Pullout strength of tibial graft fixation in anterior cruciate ligament replacement with a patellar tendon graft: interference screw versus staple fixation in human knees

The endoscopic single incision technique for anterior cruciate ligament (ACL) reconstruction with a femoral half-tunnel may lead to a graft/tunnel mismatch and subsequent protrusion of the block from the tibial tunnel. The typical tibial fixation with an interference screw is not possible in these cases. Fixation with staples in a bony groove inferior to the tunnel outlet can be used as an alternative technique. Current literature does not provide biomechanical data of either fixation technique in a human model. This study was performed to evaluate the primary biomechanical parameters of this technique compared with a standard interference screw fixation of the block. Fifty-five fresh-frozen relatively young (mean age 44 years) human cadaver knee joints were used. Grafts were harvested from the patellar tendon midportion with bone blocks of 25 mm length and 9 mm width. A 10-mm tibial tunnel was drilled from the anteromedial cortex to the center of the tibial insertion of the ACL. Three different sizes of interference screws (7 × 30, 9 × 20, 9 × 30 mm) were chosen as a standard control procedure (n = 40). For tibial bone-block fixation the graft was placed through the tunnel, and the screw was then inserted on the cancellous or the cortical surface, respectively. Fifteen knees were treated by staple fixation. A groove was created inferior to the tunnel outlet with a chisel. The bone block was fixed in this groove with two barbed stainless steel staples. Tensile testing in both groups was carried out under an axial load parallel to the tibial tunnel in a Zwick testing machine with a velocity of 1 mm/s. Dislocation of the graft and stiffness were calculated at 175 N load. Maximum load to failure using interference screws varied between 506 and 758 N. Load to failure using staples was 588 N. Dislocation of the graft ranged between 3.8 and 4.7 mm for interference screw fixation and was 4.7 mm for staples. Stiffness calculated at 175 N load was significantly higher in staple fixation. With either fixation technique, the recorded failure loads were sufficient to withstand the graft loads which are to be expected during the rehabilitation period. Staple fixation of the bone block outside of the tunnel resulted in a fixation strength comparable to interference screw fixation. Received: 2 September 1996 Accepted: 30 January 1997     

The influence of screw geometry on hamstring tendon interference fit fixation

We used a standardized model of calf tibial bone to investigate the influence of screw diameter and length on interference fit fixation of a three-stranded semitendinosus tendon graft for anterior cruciate ligament reconstruction. Biodegradable poly-(L-lactide) interference screws with a diameter of 7, 8, and 9 mm and a length of 23 and 28 mm were used. We examined results in three groups of 10 specimens each: group 1, screw diameter equaled graft diameter and screw length was 23 mm; group 2, screw diameter equaled graft diameter plus 1 mm and screw length was 23 mm; group 3, screw diameter equaled graft diameter and screw length was 28 mm. The mean pull-out forces in groups 1, 2, and 3 were 367.2+/-78 N, 479.1+/-111.1 N, and 537.4+/-139.1 N, respectively. The force data from groups 2 and 3 were significantly higher than those from group 1. These results indicate that screw geometry has a significant influence on hamstring tendon interference fit fixation. Increasing screw length improves fixation strength more than oversizing the screw diameter. This is important, especially for increasing tibial fixation strength because the tibial graft fixation site has been considered to be the weak link of such a reconstruction.     

Cyclic pull-out strength of hamstring tendon graft fixation with soft tissue interference screws. Influence of screw length

Blunt-threaded interference screws used for fixation of hamstring tendons in anterior cruciate ligament reconstructions provide aperture fixation and may provide a biomechanically more stable graft than a graft fixed further from the articular surface. It is unknown if soft tissue fixation strength using interference screws is affected by screw length. We compared the cyclic and time-zero pull-out forces of 7 x 25 mm and 7 x 40 mm blunt-threaded metal interference screws for hamstring graft tibial fixation in eight paired human cadaveric specimens. A four-stranded autologous hamstring tendon graft was secured by a blunt-threaded interference screw into a proximal tibial tunnel with a diameter corresponding to the graft width. Eight grafts were secured with a 25-mm length screw while the other eight paired grafts were secured with a 40-mm length screw. During cyclic testing, slippage of the graft occurred as the force of pull became greater with each cycle until the graft-screw complex ultimately failed. All grafts failed at the fixation site, with the tendon being pulled past the screw. There were no measurable differences in the mean cyclic failure strength, pull-out strength, or stiffness between the two sizes of screws. Although use of the longer screw would make removal technically easier should revision surgery be necessary, it did not provide stronger fixation strength than the shorter, standard screw as had been postulated.     

Effect of screw length on bioabsorbable interference screw fixation in a tibial bone tunnel

Initial tibial fixation strength is the weak link after anterior cruciate ligament reconstruction with a quadrupled hamstring tendon graft fixed with bioabsorbable interference screws. The purpose of this study was to determine the biomechanical differences between 28-mm and tapered 35-mm interference screws for tibial fixation of a soft tissue graft in 16 young cadaveric tibias. Failure mode, displacement before failure, and ultimate failure load were tested with a testing machine aligned with the tibial tunnel to simulate a worst-case scenario. The mode of failure was graft slippage past the screw in all but one of the specimens. The mean maximum load at failure of the 28-mm screw was 594.9 +/- 141.0 N, with mean displacement at failure of 10.97 +/- 2.20 mm. The mean maximum load at failure of the 35-mm screw was 824.9 +/- 124.3 N, with a mean displacement to failure of 14.38 +/- 2.15 mm. The 38% difference in mean maximal load at failure was significant. Important variables in hamstring tendon graft fixation within a bone tunnel include bone mineral density, dilatation, gap size, screw placement, and screw width and length. Attention to these variables will help to provide secure graft fixation during biologic incorporation throughout the rehabilitation period.     

Analysis of initial fixation strength of press-fit fixation technique in anterior cruciate ligament reconstruction

We performed a controlled laboratory study to evaluate the initial fixation strength of press-fit technique. Forty porcine lower limbs were used and divided into four groups according to the method of fixation; group 1 (press-fit+1.4 mm), in which the diameter difference between the bone plug and the femoral tunnel was 1.4 mm; group 2 (press-fit+1.4 mm, 30 degrees), in which the diameter difference was the same with group 1, but the tensile loading axis was 30 degrees away from the long axis of the femoral tunnel; group 3 (titanium), in which a titanium interference screw was used for fixation; group 4 (bioabsorbable), in which a bioabsorbable interference screw was used for fixation. The graft in the press-fit group was harvested with a hollow oscillating saw with inner diameter of 9.4 mm to obtain consistent and completely circular shape of the bone plug. The femoral tunnel with diameter of 8 mm was drilled at the original ACL insertion. Following the bone plug insertion into the femoral tunnel and applying a preload of 20 N, the specimen underwent 500 loading cycles between 0 and 2 mm of displacement. Thereafter the specimen was loaded to failure. There was no fixation site failure during the cyclic loading test. Significant differences in the stiffness, linear load, or failure mode among the groups were not found. The average ultimate failure load of group 1 and group 2 were not significantly different from those of group 3 and group 4. The press-fit groups demonstrated sufficient fixation strength for the rehabilitation and interference screw groups. The completely circular shape of the bone plug and increased diameter difference between the bone plug and the femoral tunnel seemed to contribute to the strong fixation.     

A biomechanical evaluation of transcondylar femoral fixation of anterior cruciate ligament grafts

BACKGROUND: Interference screw fixation of the graft in anterior cruciate ligament reconstruction is considered the gold standard, but limited clinical experience suggests that transcondylar fixation is equally effective. PURPOSE: To compare transcondylar and interference screw fixation. STUDY DESIGN: Ex vivo biomechanical study. METHODS: Twenty pairs of unembalmed knees underwent anterior cruciate ligament reconstruction with patellar tendon autografts. In 1 knee of each pair, the bone plug was stabilized in the femoral tunnel with standard interference screws; in the other knee, transcondylar screws were used. Testing to failure occurred immediately or after 1000 cycles of sinusoidal loading (30 to 150 N) (20 paired reconstructions each). Fixation stiffness, strength, graft creep, displacement amplitude, and change in amplitude were measured and compared (repeated measures anaylsis of variance with Tukey test; P <.05). RESULTS: There was no significant difference in acute strength, maximum load within 3 mm, or stiffness between transcondylar fixation (410 +/- 164 N, 183 +/- 93 N, and 49.6 +/- 28 N/mm, respectively) and interference fixation (497 +/- 216 N, 206 +/- 115 N, and 61 +/- 37.8 N/mm, respectively). Similarly, there was no significant difference in cyclic strength, maximum load within 3 mm, or stiffness between transcondylar fixation (496 +/- 214 N, 357 +/- 82.9 N, and 110 +/- 27.4 N/mm, respectively) and interference fixation (552 +/- 233 N, 357 +/- 76.2 N, and 112 +/- 26.8 N/mm, respectively). Predominant modes of failure were bone plug pullout (transcondylar fixation) and tendon failure or bone plug fracture (interference fixation). CONCLUSIONS: Transcondylar screw fixation of the patellar tendon autograft into the femoral tunnel performed mechanically as well as interference screw fixation. CLINICAL RELEVANCE: The results suggest that transcondylar and interference screws provide similar fixation for anterior cruciate ligament reconstruction.     

The influence of tendon length and fit on the strength of a tendon-bone tunnel complex. A biomechanical and histologic study in the dog

Using a dog model, we examined the influence of tendon length and fit within a bone tunnel on the pull-out strength of a tendon-bone tunnel complex at 6 weeks after fixation. Fourteen adult mongrel dogs (weight, 25 to 30 kg) underwent bilateral hindlimb surgery in which the extensor digitorum longus tendon was transplanted into an extraarticular metaphyseal bone tunnel. Our findings demonstrated that pull-out strength at 6 weeks was enhanced by increasing the length of tendon within the tunnel. The average load to failure with 1 cm of tendon within the tunnel was 153.7 +/- 78.6 N, compared with 265.5 +/- 93.3 N for the specimens with 2 cm of tendon in the tunnel. Tendon fit within the tunnel was also found to be important. The average load to failure when a tendon was placed in a 4.2-mm diameter tunnel was 301 +/- 61 N at 6 weeks. The average load to failure when the tendon was placed within a 6-mm diameter tunnel was 228 +/- 65 N. These differences were statistically different. Histologically, the interface between the tendon and bone appeared to be most mature when there was intimate bone-to-tendon contact. These data suggest that maximizing tendon length within a bone tunnel and minimizing tendon-tunnel diameter mismatch will maximize the strength of a tendon-bone tunnel complex at 6 weeks.     

Tibial bone bridge and bone block fixation in double-bundle anterior cruciate ligament reconstruction without hardware: a technical note

Current techniques for tibial graft fixation in four tunnels double bundle (DB) anterior cruciate ligament (ACL) reconstruction are by means of two interference screws or by extracortical fixation with a variety of different implants. We introduce a new alternative tibial graft fixation technique for four tunnels DB ACL reconstruction without hardware. About 3.5 to 5.5 cm bone cylinder with a diameter of 7 mm is harvested from the anteromedial (and posterolateral) tibial bone tunnel (s) with a core reamer. The anteromedial (AM) and posterolateral (PL) hamstring tendon grafts (or alternatively tendon allografts) are looped over an extracortical femoral fixation device and cut in length according to the total femorotibial bone tunnel length. The distal 3 cm of each, the AM- and PL bundle graft are armed with two strong No. 2 nonresorbable sutures and the four suture ends of each graft are tied to each other over the 2 cm wide cortical bone bridge between the tibial AM and PL bone tunnel. In addition the AM- and/or PL bone block which was harvested at the beginning of the procedure is re-impacted into the two tibial bone tunnels. A dorsal splint is used for the first two postoperative weeks and physiotherapy is started the second postoperative day. The technique is applicable for four tunnels DB ACL reconstruction in patients with good tibial bone quality. The strong fixation technique preserves important tibial bone stock and avoids the use of tibial hardware which knows disadvantages. It does increase tendon to bone contact and tendon-to-bone healing and does reduce implant costs to those of a single bundle (SB) ACL reconstruction. Revision surgery may be facilitated significantly but the technique should not be used when bony defects are present. In case of insufficient bone bridge fixation or bone blocks hardware fixation can be applied as usual. Not supported by outside funding or grant(s): No benefits in any form have been received, or will be received, from a commercial party related directly or indirectly to the subject of this article. The study complies with the current laws of the country, in which it was performed.     

Biomechanical evaluation of a new cross-pin technique for the fixation of different sized bone–patellar tendon–bone grafts

To overcome the disadvantages of interference-screw fixation of bone–patellar tendon–bone (BPTB) grafts, new fixation techniques for anterior cruciate ligament (ACL) grafts using biodegradable pins have been developed. The hypothesis of the present study was that cross-pin fixation techniques provide a primary stability that is comparable to that of interference screws. A biomechanical in vitro study was discussed. Human BPTB grafts of 8, 9 and 10 mm diameter were fixed in bovine knees with biodegradable cross pins (diameter: 2.0, 2.7 or 3.2 mm) or biodegradable interference screws. Stiffness and ultimate load were evaluated. For 9 and 10 mm BPTB grafts, no statistically significant difference in maximum load and stiffness was found between the four fixation techniques tested. For 8 mm bone blocks the maximum load of the 3.2 mm pins (274.2 N) was significantly lower than for the 2.0 mm pins (479.8 N) and the interference screws (504.0 N). Predominant failure mode in this group was bone-block fracture. Thicker grafts (9 and 10 mm) fixed with the 2.0 mm pins predominantly failed by implant fracture. Femoral fixation of 8, 9 and 10 mm BPTB grafts using cross pins leads to biomechanical properties that are comparable to biodegradable interference screws when tested by a single-cycle load to failure. Cross pins provide a rigid fixation for 9 and 10 mm BPTB grafts.     

Optimal screw diameter for interference fixation in a bone tunnel: a porcine model

The study investigates the optimal interference screw dimensions required to secure a tendon graft in a bone tunnel. A standard 8 mm pig flexor-tendon graft was inserted into a standard open-ended 8 mm bone tunnel of a porcine distal femur and secured using either 7 mm, 8 mm or 9 mm diameter metal interference screws (Arthrex Inc, Naples, FL). The construct was tested to failure using a Shimadzu ASG 10KN Universal Material Testing Machine (Shimadzu, Tokyo, Japan). Load and mode of construct failure were recorded for 37 individual constructs. There was no significant difference in the load at failure between the 7 mm screw (192 N; range 151–232) and 8 mm screw (181 N; range 150–212) (p>0.05). There was a significant difference between the 7 mm screw and the 9 mm screw (109 N; range 67–151) (p=0.006) and between the 8 mm screw and the 9 mm screw (p=0.015). When using a 9 mm screw, 100% of the constructs failed by cut out of the graft at the tunnel opening. The 7 mm constructs failed by slippage of the tendon from the bone tunnel in 83% of cases, with only 17% failing by cut out at the tunnel opening. The 8 mm constructs demonstrated a mixture of failure modes, with slippage occurring in 58% of cases, cut out in 38% and failure of the graft substance in one case (4%). In this model, screw diameters equal to or 1 mm less than the tunnel/tendon diameter provides better fixation than using a screw 1 mm larger. The mode of failure differs for each of these screws.     

Femoral fixation of hamstring grafts in posterior cruciate ligament reconstruction: biomechanical evaluation of different fixation techniques: is there an acute angle effect?

BACKGROUND: The literature provides little biomechanical data about femoral fixation of hamstring grafts in posterior cruciate ligament reconstruction. HYPOTHESIS: A hybrid fixation technique with use of an undersized screw has sufficient strength to provide secure fixation of posterior cruciate ligament grafts. Additional aperture fixation with a biodegradable interference screw can prevent graft damage that might be caused by an acute angle on the edge of the femoral tunnel. STUDY DESIGN: Controlled laboratory study. METHODS: In part 1, extracortical fixation of posterior cruciate ligament reconstructions with quadrupled porcine flexor digitorum grafts to simulate human hamstring grafts was compared with hybrid fixation methods using 6-, 7-, and 8-mm screws. Groups were tested in cycling loading with the load applied in line with the bone tunnel. In part 2, extracortical fixation was compared with hybrid fixation using a 1-mm undersized screw anterior and posterior to the graft. Structural properties and graft abrasion were evaluated after cyclic loading with the load applied at 90 degrees to the tunnel. In each group, 8 porcine knees were tested. RESULTS: In part 1, stiffness, maximum load, and yield load were significantly higher for hybrid fixation than for extracortical fixation. Hybrid fixation with an 8-mm screw resulted in higher yield load than with a 7-mm screw. In part 2, graft laceration was more pronounced in specimens with extracortical fixation than with hybrid fixation. Posterior screw placement was superior to the anterior position. CONCLUSION: For all parameters, hybrid fixation with an interference screw provided superior structural results. No relevant disadvantages of undersized screws could be found. Graft damage due to abrasion at the edge of the femoral bone tunnel was reduced by use of an interference screw. The posterior screw placement seems favorable. CLINICAL RELEVANCE: Hybrid fixation of hamstring grafts in posterior cruciate ligament reconstruction is superior to extracortical fixation alone with no relevant disadvantages of undersized screws. The results raise the suspicion of an acute angle effect of the femoral bone tunnel.     

Close-looped graft suturing improves mechanical properties of interference screw fixation in ACL reconstruction

Purpose

In anterior cruciate ligament reconstruction with looped soft-tissue grafts, an interference screw is frequently used for tibial fixation. This study compared three alternatives thought to improve the initial mechanical properties of direct bioabsorbable interference screw fixation: suturing the graft to close the loop, adding a supplementary staple, or increasing the oversize of the screw diameter relative to the bone tunnel from 1 to 2 mm.

Methods

Twenty-eight porcine tibiae and porcine flexor digitorum profundus tendons were randomized into four testing groups: a base fixation using 10-mm-diameter screw with open-looped graft, base fixation supplemented by an extracortical staple, base fixation but closing the looped graft by suturing its ends, and base fixation but using an 11-mm screw. Graft and bone tunnel diameters were 9 mm in all specimens. Constructs were subjected to cyclic tensile load and finally pulled to failure to determine their structural properties.

Results

The main mode of failure in all groups was pull-out of tendon strands after slippage past the screw. The sutured graft group displayed significantly lower residual displacement (mean value reduction: 47–67 %) and higher yield load (mean value increase: 38–54 %) than any alternative tested. No other statistical differences were found.

Conclusions

Suturing a soft-tissue graft to form a closed loop enhanced the initial mechanical properties of tibial fixation with a bioabsorbable interference screw in anterior cruciate ligament reconstructions using a porcine model, and thus, this may be an efficient means to help in reducing post-operative laxity and early clinical failure. No mechanical improvement was observed for an open-looped tendon graft by adding an extracortical staple to supplement the screw fixation or by increasing the oversize of the screw to tunnel diameter from 1 to 2 mm.     

Biomechanical properties of patellar and hamstring graft tibial fixation techniques in anterior cruciate ligament reconstruction: experimental study with roentgen stereometric analysis

BACKGROUND: Reliable fixation of the soft hamstring grafts in ACL reconstruction has been reported as problematic. HYPOTHESIS: The biomechanical properties of patellar tendon (PT) grafts fixed with biodegradable screws (PTBS) are superior compared to quadrupled hamstring grafts fixed with BioScrew (HBS) or Suture-Disc fixation (HSD). STUDY DESIGN: Controlled laboratory study with roentgen stereometric analysis (RSA). METHODS: Ten porcine specimens were prepared for each group. In the PT group, the bone plugs were fixed with a 7 x 25 mm BioScrew. In the hamstring group, four-stranded tendon grafts were anchored within a tibial tunnel of 8 mm diameter either with a 7 x 25 mm BioScrew or eight polyester sutures knotted over a Suture-Disc. The grafts were loaded stepwise, and micromotion of the graft inside the tibial tunnel was measured with RSA. RESULTS: Hamstring grafts failed at lower loads (HBS: 536 N, HSD 445 N) than the PTBS grafts (658 N). Stiffness in the PTBS group was much greater compared to the hamstring groups (3500 N/mm versus HBS = 517 N/mm and HSD = 111 N/mm). Irreversible graft motion after graft loading with 200 N was measured at 0.03 mm (PTBS), 0.38mm (HBS), and 1.85mm (HSD). Elasticity for the HSD fixation was measured at 0.67 mm at 100 N and 1.32 mm at 200 N load. CONCLUSION: Hamstring graft fixation with BioScrew and Suture-Disc displayed less stiffness and early graft motion compared to PTBS fixation. Screw fixation of tendon grafts is superior to Suture-Disc fixation with linkage material since it offers greater stiffness and less graft motion inside the tibial tunnel. Clinical Relevance: Our results revealed graft motion for hamstring fixation with screw or linkage material at loads that occur during rehabilitation. This, in turn, may lead to graft laxity.     

A prospective evaluation of tunnel enlargement in anterior cruciate ligament reconstruction with hamstrings: extracortical versus anatomical fixation

Changes in the femoral and tibial bone tunnel were studied prospectively after arthroscopic ACL reconstruction with quadruple hamstring autograft. To determine whether tunnel enlargement can be decreased by fixing the graft close to the joint line having a stiffer fixation construct we compared "anatomical" (one absorbable interference screw femorally, and bicortical fixation with two absorbable interference screws tibially) and extracortical fixation techniques (Endobutton femorally, and two no. 6 Ethibond sutures over a suture washer tibially). Over a 2-year period we evaluated 60 patients clinically (IKDC scale, Cincinnati Knee Score, KT-1000) and radiographically (confirmed by MRI). The operated knee was radiographed immediately postoperatively and 6 and 24 months postoperatively. The femoral and tibial bone tunnel diameter was measured on anteroposterior and lateral images, and the tunnel area was calculated and compared to the initial area calculated from the perioperative drill size. In the "anatomical" group the immediately postoperative bone tunnel area was 75% larger than the initial tunnel area, after 6 months it was increased another 31%, and between 6 and 24 months it remained basically unchanged. In the "extracortical" group there was no significant enlargement immediately postoperatively, but after 6 months it was 65% larger than the initial area of drill and graft size, and between 6 and 24 months it decreased to 47%. There was no correlation between the amount of tunnel enlargement and clinical scores or KT-1000 measurement. Arthroscopic ACL reconstruction with quadruple hamstring autograft is associated with bone tunnel enlargement. Using a purely extracortical fixation technique thus significantly increased the tibial and femoral tunnel area during the first 6 postoperative months, while it decreased slightly thereafter. The insertion of large interference screws apparently not only compresses the graft in the bone tunnel but also significantly enlarges the bone tunnel itself. The immediate enlargement at the time of the operation is followed by a reduced further enlargement at 6 months and then stabilization. Tunnel widening did not influence clinical outcome over a 2-year period.     

Interactive effects of tunnel dilation on the mechanical properties of hamstring grafts fixed in the tibia with interference screws

The effect of dilation of the tibial tunnel on the strength of hamstring graft fixation using interference screws was evaluated. In all, 28 RCI screws were tested in male human tibia-hamstring constructs with tibial tunnels reamed or dilated to the respective size of the graft diameter. Dilation of the tibial tunnel failed to significantly enhance hamstring fixation. Grafts secured in dilated tunnels displayed an 11% greater resistance to the initiation of graft slippage (174+/-112 N) compared to their undilated controls (156+/-77 N, P=0.63). Dilation of the tibial tunnel increased the failure load by an average of 4%, independent of screw diameter (dilated specimens: 360+/-120 N, controls: 345+/-88 N, P=0.74). Biomechanical research on the effect of tibial tunnel dilation in hamstring fixation has not provided satisfactory evidence as to the benefits of this additional surgical step during anterior cruciate ligament (ACL) reconstruction.     

Initial fixation strength of two bioabsorbable pins for the fixation of hamstring grafts compared to interference screw fixation: single cycle and cyclic loading

BACKGROUND: During the early postoperative period, the fixation of a hamstring graft to the bone tunnel is the primary factor in limiting rehabilitation. HYPOTHESIS: The initial fixation strength of a double cross pin fixation technique is comparable with the biodegradable interference screw fixation technique. STUDY DESIGN: Experimental laboratory study. METHODS: The authors examined the initial fixation strength of two 3.3-mm bioabsorbable pins compared to interference screws for hamstring grafts in bovine knees. RESULTS: Analysis of yield load, maximum load, and stiffness in the single-cycle loading test showed no statistically significant differences for cross pin and interference fixation (P <.05). For cross pins and interference screws, the mean displacement under 1000 cycles to 250 N was 5.07 ( +/- 1.9) mm and 4.81 ( +/- 2.5) mm, stiffness 252 ( +/- 78) N/mm and 289 ( +/- 148) N/mm. Only grafts fixed with cross pins survived 1000 cycles to 450 N. CONCLUSION: The initial fixation strength of the double cross pin technique is comparable to that of interference screw fixation with a stiffness comparable to that of the native ACL. Clinical Relevance: Hamstring graft fixation using two cross pins provides an alternative to bioabsorbable interference screw fixation.     

Comparison of torsional strengths of bioabsorbable screws for anterior cruciate ligament reconstruction

The goals of this study were to evaluate torsional strength and modes of failure in commercially available bioabsorbable interference screws and to test the effect of screw diameter on torsional strength when screws become jammed during insertion. We tested the Arthrex, BioScrew, Endo-Fix, Phantom, and Sysorb screws, all 20 mm in length. Four major modes of failure were encountered. Analysis of variance revealed that both screw type and diameter had a significant effect on failure torque. The Endo-Fix 7-mm screw had the lowest failure torque (1.07 +/- 0.18 N x m) and the Sysorb 8-mm screw had the highest (5.23 +/- 0.24 N x m). The Sysorb was significantly stronger than all the other screws. The failure torques were within the range that has been reported for manual screw insertion. We concluded that technical factors, which can affect insertion torque, assume particular importance with the use of bioabsorbable interference screws.     

Biceps tenodesis with interference screw: cyclic testing of different techniques

Different surgical techniques exist for biceps tenodesis. The most secure fixation technique is with interference screws. The purpose of the study was to compare the biomechanical performance of three different interference screw biceps tenodesis fixation methods, which involve different tunnel preparation methods. Using a sheep shoulder model and metal interference screws, a bone wedge technique was compared to serial tunnel dilation and a control group. After a preload, all repairs were cyclically loaded (20–60 N) for 100 cycles followed by destructive testing. Biceps tenodesis using an interference screw—bone wedge technique showed statistically lower cyclic displacement (8.1 ± 6.4 mm) than serial dilatation with an interference screw (21.3 ± 8.4 mm) or interference screw fixation alone (18.3 ± 8.3 mm) (P = 0.02). There were no statistically significant differences in ultimate failure strength for any of the interference screw biceps tenodesis techniques tested. The tunnel preparation method chosen for interference screw fixed biceps tenodesis can have a positive effect on tenodesis performance. Using the bone wedge technique may allow a more rapid rehabilitation program applicable for the traumatic biceps tendon rupture seen in young, athletic patients with high demands.     

Initial fixation strength of a hybrid technique for femoral ACL graft fixation

Aperture fixation with interference screws matching the diameter of the tunnel is associated with the risk of graft laceration and graft rotation. A hybrid fixation technique (extracortical and aperture fixation) with undersized interference screws provides a higher fixation strength when compared to an aperture fixation using only a screw matching the size of the tunnel and also reduces the risk of graft laceration. This research is an experimental laboratory study. We evaluated the initial fixation strength at time-zero of an extracortical-, a hybrid- and an aperture fixation in ACL reconstruction using extracortical buttons and different sized interference screws in porcine knees. The tests were performed using a single cycle and cyclic loading protocol. Analysis of yield load, maximum load and stiffness in the single cycle loading test showed no statistically significant differences for hybrid fixation with a 1 mm undersized screw and aperture fixation with a screw matching the size of the tunnel. Cyclic loading tests showed a statistically significant difference between hybrid and aperture fixation. The use of an undersized screw alone in aperture fixation resulted in insufficient fixation strength. The initial fixation strength of the hybrid technique with undersized screws is higher compared to an interference screw fixation alone. The hybrid fixation technique is an alternative for ACL graft fixation.     

A new bicortical tibial fixation technique in anterior cruciate ligament reconstruction with quadruple hamstring graft

We report a prospective series of 101 patients receiving a four-strand semitendinosus-gracilis autograft for anterior cruciate ligament reconstruction using a new bicortical tibial fixation technique with bioabsorbable interference screws. Patients (average age 32 years) were operated on between November 1997 and Mai 1998, and follow-up was at least 12 months postoperatively. The evaluation consisted of history, clinical examination, IKDC score, Cincinnati Knee Score, KT-1000 testing, standardized radiography and magnetic resonance imaging. One hundred patients were available for follow-up. There were two traumatic reruptures 6 and 11 months postoperatively. By IKDC score 87 patients were in groups A and B, 12 in group C, and 2 with a rerupture in group D. Mean Cincinnati Knee Score was 82 (range 46–100), KT-1000 manual maximum at follow-up showed an average difference of 1.7 mm between the sides. Full extension was rapidly achieved in all cases, and flexion averaged 135°. Considering the enlargement caused by the bioabsorbable interference screws, the incidence of tunnel widening was 6.6% on the femoral side and 1.7% on the tibial side. Tunnel widening did not affect the clinical results. Three patients experienced an effusion after more than 6 months postoperatively. There was one infection, which settled without functional impairment after early arthroscopic lavage and intravenous antibiotics. Otherwise no complications occurred. The described technique for anterior cruciate ligament reconstruction combines the advantage of anatomical graft position with sufficient graft fixation. A short intra-articular graft construct with a strong tendon to bone interface was created. Clinically, 87% of patients had a normal or nearly normal IKDC score at follow-up. Magnetic resonance imaging revealed a considerable increase in tunnel area caused by the insertion of the interference screws. On the other hand, the development of a “fibrous interzone” between the graft and the bone tunnel was prevented in most cases. At short-term follow-up the bicortical tibial fixation proved to be efficient even with an aggressive rehabilitation program. Received: 26 November 1999 Accepted: 5 March 2000