In vitro behavior of osteoblast-like cells on fluoridated hydroxyapatite coatings

In this work, fluoridated hydroxyapatite (Ca10(PO4)6Fx(OH)(2-x) or FHA) coatings are prepared by sol-gel method for study of the influence of F content on the behavior of osteoblast-like cells. The results show that the cells well attach and proliferate on the FHA coatings studied (Ca10(PO4)6F(0.67-2.00)(OH)(0-1.33)). With increasing F content in the FHA coatings, percentage of cell in S period increases, indicating F in the coating favors the proliferation process of the cells. On the other hand, the proliferation rate increases inversely with zeta potential of the coating surface. As tested from the MTT of the cells cultured in the leaching out solution, increase of F content in the FHA coatings results in a slight decrease in cell proliferation rate, which is most probably due to reduction in release of Ca2+ ions. As a compromise among cell attachment, cell proliferation, apatite deposition and ability to resist dissolution, it is suggested that FHA coatings (Ca10(PO4)6Fx(OH)(2-x)) with x in the range of 0.67-1.48, from the results of this study, may be most suitable for real case implantation.     

In vitro response of tumour cells to non-uniform irradiation

This study examines differences in tumour cellular response using clonogenic cell survival between uniform and non-uniform irradiation. Cells were irradiated with a 6 MV x-ray intensity-modulated beam, in a single large flask (i.e. intercellular communication is possible) or in three small flasks (i.e. intercellular communication is inhibited across the dose gradient). For non-small-cell lung cancer and melanoma cell lines, the dose response over the entire cell culture was significantly different between freely communicating cell cultures and those with inhibited communication across the dose non-uniformity. Communicating cells exhibited poorer survival in the low dose region of the field but improved survival in the high dose region. In general, the response to non-uniform irradiation appeared to 'average out' over the entire cell culture. This was not seen when intercellular communication was inhibited. The results add strength to the body of evidence regarding bystander effects and the inter-dependence of cellular response.     

In vitro response of human T cells to Pseudomonas aeruginosa

Pseudomonas aeruginosa is a gram-negative bacillus that is a major cause of morbidity and mortality in immunosuppressed patients, burn patients, and patients with cystic fibrosis. Although immunity to these bacteria has been associated with serum antibody, more recent evidence suggests that T-cell-mediated immunity may also be important. To evaluate human T-cell responsiveness to these bacteria, the optimal conditions were determined for in vitro proliferation of human peripheral blood lymphocytes and T-lymphocytes to Fisher-Devlin immunotype 1 P. aeruginosa. The proliferative response of normal adult peripheral blood lymphocytes to heat-killed P. aeruginosa was studied in 34 subjects (range, 7,600 to 111,500 net cpm). Analysis of cell subpopulations indicated that T-lymphocytes are the major proliferating cells and that this response is enhanced by the presence of adherent cells. Data from fetal cord lymphocyte responses suggest that the proliferation seen in normal adult lymphocytes is induced by antigenic and not mitogenic stimulation.     

In vitro testing of the potential for orthopedic bone cements to cause apoptosis of osteoblast-like cells.

The purpose of this study was to investigate in vitro the apoptosis- and/or necrosis-inducing potential of polymethylmethacrylate (PMMA)-based bone cements for prosthetic surgery. Four bone cements widely used in orthopedics were tested as extracts onto osteoblast-like MG-63 cells and for comparison, HL-60 cells, which are remarkably sensitive to apoptotic stimuli. Neutral red uptake (NRU) was used to measure cell viability while Hoechst 33258 staining was used to detect DNA content. Apoptosis was characterized using a BrdU-based ELISA assay for DNA fragmentation and examined by fluorescence microscopy using acridine orange and propidium iodide staining of nuclei. The generation of reactive oxygen species (ROS), which could mediate apoptosis, was verified using dichlorofluorescein-diacetate (DCFH-DA) oxidation to DCF. After 24 h of challenge of the cells with the four cement extracts, the viability of either MG-63 or HL-60 cells was found to be unaltered, as recorded by NRU. Apoptotic cell death was induced by three cements in HL-60, whereas MG-63 cells were significantly affected by the four cements tested: the finding of DNA fragments both in the cytoplasm and supernatants of MG-63 after 24 h demonstrated that these cells underwent late-apoptosis secondary necrosis. Fluorescent staining of the nuclei confirmed the results obtained with the ELISA test. Oxygen free radicals were elicited by two cements in HL-60 cells, while MG-63 did not generate ROS in response to cements. This study helps to gain more insight into the mechanism of cell death induced by PMMA-based cements and suggests apoptosis of osteoblasts as a part of the tissue reaction around cemented prostheses.     

Human osteoblast-like cells response to nanofunctionalized surfaces for tissue engineering

Cells are sensitive both to the micro/nanotopographic and chemical features of their surrounding environment. The engineering of the surface properties of biomaterials is then critical to develop bioactive devices with which to elicit appropriate cellular responses. To this regard, the layer by layer (LBL) self assembly technique represents a simple and versatile method to modify surface properties by the deposition of ultrathin films with specific and predetermined properties. In this work biomimetic coatings containing fibronectin, an adhesive glycoprotein of the extracellular matrix, were assembled by means of the LBL technique, and tested for the growth of MG63 human osteoblast-like cells, in order to evaluate their potential for the treatment of materials employed in bone-tissue engineering. As a first step the assembly process was optimized by quartz crystal microbalance measurements and subsequently was repeated on nickel/titanium, silicon and glass samples. The results obtained from the investigation of cell response to the modified surfaces, put in evidence that the deposited nanostructured ultrathin films are effective in promoting cell proliferation. Our results show the high potential of the developed bioactive coatings for the engineering of biomimetic implants and for the optimization of their integration with the surrounding tissues.     

Response of rat osteoblast-like cells to microstructured model surfaces in vitro

The role of surface microtopography in combination with different surface wettability for rat calvaria cell differentiation was examined. Mineralization and alkaline phosphatase (ALP) activity of rat calvaria cells on flat polydimethylsiloxane (PDMS) or PDMS contained pyramids which were either hydrophilic or hydrophobic were compared. ALP expressing cells were more frequent on hydrophilic PDMS contained pyramids. ALP activity, peaked at day 9, was highest for hydrophilic pyramids followed by hydrophobic pyramids and flat hydrophilic PDMS surfaces. A similar pattern was obtained with respect to mineralized nodules. These observations showed that micro-sized surface features promote differentiation of rat calvaria cells. Further, hydrophilic surfaces are more prone to stimulate differentiation in comparison with hydrophobic surfaces. The results suggest that both material surface chemistry and topography affect osteoblast differentiation.     

In vitro response of peripheral blood mononuclear cells to phytohemagglutinin and interleukin-2

The serological determination of class II antigens is still a mandatory test prior to allotransplantation. It is known that these antigens are normally expressed on B lymphocytes and monocytes. The B lymphocytes that constitute 10% to 15% of total blood lymphocytes are the cells currently used for HLA-DR typing. To avoid HLA-DR typing difficulties, or even impossibilities that are frequently encountered among some patient groups, we studied the response of peripheral blood mononuclear cells--as an alternative source of cells for class II antigen typing--to in vitro mitogen and interleukin-2 activation and propagation. Although the patients included in this study were selected having previously known HLA-DR typing difficulties, all could be adequately typed by this method.     

In vitro effects on MG63 osteoblast-like cells following contact with two roughness-differing fluorohydroxyapatite-coated titanium alloys

The chances of integration between an implant and the surrounding bone tissue depend on the surface characteristics of the implant itself. Particularly, chemical composition and surface roughness of the material have emerged as crucial factors in affecting the behaviour of cells in contact with the material. Among various surfaces, calcium phosphate coatings seem to favour a rapid initial integration, but their dissolution by extracellular fluids raises some concern about the long-term stability at the bone-implant interface. Fluorinated apatites are known to be more stable than other ceramic coatings, but, at present, little is known on their effects on human cells. In this study, MG63 osteoblast-like cells were seeded onto two fluorohydroxyapatite (FHA)-coated titanium alloy (Ti6Al4V) materials differing in roughness, respectively, LR-FHA (Ra = 5.6 microm) and HR-FHA (Ra = 21.2 microm). Quantification of the cells in contact with the FHA-coated materials by conventional methods involved some technical difficulties, on which we report. Only the indirect esteem by the measure of total content of proteins and a procedure based on cell count, following a double enzymatic treatment to detach the cells, offered plain results, indicating no significant differences between cellular growth in contact with test materials and with plastic control. Differentiation and functionality of the cells were comparatively evaluated by analysis of alkaline phosphatase activity and osteocalcin production. As far as osteocalcin release is concerned, only slight variations were detected on FHA-coated materials in comparison with the control. Both types of coatings showed a significant increase in alkaline phosphatase activity with respect to the control, the roughest surface exhibiting a more prolonged effect on the time.     

Cytobiocompatibility of collagen and ePTFE membranes on osteoblast-like cells in vitro

In guided bone regeneration (GBR), a semipermeable membrane is placed over an osseous defect to create a secluded environment in which bone formation can proceed without ingrowth of connective tissue cells from the overlaying soft tissue. Although the cell-occlusive property of GBR membranes appear to be essential to new bone formation, the role of transmembrane tissue fluid diffusion is not known. The objective of this study was to evaluate the degree to which diffusion across commonly used GBR membranes can support functional properties of osteoblast-like cells in vitro. Cells from an established osteoblast-like line (SAOS-2) were cultured on membranes of cross-linked collagen, noncross linked collagen, and ePTFE. The membranes rested on metal grids which allowed the membranes to lightly contact the surface of the culture medium. As a control, cells were directly plated and cultured in control wells. At days 7 and 21, cells were harvested by scraping the membranes or culture wells and analyzed for expression of alkaline phosphatase (ALP), core binding factor 1 (cbfa-1), bone sialoprotein-2 (BSP-2), and osteocalcin (OC). Expression was determined by quantitative real-time PCR. Glucose-6-phosphate dehydrogenase (G6PD) served as a reference gene. The membranes were examined by transmission light microscopy. RT-PCR revealed up-regulation of ALP of up to 60-fold and of cbfa-1 and BSP of up to threefold relative to G6PDH. Expression of OC was less then onefold. The expression profile for each of the four genes tested demonstrated small variations among cells grown on different membranes. Microscopic observations revealed remnants of undisrupted osteoblast-like cells attached to both collagen membranes. Cell morphology and spatial arrangement indicated that vitality was maintained. Diffusion through the three membranes evaluated in this study was sufficient to support osteoblast-like cell differentiation.     

In vitro behavior of neural stem cells in response to different chemical functional groups

Neural stem cells (NSCs) cultured on glass surfaces modified by different chemical groups, including hydroxyl (–OH), sulfonic (–SO₃H), amino (–NH₂), carboxyl (–COOH), mercapto (–SH) and methyl (–CH₃) groups, are shown here to commit to phonotypes with extreme sensitivity to surface chemical groups. The adhering NSCs at the level of single cells exhibited morphological changes in response to different chemical groups. NSCs on –SO₃H surfaces had the largest contact area and the most flattened morphology, while those on –CH₃ surfaces exhibited the smallest contact area and the most rounded morphology. After 5 days of culture, the migration of NSCs from their original aggregates onto these test surfaces followed the trend: –NH₂>–COOH = –SH?–SO₃H>–CH₃>–OH. The expression of specific markers, including nestin, β-Tubulin-III, glial fibrillary acidic protein and O4, were used to examine NSCs lineage specification. The –SO₃H surfaces favored NSCs differentiation into oligodendrocytes, while NSCs in contact with –COOH, –NH₂, –SH and –CH₃ had the ability to differentiate into neurons, astrocytes and oligodendrocytes. Compared to –COOH surfaces, –NH₂ seemed to promote neuronal differentiation. These chemically modified surfaces exhibited regulation of NSCs on adhesion, migration and differentiation potential, providing chemical means for the design of biomaterials to direct NSCs lineage specification for neural tissue engineering.     

The effect of zoledronate-hydroxyapatite nanocomposites on osteoclasts and osteoblast-like cells in vitro

This study demonstrates that zoledronate containing hydroxyapatite nanocrystals (HA-ZOL) can be synthesized as a single crystalline phase up to a zoledronate content of about 7 wt% by direct synthesis in aqueous solution, at variance with what previously found for alendronate-hydroxyapatite nanocrystals (HA-AL). On increasing zoledronate incorporation, the length of the coherent crystalline domains and the crystal dimensions of hydroxyapatite decrease, whereas the specific surface area increases. Full profile fitting of the powder X-ray diffraction patterns does not indicate major structural modifications, but an increase of the hydroxyapatite unit cell, on increasing zoledronate content. These data, together with a structural similarity between hydroxyapatite and calcium zoledronate, suggest a preferential interaction between zoledronate and the hydroxyapatite faces parallel to the c-axis direction. Osteoblast-like MG-63 cells and human osteoclasts were cultured on HA-ZOL nanocrystals and as a comparison on HA-AL nanocrystals containing almost the same (about 7 wt%) bisphosphonate amount. The beneficial influence of bisphosphonates on osteoblast proliferation and differentiation is enhanced when the tests are performed in co-cultures. Similarly, the reduction of osteoclast proliferation and the increase of Caspase 3 production are dramatically enhanced in co-cultures, which highlight an even greater influence of HA-ZOL than HA-AL on osteoclast apoptosis.     

Intermittent versus continuous stretching effects on osteoblast-like cells in vitro

The objective of this study was to quantify and compare stretch-mediated responses of primary rat osteoblast-like cells to uniform cyclic strain applied intermittently or continuously. Primary rat osteoblast-like cells were seeded and cultured in silicone rubber dishes for 2 days. They were then subjected to 1000 microstrains at 1 Hz for periods of 60 consecutive minutes or to a series of 15-min stretch followed by 15-min rest, until a total stretch of 60 min. After stretching, cells were incubated and assayed on days 4, 8, 16, and 24 for DNA content, alkaline phosphatase (ALP) activity, and calcium (Ca) content. Additionally, qualitative information was obtained via scanning electron and confocal laser scanning micrographs. Significant increases in DNA were observed for cells stretched intermittently versus cells stretched continuously and versus controls. Results showed significant decreases (p < 0.05) in ALP for cells between stretched groups and between both stretched groups versus controls. Additionally, Ca content was greater in cells stretched intermittently versus controls on days 4 and 8 and versus cells stretched continuously on day 24. In conclusion, intermittently strained cells demonstrated significant decreases in ALP and increases in DNA and Ca versus cells strained continuously. This supports the theory that cells respond to mechanical loading in a "trigger-like" response.     

Influence of titanium surfaces on attachment of osteoblast-like cells in vitro

Implant surface topography influences osteoblastic proliferation, differentiation and extracellular matrix protein expressions. Studies on preliminary interactions of osteoblast-like cells on implant interface through in vitro systems, can give lucid insights to osseo-integrative efficacies of when in vivo implants. In the present investigation two titanium surfaces of dental implants, a sandblasted and acid-etched surface and an experimental grooved surface were compared through in vitro systems. The titanium implants were seeded with osteoblast-like primary cells and maintained for a period of 1-7 days. Expressions of fibronectin and osteonectin were assessed through immunogold labelling by scanning electron microscopy. The grooved surface, supported better osteoblastic cell adhesion and proliferation than the rough surfaces. Further, osteoblastic cells on the grooved surfaces also displayed a strong labelling for fibronectin at the cytoplasmic extensions coupled with intense osteonectin expression in comparison to the rough surfaced implants. In conclusion, grooved surfaces offered better cell attachment and proliferation than the other rough surfaces studied.     

In vitro fibroblast response to polyurethane organosilicate nanocomposites

The term nanocomposite refers to organic:inorganic composites where one phase, typically the inorganic phase, has dimensions on the nanoscale. Several authors have noted the potential benefit of biomedical application of nanocomposite technology, and have suggested using quaternary ammonium compounds (QAC) as an organic modification to enhance dispersion of nanoparticles within polymer matrices. This study aimed to examine fibroblast responses in vitro to a range of nanocomposites using different organic modifiers. Composite materials were prepared from a polyether urethane (PEU) and various unmodified and organically modified montmorillonite (MMT) nanoparticles. QAC and amino undecanoic acid (AUA) modified-MMT were added to PEU at loadings ranging from approximately 1 to 15 wt %. Composites with organically modified QAC and AUA particles displayed partially exfoliated and intercalated silicate morphology, respectively. Nanocomposites showed increases in ultimate tensile properties for materials with lower QACMMT loadings. However QAC was shown to significantly inhibit cell growth following release from PEU-QACMMT under extraction conditions mimicking those of the physiological environment. Materials containing silicate modified using AUA were cytocompatible. The results of this study suggest that QAC may be unsuitable as organic modifiers for nanoparticles destined for biomedical use. Alternative modifiers based on AUA confer equivalent dispersion and are of low toxicity.     

Morphological behavior of osteoblast-like cells on surface-modified titanium in vitro.

In recent papers, we reported the results of a study on the graded porous titanium coatings on titanium by plasma spraying and amino-group ion implantation. The paper is to preliminarily evaluate the biocompatibility of surface-modified titanium through 2, 5 and 7 days cell culture in vitro. Cell morphology was observed by a scanning electron microscope. Cell proliferation and type I collagen synthesis were measured by 3(4.5-dimethyl-thiazole-2-yl)2,5-diphenyl tetrazolium bromide (MTT) and enzyme-linked immunosorbent assay (ELISA), respectively. Our experimental results showed that osteoblast-like cells attached and spread well on surface-modified titanium. Cells were observed to grow into the pores and form extracellular matrix. MTT and ELISA results showed no detrimental effect on the development of cell. These studies support the biocompatibility of surface-modified titanium.     

Stretch-mediated responses of osteoblast-like cells cultured on titanium-coated substrates in vitro

Cyclic stretching experiments on osteoblast-like cells have proven to be a useful tool in understanding the underlying mechanisms of load transduction at the bone-implant surface. However, most experimental setups use silicone rubber substrates, which are atypical for orthopedic and dental implant materials. Therefore, we investigated the responses of osteoblast-like cells to loading on titanium (Ti)-coated versus plain silicone substrates. Ti-coated substrates were made by a radio-frequency magnetron sputtering process, and characterized using Rutherford backscattering spectrometry, X-ray photoelectron spectroscopy, and contact-angle measurements. Osteoblast-like cells cultured from rat bone marrow were seeded on both types of substrates and stretched for 1 h continuously. Subsequently, cell proliferation, alkaline phosphatase activity, and calcium content were measured for up to 24 days after seeding. In addition light-, scanning electron-, and confocal laser scanning micrographs were made. The results showed that our Ti coating had a thickness of 50 nm and contained Ti/oxygen as 1:1. However, further characterization proved that the silicone material had a tendency to resurface through the coating. Osteoblast-like cells proliferated faster on the Ti-coated substrates, but differentiation was slower compared with the silicone substrates. It was concluded that that there was a definitive influence of the substrate material in mechanical stress models. Therefore, extrapolation of results obtained using silicone substrates cannot be translated directly toward the situation of metallic implant materials.     

The response of osteoblast-like cells towards collagen type I coating immobilized by p-nitrophenylchloroformate to titanium

The scaffold surface composition can be altered by the use of surface coatings. The use of thin coatings will give special surface properties, while the bulk properties of the scaffold are preserved. Collagen type I is known to play an important role during cell adhesion as well as osteoblast differentiation. A common way to coat surfaces is the adsorption method. An alternative way is the use of a protein immobilization method like p-nitrophenyl chloroformate. In this study, we investigated the effect of a collagen type I coating and p-nitrophenyl chloroformate as a protein immobilization method on osteoblast adhesion, proliferation, and differentiation. Titanium fiber meshes were treated with sodium hydroxide (NaOH), followed by p-nitrophenyl chloroformate, and coated with collagen type I. Osteoblast-like cells were seeded into the meshes and cultured for 24 days. The cell attachment, proliferation, and differentiation were measured by using Live and Dead assay, cell counting, DNA analysis, alkaline phosphatase activity assay, calcium content measurement, Real Time PCR (QPCR), and scanning electron microscopy (SEM). Results demonstrated that initially less cells were attached to the covalently bounded collagen meshes (NPC-Col) compared with titanium as control (Ti) and adsorbed collagen meshes (ABS-Col). Further, a decreased growth curve of cells cultured on the NPC-Col meshes was observed in comparison with Ti and ABS-Col meshes. The calcium measurements and SEM pictures revealed that all three surfaces showed differentiation of osteoblast-like cells after 8-24 days. On the basis of our results, we conclude that initially less cells were attached to the NPC-Col meshes and that they had a decreased proliferation rate. Further, we conclude that an adsorbed collagen type I coating stimulated the osteoblastic differentiation of rat bone marrow cells.     

Microrough titanium surface affects biologic response in MG63 osteoblast-like cells

The purpose of this study was to define the surface properties of prepared titanium (Ti) disks, which served as a model system, and to contrast the biologic response of MG63 cells exposed to Ti disks with different levels of surface roughness. The surface properties interact with each other, resulting in a change of other surface qualities in addition to roughness due to the surface roughening procedure. The machined Ti disks were roughened by sandblasting and electric glow discharging. The surface properties of the Ti specimens were inspected through a comprehensive surface analysis. MG63 cell behaviors were compared along with cell number, alkaline phosphatase (ALP) activity, Runx2 gene expression, and type I collagen production. Statistics were evaluated, using analysis of variance (ANOVA). The sandblasted Ti disks demonstrated well-controlled surface roughness features and meaningful average roughness ranges, including the surface roughness of the "modern" microrough implant, used clinically. With increasing Ti surface roughness, the cell number decreased, while the ALP activity, type I collagen production, and Runx2 gene expression increased significantly. The rougher the Ti surface was, the sooner the Runx2 gene was expressed. Based on these results, we suggest that the microrough Ti surfaces of the 1-3 mum range may contribute effectively to osteogenic differentiation and proliferation in MG63 cells.