Rheology of Alkali-Activated Blended Binder Mixtures

Alkali-activated cement (AAC) is an alternative cement that has been increasingly studied over the past decades mainly because of its environmental benefits. However, most studies are on heat-cured AACs and are focused on mechanical properties. There is a lack of research on the fresh properties of ambient-cured AAC systems. This study investigates the rheological properties of ambient-temperature-cured alkali-activated blended binder mixtures activated with sodium silicate and sodium hydroxide solutions. The influence of binder amount, alkaline solid to binder ratio (AS/B), sodium silicate to sodium hydroxide solids ratio (SS/SH), and total water content to total solid (from the binding materials) ratio (TW/TS) on the rheological properties are investigated. The effect of borax as an admixture and silica fume as a replacement for fly ash is also investigated. The results showed that both the yield stress and plastic viscosity are mainly affected by the binder content and TW/TS ratio decreasing with the increase of each parameter. The yield stress increased with the increase of the SS/SH ratio. Borax significantly reduced the yield stress, while silica fume’s effect was dependent on its dosage.     

Rheological Behavior of High-Performance Shotcrete Mixtures Containing Colloidal Silica and Silica Fume Using the Bingham Model

There have been numerous studies on shotcrete based on strength and durability. However, few studies have been conducted on rheological characteristics, which are very important parameters for evaluating the pumpability and shootability of shotcrete. In those studies, silica fume has been generally used as a mineral admixture to simultaneously enhance the strength, durability, pumpability, and shootability of shotcrete. Silica fume is well-known to significantly increase the viscosity of a mixture and to prevent material sliding at the receiving surface when used in shotcrete mixtures. However, the use of silica fume in shotcrete increases the possibility of plastic shrinkage cracking owing to its very high fineness, and further, silica fume increases the cost of manufacturing the shotcrete mixture because of its cost and handling. Colloidal silica is a new material in which nano-silica is dispersed in water, and it could solve the above-mentioned problems. The purpose of this research is to develop high-performance shotcrete with appropriate levels of strength and workability as well as use colloidal silica for normal structures without a tunnel structure. Thereafter, the workability of shotcrete with colloidal silica (2, 3, and 4%) was evaluated with a particle size of 10 nm and silica fume replacement (4 and 7%) of cement. In this study, an air-entraining agent for producing high-performance shotcrete was also used. The rheological properties of fresh shotcrete mixtures were estimated using an ICAR rheometer and the measured rheological parameters such as flow resistance and torque viscosity were correlated with the workability and shootability. More appropriate results will be focusing on the Bingham model properties such that the main focus here is to compare all data using the Bingham model and its performance. The pumpability, shootability, and build-up thickness characteristics were also evaluated for the performance of the shotcrete. This research mainly focuses on the Bingham model for absolute value because it creates an exact linear line in a graphical analysis, which provides more appropriate results for measuring the shotcrete performance rather than ICAR rheometer relative data.     

Influence of Inter-Particle Distances on the Rheological Properties of Cementitious Suspensions

Supplementary cementitious materials (SCMs), such as fly ash (FA), blast furnace slag (BS), and silica fume (SF), have been mostly used as a replacement for Portland cement (PC). Replacing the SCMs with cement can provide improved strength characteristics; however, their applicability depends on the flow characteristics of the fresh mixtures. In this study, the rheological performance of cementitious suspensions in paste scale with different water-to-solid (W/S) volume ratios, varied from 1.25, 1.50, 1.75, 2.00, 2.25, to 2.50, was evaluated. As a result of the rheological tests, the yield stress and plastic viscosity of PC, FA, BS, and SF suspensions decreased as the W/S ratio increased. This study also estimated the inter-particle distances of the cementitious suspensions, and their relationship to the rheological properties was established. The inter-particle distances of the PC, FA, BS, and SF suspensions were in the ranges of 5.74~14.67 µm, 5.18~11.66 µm, 3.82~9.34 µm, and 0.107~0.27 µm, respectively. For very fine particles with a large surface area, the sensitivity to the rheological properties was high and the sensitivity was low when the particle sizes increased, indicating that the rheological properties were more sensitive to fine particles.     

Study on the Influence of Silica Fume (SF) on the Rheology,Fluidity, Stability,Time-Varying Characteristics,and Mechanism of Cement Paste

In this study, the rheology, fluidity, stability, and time-varying properties of cement paste with different substitute contents of silica fume (SF) were investigated. The result showed that the effects of SF on macro-fluidity and micro-rheological properties were different under different water–cement ratios. The addition of SF increased the yield stress and plastic viscosity in the range of 2.61–18.44% and 6.66–24.66%, respectively, and reduced the flow expansion in the range of 4.15–18.91%. The effect of SF on cement paste gradually lost its regularity as the w/c ratio increased. The SF can effectively improve the stability of cement paste, and the reduction range of bleeding rate was 0.25–4.3% under different water–cement ratios. The mathematical models of rheological parameters, flow expansion, and time followed the following equations: τ(t) = τ₀ + k₀t, η(t) = η₀e^at, and L(t) = L₀ − k₁t, L(t) = L₀ − k₁t − a₁t₂. The SF slowly increased the rheological parameters in the initial time period and reduced the degree of fluidity attenuation, but the effect was significantly enhanced after entering the accelerated hydration period. The mechanism of the above results was that SF mainly affected the fluidity and rheology of the paste through the effect of water film thickness. The small density of SF particles resulted in a low sedimentation rate in the initial suspended paste, which effectively alleviated the internal particle agglomeration effect and enhanced stability. The SF had a dilution effect and nucleation effect during hydration acceleration, and the increase of hydration products effectively increased the plastic viscosity.     

The Influence of Hydrated Lime and Cellulose Ether Admixture on Water Retention,Rheology and Application Properties of Cement Plastering Mortars

In this article, the effect of hydrated lime and cellulose ether on the water retention, rheology, and application properties of plasters was studied. For mortars, the consistency, bulk density, and water retention were tested. Rheological measurements of pastes included yield stress and plastic viscosity. In addition to standard tests of mortars and examining the rheological properties of the pastes, a proprietary method for testing the application properties was proposed. The obtained research results made it possible to evaluate the performance of the tested plasters. An attempt was also made to correlate the rheological properties of pastes (plastic viscosity) to the water retention value. The influence of hydrated lime and cellulose ether on selected properties of pastes and plasters was also presented using the statistical Box–Behnken method. The subjective rating of an expert plasterer confirmed the necessity of the modification of plastering mortars with hydrated lime and cellulose ether. As shown, modification of cement plastering mortar with hydrated lime and cellulose ether at the same time allows obtaining a material with favorable technical and technological properties, especially mortars applied by machine.     

Experimental Study on Time-Dependent Changes in Rheological Properties and Flow Rate of 3D Concrete Printing Materials

Three-dimensional concrete printing (3DCP) materials require a relatively low water-to-binder ratio (W/B) of 0.3 or less to ensure their buildability and flow properties are sufficiently maintained after mixing. In this study, the rheological properties of 3DCP materials with W/B 0.28 were evaluated up to 60 min after mixing, and the yield stress and plastic viscosity were analyzed over time. A gradual decrease in flow rate with time was observed during the transport of 200 kg of material per batch through a 20 m hose. To examine the time-dependent changes in flow rate and layer volume, a 2200 mm × 1000 mm test specimen was printed. The dependence of the layer width over time during the printing process was measured and analyzed. The experimental analyses showed that the flow rate and layer volume of the 3DCP material gradually decreased with time after mixing, which was correlated with the rheological properties.     

Aging Resistance of Silica Fume/Styrene-Butadiene-Styrene Composite-Modified Asphalt

The influences of silica fume content and aging on the rheological properties of silica fume/styrene-butadiene-styrene composite-modified asphalts were investigated via rolling thin-film oven test simulations. The asphalts rheological properties before and after aging were measured using three-major-indices, dynamic shear rheology, and bending beam rheometer tests. Fourier transform infrared spectroscopy was used to examine the changes in the functional groups of the asphalt. The silica fume did not chemically react with the modified asphalt, and its original structure was maintained. The aging resistance improved significantly after adding the silica fume. At 6% silica fume content, the relaxation of the asphalt was the highest, indicating that the asphalt had the best low-temperature crack resistance at this mixing proportion. Furthermore, the carbonyl index value of this sample exhibited the smallest increment among all of the samples, and this asphalt sample had the strongest short-term aging resistance. Thus, the optimum silica fume content in the composite-modified asphalt was determined to be 6%. This information may be used to fabricate an asphalt mixture that can improve the service life and aging resistance of pavements.     

The Effect of Class C Fly Ash on the Plasticity and Ageing of Ceramic Mixtures Based on Kaolin

The main aim of the presented article is to describe the behavior of class C fly ash—kaolin plastic doughs during the ageing process. Class C fly ash (CCFA) from the fluidized technology of fuel combustion in a thermal power plant was used as a non-plastic admixture to modify the plasticity in a kaolin–quartz sand mixture (for example, the base of a porcelain mixture). The ageing of plastic ceramic dough determined the effect of the CCFA admixture (0–10–20 wt. %) on the initial water content, plasticity (according to the Pfefferkorn test) and bulk density of a dried green body. The main feature of the CCFA admixture in the kaolin–quartz sand mixture is a solidifying effect. Fly ash increases the initial (mixing) water for the preparation of ceramic dough with constant plasticity (30 mm height of deformed cone Hf, according to the Pfefferkorn test), and Hf increases as the dough ages (the dough solidifies faster and loses its plasticity) with the addition of class C fly ash. The effect of CCFA addition on the plasticity and ageing of kaolin–quartz sand dough is documented on Bigot curves: higher content of fly ash decreases the drying shrinkage of the plastic dough, especially when drying samples that have been aged for 24 h in a plastic wrap (without the possibility of drying). The plastic dough’s ageing increases the porosity of the dried green body with increased content of CCFA in the raw materials mixture and increased ageing time.     

Influence of Silica Fume on High-Calcium Fly Ash Expansion during Hydration

The purpose of this work was to study the possibility of neutralizing high-calcium fly ash expansion during hydration. The object of the study was the fly ash of Berezovskaya GRES, which is capable of independent setting and hardening. The test in the Le Chatelier molds showed that the divergence of indicator arms was 90–100 mm 1 day after mixing with water. The expansion and cracking of the fly ash could be completely prevented by silica fume addition in an amount of 42.9% by weight of the fly ash. At the same time, the compressive strength of specimens from the fly ash–sand paste in a ratio of 1:5 at the age of 28 days was 1.47 MPa. The isothermal heat release at a temperature of 20 °C for 10 days reached 500 kJ/kg. XRF and DTA results showed that free lime in the fly ash was completely hydrated in 11 days and gave the greatest expansion in the absence of silica fume. The presence of silica fume made the lime hydration incomplete and decreased the expansion. Unslaked free lime remained in the system. Exothermic data showed that silica fume inhibited CaO hydration from the reaction start.     

Workability and Mechanical Properties of Superplasticized Microfine Cement Grouts

Superplasticizer (SP) is essential to enhance the groutability of microfine cement (MC) in civil engineering, however, combined effects of cement type, SP type, amount of SP and water-solid ratio (W/S) on engineering performance of MC are not clear currently. In this research, workability and mechanical properties of superplasticized microfine cement grouts (SMCG) with various SPs are evaluated systematically. Three different MCs (CEM I, CEM II/B-M and CEM III/B based on EN 197-1) and four SPs (one naphthalene-based (N), one melamine-based (M) and two polycarboxylate-based (PCE)) were used to study the effect of grout formulation. The properties investigated included rheological behavior (mini-slump, flowability, time-dependent viscosity and initial viscosity), fresh-state property (bleeding, effective W/S and final setting time), mechanical performance (shrinkage, flexural strength (FS), unconfined compressive strength (UCS), and FS/UCS) and microstructure. The new method of static viscosity was adopted and viscoelasticity was evaluated. The ranges of W/S and SP content were 1.0–2.0 and 0–2.5%, respectively. The results show that the dispersion effects of SP on rheological behavior were followed by PCE, M and N in order of the influence degree. The instability, long-setting and oversaturation were easily caused by excessive SP. SP could be helpful for improving FS or bending toughness. Considering workability and mechanical performance of SMCG, the W/S is suggested to be within 1.5, the optimal amounts of N, M and PCE are recommended as 1.5–2.0%, 1.2–1.5% and 0.9–1.2%, respectively.     

Investigation on Rheological Properties of Water-Based Novel Ternary Hybrid Nanofluids Using Experimental and Taguchi Method

This study presents the rheological behavior of water-based GO-TiO₂-Ag and rGO-TiO₂-Ag ternary-hybrid nanofluids. The impact of nanoparticles’ volumetric concentration and temperature on the rheological properties were studied. All experiments were performed under temperatures ranging from 25 to 50 °C in the solid volume concentration range of 0.5–0.00005%. The data optimization technique was adopted using the Taguchi method. The types of nanomaterials, concentration, temperature, and shear rate were chosen to optimize the viscosity and shear stress. The effect of shear stress, angular sweep, frequency sweep, and damping factor ratio is plotted. The experimental results demonstrated that the rheological properties of the ternary hybrid nanofluid depend on the ternary hybrid nanofluid’s temperature. The viscosity of ternary hybrid nanofluids (THNf) change by 40% for GO-TiO₂-Ag and 33% for rGO-TiO₂-Ag when temperature and shear rates are increased. All the ternary hybrid nanofluids demonstrated non-Newtonian behavior at lower concentrations and higher shear stress, suggesting a potential influence of nanoparticle aggregation on the viscosity. The dynamic viscosity of ternary hybrid nanofluid increased with enhancing solid particles’ volume concentration and temperature.     

MoS2 Nanoparticle Effects on 80 °C Thermally Stable Water-Based Drilling Fluid

Bentonite-based drilling fluids are used for drilling, where inhibitive fluids are not required. The rheological and the density properties of the drilling fluids are highly affected by high temperature and pressure. Due to high temperature, the clay particles stick together, and the fluid system becomes more flocculated. Poorly designed drilling fluid may cause undesired operational issues such as poor hole cleaning, drill strings sticking, high torque and drag. In this study, the 80 °C thermally stable Herschel Bulkley’s and Bingham plastic yield stresses drilling fluids were formulated based on lignosulfonate-treated bentonite drilling fluid. Further, the impact of a MoS₂ nanoparticle solution on the properties of the thermally stable base fluid was characterized. Results at room temperature and pressure showed that the blending of 0.26 wt.% MoS₂ increased the lubricity of thermally stable base fluid by 27% and enhanced the thermal and electrical conductivities by 7.2% and 8.8%, respectively.     

Study on the Physical and Chemical Properties of Cement-Based Grout Containing Coal–Fly Ash

To study the physical and chemical properties of grout containing fly ash, Class II fly ash was used as a mineral admixture and mixed with silicate cement to produce grout, and the rheological properties, strength properties, hydration properties, and microscopic mechanism were studied. The results of the study showed the following. The incorporation of fly ash reduced the thixotropic area of the composite cement slurry, which facilitated pumping in the pipeline conveying process. The inclusion of fly ash reduced the yield stress and plastic viscosity of the cement paste, but the rheological index increased and then decreased with the increase in fly ash, and the composite paste had the lowest degree of shear thinning at 30% fly ash inclusion. The incorporation of fly ash reduced the hydration exothermic rate and total hydration exothermic amount of the composite slurry and prolonged the hydration induction period, but the promotion effect of fly ash on the hydration rate of cement was obvious at 10% fly ash admixture. The admixture of fly ash increased the empty volume of the composite slurry, but the effect on the most probable aperture was not significant, and the porosity of the system increased, resulting in a decrease in compressive strength. The effect of adding fly ash on the hydration products was reflected mainly by the C-S-H gel produced by cement hydration and the change in calcium alumina and Ca(OH)₂. Fly ash does not directly participate in the hydration reaction of cement, but it can promote cement hydration and increase the reaction rate of cement. By analyzing the rheological properties, mechanical properties, and hydration properties of fly ash composite cement paste, the comprehensive analysis found that the rheological properties are excellent when the fly ash admixture is 20–30%, and the water–cement ratio can be reduced to improve the strength without affecting the pumping demand.     

Yield-Point Phenomenon and Plastic Bands in Ferrite–Pearlite Steels

Lüders deformation is one type of discontinuous yielding in ferrite–pearlite steel. The yield-point phenomenon and localized plastic bands are two features of the Lüders phenomenon. It is believed that the yield-point phenomenon is related to the formation of plastic bands, but the correlation between them is unclear. In this study, this correlation was investigated by examining the global and local deformation behaviors in the tension processes of four ferrite–pearlite steels (carbon content, 0.05–0.3%; pearlite fraction, 1.2–32%) via an extensometer and digital image correlation (DIC) technique. The main obtained results are as follows: (1) the degree of yield drop decreased with an increase in the pearlite fraction (the magnitude of the yield stress drop was 8.6–0 MPa), and (2) a plastic band was formed at a certain stress level smaller than the upper yield stress; when the stress level was larger than 92% of the upper yield stress, the upper yield point disappeared.     

Investigating the Mechanical and Durability Characteristics of Fly Ash Foam Concrete

Although fly ash foam concrete (FAFC) is lightweight, heat-retaining, and insulating, its application options are constrained by its weak construction and short lifespan. The effects of various dosage ratios of the foaming agent (i.e., hydrogen peroxide), silica fume, and polypropylene fiber on the dry density, compressive strength, thermal insulation performance, pore structure parameters, and durability of FAFC were analyzed in this study, which sought to address the issues of low strength and low durability of FAFC. According to the findings, there is a negative correlation between the amount of hydrogen peroxide (as the foaming agent) and compressive strength, and, as the silica fume and polypropylene fiber (PP fiber) content rise, the strength will initially rise and then fall. The distribution of pore sizes gradually shifts from being dominated by small pores to large pores as the amount of foaming agent increases, while the porosity and average pore size gradually decrease. When the hydrogen peroxide content is 5%, the pore shape factor is at its lowest. The pore size distribution was first dominated by a small pore size and thereafter by a large pore size when the silica fume and PP fiber concentration increased. Prior to increasing, the porosity, average pore size, and pore shape factor all decreased. Additionally, the impact of PP fiber on the freeze–thaw damage to FAFC was also investigated at the same time. The findings indicate that the freeze–thaw failure of FAFC is essentially frost heave failure of the pore wall. The use of PP fiber is crucial for enhancing FAFC’s ability to withstand frost. The best frost resistance is achieved at 0.4% PP fiber content. In conclusion, the ideal ratio for overall performance was found to be 5% hydrogen peroxide content, 4% silica fume content, and 0.1% polypropylene fiber content. The results obtained could be applied in different fields, such as construction and sustainable materials, among others.     

An Experimental Investigation on the Thermo-Rheological Behaviors of Lactic Acid-Based Natural Deep Eutectic Solvents

The rheological studies of Lactic Acid (LA)-based Natural Deep Eutectic Solvents (NADES) are provided in the present investigation. Those mechanisms were also studied in which three distinct Hydrogen Bond Acceptors (HBAs) of Choline Chloride (ChCl), Betaine (Be), and β-Alanine (β-Al), after being added to a specific Hydrogen Bond Donor (HBD) at a predefined mole-to-mole ratio of 1:1, affected the rheological properties of the prepared NADES. The alterations in the rheology-related characteristics in association with the mechanical and physical properties indicate the tolerance of the material under various operational conditions in the field and show their potential utilization as environmentally suitable and feasible solvents for industrial applications. In the present research, the viscoelastic properties of the three samples of NADES were assessed along with their shear flow properties. The backward and forward temperature change in the Apparent Viscosity (AV) pattern related to the NADES system was described by a rheogram. Furthermore, the density was determined and compared with the AV while considering the temperature-related factor. On a further note, the viscoelastic characteristics were utilized in describing and investigating the network disturbance on the level of the microstructure of NADES upon frequency sweep. A series of experiments were carried out using Thermogravimetry Analysis (TGA) to investigate the thermo-physical properties to optimize them. The rheological properties of shear flow measurements were analyzed using the Bingham model that is best suited for the AV developed with the shear rate with the dynamic yield stress of three systems. The Bingham model was used to determine the lowest stress necessary to disturb the network structure and commence the flow of LA-based NADES. Overall, the viscoelastic behavior of the LA-based NADES revealed the dissimilarity between their strength and viscosity. In addition, shear flow investigations demonstrated that LA-based NADES systems exhibit non-Newtonian properties and substantial shear-thinning effects equivalent to those of alternative IL sorbents. Assessing the rheological properties of LA-based NADES is crucial for a better understanding the key challenges associated with high viscosity. Defining the transport yield stress requirements for NADES systems under different conditions benefits their future development and potentially opens the door to more challenging applications.     

Printability,Thermal and Compressive Strength Properties of Cementitious Materials: A Comparative Study with Silica Fume and Limestone

Over the past decade, 3D printing in the construction industry has received worldwide attention and developed rapidly. The research and development of cement and concrete products has also become quite well-established over the years, while other sustainable materials receive considerably lower attention in comparison. This study aims to investigate the influence of the two most commonly used sustainable cementitious materials i.e., silica fume and limestone powder, on printability, thermal and mechanical properties of fly ash–Portland cement blends. Ternary blends containing Portland cement, fly ash and silica fume or limestone powder are prepared, whereas phase change material (PCM) is introduced to improve the thermal behavior. Based on the rheological properties and concurrent 3D concrete printing, improved buildability of the modified mixtures is linked to their static yield stress. Anisotropic mechanical properties are observed for 3D printed specimens, while cast specimens exhibit a maximum 41% higher compressive strength due to better material compaction. It is clear from the results that addition of silica fume and limestone powder ranged from 5% to 10%, reducing the anisotropic mechanical properties (maximum 71% and 68% reduction in anisotropic factor, respectively) in the printed specimens. The PCM addition ranged from 5% to 10% and improved thermal performance of the mixtures, as measured by a decrease in thermal conductivity (9% and 13%) and an increase in volumetric heat capacity (9% and 10%), respectively. However, the PCM-containing mixtures show around 29% reduction in compressive strength, compared to the control specimen, which necessitates new material design considering matrix strengthening methods.     

Optimization Based on Toughness and Splitting Tensile Strength of Steel-Fiber-Reinforced Concrete Incorporating Silica Fume Using Response Surface Method

The greatest weakness of concrete as a construction material is its brittleness and low fracture energy absorption capacity until failure occurs. In order to improve concrete strength and durability, silica fume SF is introduced into the mixture, which at the same time leads to an increase in the brittleness of concrete. To improve the ductility and toughness of concrete, short steel fibers have been incorporated into concrete. Steel fibers and silica fume are jointly preferred for concrete design in order to obtain concrete with high strength and ductility. It is well-known that silica fume content and fiber properties, such as aspect ratio and volume ratio, directly affect the properties of SFRCs. The mixture design of steel-fiber-reinforced concrete (SFRC) with SF addition is a very important issue in terms of economy and performance. In this study, an experimental design was used to study the toughness and splitting tensile strength of SFRC with the response surface method (RSM). The models established by the RSM were used to optimize the design of SFRC in terms of the usage of optimal silica fume content, and optimal steel fiber volume and aspect ratio. Optimum silica fume content and fiber volume ratio values were determined using the D-optimal design method so that the steel fiber volume ratio was at the minimum and the bending toughness and splitting tensile strength were at the maximum. The amount of silica fume used as a cement replacement, aspect ratio, and volume fraction of steel fiber were chosen as independent variables in the experiment. Experimentally obtained mechanical properties of SFRC such as compression, bending, splitting, modulus of elasticity, toughness, and the toughness index were the dependent variables. A good correlation was observed between the dependent and independent variables included in the model. As a result of the optimization, optimum steel fiber volume was determined as 0.70% and silica fume content was determined as 15% for both aspect ratios.     

Rheological Properties and Early-Age Microstructure of Cement Pastes with Limestone Powder,Redispersible Polymer Powder and Cellulose Ether

In order to study the synergistic effects of organic and inorganic thickening agents on the rheological properties of cement paste, the rheological parameters, thixotropy cement-paste containing limestone powder (LP), re-dispersible polymer powder (RPP), and hydroxypropyl methylcellulose ether (HPMC) were investigated using the Anton Paar MCR 102 rheometer at different resting times. The early-age hydration process, hydration products, and microstructure were also analyzed with scanning electron microscopy (SEM) and thermogravimetry analyses (TGA). The results showed that the addition of LP, RPP, and HPMC affected the rheological properties of cement paste, but the thickening mechanism between organic and inorganic thickening agents was different. The small amount of LP increased the plastic viscosity but decreased the yield stress of cement paste due to its dense filling effect. Adding 1% of RPP improved the thixotropic property of cement paste by 50%; prolonging the standing time could improve the thixotropic performance by as much as two times. Only 0.035% HPMC added to the cement paste increased the plastic viscosity by 20%, while the yield stress increased nearly twice. The more HPMC added, the more significant effect it showed. Cement paste compounds with LP, RPP, and HPMC balanced the yield stress and plastic viscosity and improved the thixotropy. The C-L6-R1.0-H0.035 paste presented as a pseudoplastic, its rheological indexes were close to one, and it was hardly affected by the resting time. The composite superposition effect of organic and inorganic thickening agents reduced the impact of resting time for all pastes. As the organic thickening component inhibited the hydration more than the LP promoted the hydration of the cement paste, indicating that the C-L6-R1.0-H0.035 paste remained in the particle fusion stage after curing for three days, as shown by the SEM images.     

Concrete Modular Pavement Structures with Optimized Thickness Based on Characteristics of High Performance Concrete Mixtures with Fibers and Silica Fume

Usually, C30/37 strength class concrete is used to construct concrete pavements on a rigid, semi-rigid or flexible base. Concrete with such a strength delivers essential design characteristics: flexural strength and tensile splitting strength are between 4.5–5.4 MPa and 2.8–3.7 MPa, respectively. Design characteristics can be significantly increased by densifying the concrete mixture, i.e., adding silica fume, steel or polypropylene macro fibers. As high-performance concrete characteristics are 20–60% higher than those for standard concrete (C30/37), new possibilities to reduce the thickness of concrete pavement slabs appear. The theoretical analysis of concrete pavement structures with high-performance concrete mixtures (C40/50, C45/55 and C50/60) showed that slab thickness could be reduced by 6–39% compared to a standard concrete pavement structure depending on the concrete properties and design method. From all those pavement structures, three concrete mixtures were determined as the most rational ones in terms of PCP thickness reduction and total pavement cost: (i) with 49.5 kg/m³ of steel fibers and 25.2 kg/m³ of silica fume; (ii) with 10.0 kg/m³ of polypropylene fibers (type A); (iii) with 49.5 kg/m³ of steel fibers.