Polycondensations of Bisphenol‐A with Diphosgene or Triphosgene in Water‐Free Organic Solvents

Summary: Bisphenol‐A was polycondensed with diphosgene and excess pyridine in a mixture of dry dichloromethane and 1,4‐dioxane. The stoichiometry was varied to optimize the molecular weight. According to MALDI‐TOF mass spectra the fraction of cyclic polycarbonates increased with higher molecular weights. Analogous results were obtained with triphosgene. When pyridine was replaced by triethylamine, diethyl carbamoyl chloride was formed and an excess of diphosgene (plus triethylamine) yielded polycarbonates having one or two diethylcarbamate endgroups. However, the content of cycles increased again with the molecular weight and peaked for the sample with the maximum molecular weight. ¹H NMR endgroup analyses confirmed the interpretation of the MALDI‐TOF mass spectra. SEC measurement indicated high polydispersity indices (around 7) for samples rich in cycles.

     

Synthesis and Hole‐Transporting Property of a Novel Poly(N‐vinylcarbazole) Copolymer with Metal‐Coordination Sites

Summary: Hole transporting poly(N‐vinylcarbazole) copolymers with phenylazomethine dendron units acting as metal ligation sites were synthesized. These polymers possess both hole‐transport and metal‐collecting units with simple σ‐bond linkages. Complexation in the phenylazomethine dendron unit within these copolymers by SnCl₂ has been successfully observed by the change in the UV‐vis spectra. The complexation changes the HOMO/LUMO energy gap that results in a spectral red‐shift. Using copolymers as a hole‐transport layer, only complexation with metal ions leads to an enhanced maximum luminescence. Such a complexation results in a high electroluminescence efficiency because the p‐type‐doped structure acts as the hole‐transport layer.

Copolymerization for the preparation of DPAGn(x)‐Cbz(y).     

Solid‐State Olefin Metathesis: ADMET of Rigid‐Rod Polymers and Ring‐Closing Metathesis

Summary: Solid‐state olefin metathesis of rigid‐rod acyclic diene metathesis (ADMET) polymers and ring‐closing metathesis (RCM) have been investigated. 1,4‐Dipropoxy‐2,5‐divinylbenzene ( 4 ) was synthesized and used in a bulk ADMET polymerization to produce oligomers of dialkoxy poly(phenylene vinylene). The reaction was continued in the solid state, effectively doubling the molecular weight. Solid‐state RCM was investigated with a variety of solid dienes and metathesis catalysts, and demonstrated in low conversions using amide diene 5 with catalysts 9 , 13 , and 14 .

     

Lanthanide Metal‐Organic Frameworks as Ziegler–Natta Catalysts for the Selective Polymerization of Isoprene

The unprecedented ability of neodymium‐based metal organic frameworks (MOFs) as polymerisation pre‐catalysts towards isoprene is reported. Combined with methylaluminoxane (MAO) or modified MAO (MMAO), they afford mainly cis‐selective polyisoprene, up to 90.7%. Both the activity and the selectivity are tentatively ascribed to the intrinsic microstructure of the starting materials. Compared to conventional carboxylates, MOFs associated to an Al co‐catalyst are less active but the selectivity is found to be higher, and it may be modified by controlling the access to the pores, which would be favored at higher temperatures. Some residual crystalline MOF remains disseminated within the polymer matrix, as shown by X‐ray diffraction and X‐ray absorption spectroscopy studies.

     

Chain Growth Polycondensation as a Polymer Generating Reaction in the Synthesis of Oligo(p‐phenyleneethynylene)s with Low Polydispersity

Summary: The polycondensation of 1‐ethynyl‐2,5‐dihexyl‐4‐iodobenzene in the presence of 1‐ethynyl‐2,5‐dihexyl‐4‐(2‐phenylethynyl)benzene proceeds according to the mechanism of initiated chain growth polycondensation. It has allowed the synthesis of oligomers with a desired molecular weight and a narrow molecular weight distribution. The reasons for the side reaction leading to the formation of diyne compounds are revealed and the presumed mechanism is given. This opens prospects for the preparation of defectless poly(p‐phenyleneethynylene)s with required molecular weights and narrow molecular weight distributions.

     

Pseudo‐Living Anionic Telomerization of Buta‐1,3‐diene

Low‐molecular‐weight liquid polybutadienes (1 000–2 000 g · mol^?1) consisting of 60 mol‐% poly(buta‐1,2‐diene) repeating units were synthesized via anionic telomerization. Maintaining the initiation and reaction temperature at less than 70 °C minimized chain transfer and enabled the polymerization to occur in a living fashion, which resulted in well‐controlled molecular weights and narrow polydispersity indices. MALDI‐TOF mass spectrometry confirmed that the end groups of liquid polybutadienes synthesized via anionic telomerization contained one benzyl end and one protonated end. In comparison, the end groups of liquid polybutadienes synthesized via living anionic polymerization contained one sec‐butyl or butyl end and one protonated end.

     

Synthesis of Silica‐Supported Metallocene Catalysts for Olefin Polymerization

Four supported metallocene catalysts were synthesized directly on silica [Si(CpZrCp), Si(CpZrInd), Si(IndZrCp), and Si(IndZrInd)]. The first ligand was chemically tethered to silica (internal ligand) while the second was free from silica (external ligand). The polymerization of ethylene and the copolymerization of ethylene with hexene were investigated. The activity of the catalysts and the molecular weights of the polymers were found to depend on the position of the ligands. In all cases, high‐molecular‐weight polyethylene with moderate polydispersity was obtained. Moreover, the copolymerization of ethylene with hexene provided a homogeneous polymer.

Reaction of ZrCl₄(OC₄H₈)₂ with modified silica (SiCp).     

Rapid Synthesis and MALDI‐ToF Characterization of Poly(ethylene oxide) Multiarm Star Polymers

Multiarm PEO star polymers with a purely aliphatic polyether structure have been synthesized using hyperbranched polyglycerol (PG) with different molecular weights as a multifunctional initiator. Different degrees of deprotonation of the initiator were studied with respect to molecular weight control. The results show that the degree of deprotonation is a crucial parameter for the synthesis of well‐defined polymers with controlled molecular weights. Partial deprotonation of the PG hydroxyl groups (5–8%) was proven to represent an optimum for the synthesis of star polymers with molecular masses close to the theoretical values. Molecular weights of the stars ranged between 9 000 and 30 000 g · mol^?1. MALDI‐ToF spectra confirmed that the PEO arms in the star polymers possess homogeneous lengths.

     

Peroxide‐Grafted PDMS: Hydrosilylation Reaction and Thiol‐Ene Chemistry as an Alternative Pathway

Peroxide‐containing PDMS was synthesized according to a new pathway. Although hydrosilylation is one of the main reactions carried out in silicone chemistry, the catalysts used are very sensitive to the chemical nature of the reactants and remained inefficient to graft allylic peroxide. Radical catalyzed thiol‐ene chemistry was involved for the first time to yield an initiator group containing polymer. The peroxide‐grafted polysiloxane structure and decomposition were characterized using ¹H, ¹³C and ²⁹Si NMR, FT‐IR and Raman spectroscopies, SEC and DSC. These macroinitiators can be used to obtain polysiloxane able to undergo crosslinking.

     

Metathetic Selective Degradation of Polyisoprene: Low‐Molecular‐Weight Telechelic Oligomer Obtained from Both Synthetic and Natural Rubber

Summary: Degradation studies of cis‐1,4‐polyisoprene were carried out using first and second generation Grubbs catalysts to achieve end‐functionalized acetoxy oligomers in both an organic solvent and a latex phase at room temperature. Well‐defined acetoxy telechelic polyisoprene structures were obtained in a selective manner with a range of from 10 000 to 30 000, with a polydispersity index of around 2.5.

Structure produced by the metathetic depolymerization of hydroxy telechelic cis‐1,4‐polyisoprene.     

A Study of Copolymerization of 1‐Hexene with 2,5‐Norbornadiene Using Metallocene Catalysts

Summary: Copolymerization of 1‐hexene with a symmetrical diene, namely 2,5‐norbornadiene was studied using four different metallocene catalysts. Copolymerization was found to occur exclusively through one of the two equally reactive endocyclic double bonds with all the four catalysts. Copolymerization results in low molecular weight oligomers with the number average molecular weight ( ) varying from 1 000–3 000. End group analysis of the co‐oligomers revealed that the β‐hydrogen transfer after 2,1 insertion also occurs in the presence of highly regiospecific catalysts. The regio errors were also found to depend on various reaction parameters such as polymerization time, Al/Zr mol ratio, metallocene concentration and polymerization temperature.

Plots of variation in end groups and NBD incorporation with time.     

From CO2‐Based Multifunctional Polycarbonates With a Controlled Number of Functional Groups to Graft Polymers

Copolymerization of CO₂ and epoxides is employed to generate functional polycarbonates. The introduction of reactive double bonds at a poly(propylene carbonate) (PPC) backbone is realized by the copolymerization of aliphatic alkene epoxides with propylene oxide (PO) and carbon dioxide (CO₂). A series of copolymers with random structure and varying comonomer content (3–22%) with molecular weights in the range of 22 000–34 000 g mol^?1 is synthesized and characterized with respect to their microstructure and thermal properties. The facile transformation of the double bonds is verified by a thiol‐ene reaction, resulting in quantitative conversion of the double bonds. Polycarbonate derivatives with multiple functionalities are prepared, providing suitable moieties for further grafting.

     

Synthesis and self‐assembly of polymers containing dicarboximide groups by living ring‐opening metathesis polymerization

Polymers with narrow molecular weight distributions and controlled architectures were generated by living ring‐opening metathesis polymerization of exo‐7‐oxabicyclo[2.2.1]hept‐5‐ene‐2,3‐dicarboximide. The dicarboximide units have been previously shown to exhibit biological activity, can selectively bind to the nucleic acid base adenine by hydrogen‐bonding, and are readily functionalizable. Block copolymers containing these moieties were generated, and underwent self‐assembly into nanoscale spherical aggregates, with surface localized molecular recognition motifs.

     

Fluorene‐Based Single‐Chain Copolymers for Color‐Stable White Light‐Emitting Diodes

Fluorene‐based single‐chain copolymers with a white light emitter consisting of a blue and an orange chromophore have been synthesized and their photophysical and electroluminescent properties are investigated. The experimental results suggest that only a relatively small fraction of the orange‐emitting units incorporated into the fluorene is needed to achieve efficient white light emission by controlled incomplete energy transfer. A device from a copolymer with 0.02% DDQ content showed the highest external quantum efficiency of 2.64% with a luminance efficiency of 4.06 cd · A^?1 with CIE coordinates (0.28, 0.24). The EL emissions are extremely stable over a wide range of current densities.

     

Nitroxide‐Mediated Radical Polymerization of N‐tert‐Butylacrylamide

The nitroxide‐mediated polymerization of N‐tert‐butylacrylamide (TBAM) in DMF at 120 °C using SG1/DEPN and AIBN has been investigated. Linear growth in number‐average molecular weight ( ) versus conversion and narrow molecular weight distributions (MWDs) with high livingness were obtained up to ≈8 000 g · mol^?1. For higher molecular weights, the MWDs gradually became broader with low molecular weight tailing, and deviated downwards from theoretical values. Quantitative analyses of MWDs, along with specifically designed conventional radical polymerizations at 120 °C, were consistent with chain transfer to monomer limiting the attainable . This finding can be equally applied to existing literature polymerizations of TBAM.

     

Macrocycles, 22

The phosgenation of bisphenol A with diphosgene in the CH₂Cl₂/NaOH system was studied using the pseudo‐high‐dilution method either with triethylamine, with triethylbenzyl ammonium chloride (TEBA‐Cl), or with tetraphenylphosphonium chloride as catalyst. For Ph₄PCl, only low‐molecular‐weight polycarbonates containing various by‐products were obtained. With the TEBA catalyst, the fraction of cycles and the average molecular weights increased with higher feed ratios of the catalyst. Both the fraction of cycles and the molecular weights steeply decreased at higher temperatures. With triethylamine as catalyst both the fraction of cycles and molecular weight passed through a maximum at low catalyst concentration, when the feed ratio of triethylamine was varied. Higher temperatures favored slightly lower fractions of cycles and lower molecular weights. Samples containing ≥ 95 mol‐% of cycles were obtained. The cycles were identified by matrix‐assisted laser desorption ionization time‐of‐flight (MALDI‐TOF) mass spectrometry up to 22 000 Da in the case of virgin samples, and up to 55 000 Da after fractionation by size exclusion chromatography (SEC). Selected samples were characterized by SEC measurements and evaluated by the triple‐detection method. High polydispersities and a tendency towards a bimodal mass distribution were found, when triethylamine was used as catalyst.

MALDI‐TOF mass spectrum of a polycarbonate prepared by triethylamine‐catalyzed phosgenation at 20 °C by the pseudo‐high‐dilution method.     

Synthesis,Electrochemical and Photovoltaic Properties of Multi‐Armed Polythiophenes with Triphenylamine Trivinylene as Conjugated Linker

Three polythiophenes with 5%, 10% and 15% triphenylamine trivinylene (TPAV) as bridge linker, PT‐TPAV5, PT‐TPAV10 and PT‐TPAV15, were synthesized. The Wittig‐Horner‐Emmons reaction and the Stille method were employed to synthesize these polymers. The polythiophenes were subsequently used in bulk‐heterojunction polymer solar cells (PSCs) as donor materials. The polymers exhibited a striking and reversible color change after the oxidation of the polymer films. The power conversion efficiencies of the PSCs based on PT‐TPAV5, PT‐TPAV10 and PT‐TPAV15 as donors and PCBM as acceptor were 0.17%, 0.50%, and 0.35%, respectively, under the illumination of AM 1.5, 100 mW · cm^?2.

     

Novel Phosphorous‐Containing Aromatic Polyethers – Synthesis and Characterization

Summary: The synthesis of novel phosphorous‐containing aromatic polyethers P‐PEEK and P‐PSU, based on poly(ether ether ketone)s (PEEK) and poly(ether sulfone)s (PSU) was carried out successfully by using phosphorous‐containing aromatic diols instead of bisphenol A in the usual synthesis procedure. The molecular weights of the P‐PEEKs and P‐PSUs obtained reflect both the influence of the different halogen components used and the lower thermal stabilities of the phosphorous‐containing diols compared to bisphenol A. However, polymers with sufficient molecular weights could be obtained, having interestingly high T_gs, high thermal stabilities as well as modified flame retardance properties depending on the diol type incorporated.

Comparison of the molecular weights of the synthesized P‐polyethers.     

Thermally Reversible Cross‐Linked Polyamides with High Toughness and Self‐Repairing Ability from Maleimide‐ and Furan‐Functionalized Aromatic Polyamides

Polyamides having various amounts of maleimide (PA‐MI) and furan (PA‐F) pendent groups, respectively, as well as their cross‐linked polymers (PA‐MI/PA‐F) were prepared. PA‐MI/PA‐F cross‐linked polymers showed thermally reversible cross‐linking behavior via Diels‐Alder (DA) and retro‐DA reactions. Cross‐linked PA‐MI/PA‐F films exhibited enhanced toughness and mechanical properties compared to PA‐MI and PA‐F precursors. Moreover, PA‐MI/PA‐F films also showed thermal self‐repairing behavior, which was observed in the micrographs and instron tests.

     

Nanoscale Blends between Immiscible Polymers via Simultaneous Non‐Interfering Polymerisation

Summary: An important topic in polymer science seeks to improve the performances of polymer blends using nanoscale phase segregation. Here, blends between polystyrene and polycaprolactone are realised by a chemical route. The non‐interfering character of the radical polymerisation of styrene and the lanthanide halide initiated ring‐opening polymerisation of caprolactone is assessed. The molecular weights range from 2 000 to 3 500 for polycaprolactone and up to 140 000 for polystyrene, with reasonable polydispersity indexes. From calorimetry measurements, it is shown that polystyrene and low molecular weight polycaprolactone are immiscible. The morphology of the blends between the two immiscible polymers studied by atomic force microscopy is consistent with nanometer‐scale phase segregation.

AFM surface image of a nanoscale blend.