Integrin alpha2beta1 plays a critical role in osteoblast response to micron-scale surface structure and surface energy of titanium substrates

Efforts to improve bone response to biomaterials have focused on ligands that bind α5β1 integrins. However, antibodies to α5β1 reduce osteoblast proliferation but do not affect differentiation when cells are grown on titanium (Ti). β1-silencing blocks the differentiation stimulus of Ti microtopography, suggesting that other β1 partners are important. Stably α2-silenced MG63 human osteoblast-like cells were used to test whether α2β1 specifically mediates osteoblast response to Ti surface micron-scale structure and energy. WT and α2-silenced MG63 cells were cultured on tissue culture polystyrene (TCPS) and Ti disks with different surface microtopographies: machined pretreatment (PT) surfaces [mean peak to valley roughness (R_a) < 0.02 μm], PT surfaces that were grit-blasted and acid-etched (SLA; R_a = 4 μm), and SLA with high surface energy (modSLA). Alkaline phosphatase (ALP), α2 and β1 mRNA, but not α5, αv, β3, type-I collagen, or osteocalcin, increased on SLA and modSLA at 6 days. α2 increased at 8 days on TCPS and PT, but remained unchanged on SLA and modSLA. α2-protein was reduced 70% in α2-siRNA cells, whereas α5-mRNA and protein were unaffected. α2-knockdown blocked surface-dependent increases in β1 and osteocalcin and decreases in cell number and increases in ALP and local factors typical of MG63 cells grown on SLA and modSLA [e.g., prostaglandin E₂, osteoprotegerin, latent and active TGF-β1, and stimulatory effects of 1α,25(OH)₂D₃ on these parameters]. This finding indicates that α2β1 signaling is required for osteoblastic differentiation caused by Ti microstructure and surface energy, suggesting that conclusions based on cell behavior on TCPS are not predictive of behavior on other substrates or the mechanisms involved.     

Increasing the Accuracy of Free-Form Surface Multiaxis Milling

This contribution deals with the accuracy of machining during free-form surface milling using various technologies. The contribution analyzes the accuracy and surface roughness of machined experimental samples using 3-axis, 3 + 2-axis, and 5-axis milling. Experimentation is focusing on the tool axis inclination angle—it is the position of the tool axis relative to the workpiece. When comparing machining accuracy during 3-axis, 3 + 2-axis, and 5-axis milling the highest accuracy (deviation ranging from 0 to 17 μm) was achieved with 5-axis simultaneous milling (inclination angles β_f = 10 to 15°, β_n = 10 to 15°). This contribution is also enriched by comparing a CAD (Computer Aided Design) model with the prediction of milled surface errors in the CAM (Computer Aided Manufacturing) system. This allows us to determine the size of the deviations of the calculated surfaces before the machining process. This prediction is analyzed with real measured deviations on a shaped surface—using optical three-dimensional microscope Alicona Infinite Focus G5.     

Study on the Formation Mechanism of Surface Adhered Damage in Ball-End Milling Ti6Al4V

Ball-end cutters are widely used for machining the parts of Ti-6Al-4V, which have the problem of poor machined surface quality due to the low cutting speed near the tool tip. In this paper, through the experiments of inclined surface machining in different feed directions, it is found that the surface adhered damages will form on the machined surface under certain tool postures. It is determined that the formation of surface adhered damage is related to the material adhesion near the cutting edge and the cutting-into/out position within the tool per-rotation cycle. In order to analyze the cutting-into/out process more clearly under different tool postures, the projection models of the cutting edge and the cutter workpiece engagement on the contact plane are established; thus, the complex geometry problem of space is transformed into that of plane. Combined with the case of cutting-into/out, chip morphology, and surface morphology, the formation mechanism of surface adhered damage is analyzed. The analysis results show that the adhered damage can increase the height parameters Sku, Sz, Sp, and Sv of surface topographies. Sz, Sp, and Sv of the normal machined surface without damage (Sku ≈ 3) are about 4–6, 2–3, and 2–3 μm, while Sz, Sp, and Sv with adhered damage (Sku > 3) can reach about 8–20, 4–14, and 3–6 μm in down-milling and 10–25, 7–18, and 3–7 μm in up-milling. The feed direction should be selected along the upper left (Q₂: β ∈ [0°, 90°]) or lower left (Q₃: β ∈ [90°, 180°]) to avoid surface adhered damage in the down-milling process. For up-milling, the feed direction should be selected along the upper right (Q₁: β ∈ (−90°, 0°]) or upper left (Q₂: β ∈ [0°, 90°)).     

Tribological Behavior of Reduced Graphene Oxide–Al2O3 Nanofluid: Interaction among Testing Force,Rotational Speed and Nanoparticle Concentration

The tribological properties of nanofluids are influenced by multiple factors, and the interrelationships among the factors are deserving of further attention. In this paper, response surface methodology (RSM) was used to study the tribological behavior of reduced graphene oxide–Al₂O₃ (rGO-Al₂O₃) nanofluid. The interaction effects of testing force, rotational speed and nanoparticle concentration on the friction coefficient (μ), wear rate (W_r) and surface roughness (R_a) of steel disks were investigated via the analysis of variance. It was confirmed that all the three input variables were significant for μ and W_r values, while testing force, nanoparticle concentration and its interaction with testing force and rotational speed were identified as significant parameters for R_a value. According to regression quadratic models, the optimized response values were 0.088, 2.35 × 10⁻⁷ mm³·N⁻¹·m⁻¹ and 0.832 μm for μ, W_r and R_a, which were in good agreement with the actual validation experiment values. The tribological results show that 0.20% was the optimum mass concentration which exhibited excellent lubrication performance. Compared to the base fluid, μ, W_r and R_a values had a reduction of approximately 45.6%, 90.3% and 56.0%. Tribochemical reactions occurred during the friction process, and a tribofilm with a thickness of approximately 20 nm was generated on the worn surface, consisting of nanoparticle fragments (rGO and Al₂O₃) and metal oxides (Fe₂O₃ and FeO) with self-lubrication properties.     

Investigations on the Effect of Layers’ Thickness and Orientations in the Machining of Additively Manufactured Stainless Steel 316L

Laser-powder bed fusion (L-PBF) process is a family of modern technologies, in which functional, complex (3D) parts are formed by selectively melting the metallic powders layer-by-layer based on fusion. The machining of L-PBF parts for improving their quality is a difficult task. This is because different component orientations (L-PBF-layer orientations) produce different quality of machined surface even though the same cutting parameters are applied. In this paper, stainless steel grade SS 316L parts from L-PBF were subjected to the finishing (milling) process to study the effect of part orientations. Furthermore, an attempt is made to suppress the part orientation effect by changing the layer thickness (LT) of the parts during the L-PBF process. L-PBF parts were fabricated with four different layer thicknesses of 30, 60, 80 and 100 μm to see the effect of the LT on the finish milling process. The results showed that the layer thickness of 60 μm has significantly suppressed the part orientation effect as compared to the other three-layer thicknesses of 30, 80 and 100 μm. The milling results showed that the three-layer thickness including 30, 80 and 100 μm presented up to a 34% difference in surface roughness among different part orientations while using the same milling parameters. In contrast, the layer thickness of 60 μm showed uniform surface roughness for the three-part orientations having a variation of 5–17%. Similarly, the three-layer thicknesses 30, 80 and 100 μm showed up to a 25%, 34% and 56% difference of axial force (Fa), feed force (Ff) and radial force (Fr), respectively. On the other hand, the part produced with layer thickness 60 μm showed up to 11%, 25% and 28% difference in cutting force components F_a, F_f and F_r, respectively. The three-layer thicknesses 30, 80 and 100 μm in micro-hardness were found to vary by up to 14.7% for the three-part orientation. Negligible micro-hardness differences of 1.7% were revealed by the parts with LT 60 μm across different part orientations as compared to 6.5–14% variations for the parts with layer thickness of 30, 80 and 100 μm. Moreover, the parts with LT 60 μm showed uniform and superior surface morphology and reduced edge chipping across all the part orientations. This study revealed that the effect of part orientation during milling becomes minimum and improved machined surface integrity is achieved if the L-PBF parts are fabricated with a layer thickness of 60 μm.     

Multi-Response Optimization of Abrasive Waterjet Machining of Ti6Al4V Using Integrated Approach of Utilized Heat Transfer Search Algorithm and RSM

Machining of Titanium alloys (Ti6Al4V) becomes more vital due to its essential role in biomedical, aerospace, and many other industries owing to the enhanced engineering properties. In the current study, a Box–Behnken design of the response surface methodology (RSM) was used to investigate the performance of the abrasive water jet machining (AWJM) of Ti6Al4V. For process parameter optimization, a systematic strategy combining RSM and a heat-transfer search (HTS) algorithm was investigated. The nozzle traverse speed (T_v), abrasive mass flow rate (A_f), and stand-off distance (S_d) were selected as AWJM variables, whereas the material removal rate (MRR), surface roughness (SR), and kerf taper angle (θ) were considered as output responses. Statistical models were developed for the response, and Analysis of variance (ANOVA) was executed for determining the robustness of responses. The single objective optimization result yielded a maximum MRR of 0.2304 g/min (at T_v of 250 mm/min, A_f of 500 g/min, and S_d of 1.5 mm), a minimum SR of 2.99 µm, and a minimum θ of 1.72 (both responses at T_v of 150 mm/min, A_f of 500 g/min, and S_d of 1.5 mm). A multi-objective HTS algorithm was implemented, and Pareto optimal points were produced. 3D and 2D plots were plotted using Pareto optimal points, which highlighted the non-dominant feasible solutions. The effectiveness of the suggested model was proved in predicting and optimizing the AWJM variables. The surface morphology of the machined surfaces was investigated using the scanning electron microscope. The confirmation test was performed using optimized cutting parameters to validate the results.     

Indium-Based Micro-Bump Array Fabrication Technology with Added Pre-Reflow Wet Etching and Annealing

Indium-based micro-bump arrays, among other things, are used for the bonding of infrared photodetectors and focal plane arrays. In this paper, several aspects of the fabrication technology of micrometer-sized indium bumps with a smooth surface morphology were investigated. The thermal evaporation of indium has been optimized to achieve ~8 μm-thick layers with a small surface roughness of R_a = 11 nm, indicating a high packing density of atoms. This ensures bump uniformity across the sample, as well as prevents oxidation inside the In columns prior to the reflow. A series of experiments to optimize indium bump fabrication technology, including a shear test of single columns, is described. A reliable, repeatable, simple, and quick approach was developed with the pre-etching of indium columns in a 10% HCl solution preceded by annealing at 120 °C in N₂.     

Wettability of Metal Surfaces Affected by Paint Layer Covering

The aim of the work was to quantify the surface wettability of metallic (Fe, Al, Cu, brass) surfaces covered with sprayed paints. Wettability was determined using the contact angle hysteresis approach, where dynamic contact angles (advancing Θ_A and receding Θ_R) were identified with the inclined plate method. The equilibrium, Θ_Y, contact angle hysteresis, CAH = Θ_A − Θ_R, film pressure, Π, surface free energy, γ_SV, works of adhesion, W_A, and spreading, W_S, were considered. Hydrophobic water/solid interactions were exhibited for the treated surfaces with the dispersive term contribution to γ_SV equal to (0.66–0.69). The registered 3D surface roughness profiles allowed the surface roughness and surface heterogeneity effect on wettability to be discussed. The clean metallic surfaces turned out to be of a hydrophilic nature (Θ_Y < 90°) with high γ_SV, heterogeneous, and rough with a large CAH. The surface covering demonstrated the parameters’ evolution, Θ_A↑, Θ_R↑, γ_SV↓, W_A↓, and W_S↓, corresponding to the surface hydrophobization and exhibiting base substratum-specific signatures. The dimensionless roughness fluctuation coefficient, η, was linearly correlated to CAH. The CAH methodology based on the three measurable quantities, Θ_A, Θ_R, and liquid surface tension, γ_LV, can be a useful tool in surface-mediated process studies, such as lubrication, liquid coating, and thermoflow.     

Alternating electron and proton transfer steps in photosynthetic water oxidation

Water oxidation by cyanobacteria, algae, and plants is pivotal in oxygenic photosynthesis, the process that powers life on Earth, and is the paradigm for engineering solar fuel–production systems. Each complete reaction cycle of photosynthetic water oxidation requires the removal of four electrons and four protons from the catalytic site, a manganese–calcium complex and its protein environment in photosystem II. In time-resolved photothermal beam deflection experiments, we monitored apparent volume changes of the photosystem II protein associated with charge creation by light-induced electron transfer (contraction) and charge-compensating proton relocation (expansion). Two previously invisible proton removal steps were detected, thereby filling two gaps in the basic reaction-cycle model of photosynthetic water oxidation. In the S₂ → S₃ transition of the classical S-state cycle, an intermediate is formed by deprotonation clearly before electron transfer to the oxidant (). The rate-determining elementary step (τ, approximately 30 µs at 20 °C) in the long-distance proton relocation toward the protein–water interface is characterized by a high activation energy (E_a = 0.46 ± 0.05 eV) and strong H/D kinetic isotope effect (approximately 6). The characteristics of a proton transfer step during the S₀ → S₁ transition are similar (τ, approximately 100 µs; E_a = 0.34 ± 0.08 eV; kinetic isotope effect, approximately 3); however, the proton removal from the Mn complex proceeds after electron transfer to . By discovery of the transient formation of two further intermediate states in the reaction cycle of photosynthetic water oxidation, a temporal sequence of strictly alternating removal of electrons and protons from the catalytic site is established.     

Change of Acoustic Emission Characteristics during Temperature Induced Transition from Twinning to Dislocation Slip under Compression in Polycrystalline Sn

In this study, acoustic emission (AE) measurements on polycrystalline tin as a function of temperature at different driving rates under compression were carried out. It is shown that there is a definite difference between the acoustic emission characteristics belonging to twinning (low temperatures) as well as to dislocation slip (high temperatures). The stress averaged values of the exponents of the energy probability density functions decreased from ε = 1.45 ± 0.05 (−60 °C) to ε = 1.20 ± 0.15 (50 °C) at a driving rate of ε=0.15 s−1, and the total acoustic energy decreased by three orders of magnitude with increasing temperature. In addition, the exponent γ in the scaling relation S_AE~D_AE^γ (S_AE is the area and D_AE is the duration) also shows similar temperature dependence (changing from γ = 1.78 ± 0.08 to γ = 1.35 ± 0.05), illustrating that the avalanche statistics belong to two different microscopic deformation mechanisms. The power law scaling relations were also analyzed, taking into account that the detected signal is always the convolution of the source signal and the transfer function of the system. It was obtained that approximate values of the power exponents can be obtained from the parts of the above functions, belonging to large values of parameters. At short duration times, the attenuation effect of the AE detection system dominates the time dependence, from which the characteristic attenuation time, τ_a, was determined as τ_a ≅ 70 μs.     

Integration of Fuzzy AHP and Fuzzy TOPSIS Methods for Wire Electric Discharge Machining of Titanium (Ti6Al4V) Alloy Using RSM

Titanium and its alloys exhibit numerous uses in aerospace, automobile, biomedical and marine industries because of their enhanced mechanical properties. However, the machinability of titanium alloys can be cumbersome due to their lower density, high hardness, low thermal conductivity, and low elastic modulus. The wire electrical discharge machining (WEDM) process is an effective choice for machining titanium and its alloys due to its unique machining characteristics. The present work proposes multi-objective optimization of WEDM on Ti6Al4V alloy using a fuzzy integrated multi-criteria decision-making (MCDM) approach. The use of MCDM has become an active area of research due to its proven ability to solve complex problems. The novelty of the present work is to use integrated fuzzy analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal situation (TOPSIS) to optimize the WEDM process. The experiments were systematically conducted adapting the face-centered central composite design approach of response surface methodology. Three independent factors—pulse-on time (T_on), pulse-off time (T_off), and current—were chosen, each having three levels to monitor the process response in terms of cutting speed (V_C), material removal rate (MRR), and surface roughness (SR). To assess the relevance and significance of the models, an analysis of variance was carried out. The optimal process parameters after integrating fuzzy AHP coupled with fuzzy TOPSIS approach found were T_on = 40 µs, T_off = 15 µs, and current = 2A.     

Investigation of Thermal Stability of Microstructure and Mechanical Properties of Bimetallic Fine-Grained Wires from Al–0.25%Zr–(Sc,Hf) Alloys

Thermal stability of composite bimetallic wires from five novel microalloyed aluminum alloys with different contents of alloying elements (Zr, Sc, and Hf) is investigated. The alloy workpieces were obtained by induction-casting in a vacuum, preliminary severe plastic deformation, and annealing providing the formation of a uniform microstructure and the nucleation of stabilizing intermetallide Al₃(Zr,Sc,Hf) nanoparticles. The wires of 0.26 mm in diameter were obtained by simultaneous deformation of the Al alloy with Cu shell. The bimetallic wires demonstrated high strength and improved thermal stability. After annealing at 450–500 °C, a uniform fine-grained microstructure formed in the wire (the mean grain sizes in the annealed Al wires are 3–5 μm). An increased hardness and strength due to nucleation of the Al₃(Sc,Hf) particles was observed. A diffusion of Cu from the shell into the surface layers of the Al wire was observed when heating up to 400–450 °C. The Cu diffusion depth into the annealed Al wire surfaces reached 30–40 μm. The maximum elongation to failure of the wires (20–30%) was achieved after annealing at 350 °C. The maximum values of microhardness (H_v = 500–520 MPa) and of ultimate strength (σ_b = 195–235 MPa) after annealing at 500 °C were observed for the wires made from the Al alloys alloyed with 0.05–0.1% Sc.     

Titanium Substratum Roughness as a Determinant of Human Gingival Fibroblast Fibronectin and α-Smooth Muscle Actin Expression

The most appropriate surface treatment to enhance gingival connective tissue formation on the abutment of dental implants remains undefined, with healing associated with a scar-like response. We have previously shown that topographies with an arithmetic average of the absolute profile height deviations (R_a) = 4.0 induces an anti-fibrotic phenotype in human gingival fibroblasts (HGFs) by causing nascent adhesion formation. With bacterial colonization considerations, we hypothesized that a lower R_a could be identified that would alter adhesion stability and promote a matrix remodeling phenotype. Focal adhesions (FAs) area decreased with increasing roughness, although no differences in cell attachment or proliferation were observed. Alpha smooth muscle actin (α-SMA) protein levels were significantly reduced on R_a = 3.0 and 4.0 vs. 0.1 (p < 0.05), with incorporation of α-SMA into stress fibers most prominent on R_a = 0.1. Fibronectin protein levels were reduced on 3.0 and 4.0 vs. 0.1 (p < 0.05), and R_a = 1.5 and deeper significantly altered fibronectin deposition. Addition of exogenous TGF-β3 increased HGF adhesion size on 0.1 surfaces, but not on any other topography. We conclude that R_a = 1.5 is sufficient to reduce adhesion size and inhibit α-SMA incorporation into stress fibers in HGFs, but 3.0 is required in the presence of exogenous TGF-β3. Our findings have implications for inhibiting fibrotic tissue formation surrounding percutaneous devices such as dental implants.     

Bioconjugation Strategy for Ceramic Membranes Decorated with Candida Antarctica Lipase B—Impact of Immobilization Process on Material Features

A strategy for the bioconjugation of the enzyme Candida antarctica lipase B onto titania ceramic membranes with varied pore sizes (15, 50, 150, and 300 kDa) was successfully performed. The relationship between the membrane morphology, i.e.,the pore size of the ceramic support, and bioconjugation performance was considered. Owing to the dimension of the enzyme (~33 kDa), the morphology of the ceramics allowed (50, 150, and 300 kDa) or did not allow (15 kDa) the entrance of the enzyme molecules into the porous structure. Such a strategy made it possible to better understand the changes in the material (morphology) and physicochemical features (wettability, adhesiveness, and surface charge) of the samples, which were systematically examined. The silane functionalization and enzyme immobilization were accomplished via the covalent route. The samples were characterized after each stage of the modification, which was very informative from the material point of view. As a consequence of the modification, significant changes in the contact angle, roughness, adhesion, and zeta potential were observed. For instance, for the 50 kDa membrane, the contact angle increased from 29.1 ± 1.5° for the pristine sample to 72.3 ± 1.5° after silane attachment; subsequently, it was reduced to 57.2 ± 1.5° after the enzyme immobilization. Finally, the contact angle of the bioconjugated membrane used in the enzymatic process rose to 92.9 ± 1.5°. By roughness (S_q) controlling, the following amendments were noticed: for the pristine 50 kDa membrane, S_q = 1.87 ± 0.21 µm; after silanization, S_q = 2.33 ± 0.30 µm; after enzyme immobilization, S_q = 2.74 ± 0.26 µm; and eventually, after the enzymatic process, S_q = 2.37 ± 0.27 µm. The adhesion work of the 50 kDa samples was equal to 136.41 ± 2.20 mN m⁻¹ (pristine membrane), 94.93 ± 2.00 mN m⁻¹ (with silane), 112.24 ± 1.90 mN m⁻¹ (with silane and enzyme), and finally, 69.12 ± 1.40 mN m⁻¹ (after the enzymatic process). The materials and physicochemical features changed substantially, particularly after the application of the membrane in the enzymatic process. Moreover, the impact of ceramic material morphology on the zeta potential value is here presented for the first time. With an increase in the ceramic support cut-off, the amount of immobilized lipase rose, but the specific productivity was higher for membranes possessing smaller pores, owing to the higher grafting density. For the enzymatic process, two modes of accomplishment were selected, i.e., stirred-tank and cross-flow. The latter method was characterized by a much higher effectiveness, with a resulting productivity equal to 99.7 and 60.3 µmol h⁻¹ for the 300 and 15 kD membranes, respectively.     

Investigation of Surface Integrity Induced by Various Finishing Processes of AISI 52100 Bearing Rings

Surface integrity induced by finishing processes significantly affects the functional performance of machined components. In this work, three kinds of finishing processes, i.e., precision hard turning, conventional grinding, and sequential grinding and honing, were used for the finish machining of AISI 52100 bearing steel rings. The surface integrity induced by these finishing processes was studied via SEM investigations and residual stress measurements. To investigate rolling contact fatigue performance, contact fatigue tests were performed on a twin-disc testing machine. As the main results, the SEM observations show that precision hard turning and grinding introduce microstructural alterations. Indeed, in precision hard turning, a fine white layer (<1 μm) is observed on the top surface, followed by a thermally affected zone in the subsurface, and in grinding only, a white layer with 5 μm thickness is observed. However, no microstructural changes are found after sequential grinding and honing processes. White layers induced by precision hard turning and grinding possess compressive residual stresses. Grinding and sequential grinding and honing processes generate similar residual stress distributions, which are maximum and compressive at the machined surface and tensile at the subsurface depth of 15 μm. Precision hard turning generates a “hook”-shaped residual stress profile with maximum compressive value at the subsurface depth and thus contributes as a prenominal factor to the obtainment of the longest fatigue life with respect to other finishing processes. Due to the high quality of surface roughness (Ra = 0.05 μm), honing post grinding improves the fatigue life of bearing rings by 2.6 times in comparison with grinding. Subsurface compressive residual stresses, as well as low surface roughness, are key parameters for extending bearing fatigue life.     

Anomalies in the Geometric Surface Structure of Shaped Elements Composed of Inconel 718 Alloy

This paper presents the results of investigation that was performed on shafts composed of Inconel 718. Tests were performed in dry and wet conditions. Cutting parameters, such as feed and depth of cut, were constant. The cutting speed was changed. The investigation was performed for various shaft shapes: cylindrical, taper 30°, taper 45°, and sphere. For that reason, the value of the angle between the machined surface and the cutting edge changed. The lowest values of the roughness parameters, Ra and Rz, were obtained for a larger value of the angle between the machined surface and cutting edge. The investigation showed that cutting speed, machining conditions (dry and wet machining), and the variable angle between the machined surface and the cutting edge influenced the surface roughness. Application of a higher cutting speed resulted in lower roughness values. Lower values of roughness parameters were obtained by wet machining.     

Effect of Heating Modes on Reactive Sintering of Ca3Co4O9 Ceramics

The traditional solid-state reaction method was employed to synthesize bulk calcium cobaltite (Ca349/Ca₃Co₄O₉) ceramics via ball milling the precursor mixture. The samples were compacted using conventional sintering (CS) and spark plasma sintering (SPS) at 850, 900, and 950 °C. The X-ray diffraction (XRD) pattern indicates the presence of the Ca349 phase for samples sintered at 850 and 900 °C. In addition, SPS fosters higher densification (81.18%) than conventional sintering (50.76%) at elevated sintering temperatures. The thermo-gravimetric analysis (TGA) and differential thermal analysis (DTA) performed on the precursor mixture reported a weight loss of ~25.23% at a temperature range of 600–820 °C. This current work aims to analyze the electrical properties (Seebeck coefficient (s), electrical resistivity (ρ), and power factor) of sintered samples as a function of temperature (35–500 °C). It demonstrates that the change in sintering temperature (conventional sintering) did not evince any significant change in the Seebeck coefficient (113–142 μV/K). However, it reported a low resistivity of 153–132 μΩ-m and a better power factor (82–146.4 μW/mK²) at 900 °C. On the contrary, the SPS sintered samples recorded a higher Seebeck coefficient of 121–181 μV/K at 900 °C. Correspondingly, the samples sintered at 950 °C delineated a low resistivity of 145–158 μΩ-m and a better power factor (97–152 μW/mK²).     

Cement-Based Thermoelectric Device for Protection of Carbon Steel in Alkaline Chloride Solution

The thermoelectric cement-based materials can convert heat into electricity; this makes them promising candidates for impressed current cathodic protection of carbon steel. However, attempts to use the thermoelectric cement-based materials for energy conversion usually results in low conversion efficiency, because of the low electrical conductivity and Seebeck coefficient. Herein, we deposited polyaniline on the surface of MnO₂ and fabricated a cement-based thermoelectric device with added PANI/MnO₂ composite for the protection of carbon steel in alkaline chloride solution. The nanorod structure (70~80 nm in diameter) and evenly dispersed conductive PANI provide the PANI/MnO₂ composite with good electrical conductivity (1.9 ± 0.03 S/cm) and Seebeck coefficient (−7.71 × 10³ ± 50 μV/K) and, thereby, increase the Seebeck coefficient of cement-based materials to −2.02 × 10³ ± 40 μV/K and the electrical conductivity of cement-based materials to 0.015 ± 0.0003 S/cm. Based on this, the corrosion of the carbon steel was delayed after cathodic protection, which was demonstrated by the electrochemical experiment results, such as the increased resistance of the carbon steel surface from 5.16 × 10² Ω·cm² to 5.14 × 10⁴ Ω·cm², increased charge transfer resistance from 11.4 kΩ·cm² to 1.98 × 10⁶ kΩ·cm², and the decreased corrosion current density from 1.67 μA/cm² to 0.32 μA/cm², underlining the role of anti-corrosion of the PANI/MnO₂ composite in the cathodic protection system.     

A Comparative Study on the Structure and Quality of SLM and Cast AISI 316L Samples Subjected to WEDM Processing

Additive manufacturing technologies are increasingly used in the production of semi-finished workpieces intended for further processing. This entails the need to investigate the machinability and final properties of such products. Comparative research on wire electrical discharge machining (WEDM) processes performed with two kinds of AISI 316L stainless steel workpieces is presented in this paper. The first workpiece was made by selective laser melting (SLM), while the second one was casting. Both working materials were cut with current values ranging from 8 to 72 amps. A comparison of roughness, structure and chemical composition of machined surfaces was performed between the two kinds of specimens. For the SLM sample, parameters of the cutting process that provide relatively low surface roughness (Ra ≤ 10 µm) with the simultaneous maximization of the process efficiency were determined. It was found that in the case of applying high current values (72 amp.), more favorable properties of the treated surface were obtained for the SLM sample than for the cast one.     

An attempt to distinguish between the actions of neuromuscular blocking drugs on the acetylcholine receptor and on its associated ionic channel

The effects of lobeline and tubocurarine on the voltage-clamped endplates of frog sartorius and cutaneous pectoris muscles were examined at room temperature (20-23°C). Like tubocurarine, lobeline causes nondepolarizing neuromuscular blockade. The half-time of decay (t_½) of endplate currents (e.p.c.s) recorded at a holding potential (V_m) of -90 mV was significantly shorter in endplates treated with lobeline (50 μM; mean t_½ ± SEM = 0.41 ± 0.02 ms) or tubocurarine (11.4 μM; t_½ = 0.64 ± 0.04 ms) than in those treated with Mg²⁺ (13 mM; t_½ = 1.39 ± 0.11 ms) or a low concentration of tubocurarine (3 μM; t_½ = 0.87 ± 0.05 ms). Similarly, lobeline (10 μM) shortened the t_½ of untreated miniature e.p.c.s by 35%; tubocurarine, however, abolished miniature e.p.c.s at the concentration required to observe its actions on e.p.c. decay kinetics. The t_½ of e.p.c.s recorded from preparations treated with Mg²⁺ (13 mM), tubocurarine at low concentrations (3 μM), or untreated miniature e.p.c.s was logarithmically related to V_m, being slower at more hyperpolarized values. By contrast, the t_½s of e.p.c.s recorded in either lobeline (50 μM) or tubocurarine (11.4 μM) were independent of voltage in the range -150 to -80 mV. The ability of lobeline to shorten t_½ and to remove the voltage dependence of t_½ was partially antagonized by Mg²⁺ (13 mM). As expected, when lobeline or tubocurarine was removed from the bath or when acetylcholine release from the motor nerve terminals was increased by 4-aminopyridine (20 μM) and Ca²⁺ (10 mM) (in the presence of lobeline or tubocurarine), the amplitude of e.p.c.s increased as a function of time. However, the t_½ of the decay phase of the e.p.c.s remained shortened (i.e., unaltered from the earlier treatment). These results suggest that both tubocurarine and lobeline have at least two distinct postjunctional actions including: (i) a block of the acetylcholine receptor and (ii) a block of the ionic channel associated with the acetylcholine receptor.