Shear Wave Elastography Quantifies Stiffness in Ex Vivo Porcine Artery with Stiffened Arterial Region

Five small porcine aortas were used as a human carotid artery model, and their stiffness was estimated using shear wave elastography (SWE) in the arterial wall and a stiffened artery region mimicking a stiff plaque. To optimize the SWE settings, shear wave bandwidth was measured with respect to acoustic radiation force push length and number of compounded angles used for motion detection with plane wave imaging. The mean arterial wall and simulated plaque shear moduli varied from 41 ± 5 to 97 ± 10 kPa and from 86 ± 13 to 174 ± 35 kPa, respectively, over the pressure range 20–120 mmHg. The results revealed that a minimum bandwidth of approximately 1500 Hz is necessary for consistent shear modulus estimates, and a high pulse repetition frequency using no image compounding is more important than a lower pulse repetition frequency with better image quality when estimating arterial wall and plaque stiffness using SWE.     

Sources of Variability in Shear Wave Speed and Dispersion Quantification with Ultrasound Elastography: A Phantom Study

There is a growing interest in quantifying shear-wave dispersion (SWD) with ultrasound shear-wave elastography (SWE). Recent studies suggest that SWD complements shear-wave speed (SWS) in diffuse liver disease diagnosis. To accurately interpret these metrics in clinical practice, we analyzed the impact of operator-dependent acquisition parameters on SWD and SWS measurements. Considered parameters were the acquisition depth, lateral position and size of the region of interest (ROI), as well as the size of the SWE acquisition box. Measurements were performed using the Canon Aplio i800 system (Canon Medical Systems, Otawara, Tochigi, Japan) and four homogeneous elasticity phantoms with certified stiffness values ranging from 3.7 to 44 kPa. In general, SWD exhibited two to three times greater variability than SWS. The acquisition depth was the main variance-contributing factor for both SWS and SWD, which decayed significantly with depth. The lateral ROI position contributed as much as the acquisition depth to the total variance in SWD. Locations close to the initial shear-wave excitation pulse were more robust to biases because of inaccurate probe–phantom coupling. The size of the ROI and acquisition box did not introduce significant variations. These results suggest that future guidelines on multiparametric elastography should account for the depth- and lateral-dependent variability of measurements.     

Heel Pad Stiffness in Plantar Heel Pain by Shear Wave Elastography

The goal of the study was to evaluate the reliability of supersonic shear wave elastography in measuring heel pad stiffness and the change in heel pad stiffness in patients with plantar heel pain. In the reliability test involving 12 normal participants, each heel pad was tested six times in succession, and adequate reliability was reflected in the intraclass correlation coefficients (0.95, 0.93 and 0.96 for the microchambers, macrochambers and bulk heel pad, respectively). In the clinical assessment involving 20 normal participants and 16 unilateral plantar heel pain patients, diseased heel pads (86.8 ± 22.9, 36.8 ± 7.7 and 46.6 ± 10.9 kPa for the microchambers, macrochambers and bulk heel pad, respectively) were significantly stiffer than unaffected heel pads (66.8 ± 14.1, 25.2 ± 5.7, 34.2 ± 6.6 kPa) and those of normal participants (60.9 ± 11.4, 26.3 ± 6.1, 31.8 ± 6.3 kPa), suggesting that the heel pad with plantar heel pain was associated with loss of elasticity.     

Evaluation of Post-Stroke Spastic Muscle Stiffness Using Shear Wave Ultrasound Elastography

Current clinical evaluations of post-stroke upper limb spasticity are subjective and qualitative. We proposed a quantitative measurement of post-stroke spastic muscle stiffness by using shear-wave ultrasound elastography and tested its reliability. Acoustic radiation force impulse with shear wave velocity (SWV) detection was used to evaluate stiffness of the biceps brachii muscles at 90° and 0° elbow flexion. In 21 control subjects, SWV did not significantly differ between dominant and non-dominant sides at either flexion angle (0°: p = 0.311, 90°: p = 0.436). In 31 patients who had recent stroke, SWV was significantly greater on the paretic side than on the non-paretic side at both 90° (2.23 ± 0.15 m/s vs. 1.88 ± 0.08 m/s, p = 0.036) and 0° (3.28 ± 0.11 m/s vs. 2.93 ± 0.06 m/s, p = 0.002). The physical appearance of arms and forearms of our patients and controls prevented blinding of the rater to paretic or non-paretic side. At 90°, SWV on the paretic side correlated positively with modified Ashworth scale and modified Tardieu scale (spasticity severity) and negatively with Stroke Rehabilitation Assessment of Movement score (motor function impairment). The intra-class correlation coefficients of intra-rater and inter-rater reliability for SWV measurements were classified as excellent. In conclusion, high SWV was associated with high spasticity and poor function of the post-stroke upper limb, suggesting possible use as a reliable quantitative measure for disease progression and treatment follow-up.     

Correlation of Stiffness of Prostate Cancer Measured by Shear Wave Elastography with Grade Group: A Preliminary Study

The aim of study was to explore the correlation between shear wave elastography (SWE) and grade group (GG) of prostate cancer (PCa). This retrospective study involved prostate-specific antigen elevated patients with elevated prostate-specific antigen levels who underwent SWE before transrectal ultrasound-guided needle biopsy. A total of 49 PCa lesions were reviewed after radical prostatectomy; 3–7 regions of interest were placed within the cancerous area on axial view compared with the tumor foci outlined on the slides by pathologist. The maximum SWE value was measured, quantitative SWE parameters (E_max, E_mean, E_min and standard deviation [SD]) were recorded and correlated with GG and then parameters were compared between indolent (≤2) and aggressive (≥3) GGs. The diagnostic value of each parameter was compared with the receiver operating characteristic curve. Forty-nine PCa foci were divided into two groups on the basis of their GGs. All SWE parameters exhibited a significant linear trend with GG. The area under the receiver operating characteristic curve (AUC) was 0.816 for E_max; with a cutoff point of 84 kPa, sensitivity and specificity were 81.3% and 82.4% to differentiate low and high GGs in PCa. The AUC was 0.776 for E_mean; with a cutoff point of 71 kPa, sensitivity and specificity were 78.1% and 76.5%. For E_min, the AUC was 0.739; with a cutoff point of 60 kPa, sensitivity and specificity were 68.8% and 70.6%. For SD, the AUC was 0.681; with a cutoff point of 8.3 kPa, sensitivity and specificity were 46.9% and 94.1%. There were no significant differences between the four SWE parameters (p < 0.05 for all). SWE features were correlated with GGs, and this correlation may have excellent diagnostic performance in predicting high GG in PCa.     

Shear Wave Elastography Assessment of Carotid Plaque Stiffness: In Vitro Reproducibility Study

This study assessed inter- and intra-observer reproducibility of shear wave elastography (SWE) measurements in vessel phantoms simulating soft and hard carotid plaque under steady and pulsatile flow conditions. Supersonic SWE was used to acquire cine-loop data and quantify Young’s modulus in cryogel vessel phantoms. Data were acquired by two observers, each performing three repeat measurements. Mean Young’s modulus was quantified within 2-mm regions of interest averaged across five frames and, depending on vessel model and observer, ranged from 28 to 240 kPa. The mean inter-frame coefficient of variation (CV) was 0.13 (range: 0.07–0.18) for observer 1 and 0.14 (range: 0.12–0.16) for observer 2, with mean intra-class correlation coefficients (ICCs) of 0.84 and 0.83, respectively. The mean inter-operator CV was 0.13 (range: 0.08–0.20), with a mean ICC of 0.76 (range: 0.69-0.82). Our findings indicate that SWE can quantify Young’s modulus of carotid plaque phantoms with good reproducibility, even in the presence of pulsatile flow.     

The Role of Viscosity Estimation for Oil-in-gelatin Phantom in Shear Wave Based Ultrasound Elastography

Shear wave based ultrasound elastography utilizes mechanical excitation or acoustic radiation force to induce shear waves in deep tissue. The tissue response is monitored to obtain elasticity information about the tissue. During the past two decades, tissue elasticity has been extensively studied and has been used in clinical disease diagnosis. However, biological soft tissues are viscoelastic in nature. Therefore, they should be simultaneously characterized in terms of elasticity and viscosity. In this study, two shear wave-based elasticity imaging methods, shear wave dispersion ultrasound vibrometry (SDUV) and acoustic radiation force impulsive (ARFI) imaging, were compared. The discrepancy between the measurements obtained by the two methods was analyzed, and the role of viscosity was investigated. To this end, four types of gelatin phantoms containing 0%, 20%, 30% and 40% castor oil were fabricated to mimic different viscosities of soft tissue. For the SDUV method, the shear elasticity μ₁ was 3.90 ± 0.27 kPa, 4.49 ± 0.16 kPa, 2.41 ± 0.33 kPa and 1.31 ± 0.09 kPa; and the shear viscosity μ₂ was 1.82 ± 0.31 Pa•s, 2.41 ± 0.35 Pa•s, 2.65 ± 0.13 Pa•s and 2.89 ± 0.14 Pa•s for 0%, 20%, 30% and 40% oil, respectively in both cases. For the ARFI measurements, the shear elasticity μ was 7.30 ± 0.20 kPa, 8.20 ± 0.31 kPa, 7.42 ± 0.21 kPa and 5.90 ± 0.36 kPa for 0%, 20%, 30% and 40% oil, respectively. The SDUV results demonstrated that the elasticity first increased from 0% to 20% oil and then decreased for the 30% and 40% oil. The viscosity decreased consistently as the concentration of castor oil increased from 0% to 40%. The elasticity measured by ARFI showed the same trend as that of the SDUV but exceeded the results measured by SDUV. To clearly validate the impact of viscosity on the elasticity estimation, an independent measurement of the elasticity and viscosity by dynamic mechanical analysis (DMA) was conducted on these four types of gelatin phantoms and then compared with SDUV and ARFI results. The shear elasticities obtained by DMA (3.44 ± 0.31 kPa, 4.29 ± 0.13 kPa, 2.05 ± 0.29 kPa and 1.06 ± 0.18 kPa for 0%, 20%, 30% and 40% oil, respectively) were lower than those by SDUV, whereas the shear viscosities obtained by DMA (2.52 ± 0.32 Pa·s, 3.18 ± 0.12 Pa·s, 3.98 ± 0.19 Pa·s and 4.90 ± 0.20 Pa·s for 0%, 20%, 30% and 40% oil, respectively) were greater than those obtained by SDUV. However, the DMA results showed that the trend in the elasticity and viscosity data was the same as that obtained from the SDUV and ARFI. The SDUV results demonstrated that adding castor oil changed the viscoelastic properties of the phantoms and resulted in increased dispersion of the shear waves. Viscosity can provide important and independent information about the inner state of the phantoms, in addition to the elasticity. Because the ARFI method ignores the dispersion of the shear waves, namely viscosity, it may bias the estimation of the true elasticity. This study sheds further light on the significance of the viscosity measurements in shear wave based elasticity imaging methods.     

2-D Ultrasound Shear Wave Elastography With Multi-Sphere-Source External Mechanical Vibration: Preliminary Phantom Results

Ultrasound shear wave elastography (SWE) imaging is emerging as a quantitative and non-invasive tissue characterization modality. Shear wave generation using external mechanical vibration (EMV) has received extensive research interest over acoustic radiation force impulse (ARFI) because of its low cost and potential for portability. In this paper, we propose an EMV concept with multiple spherical sources that can be easily reconfigured in three configurations to induce unique shear wave propagation patterns. We introduce two design embodiments of this concept bench test design for proof of concept and a clinically deployable design. The latter is designed to incorporate size, ergonomics, portability and power consumption considerations and constraints. Experimental validation on elasticity phantoms using both EMV designs demonstrates shear wave generation and elasticity reconstruction comparable in performance to ElastQ, a commercial ARFI-based shear elastography technology from Philips. In addition, the local displacement amplitude induced by EMV is 10 times greater than that induced by ARFI at the same given depth. Finally, the multiple configurations of the presented EMV design would allow exploration of advanced elastography methods such as tissue anisotropic elasticity.     

Evaluation of Microwave Ablation Efficacy by Strain Elastography and Shear Wave Elastography in ex Vivo Porcine Liver

The aim of this study was to evaluate the efficacy of microwave ablation by ultrasound (US), strain elastography (SE) and shear-wave elastography (SWE). An ex vivo model of porcine liver was adopted. According to ablation power and duration, 30 samples were divided into three groups: group 1 (45 W, 30 s), group 2 (45 W, 15 s) and group 3 (30 W, 30 s). US was used to measure the largest transverse diameter (D1), vertical diameter (D2) and anteroposterior diameter (D3) of the ablated area. SE was used to measure the largest transverse diameter (SEL1), vertical diameter (SEL2) and anteroposterior diameter (SEL3). The actual size of the ablated area was measured as the largest transverse diameter (L1), vertical diameter (L2) and anteroposterior diameter (L3). SWE values and temperatures were measured in the central lesion (region a), marginal area (region b) and unablated area (region c). At 1 h post-ablation, the values measured by US (D1, D2, D3) were all significantly smaller than the ablated area (L1, L2, L3) in all three groups. Except for SEL2 in group 1, there was no significant difference in the results between SEL and L among the three groups. All SWE results were significantly higher post-ablation than pre-ablation in the central lesion (region a) and marginal area (region b, all p values <0.05). In regions a, b and c, the temperatures measured immediately and 5 min post-ablation were all higher than that measured pre-ablation. These results suggest that SE and SWE can be used to evaluate the ablation efficacy of liver tissue.     

A Novel,Reliable Protocol to Objectively Assess Scar Stiffness Using Shear Wave Elastography

The aim of this research was to investigate the use of shear wave elastography as a novel tool to quantify and visualize scar stiffness after a burn. Increased scar stiffness is indicative of pathologic scarring which is associated with persistent pain, chronic itch and restricted range of movement. Fifty-five participants with a total of 96 scars and 69 contralateral normal skin sites were evaluated. A unique protocol was developed to enable imaging of the raised and uneven burn scars. Intra-rater and inter-rater reliability was excellent (intra-class correlation coefficient >0.97), and test–retest reliability was good (intra-class correlation coefficient >0.85). Shear wave elastography was able to differentiate between normal skin, pathologic scars and non-pathologic scars, with preliminary cutoff values identified. Significant correlations were found between shear wave velocity and subjective clinical scar assessment (r = 0.66). Shear wave elastography was able to provide unique information associated with pathologic scarring and shows promise as a clinical assessment and research tool.     

Quantitative Assessment of Skin Stiffness Using Ultrasound Shear Wave Elastography in Systemic Sclerosis

This study was aimed at investigating the performance of ultrasound shear wave elastography (US-SWE) in the assessment of skin (the dermis) stiffness in patients with systemic sclerosis (SSc). The thickness and elastic modulus of the skin were measured using US-SWE at 6 sites in 60 SSc patients and 60 healthy volunteers: the bilateral middle fingers and forearms and the anterior chest and abdomen. To evaluate clinical scores, the measurements were also extended to 17 skin sites in 30 patients. The diagnostic performance of US-SWE in the differentiation of SSc from healthy skin was determined by receiver operating characteristic (ROC) curve analysis, and the reliability of the measurement was evaluated with intra- and inter-class correlation coefficients. The results of US-SWE were compared with modified Rodnan skin thickness scores. Our results indicated that (i) the elastic modulus values were significantly higher in SSc patients than in controls, with or without normalization by skin thickness; (ii) receiver operating characteristic analysis revealed normalized US-SWE cutoff values with a very high accuracy for right and left fingers (areas under the curve?=?0.974 and 0.949), followed by left forearm (0.841), anterior abdomen (0.797), right forearm (0.772) and anterior chest (0.726); (iii) the reliability of US-SWE measurements was good for all examined sites with intra-observer correlation coefficients of 0.845–0.996 and inter-observer correlation coefficients of 0.824–0.985; and (iv) total scores of skin involvement determined at 17 sites (modified Rodnan skin thickness scores) correlated with skin stiffness (r?=?0.832) and thickness (r?=?0.736). In conclusion, US-SWE is a quantitative method with high specificity, sensitivity and reliability in the detection of SSc involvement. This non-invasive, real-time and operator-independent imaging technique could be an ideal tool for the assessment of SSc disease.     

Assessing Liver Stiffness by 2-D Shear Wave Elastography in a Healthy Cohort

The aim of this study was to assess the normal ranges of liver stiffness measurements (LSMs) in participants with healthy livers, using General Electric 2-D shear wave elastography (2-D-SWE-GE) compared with transient elastography (TE). We included 80 participants with healthy livers and without known liver disease, in whom liver stiffness was evaluated in the same session using two elastographic methods, TE and 2-D-SWE-GE. Reliable LSMs were defined for TE as the median of 10 measurements with a success rate of ≥60% and an interquartile range (IQR)?<?30%, and for 2-D-SWE-GE, as the median of 10 measurements acquired in a homogenous area and an IQR?<?30%. Participants with LSMs?>?6.5?kPa by TE were excluded. Reliable LSMs were obtained in 79 participants (98.7%) by means of 2-D-SWE-GE and in 80 participants (100%) by means of TE (p?=?0.9). The mean LSM obtained by 2-D-SWE-GE in our cohort of participants with healthy livers was 5.1?±?1.3?kPa, which was significantly higher than the LSM assessed by TE (4.3?±?0.9?kPa, p?<?0.0001). In 2-D SWE-GE, mean LSMs were significantly higher for men than for women, 5.9?±?1.2?kPa versus 4.7?±?1.2?kPa (p?=?0.0005). In conclusion, 2-D-SWE-GE has very good feasibility (98.7%) in healthy persons. The mean LSM determined by 2-D-SWE-GE in healthy participants was 5.1?±?1.3?kPa. LSMs obtained by means of 2-D-SWE-GE were higher than those obtained by TE in participants with healthy livers.