Electrospinning of nano/micro scale poly(L-lactic acid) aligned fibers and their potential in neural tissue engineering

Efficacy of aligned poly(l-lactic acid) (PLLA) nano/micro fibrous scaffolds for neural tissue engineering is described and their performance with random PLLA scaffolds is compared as well in this study. Perfectly aligned PLLA fibrous scaffolds were fabricated by an electrospinning technique under optimum condition and the diameter of the electrospun fibers can easily be tailored by adjusting the concentration of polymer solution. As the structure of PLLA scaffold was intended for neural tissue engineering, its suitability was evaluated in vitro using neural stem cells (NSCs) as a model cell line. Cell morphology, differentiation and neurite outgrowth were studied by various microscopic techniques. The results show that the direction of NSC elongation and its neurite outgrowth is parallel to the direction of PLLA fibers for aligned scaffolds. No significant changes were observed on the cell orientation with respect to the fiber diameters. However, the rate of NSC differentiation was higher for PLLA nanofibers than that of micro fibers and it was independent of the fiber alignment. Based on the experimental results, the aligned nanofibrous PLLA scaffold could be used as a potential cell carrier in neural tissue engineering.     

Material properties and osteogenic differentiation of marrow stromal cells on fiber-reinforced laminated hydrogel nanocomposites

The fibrils in the bone matrix are glued together by extracellular matrix proteins to form laminated structures (osteons) to provide elasticity and a supportive substrate for osteogenesis. The objective of this work was to investigate material properties and osteogenic differentiation of bone marrow stromal (BMS) cells seeded on osteon-mimetic fiber-reinforced hydrogel/apatite composites. Layers of electrospun poly(l-lactide) fiber mesh coated with a poly(lactide-co-ethylene oxide fumarate) (PLEOF) hydrogel precursor solution were stacked and pressed together, and crosslinked to produce a laminated fiber-reinforced composite. Hydroxyapatite (HA) nanocrystals were added to the precursor solution to produce an osteoconductive matrix for BMS cells. Acrylamide-terminated Arg–Gly–Asp (RGD) peptide (Ac-GRGD) was conjugated to the PLEOF/HA hydrogel phase to promote focal point adhesion of BMS cells. Laminates were characterized with respect to the Young’s modulus, degradation kinetics and osteogenic differentiation of BMS cells. The moduli of the laminates under dry and wet conditions were significantly higher than those of the fiber mesh and PLEOF/HA hydrogel, and within the range of values reported for wet human cancellous bone. At days 14 and 21, alkaline phosphatase (ALPase) activity of the laminates was significantly higher than those of the fiber mesh and hydrogel. Lamination significantly increased the extent of mineralization of BMS cells and laminates with HA and conjugated with RGD (Lam-RGD-HA) had 2.7-, 3.5- and 2.8-fold higher calcium content (compared to laminates without HA or RGD) after 7, 14 and 21 days, respectively. The Lam-RGD-HA group had significantly higher expression of osteopontin and osteocalcin compared to the hydrogel or laminates without HA or RGD, consistent with the higher ALPase activity and calcium content of Lam-RGD-HA. Laminated osteon-mimetic structures have the potential to provide mechanical strength to the regenerating region as well as supporting the differentiation of progenitor cells to the osteogenic lineage.     

Enhanced GLT-1 mediated glutamate uptake and migration of primary astrocytes directed by fibronectin-coated electrospun poly-l-lactic acid fibers

Bioengineered fiber substrates are increasingly studied as a means to promote regeneration and remodeling in the injured central nervous system (CNS). Previous reports largely focused on the ability of oriented scaffolds to bridge injured regions and direct outgrowth of axonal projections. In the present work, we explored the effects of electrospun microfibers on the migration and physiological properties of brain astroglial cells. Primary rat astrocytes were cultured on either fibronectin-coated poly-l-lactic acid (PLLA) films, fibronectin-coated randomly oriented PLLA electrospun fibers, or fibronectin-coated aligned PLLA electrospun fibers. Aligned PLLA fibers strongly altered astrocytic morphology, orienting cell processes, actin microfilaments, and microtubules along the length of the fibers. On aligned fibers, astrocytes also significantly increased their migration rates in the direction of fiber orientation. We further investigated if fiber topography modifies astrocytic neuroprotective properties, namely glutamate and glutamine transport and metabolism. This was done by quantifying changes in mRNA expression (qRT-PCR) and protein levels (Western blotting) for a battery of relevant biomolecules. Interestingly, we found that cells grown on random and/or aligned fibers increased the expression levels of two glutamate transporters, GLAST and GLT-1, and an important metabolic enzyme, glutamine synthetase, as compared to the fibronectin-coated films. Functional assays revealed increases in glutamate transport rates due to GLT-1 mediated uptake, which was largely determined by the dihydrokainate-sensitive GLT-1. Overall, this study suggests that aligned PLLA fibers can promote directed astrocytic migration, and, of most importance, our in vitro results indicate for the first time that electrospun PLLA fibers can positively modify neuroprotective properties of glial cells by increasing rates of glutamate uptake.     

Synergistic effects of electrospun PLLA fiber dimension and pattern on neonatal mouse cerebellum C17.2 stem cells

Topographical features, including fiber dimensions and pattern, are important aspects in developing fibrous scaffolds for tissue engineering. In this study aligned poly(l-lactide) (PLLA) fibers with diameters of 307 ± 47, 500 ± 53, 679 ± 72 and 917 ± 84 nm and random fibers with diameters of 327 ± 40, 545 ± 54, 746 ± 82 and 1150 ± 109 nm were obtained by optimizing the electrospinning parameters. We cultured neonatal mouse cerebellum C17.2 cells on the PLLA fibers. These neural stem cells (NSCs) exhibited significantly different growth and differentiation depending upon fiber dimension and pattern. On aligned fibers cell viability and proliferation was best on 500 nm fibers, and reduced on smaller or larger fibers. However, on random fibers cell viability and proliferation was best with the smallest (350 nm) and largest (1150 nm) diameter fibers. Polarized and elongated cells were orientated along the fiber direction on the aligned fibers, with focal contacts bridging the cell body and aligned fibers. Cells of spindle and polygonal morphologies were randomly distributed on the random fibers, with no focal contacts observed. Moreover, longer neurites were obtained on the aligned fibers than random fibers within the same diameter range. Thus, the surface topographic morphologies of fibrous scaffolds, including fiber pattern, dimensions and mesh size, play roles in regulating the viability, proliferation and neurite outgrowth of NSCs. Nevertheless, our results indicated that aligned 500 nm fiber are most promising for fine tuning the design of a nerve scaffold.     

Directed differentiation and neurite extension of mouse embryonic stem cell on aligned poly(lactide) nanofibers functionalized with YIGSR peptide

End-functional PLLA nanofibers were fabricated into mats of random or aligned fibers and functionalized post-spinning using metal-free “click chemistry” with the peptide Tyr-Ile-Gly-Ser-Arg (YIGSR). Fibers that were both aligned and functionalized with YIGSR were found to significantly increase the fraction of mouse embryonic stem cells (mESC) expressing neuron-specific class III beta-tubulin (TUJ1), the level of neurite extension and gene expression for neural markers compared to mESC cultured on random fiber mats and unfunctionalized matrices. Precise functionalization of degradable polymers with bioactive peptides created translationally-relevant materials that capitalize on the advantages of both synthetic and natural systems, while mitigating the classic limitations of each.     

Influence of the structure of poly (L-lactic acid) electrospun fibers on the bioactivity of endothelial cells: proliferation and inflammatory cytokines expression

Electrospinning has been used to fabricate random and aligned poly (L-lactic acid) (PLLA) fibers with three kinds of diameter under optimal conditions. The main purpose of this paper was to investigate the influence of the diameter and orientation of fibers on the bioactivity of endothelial cells, especially on the inflammatory cytokines expression. The morphology of electrospun fibers and the cells on the fibers after 3 and 6 days culture were observed by scanning electron microscopy. Also the cell proliferation activity and cell cycle were tested and the results showed that the random fibers were more favorable for endothelial cells growth. The effect of PLLA film (served as a control) and six kinds of PLLA fibers mats on the inflammatory cytokines expression after cells incubated for 2 and 4 days were investigated. It was concluded that there was more intense inflammatory cytokines expression by cells on flat PLLA film than that on electrospun fiber mats. Also the fiber diameter has greater effect on the activity and inflammatory cytokines expression of endothelial cells than the fiber orientation, in which fibers with smaller size has weaker inflammatory reaction.     

Nanofiber size-dependent sensitivity of fibroblast directionality to the methodology for scaffold alignment

The sensitivity of fibroblast guidance on directional cues provided by aligned nanofibers is studied for scaffolds of successively smaller fiber sizes (740 ± 280, 245 ± 85, 140 ± 40, and 80 ± 10 nm) fabricated using mandrel and electrical alignment methodologies for electrospun nanofibers (～10° angular deviation (AD)), as well as nanoimprint methodologies for perfectly aligned fibers (0° AD). On aligned scaffolds of large fibers (～740 nm) cell directionality closely follows the underlying fibers, irrespective of the alignment method. However, on mandrel aligned scaffolds of successively smaller fibers the cell directionality exhibits greater deviations from the underlying fiber alignment due to the higher likelihood of interaction of cell lamellipodia with multiple, rather than single, nanofibers. Using electrically aligned scaffolds, fibroblast directionality deviations can be maintained in the range of nanofiber alignment deviation for fiber sizes down to ～100 nm. This improvement in cell guidance is attributed to molecular scale directional adhesion cues for cell receptors, which occur within electrically aligned scaffolds due to fiber polarization parallel to the geometric alignment axis of the nanofiber under the modified electric field during electrospinning. While fibroblast directionality is similar on electrically aligned vs. nanoimprinted scaffolds for fiber sizes >100 nm, cell directionality is influenced more strongly by the perfect alignment cues of the latter on ～100 nm fiber scaffolds. The scaffold alignment methodology is hence highly significant, especially for tissue engineering applications requiring sub-100 nm aligned fibers.     

Nebulized solvent ablation of aligned PLLA fibers for the study of neurite response to anisotropic-to-isotropic fiber/film transition (AFFT) boundaries in astrocyte–neuron co-cultures

Developing robust in vitro models of in vivo environments has the potential to reduce costs and bring new therapies from the bench top to the clinic more efficiently. This study aimed to develop a biomaterial platform capable of modeling isotropic-to-anisotropic cellular transitions observed in vivo, specifically focusing on changes in cellular organization following spinal cord injury. In order to accomplish this goal, nebulized solvent patterning of aligned, electrospun poly-l-lactic acid (PLLA) fiber substrates was developed. This method produced a clear topographic transitional boundary between aligned PLLA fibers and an isotropic PLLA film region. Astrocytes were then seeded on these scaffolds, and a shift between oriented and non-oriented astrocytes was created at the anisotropic-to-isotropic fiber/film transition (AFFT) boundary. Orientation of chondroitin sulfate proteoglycans (CSPGs) and fibronectin produced by these astrocytes was analyzed, and it was found that astrocytes growing on the aligned fibers produced aligned arrays of CSPGs and fibronectin, while astrocytes growing on the isotropic film region produced randomly-oriented CSPG and fibronectin arrays. Neurite extension from rat dissociated dorsal root ganglia (DRG) was studied on astrocytes cultured on anisotropic, aligned fibers, isotropic films, or from fibers to films. It was found that neurite extension was oriented and longer on PLLA fibers compared to PLLA films. When dissociated DRG were cultured on the astrocytes near the AFFT boundary, neurites showed directed orientation that was lost upon growth into the isotropic film region. The AFFT boundary also restricted neurite extension, limiting the extension of neurites once they grew from the fibers and into the isotropic film region. This study reveals the importance of anisotropic-to-isotropic transitions restricting neurite outgrowth by itself. Furthermore, we present this scaffold as an alternative culture system to analyze neurite response to cellular boundaries created following spinal cord injury and suggest its usefulness to study cellular responses to any aligned-to-unorganized cellular boundaries seen in vivo.     

Electrospun Poly(Hydroxybutyrate-co-Hydroxyvalerate) Fibrous Membranes Consisting of Parallel-Aligned Fibers or Cross-Aligned Fibers: Characterization and Biological Evaluation

Poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) fibrous membranes consisting of parallel-aligned fibers or cross-aligned fibers were fabricated through electrospinning with the help of a rotating cylinder as fiber collector and auxiliary electrodes, and their application as tissue-engineering scaffolds was assessed. First, these membranes were characterized in terms of fiber diameter, spacing between adjacent aligned fibers or interstitial pore diameter, degree of fiber alignment, wettability and tensile properties. Then, human osteoblast-like cells (SaOS-2) were seeded and cultured on these membranes for up to 14 days. The cell morphology and proliferation were evaluated at different cell culture times. Membranes consisting of random fibers or parallel-aligned fibers were obtained when the rotational speed of the cylinder was 500 rpm or 3000 rpm, respectively. A very high rotational speed of 15 000 rpm resulted in the formation of parallel-aligned fibers having low or no spacing between the aligned fibers. Membranes consisting of cross-aligned fibers were made at the rotational speed of 3000 rpm and micrometer-sized fiber spacing was observed in these membranes. The alignment of fibers led to enhanced wettability of fibrous membranes. Tensile testing revealed that the parallel-aligned fibrous membranes were strong in the longitudinal direction but weak in the transverse direction. The cross-aligned fibrous membranes did not exhibit particularly weak tensile properties in any direction. In vitro biological evaluation showed that SaOS-2 cells spread randomly on membranes of random fibers but elongated in membranes of aligned fibers. All membranes supported cell proliferation in spite of the differences in cell morphology.     

Biomaterial guides for lymphatic endothelial cell alignment and migration

Axillary dissection during breast cancer surgery produces extensive lymphatic vessel damage that often leads to lifelong secondary lymphedema of the arm. We have developed a biodegradable material conduit for lymphatic vessel reconstruction where fibers electrospun along the conduit lumen promote endothelial cell alignment and migration in vitro. The diameter and density of the electrospun fibers were optimized for cell migration and direction on two-dimensional substrates by seeding human lymphatic endothelial cells (LECs) onto aligned fibers of varying diameters and densities, randomly oriented fibers, and film substrates with no fibers. We found that LECs became aligned in the fiber direction, with cells seeded on the randomly oriented fibers becoming oriented in random directions, whereas cells seeded on the highly aligned fibers became highly aligned. Cell migration was dependent upon fiber alignment and density, with optimal migration found on 1300 nm diameter aligned fibers of low density. Blood endothelial cells seeded on the fibers exhibited similar behavior as the LECs. Fiber alignment was preserved upon rolling the two-dimensional substrate into the tubular geometry of a lymphatic vessel. The data suggest that aligned electrospun fibers may promote endothelial migration across the conduit in a manner that is independent of lymphatic growth factors.     

Varying the diameter of aligned electrospun fibers alters neurite outgrowth and Schwann cell migration

Aligned, electrospun fibers have shown great promise in facilitating directed neurite outgrowth within cell and animal models. While electrospun fiber diameter does influence cellular behavior, it is not known how aligned, electrospun fiber scaffolds of differing diameter influence neurite outgrowth and Schwann cell (SC) migration. Thus, the goal of this study was to first create highly aligned, electrospun fiber scaffolds of varying diameter and then assess neurite and SC behavior from dorsal root ganglia (DRG) explants. Three groups of highly aligned, electrospun poly-l-lactic acid (PLLA) fibers were created (1325 + 383 nm, large diameter fibers; 759 + 179 nm, intermediate diameter fibers; and 293 + 65 nm, small diameter fibers). Embryonic stage nine (E9) chick DRG were cultured on fiber substrates for 5 days and then the explants were stained against neurofilament and S100. DAPI stain was used to assess SC migration. Neurite length and SC migration distance were determined. In general, the direction of neurite extension and SC migration were guided along the aligned fibers. On the small diameter fiber substrate, the neurite length was 42% and 36% shorter than those on the intermediate and large fiber substrates, respectively. Interestingly, SC migration did not correlate with that of neurite extension in all situations. SCs migrated equivalently with extending neurites in both the small and large diameter scaffolds, but lagged behind neurites on the intermediate diameter scaffolds. Thus, in some situations, topography alone is sufficient to guide neurites without the leading support of SCs. Scanning electron microscopy images show that neurites cover the fibers and do not reside exclusively between fibers. Further, at the interface between fibers and neurites, filopodial extensions grab and attach to nearby fibers as they extend down the fiber substrate. Overall, the results and observations suggest that fiber diameter is an important parameter to consider when constructing aligned, electrospun fibers for nerve regeneration applications.     

Nanofiber matrices promote the neuronal differentiation of human embryonic stem cell-derived neural precursors in vitro

The potential of human embryonic stem (ES) cells as experimental therapies for neuronal replacement has recently received considerable attention. In view of the organization of the mature nervous system into distinct neural circuits, key challenges of such therapies are the directed differentiation of human ES cell-derived neural precursors (NPs) into specific neuronal types and the directional growth of axons along specified trajectories. In the present study, we cultured human NPs derived from the NIH-approved ES line BGO1 on polycaprolactone fiber matrices of different diameter (i.e., nanofibers and microfibers) and orientation (i.e., aligned and random); fibers were coated with poly-L-ornithine/laminin to mimic the extracellular matrix and support the adhesion, viability, and differentiation of NPs. On aligned fibrous meshes, human NPs adopt polarized cell morphology with processes extending along the axis of the fiber, whereas NPs on plain tissue culture surfaces or random fiber substrates form nonpolarized neurite networks. Under differentiation conditions, human NPs cultured on aligned fibrous substrates show a higher rate of neuronal differentiation than other matrices; 62% and 86% of NPs become TUJ1 (+) early neurons on aligned micro- and nanofibers, respectively, whereas only 32% and 27% of NPs acquire the same fate on random micro- and nanofibers. Metabolic cell activity/viability studies reveal that fiber alignment and diameter also have an effect on NP viability, but only in the presence of mitogens. Our findings demonstrate that fibrous substrates serve as an artificial extracellular matrix and provide a microenviroment that influences key aspects of the neuronal differentiation of ES-derived NPs.     

Platelet-derived growth-factor-releasing aligned collagen–nanoparticle fibers promote the proliferation and tenogenic differentiation of adipose-derived stem cells

In order to enhance the healing potential of an injured tendon, we have prepared a novel biomimetic aligned collagen–nanoparticle (NP) composite fiber using an electrochemical process. The aligned collagen–NP composite fiber is designed to affect the cellular activity of adipose-derived stem cells (ADSCs) through two different ways: (i) topographic cues from the alignment of collagen fibril and (ii) controlled release of platelet-derived growth factors (PDGFs) from the NPs. PDGF released from collagen–NP fibers significantly enhanced the proliferation of ADSCs when tested for up to 7 days. Moreover, compared to random collagen fibers with PDGFs, aligned collagen–NP fibers significantly promoted the desirable tenogenic differentiation of ADSCs, as evidenced by an increased level of tendon markers such as tenomodulin and scleraxis. On the other hand, no undesirable osteogenic differentiation, as measured by the unchanged level of alkaline phosphatase and osteocalcin, was observed. Together, these results indicate that the aligned collagen–NP composite fiber induced the tenogenic differentiation of ADSCs through both a topographic cue (aligned collagen fibril) and a chemical cue (PDGF released from NPs). Thus, our novel aligned collagen–NP composite fiber has a significant potential to be used for tendon tissue engineering and regeneration.     

In vitro cell performance on hydroxyapatite particles/poly(L-lactic acid) nanofibrous scaffolds with an excellent particle along nanofiber orientation

Highly porous hydroxyapatite (HA)/poly(L-lactide) (PLLA) nanofibrous scaffolds were prepared by incorporating needle-shaped nano- or micro-sized HA particles into PLLA nanofibers using electrospinning. The scaffolds had random or aligned fibrous assemblies and both types of HA particles were perfectly oriented along the fiber long axes. The biocompatibility and cell signaling properties of these scaffolds were evaluated by in vitro culture of rat osteosarcoma ROS17/2.8 cells on the scaffold surface. Cell morphology, viability and alkaline phosphatase (ALP) activity on each scaffold were examined at different time points. The HA/PLLA scaffolds exhibited higher cell viability and ALP activity than a pure PLLA scaffold. In addition, micro-sized HA particles supported cell proliferation and differentiation better than nano-sized ones in random scaffolds through a 10 day culture period and in aligned scaffolds at an early culture stage. The fibrous assembly of the scaffold had a pronounced impact on the morphology of the cells in direct contact with the scaffold surface, but not on cell proliferation and differentiation. Thus, HA/PLLA nanofibrous scaffolds could be good candidates for bone tissue engineering.     

Aligned electrospun nanofibers specify the direction of dorsal root ganglia neurite growth

Nerve injury, a significant cause of disability, may be treated more effectively using nerve guidance channels containing longitudinally aligned fibers. Aligned, electrospun nanofibers direct the neurite growth of immortalized neural stem cells, demonstrating potential for directing regenerating neurites. However, no study of neurite guidance on these fibers has yet been performed with primary neurons. Here, we examined neurites from dorsal root ganglia explants on electrospun poly-L-lactate nanofibers of high, intermediate, and random alignment. On aligned fibers, neurites grew radially outward from the ganglia and turned to follow the fibers upon contact. Neurite guidance was robust, with neurites never leaving the fibers to grow on the surrounding cover slip. To compare the alignment of neurites to that of the nanofiber substrates, Fourier methods were used to quantify the alignment. Neurite alignment, however striking, was inferior to fiber alignment on all but the randomly aligned fibers. Neurites on highly aligned substrates were 20 and 16% longer than neurites on random and intermediate fibers, respectively. Schwann cells on fibers assumed a very narrow morphology compared to those on the surrounding coverslip. The robust neurite guidance demonstrated here is a significant step toward the use of aligned, electrospun nanofibers for nerve regeneration. (c) 2007 Wiley Periodicals, Inc. J Biomed Mater Res, 2007.     

Enhanced differentiation of human neural crest stem cells towards the Schwann cell lineage by aligned electrospun fiber matrix

Human pluripotent stem cell-derived neural crest stem cells (NCSCs) provide a promising cell source for generating Schwann cells in the treatment of neurodegenerative diseases and traumatic injuries in the peripheral nervous system. Influencing cell behavior through a synthetic matrix topography has been shown to be an effective approach to directing stem cell proliferation and differentiation. Here we have investigated the effect of nanofiber topography on the differentiation of human embryonic stem cell-derived NCSCs towards the Schwann cell lineage. Using electrospun fibers of different diameters and alignments we demonstrated that aligned fiber matrices effectively induced cell alignment, and that fiber matrices with average diameters of 600 nm and 1.6 μm most effectively promoted NCSC differentiation towards the Schwann cell lineage compared with random fibers and two-dimensional tissue culture plates. More importantly, human NCSCs that were predifferentiated in Schwann cell medium for 2 weeks exhibited higher sensitivity to the aligned fiber topography than undifferentiated NCSCs. This study provides an efficient protocol for Schwann cell derivation by combining an aligned nanofiber matrix and an optimized differentiation medium, and highlights the importance of matching extrinsic matrix signaling with cell intrinsic programming in a temporally specific manner.     

Self-standing aligned fiber scaffold fabrication by two photon photopolymerization

Development of materials and fabrication techniques lead the growth of three-dimensional cell culture matrices in biomedical engineering. In this work, we present a method for fabricating self-standing fiber scaffolds by two-photon polymerization induced by a femtosecond laser. The aligned fibers are 330 μm long with a diameter of 6–9 μm. Depending on the pitch of the aligned fibers, various cell morphologies are distinguished via three-dimensional images. Furthermore, the morphologies of fibroblast cells (NIH-3T3) and epithelial cells (MDCK) on the fiber scaffolds are studied to show the effect of high curvature (3–4.5 μm radii) on cell morphology. NIH-3T3 cells that contain straight pattern of actin microfilament bundles are extended and partly wrap single fibers or tend to reside between fibers. On the other hand, MDCK cells that contain circular pattern of actin microfilament bundles cover the fiber peripheral surface exhibiting high aspect ratio elongation. These results indicate that cell morphology on fiber scaffolds is influenced by the pattern of actin microfilament bundles.     

Aligned and random nanofibrous substrate for the in vitro culture of Schwann cells for neural tissue engineering

The current challenge in peripheral nerve tissue engineering is to produce an implantable scaffold capable of bridging long nerve gaps that will produce results similar to autograft without requiring the harvest of autologous donor tissue. Aligned and random polycaprolactone/gelatin (PCL/gelatin) nanofibrous scaffolds were fabricated for the in vitro culture of Schwann cells that assist in directing the growth of regenerating axons in nerve tissue engineering. The average fiber diameter attained by electrospinning of polymer blend (PCL/gelatin) ranged from 232 ± 194 to 160 ± 86 nm with high porosity (90%). Blending PCL with gelatin resulted in increased hydrophilicity of nanofibrous scaffolds and yielded better mechanical properties, approaching those of PCL nanofibers. The biocompatibility of fabricated nanofibers was assessed for culturing and proliferation of Schwann cells by MTS assay. The results of the MTS assay and scanning electron microscopy confirmed that aligned and random PCL/gelatin nanofibrous scaffolds are suitable substrates for Schwann cell growth as compared to PCL nanofibrous scaffolds for neural tissue engineering.     

Static magnetic field exposure promotes differentiation of osteoblastic cells grown on the surface of a poly-<Emphasis Type="SmallCaps">l</Emphasis>-lactide substrate

This study investigated the effects of static magnetic fields on the differentiation of MG63 cells cultured on the surface of poly-l-lactide (PLLA) substrates. The cells were continuously exposed to a 4,000 Gauss-static magnetic field (SMF) for 5 days. The proliferation effects of the SMF were measured by MTT assay. Morphologic changes and extracellular matrix release were observed by scanning electron microscopy. The effects of the SMF on alkaline phosphatase activity levels were compared between exposed and unexposed cells. The SMF-exposed cells exhibited decreased MTT values after 1 and 3 days of culture. In addition, SMF exposure promoted the expression of extracellular matrix in MG63 cells on the PLLA substrate. After 1 day, the alkaline phosphatase-specific activity of SMF-exposed MG63 cells was significantly increased (P < 0.05) with a ratio of 1.5-fold. These results show that MG63 cells, seeded on a PLLA disc and treated with SMF, had a more differentiated phenotype.