Curing potential and color stability of different resin-based luting materials

PurposeTo determine the curing potential and color stability of resin-based luting materials for aesthetic restorations.Material and MethodsFour resin-based luting agents were tested: traditional dual-activated resin cement (RelyX ARC, ARC), amine-free dual-activated resin cement (RelyX Ultimate, ULT), light-activated resin cement (RelyX Veneer, VEN), and pre-heated restorative resin composite (Filtek Supreme, PHC). Degree of C = C conversion was determined by infrared spectroscopy (n = 3) with direct light exposure or with interposition of 1.5-mm-thick ceramic (e.max Press HT) between the luting material and light. The curing potential considered the ratio between these two scenarios. Color difference (n = 6) was determined by CIELAB (ΔE_ab) and CIEDE2000 (ΔE₀₀) methods, by spectrophotometer measurements made 24 h after photoactivation and 90 days after storage in water. Data was submitted to ANOVA and Tukey’s test (α = 0.05).ResultsThe luting agents affected both conversion and color stability. With ceramic, ARC produced the highest conversion among the tested groups (75 ± 1%) and the pre-heated composite (PHC) the lowest one (51 ± 3%), but the curing potential was similar for all materials. ULT produced lower ΔE_ab than ARC. PHC presented the lowest color difference when considered both CIELAB and CIE2000 methods (ΔE_ab 2.1 ± 0.4; ΔE₀₀ 1.6 ± 0.2).SignificanceAll luting strategies presented high curing potential. Amine-free dual-activated material was able to reduce color difference than that formulated with the amine component. Pre-heated composite produced the least color variation after storage.     

Comparison of various 3D printed and milled PAEK materials: Effect of printing direction and artificial aging on Martens parameters

ObjectivesThe aim of this study was to investigate the effect of artificial aging on the Martens parameters of different 3D printed and milled polyaryletherketon (PAEK) materials.MethodsIn total 120 specimens of 4 different polyetheretherketon (PEEK) materials (Essentium PEEK, KetaSpire PEEK MS-NT1, VICTREX PEEK 450 G and VESTAKEEP i4 G) were additively manufactured via fused layer manufacturing (FLM) in either horizontal or vertical directions (n = 15 per group). 75 specimens were milled out of prefabricated PAEK blanks from the materials breCAM.BioHPP, Dentokeep, JUVORA Dental Disc 2 and Ultaire AKP ( = 15 per group). Martens hardness (HM), indentation hardness (H_IT) and indentation modulus (E_IT) were determined initially and longitudinally after thermocycling (5−55 °C, 10,000x) and autoclaving (134 °C, 2 bar). In each case, the surface topography of the specimens was examined for modifications using a light microscope.Data were analysed with Kolmogorov-Smirnov test, univariate ANOVA followed by post-hoc Scheffé test with partial eta squared (η_p²), Kruskal–Wallis-, Mann–Whitney-U-, Friedman- and Wilcoxon-Test. A value of p < 0.05 was considered as significant.ResultsMilled specimens showed higher Martens parameters than printed ones (p < 0.001). Artificial aging had a negative effect on the measured parameters (p < 0.001). Horizontally printed specimens presented higher Martens parameters than vertically printed ones, regardless of material and aging process (p < 0.001). Essentium PEEK and breCAM.BioHPP showed the highest and VICTREX PEEK 450G as well as Ultaire AKP the lowest values of all investigated PAEK materials initially, after thermocycling and after autoclaving (p < 0.001). Microscopic examinations showed that artificial aging did not cause any major modifications of the materials.SignificanceAdditively manufactured PEEK materials showed lower Martens parameters than milled ones, whereas horizontally printed specimens presented higher values than vertically printed ones. Artificial aging had a negative effect on the Martens parameters, but not on the surface topography.     

Influence of TiO2 nanoparticles on the optical properties of resin composites

ObjectivesTo determine the influence of titanium dioxide (TiO₂) nanoparticle addition on the opalescence, color, translucency and fluorescence of experimental resin composites.MethodsA light curing resin matrix was made by mixing 60 wt.% Bis-GMA and 40 wt.% TEGDMA. Silane coated glass filler (mean particle size: 1.55 μm) was added in the ratio of 50 wt.% of the resin composites. A fluorescent whitening agent was also added (0.05 wt.%). TiO₂ nanoparticles (<40 nm) were added with the concentrations of 0, 0.1, 0.25 and 0.5 wt.%. Reflected and transmitted colors of 1 and 2 mm thick specimens were measured relative to the illuminant D65 with reflection spectrophotometers. Opalescence parameter (OP), color difference (ΔE*_ab), translucency parameter (TP), fluorescence parameter (FL), and fluorescence and opalescence spectra were calculated.ResultsFor the 1 mm thick specimens measured with 3 mm × 8 mm rectangular aperture, when the concentration of TiO₂ increased from 0% to 0.5%, OP increased from 2.4 to 18.0, TP decreased from 35.4 to 13.1, and fluorescence spectra remained unchanged. Color difference between these specimens was in the range of 3.4–6.6 ΔE*_ab units. OP values were significantly influenced by the thickness of the specimens and the configuration of the spectrophotometers (p < 0.05).SignificanceAddition of TiO₂ nanoparticles significantly increased the opalescence of resin composites while leaving the fluorescence spectra unchanged; however, it significantly decreased the translucency and also changed the color (p < 0.05). Resin composites with 0.1–0.25% TiO₂ nanoparticle would simulate the opalescence of human enamel.     

Effect of changes in sintering parameters on monolithic translucent zirconia

ObjectivesAim of this study was to evaluate the effect of different sintering parameters on color reproduction, translucency and biaxial flexural strength of monolithic zirconia.MethodsTranslucent zirconia discs having 15 mm diameter, 1 mm thickness, and shade A3 were milled and divided according to the sintering temperatures (1460 °C, 1530 °C, and 1600 °C) into three groups (n = 30). Each group was later divided into three subgroups (n = 10) according to the sintering holding time (1, 2, and 4 h). Easyshade spectrophotometer (Vita, Bad Säckingen, Germany) was used to obtain the ΔE between the specimens and the shade A3. Mean ΔE values below 3.0 were considered “clinically imperceptible”, ΔE values between 3.0 and 5.0 were considered “clinically acceptable” and ΔE values above 5.0 were considered “clinically unacceptable”. Contrast ratio (CR) was obtained after comparing the reflectance of light through the specimens over black and white background. Biaxial flexural strength was tested using the piston-on-three balls technique in a universal testing machine.ResultsMean ΔE results ranged from 4.4 to 2.2. Statistically significant decrease in the Delta E was observed as the sintering time and temperature increased. CR decreased from 0.75 to 0.68 as the sintering time and temperature increased. No significant change in the biaxial flexural strength was observed.SignificanceSintering zirconia using long cycles and high temperatures will result in reduction of ΔE and CR. Biaxial flexural strength is not affected by changes in the evaluated sintering parameters.     

In Vitro Dental Discoloration Provoked by Intracanal Calcium Silicate-based Dressing Used for Regenerative Endodontic Procedures: An One-year Spectrometric Analysis

IntroductionRegenerative endodontic procedures provide conditions for the continuity of apical formation and increase of the dentin wall thickness, being a useful technique to resume root development of necrotic teeth with incomplete apex. This study aimed to evaluate the coronal discoloration promoted by a new intracanal calcium silicate-based dressing and compare it with other intracanal dressings used in regenerative endodontic procedures.MethodsSixty bovine incisors were prepared to simulate teeth with incomplete apexes and divided according to the intracanal dressing used: triple antibiotic paste—double antibiotic paste—DAP, calcium hydroxide associated with 2% chlorhexidine gel, calcium hydroxide associated with saline solution, and Bio-C Temp. As control, no dressing was performed. The intracanal dressings remained in the simulated root canal for 21 days. Luminosity (ΔL) and color difference (ΔE_ab and ΔE₀₀) were evaluated using long-term (1 year) spectrophotometric analysis. The results were analyzed using the ANOVA test with Tukey post hoc with a significance of 5%.ResultsTriple antibiotic paste showed the highest values of ΔE_ab and ΔE₀₀ and lowest values of ΔL (P < .05). Bio-C Temp showed higher ΔE_ab than the other groups from 6 months (P < .05), higher ΔE₀₀ and lower ΔL after 1 year (P < .05).ConclusionsBio-C Temp induced noticeable coronary discoloration after the 1-year analysis.     

Influence of pigments and opacifiers on color stability of silicone maxillofacial elastomer

ObjectivesTo determine the effects of opacifiers and silicone pigments on the color stability of silicone A-2000 maxillofacial prosthetic elastomers subjected to artificial aging.MethodsSeventy-five groups (n = 5) were made by various combinations (5%, 10%, and 15%) of four dry earth opacifiers (Georgia kaolin, Gk; calcined kaolin, Ck; Artskin white, Aw; titanium white dry pigment, Td); and 1 silicone pigment white (Sw) with one of 5 silicone pigments (no pigment (control), red (Pr), yellow (Py), burnt sienna (Po), and a mixture of Pr + Py + Po). A reflection spectrophotometer was used for color measurements. Color differences (ΔE*) between baseline and after an energy exposure of 450 kJ/m² in an artificial aging chamber were calculated. A ΔE* = 3.0 was used as 50:50% acceptability threshold in result interpretation, while ΔE* = 1.1 was used as 50:50% perceptibility threshold. Means were compared by Fisher's PLSD intervals at the 0.05 level of significance. Color differences after aging were subjected to three-way analysis of variance.ResultsYellow ochre mixed with all opacifiers at all intervals had increased ΔE* values significantly from 0.7–2.1 up to 3.8–10.3. When mixed groups were considered, at 5%, Gk exhibited the smallest color changes, followed by Td < Aw = Sw < Ck, respectively. At 10%, Aw < Td < Gk < Sw = Ck. At 15%, Td < Aw < Gk = Sw < Ck (< indicates p < 0.0001 and = indicates p > 0.05). The smallest color differences, observed for opacifier groups, were recorded for Gk at 5%, and Td and Aw at 10% and 15%. Overall, 15% Td exhibited the smallest, whereas 5% Ck exhibited the most pronounced color change after artificial aging. All ΔE* values were below the 50:50% acceptability threshold, indicating acceptable color stability. Color differences for 10% and 15% of Aw and Td were below 50:50% perceptibility thresholds, indicating excellent color stability.ConclusionSilicone pigments mixed with 10% and 15% Artskin white and titanium white dry pigment opacifiers protected silicone A-2000 from color degradation over time. Yellow silicone pigment significantly affected color stability of all opacifiers especially silicone pigment white and calcined kaolin.     

Does translucency influence cure efficiency and color stability of resin-based composites?

Objective

To determine if material’s translucency influences the cure efficiency and color stability of resin-based composites (RBCs).

Effect of denture cleansers on physical properties of heat-polymerized acrylic resin

PurposeThis study aimed to measure the color change, surface roughness and flexural strength of heat-polymerized acrylic resin after its immersion in denture cleansers, simulating a 180-day use.MethodsThirty disk-shaped (15 mm × 4 mm) and 30 rectangular samples (65 mm × 10 mm × 3.3 mm) were prepared from heat-polymerized acrylic resin and immersed in Corega Tabs, Bony Plus, and distilled water. Color measurements (ΔE) were determined by a portable colorimeter. A surface analyzer was used to measure the roughness before and after immersion (ΔRa). The flexural strength (S) was measured using a 3-point bending test. The ΔE values were submitted to statistical analysis by the Kruskal–Wallis test, followed by Dunn's Multiple Comparisons test. The ΔRa and S values were submitted to statistical analysis by ANOVA, followed by a Student–Newman–Keuls test (α = .05).ResultsThe color changes were significantly higher for the Corega Tabs than for the control group. The mean ΔE values quantified by the National Bureau of Standards (NBS) were classified as Trace (0.0–0.5). The Bony Plus group had significantly higher surface roughness than the other groups. Corega Tabs and Bony Plus groups presented lower flexural strength than the control group.ConclusionsAlthough the color changes after the immersion in denture cleansers were clinically insignificant, the Corega Tabs group showed higher color differences. The Bony Plus group showed significantly increased surface roughness. Both effervescent tablets Corega Tabs and Bony Plus significantly diminished the flexural strength of the acrylic resin.     

Effect of fabrication techniques on the optical properties of zirconia-based systems

Statement of problemHow the optical properties of zirconia restorations are affected by their differing processing techniques is unclear.PurposeThe purpose of this in vitro study was to evaluate the effects of 5 different fabrication techniques on the optical properties of zirconia-based systems, including the color difference between the corresponding shades (ΔE1_ab, ΔE₀₀), translucency parameter, opalescence parameter, and fluorescence (ΔE1_ab-FL).Material and methodsSixty zirconia disks (IPS e.max ZirCAD) were prepared (0.5 ±0.01mm thick) and veneered by using different techniques (n=15): Group L – layering with fluorapatite ceramic; Group P – pressing with fluorapatite ceramic; Group CB – veneered with pressing followed by layering technique; Group CO – digitally veneered with lithium disilicate glass-ceramic; and Group FZ – prepared from monolithic zirconia (inCoris TZI) (n=15). All the specimens were set to 1.5 ±0.02 mm in thickness. Color measurements were made with a spectrophotometer. Data were statistically analyzed with 1-way ANOVA and the Tukey honestly significant difference, Kruskal-Wallis, Bonferroni (α=.05), Pearson, and Spearman correlation tests (α=.01).ResultsSignificant differences were found among the groups for all the optical parameters (P<.05). All the groups showed color differences higher than the perceptibility and acceptability thresholds for ΔE1_ab and ΔE₀₀, except the P and FZ groups that showed values lower than the acceptability threshold (ΔE1_ab<2.7). Translucency parameter, opalescence parameter, and ΔE1_ab-FL values ranged between 5.77 and 9.95, between 4.72 and 7.07, and between 1.93 and 3.14, respectively. Strong positive correlations were found between ΔE1_ab and ΔE₀₀, as well as between translucency parameter and opalescence parameter (P<.001).ConclusionsThe optical properties of the zirconia-based systems were significantly affected by the fabrication techniques even when the same nominal shade was used. Therefore, the color reproduction, translucence, opalescence, and fluorescence of the selected materials should be considered for acceptable color matching.     

The effect of surface defects in early caries assessment using quantitative light-induced fluorescence (QLF) and micro-digital-photography (MDP)

ObjectivesThe purpose of this study was to consider the impact of surface defects on quantitative light-induced fluorescence (QLF) and micro-digital-photography (MDP) measures, in relationship to lesion depth.MethodsSimulated enamel carious lesions were developed on 45 extracted human teeth. Images of each tooth were captured with both QLF and MDP. The teeth were sectioned and lesion depth was measured with polarized light microscopy (PLM). Pearson correlations were computed using data from the 27 lesions which did not have surface loss, and then separately based upon the 18 lesions which did display surface loss. MDP variables ΔR and ΔX measure reflected light, whereas QLF variables ΔF and ΔQ measure fluorescence.ResultsA strong correlation was identified between lesion depth and ΔF (r = ?0.765, p < 0.0001), and ΔQ (r = ?0.827, p < 0.0001) on intact lesions while a weak but suggestive, although non-significant, correlation was identified between average lesion depth and ΔR (r = 0.369, p = 0.059) and ΔX (r = 0.595, p = 0.0011). However, the corresponding correlation was not statistically significant, when lesions with surface loss were considered for QLF and MDP measures.ConclusionsQLF measures ΔF and ΔQ were strongly correlated with lesion depth in lab-simulated lesions with no surface loss, but not among lesions with surface defects. The two MDP-associated measures, ΔR and ΔX, could not be said to differ significantly when lesions with and without surface defects were compared with lesion depth. Because intact lesions can be remineralized, accurate assessment of their status is imperative for caries treatment.Clinical significanceDental caries is still widely prevalent today. We now know that with early stage detection, remineralization can be accomplished. Being able to identify dental caries in its reversible stage (before physical surface loss) is paramount for the clinician to be able to treat the disease non-invasively.     

Clinical evaluation of perceptibility of color differences between natural teeth and all-ceramic crowns

ObjectivesColor matching still remains as one of the most challenging tasks in clinical dentistry. With the advancement of intraoral color matching instruments the importance of the development of color thresholds becomes increasingly important. The objective of this study was to set a gold standard for the color difference (ΔE) at which all-ceramic crowns cannot be distinguished from natural teeth.MethodAll-ceramic crowns with a zirconia coping (LAVA, 3M ESPE, St. Paul, MN, USA) and layered porcelain (Cerabien CZR, Noritake, Nagoya, Japan) fabricated to match contralateral maxillary central incisors were assessed by experienced observers. Eleven all-ceramic crowns (AC) were assessed as “excellent/perfect matches;” these crowns were then measured using a spectrophotometer and compared to their natural counterparts. Unrestored natural maxillary teeth (NT) were compared to unrestored contralateral teeth in 22 subjects. Six areas were measured in both groups to determine color differences (ΔE*).ResultsMean ΔE* value between the restorations and natural teeth was 1.6. Mean ΔE* between contralateral natural teeth was 0.9. Incisal areas of natural teeth exhibited greater differences in color than other compared areas.ConclusionA ΔE* = 1.6 represented the color difference that could not be detected by the human eye.     

Reflectance and color prediction of dental material monolithic samples with varying thickness

ObjectiveTo assess accuracy of reflectance reconstruction and color estimation of different dental materials with varying thicknesses using Principal Component Analysis (PCA).MethodA1, A2, A3, A3.5, B2, C2 and D2 shades and 5 thicknesses (within 0.5–2.5 mm range) of Vita Suprinity (VS-PC) and Vitapan Dentine (VD), were used. Reflectance measurements were performed over black background using a non-contact spectroradiometer with CIE 45^°∕0^° geometry. A PCA based algorithm was proposed to reconstruct spectral data and color of samples, using both extrapolation and interpolation approaches. Root Mean Square Error (RMSE), Goodness of Fit (GFC), correlation coefficient (R²) as well as ΔE₀₀ with corresponding 50:50% acceptability and perceptibly thresholds (AT and PT) were used as performance assessment.ResultsThe interpolation approach provided an average RMSE = 0.01 and GFC > 0.999 when comparing predicted and measured spectral reflectances for both materials, while for the extrapolation approach RMSE = 0.02 and GFC > 0.999. Interpolation approach also resulted in lower overall mean color difference ΔE₀₀ = 0.8 (ΔE₀₀ = 0.9 for VS-PC and ΔE₀₀ = 0.7 for VD), while using extrapolation approach resulted in higher overall mean color difference ΔE₀₀ = 1.6, although below the AT (ΔE₀₀ = 1.8 for VS-PC and ΔE₀₀ = 1.5 for VD). Correlation values between predicted and measured spectral reflectances of R² = 0.987 and R² = 0.993 were globally obtained for VS-PC and VD, respectively.SignificanceThe proposed PCA-based algorithm is able to efficiently predict reflectance spectrum and color of monolithic samples of different dental materials with varying thickness. It can be used to optimize dental materials manufacturing processes and to improve chromatic accuracy of clinical dental restorations.     

Frequency of MCP-1 (rs1024611) and CCR2 (rs1799864) gene polymorphisms and its effect on gene expression level in patients with AgP

ObjectiveTo identify the genetic risk markers of aggressive periodontitis (AgP), researchers focus on genetic components that regulate the immune response. Therefore the purpose of this study was to investigate genetic impact of monocyte chemoattractant protein (MCP)-1–2518 A/G and CC chemokine receptor 2 (CCR2) −190 G/A gene polymorphisms on AgP susceptibility and the effect of this polymorphism on MCP-1 gene expression in patients with AgP.Material and methodsA total of 215 subjects, 108 AgP and 107 periodontally healthy (H) were recruited in this cross-sectional study (NCT02817568). Gene polymorphisms of MCP-1–2518 A/G and CCR2–190 G/A were analyzed by a standard polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) assay. MCP-1 messenger (m) RNA expression was measured using quantitative real-time (RT)-PCR in peripheral blood leukocytes from 26 AgP and 16 H controls. Threshold cycles (C_t) values were obtained from the RT-PCR analysis based on SYBR Green detection and data was normalized via ΔC_t.ResultsThere were no differences between AgP and H groups with regard to MCP-1 and CCR2 genotype distribution and allele frequencies (p > 0.05). In contrast, the MCP-1 mRNA expression levels were higher in homozygous “AA” control subjects than having G⁺ genotype and AA homozygous AgP patients.ConclusionsIt can be concluded that MCP-1 and CCR2 polymorphisms are not associated with AgP in Turkish population. Although in AgP patients, there was AA genotype with MCP-1 mRNA expression it can be speculated that gene expression levels in peripheral blood may not reflect the cytokine/chemokine levels of local tissues.     

Self-cured resin modified by quaternary ammonium methacrylates and chlorhexidine: Cytotoxicity,antimicrobial, physical,and mechanical properties

ObjectiveTo evaluate the addition of dimethylaminohexadecyl methacrylate (DMAHDM) and chlorhexidine diacetate on cytotoxicity, antimicrobial activity, physical, and mechanical properties of a self-cured resin.Methods132 disk-shaped and 48 rectangular specimens were divided into four experimental groups as described: Control Group (CG – no addition), dCHX (1%), DMAHDM (5%), and DMAHDM + dCHX (5% + 1%). The biofilm viability, flexural strength (FS - ISO 20795-1:2013), surface roughness (SR), and color stability (ΔE) were analyzed after being stored for 4 weeks in distilled water and immersed for 72 h in coffee. Cytotoxicity was measured after 24 h, 3, and 7 days of elution using an MTT test on L929 cells (ISO 10993-5:2009). SR and ΔE were measured by a contact profilometer and a spectrophotometer using the CIELab parameter. Data were submitted to ANOVA and Bonferroni’s/Tukey’s tests (p ≤ 0.05).ResultsSignificant antimicrobial activity against Streptococcus mutans and Candida albicans was detected in all groups when compared to the CG (p < 0.05). Only the dCHX group, in 24 h of elution, demonstrated no cytotoxicity effects. There was a statistical difference for FS on the tested groups (p < 0.05). No differences were detected in the initial roughness’ measurements among the groups (p > 0.05). However, after storage and immersion in coffee, the groups containing DMAHDM presented with rougher surfaces and significantly lower color stability compared to the control (p < 0.05).SignificanceThe addition of dCHX and DMAHDM in self-cured resin presented antimicrobial properties; however, cytotoxicity, physical, and mechanical properties were compromised.     

Influence of photoinitiator system and nanofiller size on the optical properties and cure efficiency of model composites

ObjectiveTo establish the relationship between photoinitiator system and nanofiller size on the optical properties and cure efficiency of model composites.MethodsModel composites based on BisGMA/TEGDMA (60:40 mol%) were loaded with 40 wt% of 7 nm or 16 nm-sized filler particles. One of the following photoinitiator systems was added: camphorquinone (CQ) associated with an amine (EDMAB), monoacylphosphine oxide (TPO), or bysacylphosphine oxide (BAPO). The optical properties of disk-shaped specimens were measured 24 h after curing and repeated after storage in water for 90 days and coffee for 15 days. A large spectrum LED unit (Bluephase G2, Ivoclar Vivadent) was used for photoactivation. CIE L*a*b* parameters, color difference (ΔE), and translucency parameter (TP) were calculated. Knoop hardness readings were taken at top and bottom composite surfaces. Cure efficiency was determined by bottom/top hardness ratio. Data were statistically analyzed at α = 0.05 significance level.ResultsComposites formulated with 16 nm particles had higher CIE L* than those with 7 nm particles in all storage conditions. BAPO-based composites generally had lower CIE a* than the other composites. The group TPO + 16 nm before storage and all groups with 16 nm-sized particles after storage had lower CIE b* (i.e. lower degree of yellowing) than the other groups. TPO-based materials had higher color stability. The cure efficiency was not significantly affected by photoinitiator system or particle size. CQ + 7 nm had the lowest and BAPO + 16 nm the highest hardness values.SignificanceCombination of photoinitiator system and filler particle size might affect the optical properties of composites, with low influence on cure efficiency.     

Color change of some aesthetic dental materials: Effect of immersion solutions and finishing of their surfaces

ObjectivesThe purpose of this research was to evaluate the color change of five aesthetic dental materials, before and after immersion in distilled water and blue food color solution for 7 and 21 days, and to study the effect of finishing the surfaces on any color change.MethodsDisc shaped samples of five types of light curing composite (A2) (n = 10 samples/composite) were prepared and all samples were light-cured with a Plasma Arc light cure unit for ten seconds. One side of each sample disc was finished and polished with a Super-Snap system all samples. After 24 h, color measurements of each sample were conducted using a digital spectrophotometer. Five sample discs from each composite group were immersed in 30 ml of food color solution for 7 and 21 days, while the remaining five sample discs were immersed in 30 ml of distilled water as a control. Color measurements were repeated for all samples at 7 and 21 days after immersion. The color changes were statistically analyzed using t-tests within the same group. A result was considered statistically significant at α = 0.05.ResultsThe color differences (ΔE) ranged from 0.4 to 4.66 and statistically significant differences on the finished and unfinished surfaces were observed after immersion in the food color solution for 7 days. No significant differences were found in any group after immersion in the food color solution for 21 days. The Tetric EvoCeram and Arabesk groups showed less color differences after 7 and 21 days than other composites.ConclusionFinished composite surfaces showed less coloration than unfinished surfaces after 7 days, but all surfaces (finished and unfinished) were highly colored for all composite types after 21 days.     

Translucency,flexural strength,fracture toughness,fracture load of 3-unit FDPs,Martens hardness parameter and grain size of 3Y-TZP materials

ObjectiveThis investigation tested pre-shaded 3Y-TZP materials on optical, mechanical and structural properties and calculated correlations between these properties.MethodsSeven A2-shaded 3Y-TZP zirconia materials were investigated on translucency (T) via UV–vis-spectrophotometer, fracture load of 3-unit FDPs (FL), biaxial flexural strength (FS), Chevron-Notch Beam (CNB), fracture toughness (K_IC) and Martens parameter (hardness: HM and indentation modulus: E_IT). FL, FS and K_IC were measured in a universal testing machine. The grain size was evaluated by scanning electron microscopy (SEM). Data was analyzed using one-way ANOVA followed by post hoc Scheffé, Kruskal–Wallis-, Mann–Whitney-U- and Pearson-test (p < 0.05).ResultsFor translucency, negative correlations were found with results of facture load (R = −0.444, p < 0.001) and K_IC (R = −0.503, p < 0.001). While a positive correlation was found between translucency and flexural strength (R = 0.238, p = 0.019), between fracture load and E_IT (R = 0.227, p < 0.029), between fracture load and K_IC (R = 0.362, p < 0.001) as well as between fracture load and the grain size (R = 0.598, p = 0.007). While the grain size positively correlated with E_IT (R = 0.534, p = 0.017) as well as E_IT with HM (R = 0.720, p < 0.001).SignificanceDespite of being based on the same raw material, tested zirconia materials significantly differed regarding optical, mechanical (except biaxial flexural strength and Martens hardness) and structural properties. Materials with highest optical properties were those with lowest mechanical properties (CER, COP).     

The influence of printing angle on color and translucency of 3D printed resins for dental restorations

ObjectivesTo evaluate the influence of printing orientation on color and translucency of 3D printing restorative resins.MethodsFour 3D printing resin systems in the available shades (DFT-Detax Freeprint Temp- A1, A2,A3; FP-Formlabs Permanent Crown- A2,A3,B1,C2; FT- Formlabs Temporary CB- A2,A3,B1,C2; GCT-GC Temporary- Light, Medium) were evaluated. Three samples (10×10×1.2 mm) from each material were printed at two different printing orientations (0° and 90°) and polished to 1.00 ± 0,01 mm of thickness. Spectral reflectance was measured against black background using a calibrated spectroradiometer, CIE D65 standard illuminant and the 45°/0°geometry. Color and translucency differences were evaluated using CIEDE2000 metric (ΔE₀₀) and 50:50% perceptibility (PT₀₀ and TPT₀₀) and acceptability (AT₀₀ and TAT₀₀) thresholds.ResultsIn general, color changes due to printing orientation at (0° and 90°) were mainly produced by ΔL* or ΔC* . ΔE₀₀ were above PT₀₀ for all DFT shades, FP-B1, FP-C2, FT-A2 and FT-B1. Only for DFT-1, ΔE₀₀ was above AT₀₀. ΔRTP₀₀ values were above TPT₀₀ for DFT-A1, DFT-A3, FP-B1 and FT-B1, but lower than TAT₀₀. The direction of the changes in translucency (ΔRTP₀₀) depends on the material and shade.SignificanceThe selection of building orientation (0° and 90°) for the 3D printed resins influence the visual color and translucency and therefore their esthetic appearance. These aspects should be considered when printing dental restorations using the evaluated materials.     

Effects of duration of whitening strip treatment on tooth color: A randomized,placebo-controlled clinical trial

ObjectivesA randomized, double-blind, placebo-controlled clinical trial was conducted to evaluate efficacy and safety of 6% hydrogen peroxide whitening strip used twice daily over an extended, 6-week period.MethodsAfter informed consent, 40 eligible adults were randomly assigned to 6% hydrogen peroxide whitening strips (Crest Whitestrips, The Procter & Gamble Company, USA) or placebo strips without peroxide. Treatment was twice daily for 30 min, and response was evaluated biweekly after initial (Week 2) and extended (Weeks 4 and 6) use. Tooth color was measured under standardized lighting conditions using digital image analysis, and safety was assessed from clinical examination and interview. Whitening was measured using data derived from digital images taken at baseline compared to post-treatment, with outcomes reported using the CIELAB color notation system. Analysis of variance and covariance were used to assess initial response, and repeated measures regression analysis was used to model color change during sustained use.ResultsForty subjects (25–58 years old) started the study. At baseline, L* ranged from 68.0 to 76.8, a* ranged from 8.0 to 11.8, and b* ranged from 16.4 to 23.1. Groups differed significantly (p < 0.001) on all color parameters at Week 2 and thereafter, favoring the 6% hydrogen peroxide strips. Week 2 adjusted means ± SE were ?2.1 ± 0.2 for Δb* and 1.9 ± 0.2 for ΔL* for the peroxide group compared to ?0.3 ± 0.2 for Δb* and 0.4 ± 0.2 for the placebo group. With sustained use (Weeks 2–6), the slope for the peroxide strip was estimated as ?0.3 for Δb* and +0.2 for ΔL* per week, with both slopes differing significantly from zero (p < 0.0001), while slopes for the placebo strip were not significant (p = 0.22) and nearly zero. Treatment was generally well tolerated, with adverse events confined to symptoms only.ConclusionsTwice-daily use of 6% hydrogen peroxide whitening strips resulted in teeth becoming lighter and less yellow versus baseline and placebo during initial 2-week use, with no evidence of placebo response during sustained (Weeks 2–6) use.