The locking attachment plate for proximal fixation of periprosthetic femur fractures-a biomechanical comparison of two techniques

Purpose

Mechanical properties of a locking attachment plate construct (LAP-LCP), allowing bicortical screw placement laterally to the prosthesis stem, are compared to a cerclage-LCP construct.

Methods

Eight right synthetic femora with implanted uncemented hip endoprosthesis were cut distally and fixed with LCP, monocortical locking screws and either LAP (n = 4) or cerclage (n = 4). Cyclic testing was performed with monotonically increasing sinusoidal load until failure. Relative movements at the plate–femur interface were registered by motion tracking. Statistical differences were detected by unpaired t-test and general linear model repeated measures.

Results

Stiffness of the LAP-LCP was significantly higher at the beginning (875.4 N/mm ± 29.8) and after 5000 cycles (1213.0 N/mm ± 101.1) compared to the cerclage-LCP (644.96 N/mm ± 50.1 and 851.9 N/mm ± 81.9), with p = 0.013. Relative movements for AP-bending (B) and axial translation (T) of the LAP-LCP at the beginning (0.07° ± 0.02, 0.20 mm ± 0.08), after 500 cycles (0.16° ± 0.10, 0.26 mm ± 0.07) and after 5000 cycles (0.26° ± 0.11, 0.31 mm ± 0.07) differed significantly from the cerclage-LCP (beg.: 0.26° ± 0.04, 0.28 mm ± 0.05; 500 cyc: 0.47° ± 0.03, 0.53 mm ± 0.07; 5000 cyc.: 0.63° ± 0.18, 0.79 mm ± 0.13), with B: p = 0.02, T: p = 0.04. Relative movements for medial bending were not significantly different between the two constructs. Cycles to failure (criterion 1 mm axial translation) differed significantly between LAP-LCP (19,519 ± 1,758) and cerclage-LCP (11,265 ± 2,472), with p = 0.035.

Conclusions

Biomechanically, the LAP-LCP construct improves proximal fixation of periprosthetic fractures compared to the cerclage-LCP construct.     

Biomechanical analysis of two fixation methods for proximal chevron osteotomy of the first metatarsal

Purpose

The proximal chevron osteotomy provides high correctional power. However, relatively high rates of dorsiflexion malunion of up to 17 % are reported for this procedure. This leads to insufficient weight bearing of the first ray and therefore to metatarsalgia. Recent biomechanical and clinical studies pointed out the importance of rigid fixation of proximal metatarsal osteotomies. Therefore, the aim of the present study was to compare biomechanical properties of fixation of proximal chevron osteotomies with variable locking plate and cancellous screw respectively.

Methods

Ten matched pairs of human fresh frozen cadaveric first metatarsals underwent proximal chevron osteotomy with either variable locking plate or cancellous screw fixation after obtaining bone mineral density. Biomechanical testing included repetitive plantar to dorsal loading from 0 to 31 N with the 858 Mini Bionix^® (MTS^® Systems Corporation, Eden Prairie, MN, USA). Dorsal angulation of the distal fragment was recorded.

Results

The variable locking plate construct reveals statistically superior results in terms of bending stiffness and dorsal angulation compared to the cancellous screw construct. There was a statistically significant correlation between bone mineral density and maximum tolerated load until construct failure occurred for the screw construct (r = 0.640, p = 0.406).

Conclusion

The results of the present study indicate that variable locking plate fixation shows superior biomechanical results to cancellous screw fixation for proximal chevron osteotomy. Additionally, screw construct failure was related to levels of low bone mineral density. Based on the results of the present study we recommend variable locking plate fixation for proximal chevron osteotomy, especially in osteoporotic bone.     

Routine use of locking shaft screws is not necessary in volar plate fixation of distal radius fractures

Hypothesis

Volar locking plate fixation is a common treatment method for distal radius fractures. Recently, implants have been designed with an option to use locking screws in the shaft portion of the plate. While there is a high incidence of low bone mineral density in patients who sustain fragility fractures of the distal radius, the need for locking shaft screws is not well defined. Our hypothesis is that the routine use of locking screws in the shaft portion of volar plates is not required to maintain reduction or to prevent hardware failure.

Methods

A retrospective review was performed in all patients over age 50 years who underwent volar plate fixation using an implant with non-locking shaft screws for a distal radius fracture during a 2-year period. Patients were permitted to perform early range of motion exercises. Radiographs were examined and measurements were obtained to assess maintenance of reduction and incidence of hardware failure. Patients were followed at least until fracture healing. Patients were excluded from analysis if locking shaft screws were utilized or if follow-up was inadequate.

Results

Forty-one patients met the inclusion criteria. The average age was 62 years (range 50–79). There were 12 men and 29 women. The implant used incorporated 3.5-mm shaft screws in 26 patients and 2.4-mm shaft screws in 15 patients. All patients healed within acceptable radiographic parameters (mean volar tilt = 4.9°, mean radial inclination = 21.7°, mean radial height = 11.6 mm). There were not any instances of hardware failure.

Discussion

Distal radius fractures frequently occur in patients with low bone mineral density. Non-locking, bicortically placed shaft screws provide adequate stability to allow for early range of motion without loss of reduction or hardware failure. The routine use of locking screws in the shaft portion of volar plates does not appear justified.     

Locking Buttons Increase Fatigue Life of Locking Plates in a Segmental Bone Defect Model

Background

Durability of plate fixation is important in delayed union. Although locking plates result in stronger constructs, it is not known if locking affects the fatigue life of a plate. Two locking screws on either side of the nonunion could decrease working length and increase strain in the plate. However, the reinforcing effect of the locking head on the plate may compensate, so that it is unclear whether locking reduces fatigue life.

Questions/purposes

We determined whether locking screws, compression screws, and locking buttons reduce or increase the fatigue life of a plate.

Methods

We tested fatigue life of four constructs using an eight-hole locking plate in a segmental defect model: (1) all locking screws (Locked; n = 5); (2) all compression screws (Unlocked; n = 5); (3) six compression screws with two locking buttons in the central holes (Button; n = 6); and (4) six compression screws with two open central holes (Open; n = 6).

Results

The Button group had the longest fatigue life (1.3 million cycles). There was no difference between the Locked and Unlocked groups. All of the constructs failed by fracture of the plates through a screw hole adjacent to the defect.

Conclusions

Locking screws did not improve fatigue life, however a locking button increased the fatigue life of a locking plate in a segmental bone defect model.

Clinical Relevance

Locking buttons in holes adjacent to a defect may improve durability, which is important when delayed union is a possibility.     

Treatment of distal tibial shaft fractures by three different surgical methods: a randomized,prospective study

Purpose

A few studies focused on the methods of treatment for displaced distal tibial shaft fractures have been published, all of which compared two different methods. In this randomized, prospective study, we aimed to compare minimally invasive plate osteosynthesis, locking intramedullary nail stabilization and external fixation combined with limited open reduction and absorbable internal fixation for distal tibial shaft fractures by assessing complications and secondary procedures.

Methods

From November 2002 to June 2012, 137 skeletally mature patients with displaced distal tibial shaft fractures with or without fibula fracture were randomized to be treated by minimally invasive plate osteosynthesis (group A, n = 46), locking intramedullary nail (group B, n = 46) or external fixation combined with limited open reduction and absorbable internal fixation (group C, n = 45). Age, gender, mechanism of injury, fracture pattern and presence of open fracture were equally distributed among the three groups. Indexes for evaluation included hospital stay, operative time, time to radiographic union, union status, infection and the incidence of re-operation. Mazur ankle score was introduced for functional evaluation. Statistics Analysis System (SAS) 9.2 was used for analysis.

Results

A total of 121 patients were included in the final analysis (group A 42, group B 40 and group C 39) and evaluated after a mean of 14.8 months follow-up. There was no significant difference (P > 0.05) in hospital stay, time to radiographic union and the incidence of union status among the three groups. Although group C was associated with less secondary procedures versus groups A and B, it was related with more pin tract infections (15.4 %). Anterior knee pain occurred frequently after locking intramedullary nailing (37.5 %) and the irritation symptoms were more frequently encountered in group A (59.5 %). There was no difference in ankle function between the three methods after operation (P > 0.05).

Conclusions

We consider that the minimally invasive plate osteosynthesis, locking intramedullary nail stabilization and external fixation combined with limited open reduction and absorbable internal fixation techniques are all efficient methods for treating distal tibia fractures. With its wide indications, external fixation combined with limited open reduction and absorbable internal fixation leads to minimal soft tissue complication, good functional result and no local soft tissue irritation or implant removal.     

Proximal femoral nails compared with reverse distal femoral locking plates in intertrochanteric fractures with a compromised lateral wall; a randomised controlled trial

Purpose

There is no consensus about the best option of internal fixation for unstable intertrochanteric fractures. The aim of the present study was to compare proximal femoral nail (PFN) with contralateral reverse distal femoral locking compression plate (reverse-DFLCP) in the management of unstable intertrochanteric fractures with compromised lateral wall.

Method

In a randomized controlled study, from November 2011 to October 2012, 40 patients with unstable intertrochanteric fractures with compromised lateral wall (AO 31A 2.2 to 3.3) had osteosynthesis by PFN (n = 20) or reverse-DFLCP (n = 20). Intra-operative variables compared were duration of surgery, blood loss during surgery, fluoroscopy time and surgeons perception of the surgery. Patients were followed up clinically for a minimum of one year. Functional outcome was assessed by Parker Palmer mobility score (PPMS), Harris hip score (HHS), and Short Form-12. Failure was defined as any condition which would necessitate revision surgery with change of implant.

Results

Duration of surgery (p = 0.022), blood loss during surgery (p = 0.008) and fluoroscopy time (p = 0.0001) were significantly less in the PFN group than in the reverse-DFLCP group. No significant difference was found in type of reduction, difficulty in reduction and surgeon’s perception of surgery. The PFN group had better functional outcome than the reverse-DFLCP group. HHS for the PFN group was 81.53 ± 13.21 and for the reverse-DFLCP group it was 68.43 ± 14.36 (p = 0.018). SF-12 physical (p = 0.002) and mental component (p = 0.007) scores in the PFN group was significantly better than in the reverse-DFLCP group. There was one failure in the PFN group as compared to six in the reverse-DFLCP group (p = 0.036).

Conclusion

Due to favourable intra-operative variables, better functional outcome and lower failure rates, we conclude that PFN is a better implant than reverse-DFLCP for intertrochanteric fractures with compromised lateral wall.Keyword: Unstable intertrochanteric fractures, Lateral wall, Proximal femoral nail, Reverse distal femoral locking compression plate     

Intramedullary repair device against volar plating in the reconstruction of extra-articular and simple articular distal radius fractures; a randomized pilot study

Purpose

This prospective randomized pilot study reports our institutional experience and early results using Sonoma Wrx (Sonoma Orthopedic Products, Santa Rosa, CA) in the treatment of extra-articular and simple intra-articular distal radius fractures.

Material and methods

A total of 64 patients, were enrolled in the study. They were considered eligible if they had; unstable extra-articular distal radius fractures and simple intra-articular distal radius fractures suitable for closed reduction (AO types; A2.2, A2.3, A3.1 C2.1, C2.2). Patients in group I received intramedullary fixation using the Sonoma Wrx® device and patients in group II received standard volar locking plate fixation. Radiographic criteria of acceptable healing were used for evaluation.

Results

Two groups were similar in terms of baseline characteristics. Mean time of operation was significantly shorter in Group 1 vs. in group 2 (36.81 ± 7.11 vs. 48.97 ± 5.9 minutes, p = 0.001). Time to healing of the fracture was not different between two groups (5.45 ± 1.09 vs. 5.70 ± 1.04 weeks for Group 1 vs. 2, respectively p = 0.36). Overall complications occurred in 9 patients in group 1 and in 15 patients in group 2 (p = 0.17). Follow-up was completed in all patients with a median time of 12 months and 13 months in group 1 and 2, respectively. On radiographic evaluation radial inclination, radial height and volar tilt were not significantly different between group 1 and 2, respectively. There were no significant differences between two groups in regard to wrist rotational degrees measured in last follow-up visit.

Conclusion

Sonoma Wrx Device is reliable and effective in terms of achieving satisfactory outcomes in treatment of distal radius fractures. It may be reasonable to use this device to prevent complications that are related to extensive soft tissue dissection.     

Comparison of Kirschner wires and AO cannulated screw internal fixation for displaced lateral humeral condyle fracture in children

Purpose

This retrospective study compares Kirschner wires versus 3.5-mm diameter AO cannulated screw internal fixation in treatment for the displaced lateral humeral condyle fractures.

Methods

The study included 62 patients (42 boys, 20 girls; mean age 6.93 years; age range two to 14 years) with displaced lateral humeral condyle fractures. All patients were treated by open reduction and Kirschner wires or cannulated screw fixation. The clinical outcomes were evaluated according to the criteria of Hardacre et al. The mean follow-up period was 39.4 months (range 21–95 months).

Results

There was no statistically significant difference in clinical outcome between these two groups (P > 0.05). Five patients (16.7%) developed skin infection around K-wires, while no infection occurred in fracture with screws. An obvious lateral prominence occurred in 11 (36.7%) patients with K-wires and four (12.5%) patients with screws. Nine (30%) patients with K-wires and two (6.3%) patients with screws had a lack of 10° of extension of the elbow compared with the other side.

Conclusion

Both K-wires and cannulated screw fixation are effective in treatment for displaced lateral humeral condyle fracture. K-wires can pass through the ossific nucleus of capitulum without damaging it, but a longer period of external fixation and local skin care will be required. The screws can reduce the possibility of lateral prominence and promote the function of elbow by continuously stabilising the fracture, but a second operation is need for screw removal.     

Comparison of the efficacy of a distal clavicular locking plate versus a clavicular hook plate in the treatment of unstable distal clavicle fractures and a systematic literature review

Purpose

The purpose of this study was to retrospectively compare and review the clinical outcomes between the distal clavicular locking plate and clavicular hook plates in the treatment of unstable distal clavicle fractures; moreover, the relevant literature of the two fixation methods was reviewed systematically to identify the non-union, complications, or functional scores, according to the treatment methods and determine which treatment method is better.

Methods

Sixty-six patients with 66 unstable distal clavicle fractures who underwent open reduction and internal fixation with either a distal clavicular locking plate (36 patients) or a clavicular hook plate (30 patients ) were evaluated. The main outcome comparisons included Constant score, rate of non-union, rate of complication, and rate of returning to work three months postoperatively.

Results

No significant difference was found between locking plate and hook plate groups in union rate and Constant score (P > 0.05). However, the results indicated that the distal clavicular locking plate group had a significantly lower rate of complications (P < 0.05) and symptomatic hardware (P < 0.05). In addition, the distal clavicular locking plate facilitated the return to work better than the clavicular hook plate (P < 0.05).

Conclusions

Both distal clavicular locking plate and clavicular hook plate achieved good results in the treatment of unstable distal clavicle fractures; however, internal fixation with a distal clavicular locking plate had greater ability to return to their previous work after surgery in three months and fewer complications than the clavicular hook plate.     

Three-dimensional computer-assisted navigation for the placement of cannulated hip screws. A pilot study

Purpose

Medial femoral neck fractures are common, and closed reduction and internal fixation by three cannulated screws is an accepted method for the surgical treatment. Computer navigation for screw placement may reduce fluoroscopy time, the number of guidewire passes and optimise screw placement.

Methods

In the context of a sawbone study, a computer-assisted planning and navigation system based on 3D-imaging for guidewire placement in the femoral neck was tested to improve screw placement. Three screws were inserted into 12, intact, femoral sawbones using the conventional technique and into 12, intact, femoral sawbones guided by the computer-based navigation system. Guidewire and subsequent screw placement in the femoral neck were evaluated.

Results

Use of the navigation system resulted in a significant reduction of the number of drilling attempts (p ≤ 0.05) and achieved optimised accuracy of implant placement by attaining significantly better screw parallelism (p ≤ 0.05) and significantly enlarged neck-width coverage by the three screws (p ≤ 0.0001). Computer assistance significantly increased the number of fluoroscopic images (p ≤ 0.001) and the operation time (p ≤ 0.0001).

Conclusions

Three-dimensional computer-assisted navigation improves accuracy of cannulated screw placement in femoral neck while increasing the number of fluoroscopic images and operation time. Additional studies including fractured sawbones and cadaver models with the goal of reducing operation time are indispensable before introduction of this navigation system into clinical practice.     

Internal fixation of femoral neck fractures with posterior comminution: a biomechanical comparison of DHS® and Intertan nail®

Background and purpose

Internal fixation is a therapeutic mainstay for treatment of undisplaced femoral neck fractures and fractures without posterior comminution. The best treatment for unstable and comminuted fractures, however, remains controversial, especially in older patients. The present study was designed to assess the utility of the Intertan Nail® (IT) for stabilization of comminuted Pauwels type III fractures compared to dynamic hips screw (DHS).

Methods

Randomized on the basis of bone mineral density, 32 human femurs were assigned to four groups. Pauwels type III fractures were osteomized with a custom-made saw guide. In 16 specimens the posteromedial support was removed and all femurs were instrumented with an IT or a DHS. All constructs were tested with nondestructive axial loading to 700N, cyclical compression to 1,400N (10,000 cycles), and loading to failure. Outcome measures included number of survived cycles, mechanical stiffness, head displacement and load to failure.

Results

Postoperative mechanical stiffness and stiffness after cyclical loading were significantly reduced in all constructs regardless of the presence of a comminution defect (p = 0.02). Specimens stabilized with the IT had a lower construct displacement (IT, 8.5 ± 0.5 mm vs. DHS, 14.5 ± 2.2 mm; p = 0.007) and sustained higher failure loads (IT, 4929 ± 419 N vs. DHS, 3505 ± 453 N; p = 0.036) than the DHS constructs.

Interpretation

In comminuted Pauwels type III fractures, the fixation with the IT provided sufficient postoperative mechanical strength, comparable rate of femoral head displacement, and a similar tolerance of physiological loads compared to fractures without comminution. The absence of the posteromedial support in comminuted fractures tended to reduce the failure load regardless of the fixation method.     

The best location for proximal locking screw for femur interlocking nailing: A biomechanical study

Background:

Proximal locking screw deformation and screw fracture is a frequently seen problem for femur interlocking nailing that affects fracture healing. We realized that there is lack of literature for the right level for the proximal locking screw. We investigated the difference of locking screw bending resistance between the application of screws on different proximal femoral levels.

Materials and Methods:

We used a total of 80 proximal locking screws for eight groups, 10 screws for each group. Three-point bending tests were performed on four types of screws in two different trochanteric levels (the lesser trochanter and 20 mm proximal). We determined the yield points at three-point bending tests that a permanent deformation started in the locking screws using an axial compression testing machine.

Results:

The mean yield point value of 5 mm threaded locking screws applied 20 mm proximal of lesser trochanter was 1022 ± 49 (range 986–1057) (mean ± standard deviation, 95% confidence interval). On the other hand, the mean yield point value of the same type of locking screws applied on the lesser trochanteric level was 2089 ± 249 (range 1911–2268). Which means 103% increase of screw resistance between two levels (P = 0.000). In all screw groups, on the lesser trochanter line we determined 98–174% higher than the yield point values of the same type of locking screws in comparison with 20 mm proximal to the lesser trochanter (P = 0.000).

Conclusion:

According to our findings, there is twice as much difference in locking screw bending resistance between these two application levels. To avoid proximal locking screw deformation, locking screws should be placed in the level of the lesser trochanter in nailing of 1/3 middle and distal femur fractures.     

Opening wedge high tibial osteotomy: navigation system compared to the conventional technique in a controlled clinical study

Purpose

This study aimed to verify if the navigation system used in high tibial osteotomy (HTO) adds precision to the procedure regarding mechanical axis correction and prevention of tibial slope increases.

Methods

In this historically controlled study, patients with medial osteoarthrosis and genuvarum underwent HTO between 2004 and 2012; the first 20 were operated with the conventional technique, using pre-planning correction by the Dugdale method and 18 further patients were operated with the navigation system introduced in our hospital.

Results

The two groups were similar for pre-operative mechanical axis (mean 8.10 ± 3.14 for the control and 6.60 ± 2.50 for the navigated group), pre-operative tibial slope (mean 8.95 ± 3.47 versus 8.17 ± 3.11, respectively) and Lyshom score (40.85 ± 15.46 and 44.83 ± 16.86). After surgery, the control group presented mean mechanical axis of 3.35 ± 3.27, tibial slope of 13.75 ± 3.75 and Lyshom score of 87.60 ± 11.12. The navigated group showed a postoperative mechanical axis mean of 3.06 ± 1.70, tibial slope of 10.11 ± 0.18 and Lyshom score of 91.94 ± 11.61.

Conclusions

The navigation system allowed a significantly better control of tibial slope. Patients operated with the navigation system had significantly better Lysholm scores.     

Fibular fixation as an adjuvant to tibial intramedullary nailing in the treatment of combined distal third tibia and fibula fractures: a biomechanical investigation

Objective

Distal third tibia fractures have classically been treated with standard plating, but intramedullary (IM) nailing has gained popularity. Owing to the lack of interference fit of the nail in the metaphyseal bone of the distal tibia, it may be beneficial to add rigid plating of the fibula to augment the overall stability of fracture fixation in this area. This study sought to assess the biomechanical effect of adding a fibular plate to standard IM nailing in the treatment of distal third tibia and fibula fractures.

Methods

Eight cadaveric tibia specimens were used. Tibial fixation consisted of a solid titanium nail locked with 3 screws distally and 2 proximally, and fibular fixation consisted of a 3.5 mm low-contact dynamic compression plate. A section of tibia and fibula was removed. Testing was accomplished with an MTS machine. Each leg was tested 3 times; with and without a fibular plate and with a repetition of the initial test condition. Vertical displacements were tested with an axial load up to 500 N, and angular rotation was tested with torques up to 5 N•m.

Results

The difference in axial rotation was the only statistically significant finding (p = 0.003), with fibular fixation resulting in 1.1° less rotation through the osteotomy site (17.96° v. 19.10°). Over 35% of this rotational displacement occurred at the nail–locking bolt interface with the application of small torsional forces.

Conclusion

Fibular plating in addition to tibial IM fixation of distal third tibia and fibula fractures leads to slightly increased resistance to torsional forces. This small improvement may not be clinically relevant.     

Cartilage repair of the knee with Hyalograft C:® Magnetic Resonance Imaging assessment of the glycosaminoglycan content at midterm

Purpose

The aim of this study was to assess the stability of the glycosaminoglycan (GAG) content in the long term after matrix-associated autologous chondrocyte transplantation (MACT) with Hyalograft C in the knee over a follow-up period of one year.

Methods

In this cross-sectional evaluation, 11 patients after MACT of the knee consented to delayed gadolinium-enhanced magnetic resonance imaging of cartilage (dGEMRIC) measurements. The mean post-operative interval before the first MR examination was 40.6 ± 22.0 months, and the second MR examination was carried out after another 12 months. The Lysholm score was assessed for clinical evaluation. Quantitative T1 measurements after intravenous negatively charged MR contrast agent administration were performed. Global post-contrast T1 of the reference cartilage and the repair tissue and a relative post-contrast T1 value were calculated.

Results

The Lysholm score improved significantly from 59.8 ± 12.9 at baseline to 86.1 ± 15.7 at the second visit (p < 0.01). The mean global T1 of the repair tissue (1st visit 581.3 ± 126.4 ms; 2nd visit 684.1 ± 169.9 ms; p = 0.104) and the mean relative T1 value showed stable results over one year (1st visit 0.81 ± 0.28; 2nd visit 0.76 ± 0.32; p = 0.4).

Conclusions

The study demonstrated stable glycosaminoglycan content of the repair tissue after MACT at midterm.     

Patient-reported outcomes after acute carpal tunnel release in patients with distal radius open reduction internal fixation

Background

Acute carpal tunnel syndrome (CTS) is a complication that can develop after distal radius fractures. Our hypothesis tested whether patient-reported outcomes after acute carpal tunnel release (CTR) performed in combination with distal radius fracture open reduction internal fixation (ORIF) are worse than patient-reported outcomes with only elective CTR as measured by the symptom severity and functional status scales of the Boston carpal tunnel questionnaire (BCTQ).

Methods

A retrospective assessment identified 26 patients treated with acute CTR at the same time as distal radius ORIF, no history of pre-existing CTS or CTR, no other injuries, and >12 months follow-up. Sixteen of these patients (Group A) could be contacted and answered the BCTQ. Group A was age- and sex-matched to control patients (Group B) treated with only elective CTR. A case–control study was performed comparing outcomes of both groups.

Results

The average age of patients was 51 ± 15 years, with an average follow-up of Group A at 49 ± 21 months versus Group B at 55 ± 20 months. The mean symptom severity scale score for Group A was 1.4 ± 0.4 and for Group B was 1.4 ± 0.4. The mean functional status scale score for Group A was 1.4 ± 0.5 and for Group B was 1.3 ± 0.4. The mean total BCTQ score for Group A was 26.5 ± 7.5 and for Group B was 24.9 ± 7.5. There were no statistical or clinically significant differences between Group A and Group B for symptom severity, functional status, and total BCTQ scores.

Conclusions

Patients with acute CTR performed at the same time with distal radius ORIF do as well in the long-term as those patients with only elective CTR as measured by the BCTQ. Patients should expect similar recovery of subjective nerve function from acute median nerve dysfunction when CTR is performed with distal radius ORIF as patients with only elective CTR.     

Anterolateral approach using tibial tubercle osteotomy for total knee arthroplasty: can we predict failure?

Purpose

The purpose of this study was to identify predictive factors for the occurrence of complications in a consecutive series of patients who underwent step-cut tibial tubercle osteotomy (TTO) and subsequent screw refixation in primary total knee arthroplasty (TKA).

Methods

Using standardised conventional radiographs, critical parameters including TTO length and depth, proximal abutment width (OT), and orientation and placement of fixation screws were measured in 422 patients (mean age of 71 years and a follow-up time range of one to five years) with two screw fixations.

Results

Medial spatial orientation in the distal screw (11 %, p=0.046), the TTO length (<55.4 mm, p=0.013), the OT width (<14 mm, p=0.002) and the distance of the distal refixation screw from the TKA (<51.7 mm, p=0.003) were significant factors for the occurrence of complications.

Conclusions

Age, gender, comorbidities, height, weight and/or the body mass index had no significant influence on the occurrence of complications. The TTO-related complication rate was 3 %. Consideration of these key surgical factors leads to improved outcomes.     

Critical analysis of tibial fracture healing following unreamed nailing

Purpose

Unreamed nails have revolutionised the treatment of tibial shaft fractures. Many authors, however, have reported increasing bone healing complications with these implants. Unfortunately, few studies have addressed the factors affecting bone healing after unreamed tibial nailing.

Methods

One-hundred and sixty tibial fractures in 158 patients (mean age 39.5 years) fixed using unreamed nails were reviewed. There were 78 AO type-A, 65 type-B and 17 type-C fractures (115 closed and 45 open fractures). Twelve patient, injury and surgery variables were analysed for their influence on fracture healing.

Results

Union occurred in all fractures after a mean time of 24.3 weeks. Additional surgery to achieve union, apart from dynamisation, was done in nine (6%) cases. The most important variables affecting healing were the mechanism of trauma (p = 0.005), fracture site gap (p = 0.01), degree of comminution (p = 0.0003), associated soft tissue injuries (p = 0.02) and the time to dynamisation (p = 0.0001).

Conclusions

High-energy trauma and fracture comminution have a negative impact on bone union and require close follow-up. It is essential to avoid distraction over three millimetres with unreamed nailing. Dynamisation is advised within ten weeks in axially stable fractures to encourage bone healing and avoid failure of the locking screws.     

Magnetic Resonance Imaging is not suitable for interpretation of meniscal status ten years after arthroscopic repair

Purpose

The purpose of this study was to assess the MRI features of the all-inside repaired meniscus in the long-term.

Methods

Among 27 consecutive all-inside arthroscopic meniscal repairs, 23 patients aged 25 ± 5 years at the time of surgery were reviewed at a median follow-up of 10 ± 1 years. Retrospective clinical examinations and imaging assessments using a 1.5-T MRI after all-inside arthroscopic meniscal repair were conducted.

Results

At follow-up, Lysholm and IKDC averaged 89 ± 11 and 95 ± 8, respectively. MRI examinations revealed no meniscal signal alteration in three patients (13 %), a vertical signal located in the previously torn area in seven (30 %), a horizontal grade 3 in nine (39 %), and a complex tear (grade 4) in four (17.5 %). There were no differences between medial and lateral menisci (p = 0.15), stable and stabilised knees (p = 0.56).

Conclusions

Several abnormal vertical and/or horizontal hypersignals are still present on MRI examination ten years after arthroscopic all-inside meniscal repair. The appearance of early signs of osteoarthritis is rare, suggesting a chondroprotective effect of the repaired meniscus.     

Minimising the risk of extensor pollicis longus rupture following volar plate fixation of distal radius fractures: a cadaveric study

INTRODUCTION

Rupture of extensor pollicis longus (EPL) tendon is a recognised complication following volar plate fixation of distal radius fractures, usually from attrition caused by prominent screws. We sought to identify the screw holes in some of the most commonly used plates which may precipitate tendon injury.

SUBJECTS AND METHODS

Three fixed-angle volar locking plates were sequentially positioned into 18 cadaveric arms. A wire was passed through each of the holes in the plates using a locking guide and the dorsal relationships noted.

RESULTS

Each plate had specific ‘high-risk’ holes which directed the wire towards the EPL groove. The central screw holes appeared mostly implicated in EPL injury.

CONCLUSIONS

Awareness of ‘high-risk’ holes and appropriate minor alterations in surgical technique may consequently decrease the incidence of EPL irritation and rupture.