ‘AND’ HCys to obtain a significant turn ‘‘on’’ fluorescence response.Open in a separate windowFig. 2Fluorescence spectra of JEG-CAB (15 μM) with addition of HCys (1 mM) and incubated for 40 min then measured. Followed by incremental additions of ONOO⁻ (0–24 μM). The data was obtained in PBS buffer solution (pH 7.40, 10 mM) at 25 °C. λ_ex = 371 (bandwidth 20) nm. Dashed line represents JEG-CAB and Hcys addition only. Blue line represents highest intensity after addition of ONOO⁻.The addition of HCys and ONOO⁻ were then performed in reverse where JEG-CAB exhibited a negligible increase in fluorescence intensity upon addition of ONOO⁻ (16 μM). However, in a similar manner to that shown in Fig. 2, a large increase in fluorescence intensity was produced after the subsequent addition of HCys (0–5.5 mM) (Fig. 3 and S6^†). LC-MS experiments were carried out to ascertain the reaction mechanism and the results confirmed the sequential formation of the thiazine ring in the presence of HCys followed by boronate ester cleavage in the presence of ONOO⁻ or vice versa (Scheme S2 and Fig. S19–S21^†).Open in a separate windowFig. 3Fluorescence spectra of JEG-CAB (15 μM) with addition of ONOO⁻ (16 μM) and followed by incremental additions of HCys (0–5.5 mM) measurements were taken after 40 min of both additions. The data was obtained in PBS buffer solution (pH 7.40, 10 mM) at 25 °C. λ_ex = 371 (bandwidth 20) nm. Dashed line represents JEG-CAB and ONOO⁻ addition only. Blue line represents highest intensity after addition of HCys.As expected, probe JEG-CAB was shown to have excellent selectivity with ONOO⁻ against other ROS in the presence of HCys (1 mM) (Fig. S9 and S10^†). Furthermore, JEG-CAB exhibited a high degree of selectivity towards a series of amino acids where only HCys and Cys led to a fluorescence response in the presence of ONOO⁻. This is due to the formation of stable five or six-membered thiazine rings (Fig. S7 and S8^†).³⁴We then evaluated the changes in the fluorescence of JEG-CAN with both HCys and NTR in PBS buffer solution (10 mM, pH 7.40, containing 1% DMSO). As shown in Fig. 4, addition of HCys led to a small increase in fluorescence intensity. However, subsequent addition of NTR (4 μg mL⁻¹) led to a large time dependant increase in fluorescence intensity. To ensure both analytes were required, NTR and NADPH was kept constant (4 μg mL⁻¹ and 400 μM respectively) resulting in a 3.4 fold fluorescence increase (Fig. 5). We attribute the large initial increase to background fluorescence of NADPH.⁴¹ NTR then facilitates reduction of the nitro group of JEG-CAN releasing the core probe CAHvia a fragmentation cascade (Scheme S3^†).^38,42 Subsequent addition of HCys (2.0 mM) led to a 2 fold increase in fluorescence intensity. Again, LC-MS experiments confirmed the proposed reaction mechanism (Fig. S22^†).Open in a separate windowFig. 4Fluorescence spectra of JEG-CAN (15 μM) with initial addition of HCys (2 mM) and incubated for 60 min. Followed by addition of nitroreductase (4 μg mL⁻¹) and NADPH (400 μM) and measured over 90 min in PBS buffer solution (pH = 7.40, 10 mM, containing 1% DMSO). λ_ex = 363 nm. Ex slit: 5 nm and em slit: 5 nm. Dashed line represents JEG-CAN and HCys addition only. Blue line represents highest intensity after addition of NTR.Open in a separate windowFig. 5Fluorescence spectra of JEG-CAN (15 μM) with initial addition of nitroreductase (4 μg mL⁻¹) and NADPH (400 μM) and incubated for 60 min. Followed by addition HCys (2 mM) and measured over 90 min in PBS buffer solution (pH = 7.40, 10 mM, containing 1% DMSO). λ_ex = 363 nm. Ex slit: 5 nm and em slit: 5 nm. Dashed line represents JEG-CAN and NTR addition only. Blue line represents highest intensity after addition of HCys.Kinetic studies for JEG-CAN with both NTR and HCys were carried out (Fig. S11–S18^†) where it is clear that JEG-CAN exhibits a dose dependant fluorescence increase in response of both HCys and NTR.Unfortunately, the probes failed to give good data in cells, which could be due to their short excitation wavelengths or the extremely low intracellular HCys concentrations (5–15 μM). We are now pursuing the development ‘AND’ logic fluorescence probes with longer excitation and emission wavelengths suitable for in vitro and in vivo applications.In summary, we have developed two coumarin-based ‘AND’ logic fluorescence probes (JEG-CAB and JEG-CAN) for the detection of HCys/Cys and ONOO⁻ or NTR, respectively. CAH is a useful platform that enables easy modification for the development of ‘AND’-based fluorescent probes for the detection of HCys/Cys and a second analyte. Both JEG-CAB and JEG-CAN were shown to be ‘AND’-based fluorescent probes.