Synthesis,Characterization, and Intramolecular End‐to‐End Ring Closure of α‐Isopropylidene‐1,1‐dihydroxymethyl‐ω‐diethylacetal Polystyrene‐block‐polyisoprene Block Copolymers

Cyclic polystyrene‐block‐polyisoprenes of controlled dimensions have been synthesized for the first time by the direct coupling of α‐isopropylidene‐1,1‐dihydroxymethyl‐ω‐diethylacetal‐heterodifunctional linear polystyrene‐block‐polyisoprene precursors previously prepared by living anionic polymerization. Cyclization is achieved under high dilution by intramolecular coupling of the polymer ends under acid catalyst conditions. Using this strategy polystyrene‐block‐polyisoprene macrocycles of controlled chain dimensions are prepared in high yield (> 90%). Pure cycles were finally recovered by flash chromatography. The synthesis and characterization of both the linear α,ω‐heterodifunctional polystyrene‐block‐polyisoprenes block copolymers precursors and of the corresponding cyclized chain architectures are reported.

200 MHz ¹H NMR spectrum (CDCl₃) of cyclized polystyrene‐block‐polyisoprene copolymer (M _n = 12 000).     

A Concerted H‐Bonding Self‐Assembly‐Based Approach to Ladder Poly(silsesquioxane)

Summary: A soluble, regular, ethoxy‐capped, ladder poly(silsesquioxane) ( EtO‐LPOAS ) has been successfully synthesized by means of the concerted H‐bonding template of silanol and amido groups, through a new template monomer M : tetraethoxy disiloxane bisamide compound. EtO‐LPOAS was characterized by X‐ray diffraction (XRD), ²⁹Si NMR spectroscopy and DSC measurements. The results confirm the presence of the regular, ladder structure of EtO‐LPOAS . This synthetic method has opened a new route to other new kinds of functional ladder poly(silsesquioxane)s.

Schematic overview of the mechanism for synthesis of EtO‐LPOAS .     

Pyrene Containing Polymers for the Non‐Covalent Functionalization of Carbon Nanotubes

Pyrene containing diblock copolymers based on poly(methyl methacrylate) were synthesized and investigated regarding their adsorption on carbon nanotubes (CNT). The pyrene units were introduced using a reactive ester monomer for the build up of the second block which later on was reacted polymer‐analogously with amine functionalized pyrene derivatives. As we started from the same reactive ester intermediate, full block length identity is given. We varied the length of the anchor block to find an optimal block length and used pyren‐1‐yl‐methylamine as well as 4‐pyren‐1‐yl‐butylamine as anchor units. For both anchor units a maximal adsorption was found for 13 and 20 anchor units, respectively. The absolute adsorption was best for the 4‐pyren‐1‐yl‐butylamine anchor units as the longer spacer enhances the mobility of the anchor unit. The dispersion diagram of CNTs and diblock copolymer in terms of dispersion stability was investigated and a stable dispersion of 2.5 mg · ml^?1 CNTs in THF was found.

     

A Poly(vinyl alcohol)‐graft‐Copolyester: Synthesis of a Novel Graft Copolymer Containing Adamantane Moieties as Guest for Cyclodextrin

A novel graft copolymer is synthesized from commercially available poly(vinyl alcohol) using ring‐opening polymerization. For the polymerization reaction of novel brush‐like poly(vinyl alcohol)‐graft‐poly(?‐caprolactone‐co‐(3‐/7‐(prop‐2‐ynyl)oxepan‐2‐one) 5 Sn(Oct)₂ is used as a catalyst. The formation of the graft copolymer is confirmed by ¹H NMR, ¹³C NMR, and Fourier transform infrared (FTIR) spectroscopy. Furthermore, the modification of the novel synthesized graft copolymer via a “click” reaction to implement adamantane groups is described. The success of the “click” reaction is proven by ¹H NMR spectroscopy and visualized by decomplexation of cyclodextrin with included phenolphthalein.

     

Preparation of pH‐Responsive Hydrophilic Core‐Shell Particles for Encapsulation of Water‐Soluble Material

Dual pH‐responsive PAAc/ PVAm core‐shell particles to encapsulate water‐soluble material were prepared through the deposition of PVAm on the surface of PAAc core particles. The structural characteristics of the core‐shell particles were confirmed by SEM and CLSM. To investigate the release profiles of the core‐shell particles and PAAc core, methylene blue, which is a cationic water‐soluble dye, was introduced. Release profiles were dominantly affected by the core swelling behavior at different pH values. The release rate of the core‐shell was less than the PAAc core, indicating that it is affected by ionic interactions between the particle and the cationic dye.

     

Stabilization in Water of Polymer/Cu2+ Complexes Using Poly(sodium acrylate)‐graft‐poly(N,N‐dimethylacrylamide) Graft Copolymers

The formation of complexes between Cu²⁺ ions and graft copolymers built from a PANa backbone and non‐ionic hydrophilic PDMAM side chains is investigated by means of turbidimetry, viscometry, DLS, ζ‐potential measurements, and UV‐vis spectrophotometry. The macroscopic phase separation which accompanies complexation is gradually depressed with increasing PDMAM content x, and water‐soluble complexes are formed for x = 70 mol‐%. The polymer/Cu²⁺ complexation is a charge neutralization process that leads to the formation of water‐soluble, compact, hybrid polymer/metal ion nanostructures. UV‐vis data indicate that this graft copolymer could possibly serve as a water‐soluble sensor for Cu²⁺ ions.

     

Synthesis of Diene‐Functionalized Macromonomers via Functionalization with Hexa‐1,3,5‐triene

The reaction of poly(styryl)lithium (PSLi) with hexa‐1,3,5‐triene (HXT) was studied as a route to diene‐functionalized macromonomers. When PSLi was reacted with 1.5 molar equivalents of HXT for 2.5 h at ?10 °C in toluene, it was found that the diene‐functionalized macromonomer was obtained in high yield; however, oligomerization of the HXT was observed by matrix‐assisted laser absorption ionization time‐of‐flight mass spectrometry (MALDI‐TOF MS). Oligomerization was eliminated by running the reaction with only 1.2 molar equivalents of HXT to PSLi and allowing the reaction to run for 15 min at ?10 °C in toluene. The resulting polymer exhibited high diene chain‐end functionality and no oligomerization was observed by MALDI‐TOF MS. ¹³C NMR spectroscopy and the attached‐proton test (APT), along with calculated chemical shifts, showed the presence of both the 1,2‐ and 1,4‐addition chain‐end structures. Further analysis by the reaction of the functional polymer with maleic anhydride indicated that 18 wt.‐% of the product was unreactive, either because of a 1,4‐addition chain‐end structure or a nonfunctional polymer. The structure of the maleic anhydride‐modified polymer was determined by MALDI‐TOF MS and ¹³C NMR spectroscopy. Preliminary work on the reactivity of the diene‐functionalized macromonomers was performed by the addition of a large excess of PSLi to a solution of macromonomer followed by characterization by size‐exclusion chromatography (SEC).

The formation of hexa‐1,3,5‐triene‐functionalized polystyrenes and their reaction with maleic anhydride.     

Synthesis of Ethylene/Acrylonitrile Composite Elastomers with Nanosized Polyacrylonitrile Domains Using α‐Dimine‐[N,N] Nickel Dichloride/EASC

A series of ethylene and acrylonitrile composite elastomers were prepared using (1,4‐bis(2,6diisopropylphenyl)‐acenaphtenediimine‐nickel(II))‐dichloride/ethylaluminum sesquichloride (EASC). The xylene‐soluble polymer fraction showed nitrile bands in infrared spectroscopy at 2 245 and 2 214 cm^?1 and polyacrylonitrile‐enriched structures were detected in the xylene‐insoluble fraction by¹H and ¹³C NMR. In addition, TEM detected nanosized polyacrylonitrile domains dispersed in the polyethylene matrix. Differential scanning calorimetry scans conducted from ?70 to 350 °C measured exothermic bands corresponding to the cyclization and aromatization of the nitrile groups dispersed in the polyethylene matrix.

     

Nickel‐Mediated Surface Grafting From Polymerization of α‐Amino Acid‐N‐Carboxyanhydrides

Summary: The feasibility of a living grafting from polymerization of α‐amino acid‐N‐carboxyanhydrides (NCA) from a surface using nickel initiators was shown. The polymerization has been carried out on commercially available polystyrene resins as spherical substrates in two different ways. Firstly L ‐glutamic acid was bound to the surface as γ‐ester via a UV‐labile linker and transferred into the NCA by treatment with triphosgene. The grafting from polymerization was then carried out as a “block copolymerization” by reaction of the surface bound NCA with an excess of the Ni amido‐amidate complex initiator and subsequent addition of free NCA to grow the polymer chain. By this procedure polymer was formed at the surface and can be isolated after photolysis of the linker. The characterization of the polymer by size exclusion chromatography indicates a living polymerization at the surface. The second approach employs N‐alloc‐amides at the surface to prepare an initiating Ni amido‐amidate complex directly at the surface. It can be shown that the latter approach is much more straightforward and gives smaller quantities of non‐tethered polypeptide.

Surface bound polypeptides were obtained by ring opening polymerization of α‐amino acid‐N‐carboxyanhydrides initiated by nickel amido‐amidate complexes installed at surfaces of commercially available polystyrene resins.     

Photodeformable Polymers: A New Kind of Promising Smart Material for Micro‐ and Nano‐Applications

Summary: Starting in the 1960s, several kinds of photodeformable polymers have been developed, such as monolayers, polymer gels, solid films and liquid‐crystalline elastomers with different photodeformation mechanisms. This field evolved slowly until recently when significant achievements have been made. Most recently, Lendlein and co‐workers have put forward another new concept – using photo‐crosslinking to prepare deformable polymers with various pre‐determined shapes (Nature 2005 , 434, 879). This highlight gives a general introduction into photodeformable polymers and brings forth future challenges.

A polymer film doped with SCAA molecules where (a) is the permanent shape, (b) is the temporary shape and (c) is the recovered shape.     

Studies on the Synthesis and Conductivity of a Novel Reactive Ladder‐Like Poly(β‐cyanoethylsilsesquioxane) and Poly[(β‐cyanoethylsilsesquioxane)‐co‐(β‐methylsilsesquioxane)]

Two novel reactive poly(β‐cyanoethylsilsesquioxane) ( CN‐T ) and poly[(β‐cyanoethylsilsesquioxane)‐co‐(β‐methylsilsesquioxane)] ( CN‐Me‐T ) have been synthesized successfully for the first time via stepwise coupling polymerization (SCP). A variety of characterization methods including FTIR, ¹H NMR, ²⁹Si NMR, X‐ray diffraction (XRD), differential scanning calorimetry (DSC) and vapor pressure osmometry (VPO) were combined to demonstrate that the structures of the title polymers possess ordered ladder‐like structures. As expected, the ionic conductivity of these polymers mixed homogeneously with lithium perchlorate reached 10^?6 S · cm^?1 at room temperature and obviously increased with the raise of temperature.

     

Synthesis of Hydroxyl‐Terminated Poly(vinylcarbazole‐ran‐styrene) Copolymers by Nitroxide‐Mediated Polymerization

A series of poly(vinylcarbazole‐ran‐styrene) copolymers with terminal hydroxyl groups were synthesized using nitroxide mediated polymerization (NMP) with the hydroxyl‐functional initiator VA‐086 and TEMPO as the mediator at 130 °C. Polymerizations were studied as a function of vinylcarbazole feed content, target molecular weight, and VA‐086/TEMPO ratio. The characterization of the copolymers was done by GPC and NMR. For feed concentrations of 40 mol‐% vinylcarbazole, copolymers with vinylcarbazole concentration up to 33 mol‐% could be obtained with narrow molecular weight distributions (PDI = 1.35) and exhibit pseudo‐“living” character up to conversions of about 20% if the target molecular weight was >100 kg · mol^?1. ¹H NMR indicated that the hydroxyl group was retained sufficiently with a functionality typically of about 0.7 hydroxyl groups per chain. Copolymers synthesized with higher vinylcarbazole feed content exhibited slower kinetics and were less controlled, resulting in much broader molecular weight distributions. The absence of control could be attributed to the absence of thermal initiation by vinylcarbazole which is advantageous toward controlling the radical concentration during the polymerization.

     

Block Copolymers from Organomodified Siloxane‐Containing Macroinitiators by Atom Transfer Radical Polymerization

Alternating copolymers of 1,3‐diisopropenylbenzene and 1,1,3,3‐tetramethyldisiloxane were synthesized by hydrosilylation–polyaddition. These linear copolymers were functionalized at both ends with 2‐bromoisobutyryl or benzyl chloride moieties. Subsequently, the obtained organomodified siloxane‐containing macroinitiators were successfully used for the preparation of ABA‐type block copolymers by atom transfer radical polymerization (ATRP) of styrene and tert‐butyl acrylate. The high chain‐end functionality of the macroinitiators was confirmed by ¹H NMR analysis of the macroinitiators and GPC measurements of the obtained ABA‐type block copolymers. The macroinitiator peaks disappeared in GPC traces after ATRP, and the obtained block copolymers showed a significantly narrower molecular‐weight distribution than the macroinitiators.

Synthesis of ABA‐type block copolymers by means of ATRP using organomodified siloxane‐containing, benzyl chloride functionalized macroinitiators.     

2D Self‐Assembly of an Amido‐Ended Hydrophilic Hyperbranched Polyester by Copper Ion Induction

The self‐assembly of an amido‐ended hydrophilic hyperbranched polyester (HTDA‐2) into ordered, compact, 2D, tree‐like structures with a diameter of over 500 μm and a trunk‐width of about 3–5 μm by the induction effect of cupric ions is presented. Influencing factors on the morphology of the self‐assemblies, including temperature, time, solvents, concentration, and humidity, investigated by polarizing optical microscopy (POM) and scanning electron microscopy (SEM), are discussed. The self‐assembly mechanism is analyzed by X‐ray photoelectron spectroscopy (XPS), X‐ray diffraction (XRD), SEM, and Fourier transform IR (FTIR) spectroscopy. A dimension (D_f) of about 1.50 for the perfect fractal behavior and the crystal behavior of the self‐assemblies are determined.

     

Click‐Chemistry: An Alternative Way to Functionalize Poly(2‐methyl‐2‐oxazoline)

CROP has been used to synthesize well‐defined POXZ with a monofunctional (iodomethane) or a bifunctional (1,3‐diiodopropane) initiator. POXZ has been functionalized with an azido group at one (α‐azido‐POXZ, = 3.58 × 10³ g · mol^?1) or both ends (α,ω‐azido‐POXZ, = 6.21 × 10³ g · mol^?1) of the macromolecular chain. The Huisgen 1,3‐dipolar cycloaddition has been investigated between azido‐POXZ and a terminal alkyne on a small or larger molecule (PEG). In each case, the click reaction has been successful and quantitative. In this way, different telechelic polymers (polymers bearing different functions such as acrylate, epoxide, or carboxylic acid) and block copolymers of POXZ and PEG have been prepared. The polymers have been characterized by means of FTIR, ¹H NMR, and SEC.

     

Morphology and Phase Characteristics of High‐Density Polyethylene Probed by NMR Spin Diffusion and Second Moment Analysis

Summary: A dipolar filter pulse sequence combined with cross‐polarization‐MAS is applied to characterize the phase distribution, morphology, and spin diffusion within a high‐density polyethylene sample. A new method to obtain quantitative ¹³C NMR by combining cross‐polarization‐MAS and spin diffusion NMR is presented. The derived crystallinity is consistent with the corresponding crystallinity obtained by ¹H NMR.

Illustration of the pulse sequence(s) applied in the present work.     

Proton‐Conducting Properties of Acid‐Doped Poly(glycidyl methacrylate)‐1,2,4‐Triazole Systems

1,2,4‐triazole‐functional PGMA polymers have been synthesized and their anhydrous proton‐conducting properties were investigated after doping with phosphoric acid and triflic acid. PGMA was prepared by solution polymerization and then modified with 1H‐1,2,4‐triazole (Tri) and 3‐amino‐1,2,4‐triazole (ATri). FT‐IR, ¹³C NMR and elemental analysis verify the high immobilization of the triazoles in the polymer chain. Phosphoric‐acid‐doped polymers showed lower T_g and higher proton conductivities. PGMA‐Tri 4 H₃PO₄ showed a maximum water‐free proton conductivity of approximately 10^?2 S · cm^?1 while that of PGMA‐ATri 2 H₃PO₄ was 10^?3 S · cm^?1. The structure and dynamics of the polymers were explored by ¹H MAS and ¹³C CP‐MAS solid‐state NMR.

     

Novel Supramolecular Polymers Based on Zinc‐Salen Chromophores for Efficient Light‐Emitting Diodes

Summary: A novel series of supramolecular polymers based on zinc‐salen chromophores were readily prepared via ligand‐metal coordination. These polymers were characterized by FT‐IR, NMR, GPC and elemental analysis. All the polymers were readily soluble in common organic solvents and had substantially good thermal properties. Cyclic voltammetry revealed they had LUMO energy levels ranging from −3.20 to −3.23 eV and HOMO energy levels ranging from −6.13 to −6.15 eV. The polymer films can emit strong green photoluminescence (PL) with relatively high quantum efficiencies of 42–51%. Light‐emitting diodes with the configuration ITO/PEDOT/polymer/BCP/Alq₃/LiF/Al were efficient green emitters, with maximum current efficiencies of 0.9–2.3 cd · A⁻¹. The preliminary EL results thus suggest that these polymers are potential candidates for efficient green emission in polymer LEDs.

Structures of polymers produced.     

Synthesis and Properties of Novel Fluorinated Poly(phenylene‐co‐imide)s

A new class of high‐performance materials, fluorinated poly(phenylene‐co‐imide)s, were prepared by Ni(0)‐catalytic coupling of 2,5‐dichlorobenzophenone with fluorinated dichlorophthalimide. The synthesized copolymers have high molecular weights ( = 5.74 × 10⁴–17.3 × 10⁴ g · mol^?1), and a combination of desirable properties such as high solubility in common organic solvent, film‐forming ability, and excellent mechanical properties. The glass transition temperature (T_gs) of the copolymers was readily tuned to be between 219 and 354 °C via systematic variation of the ratio of the two comonomers. The tough polymer films, obtained by casting from solution, had tensile strength, elongation at break, and tensile modulus values in the range of 66.7–266 MPa, 2.7–13.5%, and 3.13–4.09 GPa, respectively. The oxygen permeability coefficients ( ) and permeability selectivity of oxygen to nitrogen ( ) of these copolymer membranes were in the range of 0.78–3.01 barrer [1 barrer = 10^?10 cm³ (STP) cm/(cm² · s · cmHg)] and 5.09–6.25, respectively. Consequently, these materials have shown promise as engineering plastics and gas‐separation membrane materials.

     

Well‐Defined Miktocycle Eight‐Shaped Copolymers Composed of Polystyrene and Poly(ε‐caprolactone): Synthesis and Characterization

A series of well‐defined miktocycle number‐eight‐shaped copolymers composed of cyclic polystyrene (PS) and cyclic poly(ε‐caprolactone) (PCL) have been successfully synthesized by a combination of atom transfer radical polymerization (ATRP), ring‐opening polymerization (ROP), and “click” reaction. The synthesis involves three steps: 1) preparation of tetrafunctional initiator with two acetylene groups, one hydroxyl group and a bromo group; 2) preparation of two azide‐terminated block copolymers, N₃‐PCL‐(CH?C)₂‐PS‐N₃, with two acetylene groups anchored at the junction; and 3) intramolecular cyclization of the block copolymer through “click” reaction under high dilution. The ¹H NMR, FT‐IR, and gel permeation chromatography (GPC) techniques are applied to characterize the chemical structures of the resulting intermediates and the target polymers. Their thermal behavior is investigated by differential scanning calorimeter (DSC). The decrease in chain mobility of eight‐shaped copolymers restricts the crystallization of PCL.